Beruflich Dokumente
Kultur Dokumente
UNIT 1
SHORT QUESTIONS:
1.
2.
3.
4.
5.
6.
7.
8. Find out moment distribution factors for the given frame. Consider Moment of inertia I is
uniform throughout.
LONG QUESTIONS:
2
1. Write down the step wise procedure of Kanis method for analyzing beams and frames?
2. Write down step wise procedure to analyze single bay multi storied frame under sway
condition.
3. Write down the step wise procedure of moment distribution method for analyzing frames.
4. Analyze the frame shown in figure by moment distribution method.
6. Analyze the frame shown in figure by moment distribution method. Draw bending moment
diagram.
7. Analyze the structure shown in figure using Kanis method and draw bending moment
diagram.
8. Evaluate the bending moment and shear force diagrams of a beam in figure by the Kanis
method. Consider uniform moment of inertia.
9. A portal frame ABCD is subjected to uniformly distributed load of 2kN/m as shown in figure.
Analyze the frame and sketch bending moment diagram using Kanis method.
10. Analyze the frame shown in figure below by Kanis method, take EI as constant. Consider
length in meters.
UNIT-2
SHORT QUESTIONS:
1. Write down the generalized form of slope deflection equation?
2. What kind of indeterminate structural analysis is slope deflection method?
3. Write down the slope deflection equations for given frame.
5
I0
7. Analyze the given frame using slope deflection method. Draw the bending moment diagram.
8. Analyze the given frame using slope deflection method. Draw the bending moment diagram.
9. Analyze the given frame using slope deflection method. Draw the bending moment diagram.
10. Analyze the given frame using slope deflection method. Draw the bending moment diagram.
UNIT-3
SHORT QUESTIONS:
3. Analyze the framed structure subjected to lateral loads using cantilever method and draw the
bending moment diagram. Assume flexural rigidity is constant.
4. Analyze the framed structure subjected to lateral loads using cantilever method and draw the
bending moment diagram. Assume flexural rigidity is constant.
5. Analyze the framed structure subjected to lateral loads using factor method. Assume flexural
rigidity is constant.
6. Analyze the framed structure subjected to lateral loads using factor method. Assume flexural
rigidity is constant.
7. Write in detail about substitute frame method of analysis. Explain it with an example.
8. Analyze the framed structure subjected to lateral loads using factor method. Assume flexural
rigidity is constant.
9. Analyze the framed structure subjected to lateral loads using cantilever method. Assume
flexural rigidity is constant.
10
10. Explain portal method of analysis for tall framed structures in detail with an example.
UNIT-4
SHORT QUESTIONS:
1. Distinguish between determinate and indeterminate structures.
11
2. Write down the procedure for stiffness method of analysis? Illustrate with an example.
3. Write down the procedure for flexibility method of analysis? Illustrate with an example.
4. Analyze the given structure using stiffness matrix method.
12
6. Use stiffness matrix method to analyze the given truss member. Take area of cross section for
all members 1000 square millimeters and modulus of elasticity is E = 200 kN/mm2.
7. Analyze the given beam ABCD if support B sinks by 10 mm. take EI = 6000 kNm2.use
flexibility method.
8. Analyze the given beam ABCD if support B sinks by 10 mm. take EI = 6000 kNm2.use
flexibility method.
9. Use flexibility matrix method to analyze the given truss member. Take area of cross section
for all members 1000 square millimeters and modulus of elasticity is E = 200 kN/mm2.
13
10. Use displacement method of analysis to solve the given problem. Assume necessary data.
UNIT-5
SHORT QUESTIONS:
1. Define influence lines.
2. State Muller-Breslaus principle.
3. Explain indirect model analysis for influence lines of indeterminate structures.
14
4. Draw the influence line for the support reaction for the propped cantilever beam, propped at
free end.
5. Distinguish between static and kinematic indeterminacies for trusses which are of pin jointed.
6. Distinguish between determinate and indeterminate truss structures which are of pin jointed.
7. State the Castiglianos second theorem.
8. Draw the influence line diagram for simply supported beam with any kind of loading. Take
your load of choice. Find its maximum shear force.
9. State the difference between pin jointed plane frames and rigid jointed plane frames.
10. State the procedure to find determinacy or indeterminacy of a truss.
LONG QUESTIONS:
1. Compute the ordinates of influence lines for reaction RA for the beam shown in figure, at 1m
interval and draw the influence line diagram. EI is constant throughout.
2. Compute the ordinates of influence lines for reaction RA for the beam shown in figure, at 2m
interval and draw the influence line diagram. EI is constant throughout.
3. Using influence line diagrams, determine the bending moment at any point in propped
cantilever.
4. Explain the procedure to find shear force at any point in propped cantilever using influence
line diagrams.
5. Draw influence lines for the following truss. Locate maximum B.M and S.F on diagram.
6. Draw influence lines for the following truss and find bending moment maximum and shear
force maximum. Consider fixed supports at nodes A and E.
15
7. Draw influence lines for the following truss and also find maximum bending moment and
shear forces. Locate them on drawing. Consider fixed supports at nodes A and E.
8. Determine the influence diagram for reaction at A in the continuous beam shown in figure.
Node A is given with fixed support.
10. Compute the ordinates of influence lines for reaction RA for the beam shown in figure, at 1m
interval and draw the influence line diagram. EI is constant throughout.
16