Beruflich Dokumente
Kultur Dokumente
SBM
Project code:
Z13290000
Project
SO17660
Stock Buoy Saigon 2
Document No.:
SSY QC 16
PROJECT DESCRIPTION:
Number of Pages: 93
REVISION STATUS
Rev. No.
Date
Pages
Description
Prepared By SSY
Signature
10 Oct. 07
1 + 92
Date
Reviewed By DNV
Signature
Date
Approved By SBM
Signature
Date
INDUSTRIAL SERVICES
OFFSHORE SERVICES
MARINE SERVICES
Mechanical, Electrical, Piping, Steel Structure , Pressure Vessel Fabrication & Installation.
Oil & Gas Engineering, Offshore Constructions & Maintenance.
Ship Construction, Ship Repair.
INDEX
1. PAINTING PROCEDURE
2. HEMPEL-SBM SPECIFICATION
3. PRODUCT DATA SHEET
4. MATERIAL SAFETY DATA SHEET
5. APPLICATION INSTRUCTION
6. RAL HEMPEL EQUIVALENT TABLE
INDUSTRIAL SERVICES
OFFSHORE SERVICES
MARINE SERVICES
Mechanical, Electrical, Piping, Steel Structure , Pressure Vessel Fabrication & Installation.
Oil & Gas Engineering, Offshore Constructions & Maintenance.
Ship Construction, Ship Repair.
PAINTING PROCEDURE
INDUSTRIAL SERVICES
OFFSHORE SERVICES
MARINE SERVICES
Mechanical, Electrical, Piping, Steel Structure , Pressure Vessel Fabrication & Installation.
Oil & Gas Engineering, Offshore Constructions & Maintenance.
Ship Construction, Ship Repair.
1- SCOPE:
This procedure covers method, equipments and materials to be used for carrying out surface
preparation and coating application, inspection, and touch- up of paint system to be used on
SBM stock Buoy Saigon 2.
2- REFERENCES:
SBM Specification SO17660 SSM 06002 - V1
ISO 8501-1 to 3
ISO 8502-3 to 9
NACE RP 0287
ISO 4624
ISO 4628
ISO 2409
Cross-Cut Test
ASTM A-123
NACE RP0188
NACE RP0287
ISO 19840
RAL 840HR
ASTM D4285
ASTM D4940
SSPC SP 8
SSPC SP 11
SSPC SP12
3- PROCEDURE:
3.1
The paint will be stirred before, during and after mixing by appropriate agitator. All
paint mixing will be done according to manufacturers recommendations in clean
containers and free from traces of grease, other type of paint or other contaminants.
3.2
Surface preparation:
3.2.1
Solvent cleaning:
Solvent cleaning will be generally carried out on contaminated surface to ensure that oil
and grease are removed prior blasting and painting.
3.2.2
Blast cleaning:
A.Prior to blasting preparation :
-
All rough welds, burns, weld spatters, indentation and all sharp surface projection will
be ground smooth (min R=2mm).
Steel surface should be dry and free from oil, grease and contamination prior blasting.
Oil and grease if any will be removed in accordance SSPC-SP1 solvent cleaning.
Abrasive blasting will be done during daylight hours. If abrasive blasting at night is
approved by the SBMs Representative then sweeping clean and bright will be
required the next morning.
Blasting abrasive materials will be clean and dry free from contaminant.
The compressed air supply used to blasting will be free of detrimental amount of water
and oil.
Abrasive blast cleaning operation will always be done when the surface temperature is
a minimum of 3oC (5oF) above dew point and ambient relative humidity is lower than
85%.
Abrasive will be selected such a way that surface profile as recommended by paint
manufacturer is achieved.
All blasted surfaces will be coated immediately before rust starts to appear on the
surface. Oxidized surface will be sweep blasted. Where priming is significantly
delayed by weather condition or for any reason, the surface will be sweep blasted
regardless of its appearance.
3.2.3
Power tool cleaning may be used to obtain the required surface preparation where
abrasive blasting is not possible, these surface shall be 100% cleaned by means of
power brush.
Power tool cleaning will be such a way that the surface is not burnished and keeps
sufficient roughness for good adhesion of the coating.
3.2.4
3.2.5
The surface to be coated will be clean and dry, free from oil, grease and have the
specified roughness and cleanliness until the first coat is applied.
3.3
Coating application:
3.3.1
All materials (Paints & Thinners) and coating application shall be in accordance with the
paint manufacturers recommendations for each specified coating system, to be approved
first by SBM.
3.3.2
Materials will always be prepared by mixing a complete unit proportions supplied. Once
the set has been mixed it must be used within the working pot life specified. Stirring will
follow the basic steps:
1. Agitate base (part A) with a power agitator.
2. Combine entire contents of curing agent (part B) with Base (part A) and mix
thoroughly with power agitator.
3.3.3
Use of thinner will be limited as much as possible and the ratio will always follow
products data sheets (max % by volume). Only thinners specified by the paint supplier will
be used.
3.3.4
When surface temperature is less than 30C above dew point and relative humidity is
greater than 85%.
When the steel or ambient temperature is below 5oC or above 50oC for application of
epoxy products.
3.3.5
Painting will not be allowed over blasted areas 100mm away from unblasted areas or
within 100mm of edges prepared for field welds.
3.3.6
The first coat of paint (primer coat) will be applied as soon as possible after surface
preparation.
3.3.7
Each coat of paint will be allowed to dry thoroughly in accordance with the paint
manufacturers over coating instructions/recommendations before the next coat is applied.
All coating material will be applied evenly in normal full coat free from sagging, pinhole,
orange peeling.
3.3.8
Wet film thickness and dry film thickness will be checked during and after application of
each coat to ensure that total DFT as specified will be achieved. These data shall be
property recorded on report.
3.3.9
Checking of the temperature, humidity and dew point shall be done twice a day minimum
and particularly every morning before starting of blasting and coating application.
All hard to spray areas, corners, edges and welds will be brush painted with same paint
and film thickness before application of each coat.
Any defect, mechanical damage that may occur will be repaired before the application of
further coats.
-
Remove all visible oil, grease spots and other contaminant by solvent cleaning.
All damage areas will be either blast cleaned to Sa 2.5 (ISO 8501-1:1988) or power
tool cleaned to St 3 (ISO 8501-1-1988) depending on the surface concerned and extent
of the damage.
Brush clean the affected area to remove al dirt, dust and other contaminant from the
surface.
Re-apply the coating system on the affected area to the required film thickness.
3.4
Phasing/sequence:
The planning will be adapted such a way that surface preparation and primer application of
sub- assemblies will be performed in enclosed blasting chambers/painting workshop prior
to assemble them on site.
1 X 60 mic DFT
- Finish:
Polyurethane
HEMPATHANE TC 55210
1 X 50mic DFT
4.2
1 X 50 mic DFT
epoxy primer
- Finish:
3 X 150mic DFT
4.3
- Finish:
4.4
Notes:
-
The top of Buoy body shall be coated as per system No.1 with the addition of Antislip aggregate (HEMPELS ANTI-SLINT 67500) prior applying the topcoat.
Wherever several coats of the same product need to be applied as per specified coating
system, different color shades will be used to clearly identify each of the coat (see
attached paint manufacturers specification for details).
(*) For external Coating Systems No. 1 & 2, we are considering optionally to make the
surface preparation simultaneously with the internal surfaces, but not to apply the
primer coat just after. We would then sweep blast the entire external surfaces after
complete assembly and welding works of the Buoy Body on one side and on the
rotating part on another side.
-
(**) In case we validate the above option, we would cancel the primer coat specified
for the Coating System No. 2 and apply directly the first coat of HEMPADUR
MASTIC 45881 over the prepared steel substrate.
Dry film thickness for each application (after application, prior subsequent coats)
Adherence test (pull-off test). These destructive tests will be conducted on separate
reference plates (size & quantity to be commonly agreed with SBM and paint supplier.
These reference plates will be prepared and coated during the production, in all
respects in the same conditions and in the same time than a reference surface area on
the buoy.
Visual aspect of the coating (inclusion, micro porositys runs, sag. etc)
Testing and inspection will be carried out in accordance with the governing relevant
Specification.
All test records will be issued for review and approval by SBM and paint suppliers
Supervisor.
The paint manufacturers TSR will be countersign the record, and will determine
extend of follow-up
7- SAFETY:
-
Safety precautions related to material (paints & thinners...) are clearly described on the
Technical Data Sheets and Material Safety Data Sheets.
Painting location will be protected to prevent painting dust going to building structure,
cladding and surrounding environment, as well as over-spray on adjacent surface
already coated.
8- INSURANCE/GUARRANTEE:
9- ATTACHMENTS:
APPLICATION INSTRUCTIONS
INDUSTRIAL SERVICES
OFFSHORE SERVICES
MARINE SERVICES
Mechanical, Electrical, Piping, Steel Structure , Pressure Vessel Fabrication & Installation.
Oil & Gas Engineering, Offshore Constructions & Maintenance.
Ship Construction, Ship Repair.
SF 10-01 HQ 55
Specification sheet
HEMPEL A/S
Customer:
SAIGON SHIPYARD Co., Ltd
Project:
Area:
1. EMERGED ZONE
Surface preparation:
Oil and grease etc. to be removed by emulsion cleaning. Entire area to be (high
pressure) fresh water cleaned in order to remove salts and other contaminants. When
the surface is dry: Abrasive blasting to minimum Sa 2 according to ISO 8501-1:1988
with a surface profile corresponding to Rugotest No. 3 BN 9a.
Treated area
%
f/c
f/c
f/c
f/c
f/c: full coat
Film thickness
(micron)
Wet
Dry
Shade no.
Shade
Red-grey
Red
Grey
Yellow
Total d.f.t.
Hrs=Hour(s)
19830
50630
11480
27186
Mth=Month(s)
100
200
200
100
60
150
150
50
410
11.0
5.1
5.1
10.4
Recommended
Nozzle
orifice
X
X
.017"-.021"
(X)
X
.017"-.023"
(X)
X
.017"-.023"
(X)
(X)
X
.017"-.019"
X: Recommended (X): Possible
Nozzle
pressure
175 bar
250 bar
250 bar
150 bar
N/R=Not Recommended
D.F.T.
Quality no
17340
45881
45881
(micron)
60
150
150
45881
45881
55210
40C
Min.
30C
Max.
N/R
N/R
3 Hrs
None
3 Hrs 10 Day
Min.
20C
Max.
4 Hrs 22 Day
4 Hrs
None
4 Hrs 15 Day
Min.
5 Hrs
5 Hrs
5 Hrs
10C
Max.
30 Day
None
21 Day
Min.
N/R
N/R
N/R
0C
Max.
N/R
N/R
N/R
Min.
N/R
N/R
N/R
-10C
Max.
N/R
N/R
N/R
Min.
N/R
N/R
N/R
Max.
N/R
N/R
N/R
User name:
Department name:
SGPVH0206 Page:
Quality Code:
Environment :
Medium
HEMPEL
SF 10-01 HQ 55
Specification sheet
HEMPEL A/S
Customer:
SAIGON SHIPYARD Co., Ltd
Project:
Area:
1. EMERGED ZONE
Remarks:
1. All welding seams, spatters, burrs, edges, corner, etc... must be gound up to smooth surface before paint application.
2. Paint only is applied on the clean and dry surface with substrate temperature at least 3oC higher than dew point and relative humidity (RH) of max. 85%.
3. Touching up for each coat by brush with product as same as initially applied must be carried out at low dft areas such as corner, edges, cut out, scalop, areas difficult for
spraying, etc...in order to ensure to achieve the min specified DFT as per paint specification.
4. All mechical damaged, welding and burning areas must be repaired by mechanical cleaning to min St.3, preferably spot blasting to Sa2.5 in accordance with ISO 8501-1988,
feathering edges down to sound and intact layer, dust off residues and followed by re-applying coating system on affected areas to required film thickness.
5. In case of max. recoating interval exceeded, roughening entire surface by sanding down with sandpaper, grinding by disksander or by abrasive sweeping before application of
subsequent coat in order to ensure a good intercoat adhesion
6.If the primer (Hempadur Zinc 17340) is exposed to the outside weather for too long time, a special attention should be paid to remove completely zinc salt built up over time on the
surface by sanding down with sandpaper and followed by fresh water hosing before nexth coat application.
7.Anti-skid particles - Hempel's Anti-slint 67500 shall be used with rate of 1kg per every 10 sqm on the surface required for anti-skidding properties. It should be sprinkled directly on
the fresh undercoat and then covered by application of topcoat to secure firmly adhesion.
8. Pls see product datasheet and application instruction for more details.
Product information:
Volume
solids %
66
77
77
52
Shade no.
19830
50630
11480
27186
Curing
agent
97040
95881
95881
95370
Mixing ratio
volume
4:1
3:1
3:1
7:1
Pot life
Dry to touch
20C
2h
3h
3h
4h
20C
3h
6h
6h
8h
Flash
point
C
24
35
35
33
Thinner
08450
08450
08450
08080
Application restrictions
Min.
Max. RH%
C
-10
15
15
-10
Data, specifications, directions and recommendations given in this painting specification represent test results or experience obtained under controlled or specially defined circumstances. Their accuracy, completeness or appropriateness
under the actual conditions of the intended use is not guaranteed and must be determined by User. Manufacturer and Seller assume no liability in excess of what is stated in our GENERAL CONDITIONS OF SALE, DELIVERY AND SERVICE
for results obtained, injury, direct or consequential damage incurred from the use as recommended above, overleaf, or otherwise.
Hempel's PreSale System 2.6.16 (Build 633)
Printed at:
09-10-2007 10:39
Created/Last modified:
09-10-2007 10:17
User name:
Department name:
SGPVH0206 Page:
Quality Code:
Environment :
Medium
HEMPEL
SF 10-01 HQ 55
Specification sheet
HEMPEL A/S
Customer:
SAIGON SHIPYARD Co., Ltd
Project:
Area:
2. SUBMERGED ZONE
Surface preparation:
Oil and grease etc. to be removed by emulsion cleaning. Entire area to be (high
pressure) fresh water cleaned in order to remove salts and other contaminants. When
the surface is dry: Abrasive blasting to minimum Sa 2 according to ISO 8501-1:1988
with a surface profile corresponding to Rugotest No. 3 BN 9a.
Treated area
%
HEMPADUR 15590
HEMPADUR MASTIC 45881
HEMPADUR MASTIC 45881
HEMPADUR MASTIC 45881
t/u: touch up
f/c
f/c
f/c
f/c
f/c: full coat
Film thickness
(micron)
Wet
Dry
Shade no.
Shade
Red brown
Grey
Red
Black
Total d.f.t.
Hrs=Hour(s)
56880
11480
50630
19990
Mth=Month(s)
125
200
200
200
50
150
150
150
500
8.8
5.1
5.1
5.1
Recommended
Nozzle
orifice
(X)
X
.017"-.019"
(X)
X
.017"-.023"
(X)
X
.017"-.023"
(X)
X
.017"-.023"
X: Recommended (X): Possible
Nozzle
pressure
150 bar
250 bar
250 bar
250 bar
N/R=Not Recommended
D.F.T.
Quality no
15590
45881
45881
(micron)
50
150
150
45881
45881
45881
40C
Min.
4 Hrs
5 Hrs
5 Hrs
30C
Max.
12 Day
15 Day
15 Day
Min.
20C
Max.
7 Hrs 20 Day
7 Hrs 22 Day
7 Hrs 22 Day
Min.
11 Hrs
8 Hrs
8 Hrs
10C
Max.
30 Day
30 Day
30 Day
Min.
N/R
N/R
N/R
0C
Max.
N/R
N/R
N/R
Min.
N/R
N/R
N/R
-10C
Max.
N/R
N/R
N/R
Min.
N/R
N/R
N/R
Max.
N/R
N/R
N/R
User name:
Department name:
SGPVH0206 Page:
Quality Code:
Environment :
Immersion
HEMPEL
SF 10-01 HQ 55
Specification sheet
HEMPEL A/S
Customer:
SAIGON SHIPYARD Co., Ltd
Project:
Area:
2. SUBMERGED ZONE
Remarks:
1. All welding seams, spatters, burrs, edges, corner, etc... must be gound up to smooth surface before paint application.
2. Paint only is applied on the clean and dry surface with substrate temperature at least 3oC higher than dew point and relative humidity (RH) of max. 85%.
3. Touching up for each coat by brush with product as same as initially applied must be carried out at low dft areas such as corner, edges, cut out, scalop, areas difficult for
spraying, etc...in order to ensure to achieve the min specified DFT as per paint specification.
4. All mechical damaged, welding and burning areas must be repaired by mechanical cleaning to min St.3, preferably spot blasting to Sa2.5 in accordance with ISO 8501-1988,
feathering edges down to sound and intact layer, dust off residues and followed by re-applying coating system on affected areas to required film thickness.
5. In case of max. recoating interval exceeded, roughening entire surface by sanding down with sandpaper, ginding by disksander or by abrasive sweeping before application of
subsequent coat in order to ensure a good intercoat adhesion
6. Pls see product datasheet and application instruction for more details.
Product information:
HEMPADUR 15590
HEMPADUR MASTIC 45881
HEMPADUR MASTIC 45881
HEMPADUR MASTIC 45881
Shade no.
56880
11480
50630
19990
Volume
solids %
44
Curing
agent
95100
77
77
77
95881
95881
95881
Mixing ratio
volume
Pot life
Dry to touch
20C
3h
Flash
point
C
26
15 : 4
20C
2h
Thinner
08450
3:1
3:1
3:1
3h
3h
3h
6h
6h
6h
35
35
35
08450
08450
08450
Application restrictions
Min.
Max. RH%
C
5
80
15
15
15
Data, specifications, directions and recommendations given in this painting specification represent test results or experience obtained under controlled or specially defined circumstances. Their accuracy, completeness or appropriateness
under the actual conditions of the intended use is not guaranteed and must be determined by User. Manufacturer and Seller assume no liability in excess of what is stated in our GENERAL CONDITIONS OF SALE, DELIVERY AND SERVICE
for results obtained, injury, direct or consequential damage incurred from the use as recommended above, overleaf, or otherwise.
Hempel's PreSale System 2.6.16 (Build 633)
Printed at:
09-10-2007 10:39
Created/Last modified:
09-10-2007 10:17
User name:
Department name:
SGPVH0206 Page:
Quality Code:
Environment :
Immersion
HEMPEL
SF 10-01 HQ 55
Specification sheet
HEMPEL A/S
Customer:
SAIGON SHIPYARD Co., Ltd
Project:
Area:
3. INSIDE BOY COMPARTMENT
Surface preparation:
Oil and grease etc. to be removed by emulsion cleaning. Entire area to be (high
pressure) fresh water cleaned in order to remove salts and other contaminants. When
the surface is dry: Abrasive blasting to minimum Sa 2 according to ISO 8501-1:1988.
Treated area
%
f/c
f/c
f/c: full coat
Film thickness
(micron)
Wet
Dry
Shade no.
Shade
Red
White
Total d.f.t.
Hrs=Hour(s)
50630
10000
Mth=Month(s)
175
175
125
125
250
6.2
6.2
Recommended
Nozzle
orifice
Nozzle
pressure
(X)
X
.017"-.023" 250 bar
(X)
X
.017"-.023" 250 bar
X: Recommended (X): Possible
N/R=Not Recommended
D.F.T.
Quality no
45881
(micron)
125
45881
40C
Min.
3 Hrs
30C
Max.
None
Min.
5 Hrs
20C
Max.
None
Min.
6 Hrs
10C
Max.
None
Min.
N/R
0C
Max.
N/R
Min.
N/R
Max.
N/R
-10C
Min.
Max.
N/R
N/R
User name:
Department name:
SGPVH0206 Page:
Quality Code:
Environment :
Severe
HEMPEL
SF 10-01 HQ 55
Specification sheet
HEMPEL A/S
Customer:
SAIGON SHIPYARD Co., Ltd
Project:
Area:
3. INSIDE BOY COMPARTMENT
Remarks:
1. All welding seams, spatters, burrs, edges, corner, etc... must be gound up to smooth surface before paint application.
2. Paint only is applied on the clean and dry surface with substrate temperature at least 3oC higher than dew point and relative humidity (RH) of max. 85%.
3. Touching up for each coat by brush with product as same as initially applied must be carried out at low dft areas such as corner, edges, cut out, scalop, areas difficult for
spraying, etc...in order to ensure to achieve the min specified DFT as per paint specification.
4. All mechical damaged, welding and burning areas must be repaired by mechanical cleaning to min St.3, preferably spot blasting to Sa2.5 in accordance with ISO 8501-1988,
feathering edges down to sound and intact layer, dust off residues and followed by re-applying coating system on affected areas to required film thickness.
5. In case of max. recoating interval exceeded, roughening entire surface by sanding down with sandpaper, ginding by disksander or by abrasive sweeping before application of
subsequent coat in order to ensure a good intercoat adhesion
6. Pls see product datasheet and application instruction for more details.
Product information:
Shade no.
50630
10000
Volume
solids %
77
Curing
agent
95881
77
95881
Mixing ratio
volume
Pot life
Dry to touch
20C
6h
Flash
point
C
35
3:1
20C
3h
Thinner
08450
3:1
3h
6h
35
08450
Application restrictions
Min.
Max. RH%
C
15
15
Data, specifications, directions and recommendations given in this painting specification represent test results or experience obtained under controlled or specially defined circumstances. Their accuracy, completeness or appropriateness
under the actual conditions of the intended use is not guaranteed and must be determined by User. Manufacturer and Seller assume no liability in excess of what is stated in our GENERAL CONDITIONS OF SALE, DELIVERY AND SERVICE
for results obtained, injury, direct or consequential damage incurred from the use as recommended above, overleaf, or otherwise.
Hempel's PreSale System 2.6.16 (Build 633)
Printed at:
09-10-2007 10:39
Created/Last modified:
09-10-2007 10:17
User name:
Department name:
SGPVH0206 Page:
Quality Code:
Environment :
Severe
HEMPEL
SF 10-01 HQ 55
Specification sheet
HEMPEL A/S
Customer:
SAIGON SHIPYARD Co., Ltd
Project:
Area:
4. INSIDE TURNTABLE & BALLAST BOX
Surface preparation:
Oil and grease etc. to be removed by emulsion cleaning. Entire area to be (high
pressure) fresh water cleaned in order to remove salts and other contaminants. When
the surface is dry: Abrasive blasting to minimum Sa 2 according to ISO 8501-1:1988.
Treated area
%
f/c
f/c: full coat
Shade no.
Shade
White
Total d.f.t.
10000
Film thickness
(micron)
Wet
Dry
125
100
100
7.7
Recommended
Nozzle
orifice
Nozzle
pressure
(X)
X
.017"-.023" 250 bar
X: Recommended (X): Possible
User name:
Department name:
SGPVH0206 Page:
Quality Code:
Environment :
Severe
HEMPEL
SF 10-01 HQ 55
Specification sheet
HEMPEL A/S
Customer:
SAIGON SHIPYARD Co., Ltd
Project:
Area:
4. INSIDE TURNTABLE & BALLAST BOX
Remarks:
1. All welding seams, spatters, burrs, edges, corner, etc... must be gound up to smooth surface before paint application.
2. Paint only is applied on the clean and dry surface with substrate temperature at least 3oC higher than dew point and relative humidity (RH) of max. 85%.
3. Touching up for each coat by brush with product as same as initially applied must be carried out at low dft areas such as corner, edges, cut out, scalop, areas difficult for
spraying, etc...in order to ensure to achieve the min specified DFT as per paint specification.
4. All mechical damaged, welding and burning areas must be repaired by mechanical cleaning to min St.3, preferably spot blasting to Sa2.5 in accordance with ISO 8501-1988,
feathering edges down to sound and intact layer, dust off residues and followed by re-applying coating system on affected areas to required film thickness.
5. Pls see product datasheet and application instruction for more details.
Product information:
Volume
solids %
77
Shade no.
10000
Curing
agent
95881
Mixing ratio
volume
3:1
Pot life
Dry to touch
20C
3h
20C
6h
Flash
point
C
35
Thinner
08450
Application restrictions
Min.
Max. RH%
C
15
Data, specifications, directions and recommendations given in this painting specification represent test results or experience obtained under controlled or specially defined circumstances. Their accuracy, completeness or appropriateness
under the actual conditions of the intended use is not guaranteed and must be determined by User. Manufacturer and Seller assume no liability in excess of what is stated in our GENERAL CONDITIONS OF SALE, DELIVERY AND SERVICE
for results obtained, injury, direct or consequential damage incurred from the use as recommended above, overleaf, or otherwise.
Hempel's PreSale System 2.6.16 (Build 633)
Printed at:
09-10-2007 10:39
Created/Last modified:
09-10-2007 10:17
User name:
Department name:
SGPVH0206 Page:
Quality Code:
Environment :
Severe
HEMPEL
INDUSTRIAL SERVICES
OFFSHORE SERVICES
MARINE SERVICES
Mechanical, Electrical, Piping, Steel Structure , Pressure Vessel Fabrication & Installation.
Oil & Gas Engineering, Offshore Constructions & Maintenance.
Ship Construction, Ship Repair.
Product Data
HEMPADURZINC 17340
BASE 17349 with CURING AGENT 97040
Description:
HEMPADUR ZINC 17340 is a two-component zinc rich epoxy paint. It cures to a strong
and corrosion resistant coating.
Recommended use:
1.
2.
Availability:
PHYSICAL CONSTANTS:
Colours/Shade nos:
Finish:
Volume solids, %:
Theoretical spreading rate:
Flash point:
Specific gravity:
Surface dry:
Dry to touch:
Fully cured:
V.O.C.:
Red-grey/198300
Semi-flat
66 1
13.2 m/litre - 50 micron
529 sq.ft./US gallon - 2 mils
24C/75F
2.3 kg/litre - 19.2 lbs/US gallon
2 (approx.) hrs at 20C/68F (ISO 1517)
3 (approx.) hours at 20C/68F
7 days at 20C/68F
325 g/litre - 2.7 lbs/US gallon
The physical constants stated are nominal data according to the HEMPEL Group's approved formulas. They are
subject to normal manufacturing tolerances and where stated, being standard deviation according to ISO 3534-1.
APPLICATION DETAILS:
Mixing ratio for 17340:
Application method:
Thinner (max.vol.):
Pot life:
Nozzle orifice:
Nozzle pressure:
Cleaning of tools:
Indicated film thickness, dry:
Indicated film thickness, wet:
Recoat interval, min:
Recoat interval, max:
Safety:
Page 1 of 2
HEMPEL
Product Data Sheet
New steel: Remove oil and grease, etc. with suitable detergent. Remove salt and other
contaminants by (high pressure) fresh water cleaning. Abrasive blasting to Sa 2.
For temporary protection, if required, use suitable zinc shopprimer. All damage of shopprimer and
contamination from storage and fabrication should be thoroughly cleaned prior to final painting. For
repair and touch-up use HEMPADUR ZINC 17340.
Maintenance: Remove oil and grease etc. with suitable detergent. Remove salt and other
contaminants by (high pressure) fresh water cleaning. Remove all rust and loose material
preferably by dry abrasive blasting. Minor areas may be power tool cleaned.
APPLICATION :
CONDITIONS
Use only where application and curing can proceed at temperatures above -10C/14F.
At the freezing point and below be aware of ice on the surface, which will hinder the adhesion.
The temperature of the paint itself should be 15C/60F or above to secure proper application
properties. In confined spaces provide adequate ventilation during application and drying.
Apply only on a dry and clean surface with a temperature above the dew point to avoid
condensation.
SUBSEQUENT
COAT:
According to specification.
REMARKS:
Note: If used as anticorrosive protection under insulation of high temperature equipment it is very
important that NO moisture can penetrate during slow-down periods. This to avoid risk of "wet
corrosion" when the temperature rises.
May be specified in another film thickness than indicated depending on purpose and area of use.
This will alter spreading rate and may influence drying time and recoating interval. Normal range is
50-75 micron/2-3 mils.
(The dry film thickness range does not take into account the correction factors for rough surfaces
as listed in ISO 19840).
Recoating intervals, 50 micron/1 mil dry film thickness for HEMPADUR ZINC 17340:
Recoating:
Surface temperature
Recoated with
(Quality numbers only)
Minimum
Maximum
20C/68F
20C/68F
Atmospheric
Atmospheric
As a
container
coating
As a general
protective
coating
8 hours
1 hour
30 minutes
58030
5 hours
1 hour
30 minutes
46410. 46370
30 days*
4 hours
30 minutes
HEMPADUR
3 days
Not relevant
30 minutes
HEMPATHANE
* If the coating has been subjected to direct sunlight for a short period only, the maximum recoating interval may be
prolonged.
Note:
Before recoating after exposure in contaminated environment, clean the surface thoroughly by
(high pressure) fresh water hosing and allow to dry.
If the maximum recoating interval is exceeded, roughening of the surface is necessary to ensure
intercoat adhesion.
A completely clean surface is mandatory to ensure intercoat adhesion, especially at long recoating
intervals. Any dirt, oil, grease, and other foreign matter must be removed with suitable detergent
followed by (high pressure) fresh water cleaning. In addition, scrubbing with a stiff brush may be
necessary to remove zinc corrosion products (white rust).
HEMPADUR ZINC 17340 is for professional use only.
ISSUED BY:
This
Product Data
Data Sheet
Sheet supersedes
supersedes those
This Product
thosepreviously
previouslyissued.
issued.
For
explanations, definitions
For explanations,
definitionsand
andscope,
scope,see
seeExplanatory
ExplanatoryNotes
Notesininthe
theHEMPEL
HEMPELBook.
Book.
Data,
specifications,
directions
and
recommendations
given
represent
only
test
results
or or
Data, specifications, directions and recommendations givenininthis
thisdata
datasheet
sheet
represent
only
test
results
experience
obtained
under
controlled
or
specially
defined
circumstances.
Their
accuracy,
completeness
or or
experience obtained under controlled or specially defined circumstances. Their accuracy,
completeness
appropriateness
ofof
the
Products
herein
must
bebe
determined
appropriatenessunder
underthe
theactual
actualconditions
conditionsofofany
anyintended
intendeduse
use
the
Products
herein
must
determined
exclusively
the Buyer
Buyer and/or
and/or User.
exclusively by
by the
User.
The
Products are
are supplied
toto
HEMPEL's
OF
The Products
supplied and
and all
alltechnical
technicalassistance
assistanceisisgiven
givensubject
subject
HEMPEL'sGENERAL
GENERALCONDITIONS
CONDITIONS OF
SALES,
DELIVERYAND
ANDSERVICE,
SERVICE,
unless
otherwise
expresslyagreed
agreedininwriting.
writing.The
The
Manufacturerand
andSeller
Seller
SALES, DELIVERY
unless
otherwise
expressly
Manufacturer
disclaim, and
disclaim,
and Buyer
Buyer and/or
and/orUser
Userwaive
waive all
allclaims
claimsinvolving,
involving,any
anyliability,
liability,including
includingbut
butnot
notlimited
limitedtotonegligence,
negligence,
except as
forall
all results,
results, injury
injury or
or direct
direct or
or consequential
consequential losses
except
as expressed
expressed in
in said
saidGENERAL
GENERAL CONDITIONS
CONDITIONS for
lossesor
or
damages
arising
from
the
use
of
the
Products
as
recommended
above,
on
the
overleaf
or
otherwise.
damages arising from the use of the Products as recommended above, on the overleaf or otherwise.
Product data are subject to change without notice and become void five years from the date of issue.
Page 2 of 2
HEMPEL
Product
Data
Page 1/2
HEMPADUR15590
BASE 15599 with CURING AGENT 95100
Description:
Recommended use:
Service temperatures:
Availability:
PHYSICAL CONSTANTS:
Colours/Shade nos:
Finish:
Volume solids, %:
Theoretical spreading rate:
Flash point:
Specific gravity:
Dry to touch:
Fully cured:
V.O.C.:
Red/56880
Semi-gloss
44 1
11.0 m/litre - 40 micron
441 sq.ft./US gallon - 1.6 mils
26C/79F
1.3 kg/litre - 10.8 lbs/US gallon
3 (approx.) hours at 20C/68F
7 days at 20C/68F
500 g/litre - 4.2 lbs/US gallon
The physical constants stated are nominal data according to the HEMPEL Group's approved formulas. They are subject
to normal manufacturing tolerances and where stated, being standard deviation according to ISO 3534-1.
Further reference is made to "Explanatory Notes" in the HEMPEL Book.
APPLICATION DETAILS:
Mixing ratio:
Application method:
Thinner (max.vol.):
Pot life:
Nozzle orifice:
Nozzle pressure:
Cleaning of tools:
Indicated film thickness, dry:
Indicated film thickness, wet:
Recoat interval, min:
Recoat interval, max:
Safety:
Issued:
Handle with care. Before and during use, observe all safety labels on packaging and
paint containers, consult HEMPEL Material Safety Data Sheets and follow all local or
national safety regulations. Avoid inhalation, avoid contact with skin and eyes, and do
not swallow. Take precautions against possible risks of fire or explosions as well as
protection of the environment. Apply only in well ventilated areas.
April 2003
HEMPEL
Page 2/2
HEMPADUR 15590
SURFACE
PREPARATION:
New steel: Abrasive blasting to Sa 2-3 depending on area of use. Minimum surface profile
corresponding to Rugotest No. 3, BN11a, Keane-Tator Comparator, 5.5 G/S, or ISO Comparator
Coarse (G) - or as per the specification for the subsequent coat(s). Oil and grease must be
removed with suitable detergent, salts and other contaminants by (high pressure) fresh water
cleaning prior to blasting. After blasting, clean the surface carefully from abrasives and dust.
Maintenance: On old steel surfaces having been exposed to salt water, excessive amounts of salt
residues in pittings may call for wet abrasive blasting followed by dry abrasive blasting.
Alternatively, dry abrasive blasting followed by high pressure fresh water cleaning, drying, and
finally, dry abrasive blasting again.
APPLICATION
CONDITIONS:
Apply only to a dry and clean surface with a temperature above the dew point to avoid
condensation. Minimum temperature for application is 5C/41F, preferably above 10C/50F.
Relative humidity maximum 80%, preferably below 60%.
The temperature of the paint itself should preferably be between 15C/59F and 25C/77F.
In confined spaces provide adequate ventilation during application and drying.
PRECEDING
COAT:
None.
SUBSEQUENT
COAT:
REMARKS:
Film thicknesses:
The coating has been applied in a dry film thickness as near as possible to the specified 40
micron.
The film formation has been of good quality and without any dry spray.
The drying and curing conditions have been according to APPLICATION CONDITIONS, please
see above. (In the case of long recoating intervals: until full curing has been obtained).
No kind of surface contamination exists, except loose dust, etc. which is possible to remove by
vacuum cleaning (tanks) / hosing down (exterior).
The surface MUST be completely clean before recoating. The coating is checked carefully and
should be without patchy, whitish, and/or greasy formations, which can hinder adhesion of
subsequent coat. Note: Exudation of curing agent causes the mentioned patchy, whitish,
and/or greasy formations which will take place if HEMPADUR 15590 is applied at low
temperature without proper induction time and/or if the coating is exposed to water (rain,
condensation) during drying and curing.
Depending on actual local conditions, extended maximum recoating intervals may apply. Please
contact HEMPEL for further advice.
If the maximum recoating interval is exceeded, roughening of the surface is necessary to ensure
intercoat adhesion. Before recoating after exposure in contaminated environment, clean surface
thoroughly by (high pressure) fresh water hosing and allow to dry. HEMPADUR 15590 will resist a
hosing down of the surface 8 hours after application at a steel temperature of 20C/68F.
Note:
ISSUED:
This Product Data Sheet supersedes those previously issued. For definition and scope, see explanatory notes to
applicable Product Data Sheets.
Data, specifications, directions and recommendations given in this data sheet represent only test results or experience
obtained under controlled or specially defined circumstances. Their accuracy, completeness or appropriateness under
the actual conditions of any intended use of the Products herein must be determined exclusively by the Buyer and/or
User. The Products are supplied and all technical assistance is given subject to HEMPEL's GENERAL CONDITIONS OF
SALES, DELIVERY AND SERVICE, unless otherwise expressly agreed in writing. The Manufacturer and Seller disclaim,
and Buyer and/or User waive all claims involving, any liability, including but not limited to negligence, except as
expressed in said GENERAL CONDITIONS for all results, injury or direct or consequential losses or damages arising
from the use of the Products as recommended above, on the overleaf or otherwise.
Product data are subject to change without notice and become void five years from the date of issue.
Product Data
1/2
HEMPELS
THINNER NO.
FLASH POINT
08080
25C/77F
EXAMPLES OF
GENERAL USE
HEMPELS ANTIFOULINGS
GLOBIC, OCEANIC and OLYMPIC
HEMPALIN DECKPAINT 53240.
HEMPAQUICK qualities
All-purpose thinner for HEMPATEX qualities.
HEMPATHANE topcoats and enamels.
08230
32C/90F
08450
23C/73F
08510
3C/37F
HIGHLY
FLAMMABLE
08570
4C/39F
Page 1 of 2
HEMPEL
Product Data Sheet
2/2
REMARKS:
HEMPELS
THINNER NO.
FLASH POINT
08700
24C/75F
EXAMPLES OF
GENERAL USE
HEMPELS GALVOSILs
For HEMPADURs used as non-popping sealers
on GALVOSILs.
THINNER 08230 has a stronger thinning effect than white spirit or turpentine.
Tools can usually be cleaned with the THINNER prescribed for the product.
Note:
For cleaning of tools which have been used for HEMPADUR products, HEMPELS TOOL CLEANER
99610 is recommended. Do not use it for thinning, nor for cleaning after use of polyurethane
products, HEMPATHANEs.
HEMPEL'S THINNERS are for professional use only.
Safety:
Handle with care. Before and during use, observe all safety labels on packaging and paint
containers, consult HEMPEL Material Safety Data Sheets and follow all local or national safety
regulations. Avoid inhalation, avoid contact with skin and eyes, and do not swallow. Take
precautions against possible risks of fire or explosions as well as protection of the environment.
Apply only in well ventilated areas.
ISSUED BY:
HEMPEL A/S
0808000000CO004
0823000000CO005
0845000000CO009
0851000000CO002
0857000000CO007
0870000000CO006
Page 2 of 2
Product Data
HEMPADURMASTIC 45880/
HEMPADURMASTIC 45881
High temperatures: 45881: BASE 45889 with CURING AGENT 95881
Low to medium temperatures: 45880: BASE 45889 with CURING AGENT 95880
Description:
Recommended use:
Service temperatures:
Certificates/Approvals:
Availability:
PHYSICAL CONSTANTS:
Version, mixed product:
Colours/Shade nos:
Finish:
Volume solids, %:
Theoretical spreading rate:
Flash point:
Specific gravity:
Dry to touch:
Fully cured:
V.O.C.:
45880
45881
Grey/12170*
Grey/12170*
Semi--gloss
Semi--gloss
77 1
77 1
3.9 m/litre - 200 micron
3.9 m/litre - 200 micron
154 sq.ft./US gallon - 8 mils
154 sq.ft./US gallon - 8 mils
35C/95F
35C/95F
1.4 kg/litre - 11.7 lbs/US gallon
1.4 kg/litre - 11.7 lbs/US gallon
4 (approx) hours at 20C/68F
3 (approx) hours at 30C/86F
7 days at 20C/68F
5 days at 30C/86F
220 g/litre - 1.8 lbs/US gallon
220 g/litre - 1.8 lbs/US gallon
*Other shades including a MIO version, colour no. 12430, according to assortment list.
The physical constants stated are nominal data according to the HEMPEL Group's approved formulas. They are
subject to normal manufacturing tolerances and where stated, being standard deviation according to ISO 3534-1.
APPLICATION DETAILS:
Version:
Mixing ratio:
Application method:
Thinner (max. vol.):
Pot life:
Nozzle orifice:
Nozzle pressure:
Cleaning of tools:
Indicated film thickness, dry:
Indicated film thickness, wet:
Recoat interval, min/max:
Safety:
45880
45881
Base 45889 : Curing agent 95880
Base 45889 : Curing agent 95881
3 : 1 by volume
3 : 1 by volume
Airless spray
Brush (touch up)
Airless spray
Brush (touch up)
Depending on purpose usually less than 5% THINNER 08450 (See REMARKS overleaf)
1 hour (20C/68F) (Airless spray)
1 hour (30C/86F) (Airless spray)
2 hours (20C/68F) (Brush)
2 hours (30C/86F) (Brush)
.017"-.023" (See separate APPLICATION INSTRUCTIONS)
250 bar/3600 psi (Airless spray data are indicative and subject to adjustment)
HEMPELS TOOL CLEANER 99610 or HEMPEL'S THINNER 08450
200 micron/8 mils (see REMARKS overleaf)
275 micron/11 mils
According to separate APPLICATION INSTRUCTIONS
Handle with care. Before and during use, observe all safety labels on packaging and paint
containers, consult HEMPEL Material Safety Data Sheets and follow all local or national safety
regulations. Avoid inhalation, avoid contact with skin and eyes, and do not swallow. Take
precautions against possible risks of fire or explosions as well as protection of the environment.
Apply only in well ventilated areas
Page 1 of 2
HEMPEL
Product Data Sheet
APPLICATION
CONDITIONS:
New steel: When used as an intermediate or finishing coat please refer to the data sheet for the
preceding GALVOSIL or HEMPADUR primer. When used as a primer please refer to the
specification.
Zinc silicate painted or spray-metallized surfaces: Remove oil and grease, etc. with suitable
detergent. Remove salt and other contaminants by (high pressure) fresh water cleaning. Zinc salts
(white rust) must be removed by high pressure hosing combined with rubbing with a stiff nylon
brush if necessary. It is recommended to recoat spray-metallized surfaces as soon as possible to
avoid possible contamination.
Concrete: Remove slip agent and other possible contaminants by emulsion washing followed by
high pressure hosing with fresh water. Remove scum layer and loose matter to a hard, rough and
uniform surface, preferably by abrasive blasting, possibly by other mechanical treatment or acid
etching. Seal surface with suitable sealer, as per relevant painting specification.
Repair and maintenance: Remove oil and grease, etc. with suitable detergent. Remove salt and
other contaminants by (high pressure) fresh water cleaning. Clean damaged areas thoroughly by
power tool cleaning to minimum St 2 (spot-repairs) or by abrasive blasting to min. Sa 2, preferably
to Sa 2. Improved surface preparation will improve the performance of HEMPADUR MASTIC
45880/45881. As an alternative to dry cleaning, water jetting to min. WJ-2 (NACE No. 5/SSPC-SP
12)(or according to specification), may be used. A flash-rust degree of maximum FR-2 (Hempel
standard) is acceptable before application. Feather edges to sound and intact paint. Dust off
residues.
On pit-corroded surfaces, excessive amounts of salt residues may call for water jetting, wet
abrasive blasting, alternatively dry abrasive blasting, high pressure fresh water hosing, drying, and
finally, dry abrasive blasting again.
Apply only on a dry and clean surface with a temperature above the dew point to avoid
condensation. Use only when application and curing can proceed at temperatures above -5C/23F
(recommended lowest temperature is 0C/32F) for HEMPADUR MASTIC 45880 and above approx
15C/59F for HEMPADUR MASTIC 45881. The temperature of the paint itself should be
15C/59F or above, but advantageously below approximately 30C/86F to secure proper
application properties. Optimal spraying properties are obtained at a paint temperature of 1822C/64-72F. In warmer climates, the paint should be stored in a cool place and the paint
temperature should preferably be kept below 30C/86F. In confined spaces provide adequate
ventilation during application and drying. In cases where faster drying at very low temperatures is
required, HEMPADUR MASTIC 45880 may advantageously be replaced by HEMPADUR 45143.
Please also see separate APPLICATION INSTRUCTIONS.
PRECEDING and
SUBSEQUENT COAT:
REMARKS:
Colours/Colourstability:
Page 2 of 2
Product Data
HEMPATHANETOPCOAT 55210
BASE 55219 with CURING AGENT 95370
Description:
Recommended use:
Service temperatures:
Certificates/Approvals:
Approved as a low flame spread material by Danish, French, Spanish and Singaporean
authorities according to IMO resolution MSC 61 (67).
Has a Danish, French, Spanish, Singaporean, Malaysian and Indonesian EC-type
Examination Certificate.
Please see REMARKS overleaf.
Availability:
PHYSICAL CONSTANTS:
Colours/Shade nos:
Finish:
Volume solids, %:
Theoretical spreading rate:
Flash point:
Specific gravity:
Surface dry:
Dry to touch:
Fully cured:
V.O.C.:
White/10000*
Semi-gloss
51 1
10.2 m/litre - 50 micron
409 sq.ft./US gallon - 2 mils
33C/92F
1.2 kg/litre - 10.0 lbs/US gallon
2 (approx.) hrs at 20C/68F (ISO 1517)
8 (approx.) hours at 20C/68F
7 days at 20C/68F
450 g/litre - 3.7 lbs/US gallon
Blue/30840*
Semi-gloss
51 1
10.2 m/litre - 50 micron
409 sq.ft./US gallon - 2 mils
33C/92F
1.1 kg/litre - 9.2 lbs/US gallon
2 (approx.) hrs at 20C/68F (ISO 1517)
8 (approx.) hours at 20C/68F
7 days at 20C/68F
450 g/litre - 3.7 lbs/US gallon
APPLICATION DETAILS:
Mixing ratio for 55210:
Application method:
Thinner (max. vol.):
Pot life:
Nozzle orifice:
Nozzle pressure:
Cleaning of tools:
Indicated film thickness, dry:
Indicated film thickness, wet:
Recoat interval, min:
Recoat interval, max:
Safety:
Page 1 of 2
HEMPEL
Product Data Sheet
The surface must be completely clean and dry at the time of application, and its temperature
must be above the dew point to avoid condensation. Minimum temperature for curing is
-10C/14F. At the freezing point and below, be aware of the risk of ice on the surface which will
hinder the adhesion. High humidity and/or condensation during application and the following 10
hours (20C/68F) may adversely affect the film formation.
In confined spaces provide adequate ventilation during application and drying.
PRECEDING COAT:
Service
temperatures:
Film thicknesses:
Thinning:
Electrostatic spray:
Recoating
and drying/curing
time:
Certificate has been issued under the former quality number 5521.
Certain lead-free red and yellow colours may discolour when exposed to chlorine- containing
atmosphere.
Leaded colours may become discoloured when exposed to sulphide-containing atmosphere.
To obtain full opacity, an extra coat may be necessary, especially for certain lead-free colours in eg
red, orange, yellow and green.
At service temperatures above 100C/212F, HEMPATHANE TOPCOAT 55210 will become more
soft. Furthermore, discolouration may occur.
May be specified in another film thickness than indicated depending on purpose and area of use.
This will alter spreading rate and may influence drying time and recoating interval. Normal range is
40-75 micron/1.6-3 mils.
The type and amount of thinner depend on application conditions, application method,
temperature, ventilation, and substrate. THINNER 08080 is recommended in general. THINNER
08510 may be used alternatively depending on local conditions.
Airless spray: 5-15% thinning is recommended. Under extreme conditions up to more than 20%
may be necessary to obtain satisfactory film formation.
The best result is obtained by applying a mist coat of HEMPATHANE TOPCOAT 55210 at first, and
then 2-15 minutes later apply to full film thickness giving a uniform film formation. Do not
exaggerate the film thickness.
10% thinning with specified thinner is recommended. Please contact HEMPEL for further advice.
Physical data versus temperatures:
Surface temperature
-10C/14F
0C/32F
10C/50F
20C/68F
30C/86F
3 days
36 hours
16 hours
8 hours
6 hours
(3 days)
45 hours
20 hours
10 hours
8 hours
(2 months)
32 days
14 days
7 days
5 days
Min
3 days
45 hours
20 hours
10 hours
8 hours
Max
None
None
None
None
None
Recoating interval,
recoating 55210 with 55210
*Faster drying and curing may be obtained by using an "accelerator" - consult HEMPEL for further advice.
Notes:
ISSUED BY:
Page 2 of 2
Product Data
1/1
HEMPELS ANTI-SLINT67500
Description:
HEMPELS ANTI-SLINT 67500 is flame dried silica sand of which the average particle
size is approximately 0.5 millimetre.
Recommended use:
To obtain anti-skid properties on decks and other areas where a skid-proof surface is
required.
Availability:
PHYSICAL CONSTANTS:
Colour:
Specific gravity:
Particle shape:
Greyish
2.7 (approx.) kg/litre
Grit
Remarks:
Being heavy and rather coarse HEMPELS ANTI-SLINT 67500 should not be stirred into
the paint before its application. For such purpose use HEMPEL'S ANTI-SLIP BEADS
67420.
HEMPELS ANTI-SLINT 67500 should be sprinkled evenly on the surface immediately
upon application of the penultimate coat of the paint system while the paint is still wet.
Consumption approximately 2.5 kg/5.5 lbs of HEMPELS ANTI-SLINT 67500 to 25
sq.m/ 270 sq.feet.
When the paint is dry, sweep up surplus grit and apply the final coat.
HEMPELS ANTI-SLINT 67500 should be kept dry and clean.
Do not mix contaminated sweepings with new supplies.
Note:
Safety:
Handle with care. Before and during use, observe all safety labels on packaging and
paint containers, consult HEMPEL Material Safety Data Sheets and follow all local or
national safety regulations. Avoid inhalation, avoid contact with skin and eyes, and do
not swallow. Take precautions against possible risks of fire or explosions as well as
protection of the environment. Apply only in well ventilated areas.
ISSUED BY:
HEMPEL A/S
Page 1 of 1
HEMPEL
Product Data Sheet
INDUSTRIAL SERVICES
OFFSHORE SERVICES
MARINE SERVICES
Mechanical, Electrical, Piping, Steel Structure , Pressure Vessel Fabrication & Installation.
Oil & Gas Engineering, Offshore Constructions & Maintenance.
Ship Construction, Ship Repair.
Product Type
:
:
:
:
Field of application
Date of issue
Date of Previous Issue
2.
0808000000
Hempel A/S
Lundtoftevej 150
DK-2800 Kgs. Lyngby
Denmark
Tel.: + 45 45 93 38 00
Emergency phone:
+45 45 93 38 00
See section 4 First aid
measures.
thinner
buildings and metal industry. private (yacht), ships and shipyards.
7/18/2005.
3/24/2004.
Composition/information on ingredients
Substances presenting a health or environmental hazard within the meaning of the Dangerous Substances Directive
67/548/EEC.
Ingredient Name
CAS No.
EC Number
Classification
64742-95-6
50 - 100
265-199-0
.
Notes
(*) See full text of phrases under section 16 and occupational Exposure Limit(s), if available, are listed in section 8
3.
Hazards identification
Harmful
Flammable. Harmful by inhalation. Irritating to eyes, respiratory system and skin. Harmful: may cause lung damage if
swallowed. Toxic to aquatic organisms, may cause long-term adverse effects in the aquatic environment.
4.
General
: In all cases of doubt, or when symptoms persist, seek medical attention. Never
give anything by mouth to an unconscious person.
Inhalation
: Move the person into fresh air and keep the person under surveillance. Keep person
warm and at rest. If not breathing, if breathing is irregular or if respiratory arrest
occurs, provide artificial respiration or oxygen by trained personnel. Give nothing by
mouth. If unconscious, place in recovery position and seek medical advice.
Eye Contact
: Check for and remove any contact lenses. Immediately flush eyes with plenty of
water for at least 5 minutes, occasionally lifting the upper and lower eyelids. In all
cases of doubt, or when symptoms persist, seek medical attention.
Remove contaminated clothing and shoes. Wash skin thoroughly with soap and
water or use recognized skin cleanser. Do not use solvents or thinners.
If swallowed, seek medical advice immediately and show this document. Keep
person warm and at rest. Do NOT induce vomiting unless directed to do so by
medical personnel. Lower the head so that the vomit will not reenter the mouth and
throat.
Skin Contact
Ingestion
Date of issue
: 7/18/2005.
Page: 1/4
5.
0808000000
Fire-fighting measures
Fire will produce dense black smoke. Exposure to decomposition products may cause a health hazard. Fire-fighters
should wear appropriate protective equipment. Cool closed containers exposed to fire with water. Do not release
runoff from fire to sewers or waterways.
Extinguishing Media
: Recommended: alcohol resistant foam, CO2, powders, water spray.
Not to be used : waterjet.
Fire Degradation Products
: These products are carbon oxides (CO, CO2).
6.
Exclude sources of ignition and be aware of explosion hazard. Ventilate the area.
Avoid breathing vapor or mist. Refer to protective measures listed in sections 7 and 8.
Avoid all direct contact with the spilled material. Avoid breathing vapor or mist. Refer to protective measures listed in
sections 7 and 8.
Contain and collect spillage with non-combustible absorbent materials, e.g. sand, earth, vermiculite, diatomaceous
earth, and place in container for disposal according to local regulations (see section 13). Do not allow to enter drains
or watercourses. Clean preferably with a detergent; avoid use of solvents. If the product contaminates lakes, rivers, or
sewers, inform the appropriate authorities in accordance with local regulation.
7.
Handling
Vapors are heavier than air and may spread along floors. Vapors may form explosive mixtures with air. Prevent the
creation of flammable or explosive concentrations of vapors in air and avoid vapor concentrations higher than the
occupational exposure limits. In addition, the product should be used only in areas from which all naked lights and
other sources of ignition have been excluded. Electrical equipment should be protected to the appropriate standard.
To dissipate static electricity during transfer, ground drum and connect to receiving container with bonding strap. No
sparking tools should be used.
Avoid inhalation of vapour, dust and spray mist. Avoid contact with skin and eyes. Eating, drinking and smoking should
be prohibited in area where this material is handled, stored and processed. Appropriate personal protective
equipment: see Section 8. Always keep in containers made from the same material as the original one.
Storage
Store in accordance with local regulations for flammable liquids. Observe label precautions. Store in a cool, wellventilated area away from incompatible materials and ignition sources. Keep out of the reach of children.
Keep away from: Oxidizing agents, strong alkalis, strong acids. No smoking. Prevent unauthorized access. Containers
that are opened must be carefully resealed and kept upright to prevent leakage.
8.
Engineering measures
Hygiene measures
: Gloves must be worn for all work that may result in soiling.
Apron/coveralls/protective clothing must be worn when soiling is so great that
regular work clothes do not adequately protect skin against contact with the
product. Safety eyewear should be used when there is a likelihood of exposure.
Wear suitable protective clothing. Always wear protective clothing when spraying.
:
: Wear suitable gloves. Barrier creams may help to protect the exposed areas of
the skin, but should not be applied once exposure has occurred. Barrier creams
may not be used under or instead of gloves.
It is not possible to specify precise type of gloves, since the actual work situation
is unknown. Supplier of gloves should be contacted in order to find the appropriate
type.
Use safety eyewear designed to protect against splash of liquids.
Eyes
Date of issue
: 7/18/2005.
Page: 2/4
9.
0808000000
Physical state
Density
: Liquid.
: 0.87 g/cm3
Solubility
Flash point
Autoignition temperature
: The lowest known value is 450C based on data for: solvent naphtha (petroleum),
Explosion Limits
Kinematic Viscosity
% Solvent by Weight
% Water by Weight
VOC Content
TOC Content
Solvent Gas
:
:
:
:
:
:
:
light arom.
0.5 - 8 vol %
6
Test
Result
Route
Species
LD50
LC50
8400 mg/kg
2000 ppm (4 hour/hours)
Oral
Inhalation
Rat
Rat
Date of issue
: 7/18/2005.
Page: 3/4
0808000000
UN1263
Class
PG*
III
Label
Additional information
Remarks
H-14
IMDG
Class
UN1263
Emergency schedules
(EmS)
III
3
F-E, S-E
Safety Phrases
Other EU Regulations
Classification and labeling have been performed according to EU Directives 67/548/EEC and 1999/45/EC (including
amendments) and the intended use.
- Industrial applications, Used by spraying.
Child Protection
: Yes, applicable.
Tactile warning of danger
: Yes, applicable.
: R10- Flammable.
R20- Harmful by inhalation.
R65- Harmful: may cause lung damage if swallowed.
R36/37/38- Irritating to eyes, respiratory system and skin.
R51/53- Toxic to aquatic organisms, may cause long-term adverse effects in the aquatic environment.
Notice to Reader
Modified data or content compared with the previous version are maked with a triangular marker in the upper-left
corner within the Safety Data Sheet.
The information contained in this safety data sheet is based on the present state of knowledge and EU and national
legislation. It provides guidance on health, safety and environmental aspects for handling the product in a safe way
and should not be construed as any guarantee of the technical preformance or suitability for particular applications.
It is always the duty of the user/employer to ascertain that the work is planned and carried out in accordance with the
national regulations.
Date of issue
: 7/18/2005.
Page: 4/4
Product Type
:
:
:
:
Field of application
Date of issue
Date of Previous Issue
2.
0845000000
Hempel A/S
Lundtoftevej 150
DK-2800 Kgs. Lyngby
Denmark
Tel.: + 45 45 93 38 00
Emergency phone:
+45 45 93 38 00
See section 4 First aid
measures.
thinner
private (yacht), ships and shipyards. buildings and metal industry.
28-09-2005.
22-12-2004.
Composition/information on ingredients
Substances presenting a health or environmental hazard within the meaning of the Dangerous Substances Directive
67/548/EEC.
Ingredient Name
CAS No.
EC Number
Classification
xylene
1330-20-7
40 - 50
215-535-7
butan-1-ol
71-36-3
20 - 30
200-751-6
64742-95-6
15 - 20
265-199-0
ethylbenzene
100-41-4
5 - 10
202-849-4
R10
Xn; R20/21
Xi; R38
R10
Xn; R22
Xi; R37/38, R41
R67
Xn; R20, R65
Xi; R36/37/38
N; R51/53
F; R11
Xn; R20
.
Notes
(*) See full text of phrases under section 16 and occupational Exposure Limit(s), if available, are listed in section 8
3.
Hazards identification
Harmful
Flammable Harmful by inhalation, in contact with skin and if swallowed. Risk of serious damage to eyes. Irritating to
respiratory system and skin. Harmful: may cause lung damage if swallowed. Harmful to aquatic organisms, may cause
long-term adverse effects in the aquatic environment.
4.
General
: In all cases of doubt, or when symptoms persist, seek medical attention. Never
give anything by mouth to an unconscious person.
Move the person into fresh air and keep the person under surveillance. Keep
person warm and at rest. If not breathing, if breathing is irregular or if respiratory
arrest occurs, provide artificial respiration or oxygen by trained personnel. Give
nothing by mouth. If unconscious, place in recovery position and seek medical
advice.
Inhalation
Date of issue
: 28-09-2005.
Page: 1/5
0845000000
: Check for and remove any contact lenses. Immediately flush eyes with plenty of
water for at least 5 minutes, occasionally lifting the upper and lower eyelids. In all
cases of doubt, or when symptoms persist, seek medical attention.
Skin Contact
: Remove contaminated clothing and shoes. Wash skin thoroughly with soap and
water or use recognized skin cleanser. Do not use solvents or thinners.
Ingestion
: If swallowed, seek medical advice immediately and show this document. Keep
person warm and at rest. Do NOT induce vomiting unless directed to do so by
medical personnel. Lower the head so that the vomit will not reenter the mouth
and throat.
5.
Fire-fighting measures
Fire will produce dense black smoke. Exposure to decomposition products may cause a health hazard. Fire-fighters
should wear appropriate protective equipment. Cool closed containers exposed to fire with water. Do not release
runoff from fire to sewers or waterways.
Extinguishing Media
: Recommended: alcohol resistant foam, CO2, powders, water spray.
Not to be used : waterjet.
Fire Degradation Products
: These products are carbon oxides (CO, CO2).
6.
Exclude sources of ignition and be aware of explosion hazard. Ventilate the area.
Contain and collect spillage with non-combustible absorbent materials, e.g. sand, earth, vermiculite, diatomaceous
earth, and place in container for disposal according to local regulations (see section 13). Do not allow to enter drains
or watercourses. Clean preferably with a detergent; avoid use of solvents. If the product contaminates lakes, rivers, or
sewers, inform the appropriate authorities in accordance with local regulation.
7.
Handling
Vapors are heavier than air and may spread along floors. Vapors may form explosive mixtures with air. Prevent the
creation of flammable or explosive concentrations of vapors in air and avoid vapor concentrations higher than the
occupational exposure limits. In addition, the product should be used only in areas from which all naked lights and
other sources of ignition have been excluded. Electrical equipment should be protected to the appropriate standard.
To dissipate static electricity during transfer, ground drum and connect to receiving container with bonding strap. No
sparking tools should be used.
Avoid inhalation of vapour, dust and spray mist. Avoid contact with skin and eyes. Eating, drinking and smoking should
be prohibited in area where this material is handled, stored and processed. Appropriate personal protective
equipment: see Section 8. Always keep in containers made from the same material as the original one.
Storage
Store in accordance with local regulations for flammable liquids. Observe label precautions. Store in a cool, wellventilated area away from incompatible materials and ignition sources. Keep out of the reach of children.
Keep away from: Oxidizing agents, strong alkalis, strong acids. No smoking. Prevent unauthorized access. Containers
that are opened must be carefully resealed and kept upright to prevent leakage.
8.
Engineering measures
Hygiene measures
Ingredient Name
xylene
butan-1-ol
ethylbenzene
Date of issue
: 28-09-2005.
Page: 2/5
0845000000
: Gloves must be worn for all work that may result in soiling.
Hands
: Wear suitable gloves. Barrier creams may help to protect the exposed areas of
Respiratory system
Eyes
9.
the skin, but should not be applied once exposure has occurred. Barrier creams
may not be used under or instead of gloves.
It is not possible to specify precise type of gloves, since the actual work situation
is unknown. Supplier of gloves should be contacted in order to find the appropriate
type.
face shield or safety glasses with side shields.
Physical state
Density
: Liquid.
: Weighted average: 0.85 g/cm 3
Solubility
Flash point
Explosion Limits
:
:
:
:
:
:
:
Kinematic Viscosity
% Solvent by Weight
% Water by Weight
VOC Content
TOC Content
Solvent Gas
Date of issue
Test
: 28-09-2005.
Result
Route
Species
Page: 3/5
0845000000
xylene
LD50
LD50
LDLo
LC50
LD50
LD50
LD50
LC50
LD50
butan-1-ol
solvent naphtha (petroleum), light arom.
ethylbenzene
4300 mg/kg
>1700 mg/kg
50 mg/kg
>6700 ppm (4 hour/hours)
790 mg/kg
3400 mg/kg
8400 mg/kg
2000 ppm (4 hour/hours)
3500 mg/kg
Oral
Dermal
Oral
Inhalation
Oral
Dermal
Oral
Inhalation
Oral
Rat
Rabbit
Human
Rat
Rat
Rabbit
Rat
Rat
Rat
Species
Period
Result
xylene
butan-1-ol
96 hour/hours
48 hour/hours
96 hour/hours
48 hour/hours
48 hour/hours
96 hour/hours
8.2 mg/l
1983 mg/l
1910 mg/l
2.93 mg/l
7.2 mg/l
9.09 mg/l
ethylbenzene
UN1263
Class
PG*
III
Label
Additional information
Remarks
H-14
IMDG
Class
UN1263
Emergency schedules
(EmS)
III
3
F-E, S-E
: xylene
butan-1-ol
R10- Flammable.
R20/21/22- Harmful by inhalation, in contact with skin and if swallowed.
R65- Harmful: may cause lung damage if swallowed.
R37/38- Irritating to respiratory system and skin.
R41- Risk of serious damage to eyes.
R52/53- Harmful to aquatic organisms, may cause long-term adverse effects in
the aquatic environment.
Risk Phrases
Date of issue
: 28-09-2005.
Page: 4/5
0845000000
Other EU Regulations
Classification and labeling have been performed according to EU directives 67/548/EEC, 1999/45/EC including
amendments and the intended use.
- Industrial applications, Used by Spraying.
Child Protection
: Yes, applicable.
Tactile warning of danger
: Yes, applicable.
Notice to Reader
Modified data or content compared with the previous version are maked with a triangular marker in the upper-left
corner within the Safety Data Sheet.
The information contained in this safety data sheet is based on the present state of knowledge and EU and national
legislation. It provides guidance on health, safety and environmental aspects for handling the product in a safe way
and should not be construed as any guarantee of the technical preformance or suitability for particular applications.
It is always the duty of the user/employer to ascertain that the work is planned and carried out in accordance with the
national regulations.
Date of issue
: 28-09-2005.
Page: 5/5
1.
Company details
Product type
:
:
:
:
:
Field of application
ready-for-use mixture
Date of issue
Date of previous issue
2.
Hazards identification
Irritant
Flammable. Irritating to eyes and skin. May cause sensitization by skin contact. Very toxic to aquatic organisms, may
cause long-term adverse effects in the aquatic environment.
.
3.
Composition/information on ingredients
Substances presenting a health or environmental hazard within the meaning of the Dangerous Substances Directive
67/548/EEC.
Ingredient name
CAS no.
EC number
Classification
7440-66-6
1330-20-7
50 - 75
5 - 10
231-175-3
215-535-7
25068-38-6
3-5
500-033-5
28064-14-4
3-5
n-butanol
71-36-3
3-5
200-751-6
64742-95-6
1-3
265-199-0
ethylbenzene
100-41-4
1-3
202-849-4
(C12-C14) Alkylglycidylether
68609-97-2
1-3
271-846-8
N; R50/53
R10
Xn; R20/21
Xi; R38
Xi; R36/38
R43
N; R51/53
Xi; R36/38
R43
N; R51/53
R10
Xn; R22
Xi; R41, R37/38
R67
R10
Xn; R20, R65
Xi; R36/37/38
N; R51/53
F; R11
Xn; R20
Xi; R38
R43
.
Notes
(*) See full text of phrases under chapter 16. Occupational exposure limits, if available, are listed in section 8.
Date of issue
: 7/9/2007.
Page: 1/5
1734919830
4.
General
: In all cases of doubt, or when symptoms persist, seek medical attention. Never
Inhalation
Eye contact
Skin contact
Ingestion
5.
Fire-fighting measures
Promptly isolate the scene by removing all persons from the vicinity of the incident if there is a fire. No action shall be
taken involving any personal risk or without suitable training. Fire will produce dense black smoke. Exposure to
decomposition products may cause a health hazard. Cool closed containers exposed to fire with water. Do not release
runoff from fire to sewers or waterways. Fire-fighters should wear appropriate protective equipment and self-contained
breathing apparatus (SCBA) with a full face-piece operated in positive pressure mode.
Extinguishing media
6.
Do not use water. Violent reaction may occur. Exclude sources of ignition and be aware of explosion hazard. Ventilate
the area. Avoid breathing vapor or mist. Refer to protective measures listed in sections 7 and 8.
Contain and collect spillage with non-combustible absorbent materials, e.g. sand, earth, vermiculite, diatomaceous
earth, and place in container for disposal according to local regulations (see section 13). Do not allow to enter drains
or watercourses. Clean preferably with a detergent; avoid use of solvents. If the product contaminates lakes, rivers, or
sewers, inform the appropriate authorities in accordance with local regulation.
.
7.
Handling
Vapors are heavier than air and may spread along floors. Vapors may form explosive mixtures with air. Prevent the
creation of flammable or explosive concentrations of vapors in air and avoid vapor concentrations higher than the
occupational exposure limits. In addition, the product should be used only in areas from which all naked lights and
other sources of ignition have been excluded. Electrical equipment should be protected to the appropriate standard.
To dissipate static electricity during transfer, ground drum and connect to receiving container with bonding strap. No
sparking tools should be used. Contains epoxy constituents. Avoid all possible skin contact with epoxy and amine
containing products, they may cause allergic reactions. Open with care, danger of overpressure.
Avoid inhalation of vapour, dust and spray mist. Avoid contact with skin and eyes. Eating, drinking and smoking should
be prohibited in area where this material is handled, stored and processed. Appropriate personal protective
equipment: see Section 8. Always keep in containers made from the same material as the original one.
Storage
Store in accordance with local regulations for flammable liquids. Store in a cool, well-ventilated area away from
incompatible materials and ignition sources. Keep out of the reach of children. Keep away from: Oxidizing agents,
strong alkalis, strong acids. No smoking. Prevent unauthorized access. Containers that are opened must be carefully
resealed and kept upright to prevent leakage.
Date of issue
: 7/9/2007.
Page: 2/5
1734919830
8.
Engineering measures
Hygiene measures
: Wash hands, forearms, and face thoroughly after handling compounds and before
eating, smoking, using lavatory, and at the end of day.
Ingredient name
xylene
n-butanol
solvent naphtha (petroleum), light arom.
ethylbenzene
Respiratory protection
Skin protection
Hand protection
: Gloves must be worn for all work that may result in soiling.
: Wear suitable protective clothing. Always wear protective clothing when spraying.
: Wear suitable gloves. For prolonged or repeated handling, use gloves. Barrier
creams may help to protect the exposed areas of the skin, but should not be
applied once exposure has occurred. Barrier creams may not be used under or
instead of gloves.
Since the actual work situation is unknown. Supplier of gloves should be
contacted in order to find the appropriate type.
Eye protection
: Use safety eyewear designed to protect against splash of liquids. Safety glasses
with side shields.
9.
Physical state
Density
: Liquid.
: 2.64 g/cm3
Solubility
Flash point
: Partially soluble in the following materials: cold water and hot water.
: Closed cup: 30C (86F)
Explosion limits
Solvent Gas
:
:
:
:
:
:
Date of issue
: 7/9/2007.
Solvent(s) % by weight
Water % by weight
VOC content
TOC Content
Page: 3/5
1734919830
Stable under recommended storage and handling conditions (see section 7). AVOID WATER. Risk of formation of
very flammable and explosive vapours.
Highly reactive or incompatible with the following materials: oxidizing materials and acids.
Reactive or incompatible with the following materials: reducing materials, organic materials, metals and alkalis.
When exposed to high temperatures (i.e. in case of fire) harmful decomposition products may be formed:
Decomposition products may include the following materials: carbon oxides halogenated compounds metal
oxide/oxides
.
: Contains bisphenol A-(epichlorhydrin) epoxy resin MW =< 700, bisphenol F(epichlorhydrin) epoxy resin MW =< 700, (C12-C14) Alkylglycidylether. May
produce an allergic reaction.
Acute toxicity
Ingredient name
Result
Dose
Species
xylene
LD50 Oral
LD50 Skin
LDLo Oral
LD50 Oral
LD50 Oral
LD50 Oral
LD50 Skin
LD50 Oral
4300 mg/kg
>1700 mg/kg
50 mg/kg
790 mg/kg
8400 mg/kg
3500 mg/kg
17800 uL/kg
17100 mg/kg
Rat
Rabbit
Human
Rat
Rat
Rat
Rabbit
Rat
n-butanol
solvent naphtha (petroleum), light arom.
ethylbenzene
(C12-C14) Alkylglycidylether
.
Do not allow to enter drains or watercourses. Very toxic to aquatic organisms, may cause long-term adverse effects in
the aquatic environment.
Ingredient name
Result
xylene
n-butanol
ethylbenzene
Intoxication
Mortality
Mortality
Intoxication
Mortality
Intoxication
Mortality
Species
Exposure
Daphnia
Fish
Fish
Daphnia
Fish
Daphnia
Fish
48 hours
96 hours
96 hours
48 hours
96 hours
48 hours
96 hours
Date of issue
: 7/9/2007.
Page: 4/5
1734919830
UN1263
Class
PG*
III
Label
Additional information
Remarks
H-14
IMDG
Class
UN1263
PAINT
III
3
Emergency schedules
(EmS)
F-E, S-E
Classification and labeling have been determined according to EU Directives 67/548/EEC and 1999/45/EC (including
amendments) and take into account the intended product use.
Product use
Symbol
Contains
Risk phrases
Safety phrases
Notice to reader
Modified data or content compared with the previous version are maked with a triangular marker in the upper-left
corner within the Safety Data Sheet.
The information contained in this safety data sheet is based on the present state of knowledge and EU and national
legislation. It provides guidance on health, safety and environmental aspects for handling the product in a safe way
and should not be construed as any guarantee of the technical preformance or suitability for particular applications.
It is always the duty of the user/employer to ascertain that the work is planned and carried out in accordance with the
national regulations.
Date of issue
: 7/9/2007.
Page: 5/5
Product Type
:
:
:
:
:
Field of application
Ready for use mixture
Date of issue
Date of Previous Issue
2.
5521910170
Hempel A/S
Lundtoftevej 150
DK-2800 Kgs. Lyngby
Denmark
Tel.: + 45 45 93 38 00
Emergency phone:
+45 45 93 38 00
See section 4 First aid
measures.
Composition/information on ingredients
Substances presenting a health or environmental hazard within the meaning of the Dangerous Substances Directive
67/548/EEC.
Ingredient Name
CAS No.
EC Number
Classification
64742-95-6
20 - 30
265-199-0
xylene
1330-20-7
5 - 10
215-535-7
ethylbenzene
100-41-4
1-3
202-849-4
41556-26-7
0.2 - 0.5
255-437-1
n-butyl acrylate
141-32-2
0.15 - 0.2
205-480-7
.
Notes
(*) See full text of phrases under section 16 and occupational Exposure Limit(s), if available, are listed in section 8
3.
Hazards identification
Harmful
Flammable. Harmful by inhalation. Irritating to eyes, respiratory system and skin. Toxic to aquatic organisms, may
cause long-term adverse effects in the aquatic environment. Contains (bis (1,2,2,6,6-pentamethyl-4-piperidyl)
sebacate, n-butyl acrylate). May produce an allergic reaction.
Date of issue
: 7/21/2005.
Page: 1/5
4.
5521910170
General
: In all cases of doubt, or when symptoms persist, seek medical attention. Never
Inhalation
Eye Contact
Skin Contact
Ingestion
5.
Fire-fighting measures
Fire will produce dense black smoke. Exposure to decomposition products may cause a health hazard. Fire-fighters
should wear appropriate protective equipment. Cool closed containers exposed to fire with water. Do not release
runoff from fire to sewers or waterways.
Extinguishing Media
: Recommended: alcohol resistant foam, CO2, powders, water spray.
Not to be used : waterjet.
Fire Degradation Products
: These products are carbon oxides (CO, CO2). Some metallic oxides.
6.
Exclude sources of ignition and be aware of explosion hazard. Ventilate the area.
Avoid all direct contact with the spilled material. Avoid breathing vapor or mist. Refer to protective measures listed in
sections 7 and 8.
Contain and collect spillage with non-combustible absorbent materials, e.g. sand, earth, vermiculite, diatomaceous
earth, and place in container for disposal according to local regulations (see section 13). Do not allow to enter drains
or watercourses. Clean preferably with a detergent; avoid use of solvents. If the product contaminates lakes, rivers, or
sewers, inform the appropriate authorities in accordance with local regulation.
7.
Handling
Vapors are heavier than air and may spread along floors. Vapors may form explosive mixtures with air. Prevent the
creation of flammable or explosive concentrations of vapors in air and avoid vapor concentrations higher than the
occupational exposure limits. In addition, the product should be used only in areas from which all naked lights and
other sources of ignition have been excluded. Electrical equipment should be protected to the appropriate standard.
To dissipate static electricity during transfer, ground drum and connect to receiving container with bonding strap. No
sparking tools should be used.
Avoid inhalation of vapour, dust and spray mist. Avoid contact with skin and eyes. Eating, drinking and smoking should
be prohibited in area where this material is handled, stored and processed. Appropriate personal protective
equipment: see Section 8. Always keep in containers made from the same material as the original one.
Storage
Store in accordance with local regulations for flammable liquids. Observe label precautions. Store in a cool, wellventilated area away from incompatible materials and ignition sources. Keep out of the reach of children.
Keep away from: Oxidizing agents, strong alkalis, strong acids. No smoking. Prevent unauthorized access. Containers
that are opened must be carefully resealed and kept upright to prevent leakage.
Date of issue
: 7/21/2005.
Page: 2/5
8.
5521910170
Engineering measures
Hygiene measures
Ingredient Name
xylene
ethylbenzene
n-butyl acrylate
Respiratory system
Eyes
9.
: Gloves must be worn for all work that may result in soiling.
Apron/coveralls/protective clothing must be worn when soiling is so great that
regular work clothes do not adequately protect skin against contact with the
product. Safety eyewear should be used when there is a likelihood of exposure.
: If working areas have insufficient ventilation: When the product is applied by
means that will not generate an aerosol such as, brush or roller wear half or totally
covering mask equipped with gas filter of type A, when grinding use particle filter
of type P.
When the product is applied by spraying and for continuous or prolonged work
always wear an air-fed respirator e.g. hood with supply of fresh or compressed air
or a full face, powered air purifying filter. Be sure to use approved/certified filter,
respirator or equivalent.
: Wear suitable protective clothing. Always wear protective clothing when spraying.
: Wear suitable gloves. Barrier creams may help to protect the exposed areas of
the skin, but should not be applied once exposure has occurred. Barrier creams
may not be used under or instead of gloves.
It is not possible to specify precise type of gloves, since the actual work situation
is unknown. Supplier of gloves should be contacted in order to find the appropriate
type.
Use safety eyewear designed to protect against splash of liquids.
Physical state
Density
: Liquid.
: Weighted average: 1.28 g/cm 3
Solubility
Flash point
Explosion Limits
Solvent Gas
:
:
:
:
:
:
Date of issue
: 7/21/2005.
% Solvent by Weight
% Water by Weight
VOC Content
TOC Content
0.5 - 8 vol %
Weighted average: 37 %
Weighted average: 0 %
Weighted average: 475 g/l (CEPE)
Weighted average: 431 g/l (based on data for: Solvent.)
0.103 m 3/l
Page: 3/5
5521910170
Test
Result
Route
Species
LD50
LC50
LD50
LD50
LDLo
LC50
LD50
LD50
LDLo
8400 mg/kg
2000 ppm (4 hour/hours)
4300 mg/kg
>1700 mg/kg
50 mg/kg
>6700 ppm (4 hour/hours)
3500 mg/kg
900 mg/kg
1700 mg/kg
Oral
Inhalation
Oral
Dermal
Oral
Inhalation
Oral
Oral
Dermal
Rat
Rat
Rat
Rabbit
Human
Rat
Rat
Rat
Rat
xylene
ethylbenzene
n-butyl acrylate
Species
Period
Result
xylene
ethylbenzene
96 hour/hours
48 hour/hours
48 hour/hours
96 hour/hours
8.2 mg/l
2.93 mg/l
7.2 mg/l
9.09 mg/l
UN1263
Class
PG*
III
Label
Additional information
Remarks
H-14
Date of issue
: 7/21/2005.
Page: 4/5
UN1263
5521910170
PAINT
Emergency schedules
(EmS)
III
3
F-E, S-E
Safety Phrases
Other EU Regulations
Classification and labeling have been performed according to EU Directives 67/548/EEC and 1999/45/EC (including
amendments) and the intended use.
- Industrial applications, Used by spraying.
Notice to Reader
Modified data or content compared with the previous version are maked with a triangular marker in the upper-left
corner within the Safety Data Sheet.
The information contained in this safety data sheet is based on the present state of knowledge and EU and national
legislation. It provides guidance on health, safety and environmental aspects for handling the product in a safe way
and should not be construed as any guarantee of the technical preformance or suitability for particular applications.
It is always the duty of the user/employer to ascertain that the work is planned and carried out in accordance with the
national regulations.
Date of issue
: 7/21/2005.
Page: 5/5
Product Type
:
:
:
:
Field of application
Date of issue
Date of Previous Issue
2.
6750099980
Hempel A/S
Lundtoftevej 150
DK-2800 Kgs. Lyngby
Denmark
Tel.: + 45 45 93 38 00
Emergency phone:
+45 45 93 38 00
See section 4 First aid
measures.
mineral powder
metal industry, ships and shipyards.
7/24/2005.
5/19/2004.
Composition/information on ingredients
Substances presenting a health or environmental hazard within the meaning of the Dangerous Substances Directive
67/548/EEC.
Ingredient Name
CAS No.
EC Number
Classification
14808-60-7
14808-60-7
50 - 100
1-3
238-878-4
238-878-4
Not classified.
Not classified.
.
Notes
(*) See full text of phrases under section 16 and occupational Exposure Limit(s), if available, are listed in section 8
3.
Hazards identification
4.
General
: In all cases of doubt, or when symptoms persist, seek medical attention. Never
Inhalation
Eye Contact
:
:
Skin Contact
Ingestion
5.
Fire-fighting measures
Exposure to decomposition products may cause a health hazard. Fire-fighters should wear appropriate protective
equipment. Cool closed containers exposed to fire with water. Do not release runoff from fire to sewers or waterways.
Extinguishing Media
: Recommended: alcohol resistant foam, CO2, powders, water spray.
Not to be used : waterjet.
Fire Degradation Products
: Some metallic oxides.
Date of issue
: 7/24/2005.
Page: 1/3
6.
6750099980
Contain and collect spillage, keep spillage wetted to avoid dusting when handling. Place in container for disposal
according to local regulations (see section 13). Do not allow to enter drains or watercourses. Clean preferably with a
detergent; avoid use of solvents. If the product contaminates lakes, rivers, or sewers, inform the appropriate
authorities in accordance with local regulation.
7.
Handling
Avoid inhalation of vapour, dust and spray mist. Avoid contact with skin and eyes. Eating, drinking and smoking should
be prohibited in area where this material is handled, stored and processed. Appropriate personal protective
equipment: see Section 8. Always keep in containers made from the same material as the original one.
Storage
Keep away from: Oxidizing agents, strong alkalis, strong acids. No smoking. Prevent unauthorized access. Containers
that are opened must be carefully resealed and kept upright to prevent leakage.
8.
Engineering measures
Hygiene measures
Ingredient Name
Respirable quartz
Respiratory system
9.
: Gloves must be worn for all work that may result in soiling.
Apron/coveralls/protective clothing must be worn when soiling is so great that
regular work clothes do not adequately protect skin against contact with the
product. Safety eyewear should be used when there is a likelihood of exposure.
: Wear appropriate respirator when ventilation is inadequate. Be sure to use
approved/certified respirator or equivalent. Always wear air-fed respirator when
spraying. It is not possible to specify precise filter type, since the actual work
situation is unknown. Supplier of respirators should be contacted in order to find
the appropriate filter.
: If necessary wear protective clothing. Always wear protective clothing when
spraying.
: Wear suitable gloves. Barrier creams may help to protect the exposed areas of
the skin, but should not be applied once exposure has occurred. Barrier creams
may not be used under or instead of gloves.
It is not possible to specify precise type of gloves, since the actual work situation
is unknown. Supplier of gloves should be contacted in order to find the appropriate
type.
Physical state
Solid.
Solvent Gas
:
:
:
:
:
:
:
:
Date of issue
: 7/24/2005.
Melting Point
Density
% Solvent by Weight
% Water by Weight
VOC Content
TOC Content
Page: 2/3
6750099980
Class
PG*
Label
Additional information
ADR/RID
Class
IMDG
Class
Other EU Regulations
Classification and labeling have been performed according to EU Directives 67/548/EEC and 1999/45/EC (including
amendments) and the intended use.
- Industrial applications, Used by spraying.
Date of issue
: 7/24/2005.
Page: 3/3
1.
Product type
Field of application
ready-for-use mixture
Date of issue
Date of previous issue
: HEMPADUR 15599
1559956880
: Hempel A/S
Lundtoftevej 150
DK-2800 Kgs. Lyngby
Denmark
Tel.: + 45 45 93 38 00
hempel@dk.hempel.com
:
:
:
:
:
2.
Hazards identification
Harmful
Flammable. Harmful by inhalation and in contact with skin. Irritating to eyes and skin. May cause sensitization by skin
contact. Harmful to aquatic organisms, may cause long-term adverse effects in the aquatic environment.
.
3.
Composition/information on ingredients
Substances presenting a health or environmental hazard within the meaning of the Dangerous Substances Directive
67/548/EEC.
Ingredient name
CAS no.
EC number
middlemolecular epoxyresin
15 - 25
xylene
1330-20-7
15 - 25
215-535-7
n-butanol
71-36-3
5 - 10
200-751-6
1-methoxy-2-propanol
solvent naphtha (petroleum), light arom.
107-98-2
64742-95-6
3-5
3-5
203-539-1
265-199-0
ethylbenzene
100-41-4
3-5
202-849-4
64742-82-1
0.1 - 0.15
265-185-4
Classification
Xi; R36/38
R43
R10
Xn; R20/21
Xi; R38
R10
Xn; R22
Xi; R41, R37/38
R67
R10
R10
Xn; R20, R65
Xi; R36/37/38
N; R51/53
F; R11
Xn; R20
Xn; R65
N; R51/53
.
Notes
(*) See full text of phrases under chapter 16. Occupational exposure limits, if available, are listed in section 8.
Date of issue
: 7/9/2007.
Page: 1/5
HEMPADUR 15599
1559956880
4.
General
Inhalation
Eye contact
Skin contact
Ingestion
: In all cases of doubt, or when symptoms persist, seek medical attention. Never
: Check for and remove any contact lenses. Immediately flush eyes with plenty of
water for at least 15 minutes, occasionally lifting the upper and lower eyelids. Seek
immediate medical attention.
: Remove contaminated clothing and shoes. Wash skin thoroughly with soap and
water or use recognized skin cleanser. Do not use solvents or thinners.
: If swallowed, seek medical advice immediately and show this container or label.
Keep person warm and at rest. Do not induce vomiting unless directed to do so by
medical personnel. Lower the head so that vomit will not re-enter the mouth and
throat.
5.
Fire-fighting measures
Promptly isolate the scene by removing all persons from the vicinity of the incident if there is a fire. No action shall be
taken involving any personal risk or without suitable training. Fire will produce dense black smoke. Exposure to
decomposition products may cause a health hazard. Cool closed containers exposed to fire with water. Do not release
runoff from fire to sewers or waterways. Fire-fighters should wear appropriate protective equipment and self-contained
breathing apparatus (SCBA) with a full face-piece operated in positive pressure mode.
Extinguishing media
Fire degradation products
6.
Avoid all direct contact with the spilled material. Exclude sources of ignition and be aware of explosion hazard.
Ventilate the area. Avoid breathing vapor or mist. Refer to protective measures listed in sections 7 and 8.
Contain and collect spillage with non-combustible absorbent materials, e.g. sand, earth, vermiculite, diatomaceous
earth, and place in container for disposal according to local regulations (see section 13). Do not allow to enter drains
or watercourses. Clean preferably with a detergent; avoid use of solvents. If the product contaminates lakes, rivers, or
sewers, inform the appropriate authorities in accordance with local regulation.
.
7.
Handling
Vapors are heavier than air and may spread along floors. Vapors may form explosive mixtures with air. Prevent the
creation of flammable or explosive concentrations of vapors in air and avoid vapor concentrations higher than the
occupational exposure limits. In addition, the product should be used only in areas from which all naked lights and
other sources of ignition have been excluded. Electrical equipment should be protected to the appropriate standard.
To dissipate static electricity during transfer, ground drum and connect to receiving container with bonding strap. No
sparking tools should be used. Contains epoxy constituents. Avoid all possible skin contact with epoxy and amine
containing products, they may cause allergic reactions.
Avoid inhalation of vapour, dust and spray mist. Avoid contact with skin and eyes. Eating, drinking and smoking should
be prohibited in area where this material is handled, stored and processed. Appropriate personal protective
equipment: see Section 8. Always keep in containers made from the same material as the original one.
Storage
Store in accordance with local regulations for flammable liquids. Store in a cool, well-ventilated area away from
incompatible materials and ignition sources. Keep out of the reach of children. Keep away from: Oxidizing agents,
strong alkalis, strong acids. No smoking. Prevent unauthorized access. Containers that are opened must be carefully
resealed and kept upright to prevent leakage.
Date of issue
: 7/9/2007.
Page: 2/5
HEMPADUR 15599
1559956880
8.
Engineering measures
Hygiene measures
: Wash hands, forearms, and face thoroughly after handling compounds and before
eating, smoking, using lavatory, and at the end of day.
Ingredient name
xylene
n-butanol
1-methoxy-2-propanol
ethylbenzene
Respiratory protection
Skin protection
Hand protection
: Gloves must be worn for all work that may result in soiling.
: Wear suitable protective clothing. Always wear protective clothing when spraying.
: Wear suitable gloves. For prolonged or repeated handling, use gloves. Barrier
creams may help to protect the exposed areas of the skin, but should not be
applied once exposure has occurred. Barrier creams may not be used under or
instead of gloves.
Since the actual work situation is unknown. Supplier of gloves should be
contacted in order to find the appropriate type.
Eye protection
: Use safety eyewear designed to protect against splash of liquids. Safety glasses
with side shields.
9.
Physical state
Density
: Liquid.
: 1.43 g/cm3
Solubility
Flash point
: Partially soluble in the following materials: cold water and hot water.
: Closed cup: 26C (78.8F)
Explosion limits
Water % by weight
Date of issue
: 7/9/2007.
Solvent(s) % by weight
Page: 3/5
HEMPADUR 15599
VOC content
TOC Content
Solvent Gas
1559956880
Stable under recommended storage and handling conditions (see section 7).
Highly reactive or incompatible with the following materials: oxidizing materials and metals.
Reactive or incompatible with the following materials: reducing materials.
When exposed to high temperatures (i.e. in case of fire) harmful decomposition products may be formed:
Decomposition products may include the following materials: carbon oxides sulfur oxides metal oxide/oxides
.
Acute toxicity
Ingredient name
Result
Dose
Species
xylene
LD50 Oral
LD50 Skin
LDLo Oral
LD50 Oral
LD50 Oral
LD50 Skin
LD50 Oral
LD50 Oral
LD50 Skin
4300 mg/kg
>1700 mg/kg
50 mg/kg
790 mg/kg
6600 mg/kg
13000 mg/kg
8400 mg/kg
3500 mg/kg
17800 uL/kg
Rat
Rabbit
Human
Rat
Rat
Rabbit
Rat
Rat
Rabbit
n-butanol
1-methoxy-2-propanol
solvent naphtha (petroleum), light arom.
ethylbenzene
.
Do not allow to enter drains or watercourses. Harmful to aquatic organisms, may cause long-term adverse effects in
the aquatic environment.
Ingredient name
Result
xylene
n-butanol
ethylbenzene
Mortality
Intoxication
Mortality
Intoxication
Mortality
Species
Exposure
Fish
Daphnia
Fish
Daphnia
Fish
96 hours
48 hours
96 hours
48 hours
96 hours
Date of issue
: 7/9/2007.
Page: 4/5
HEMPADUR 15599
1559956880
UN1263
Class
PG*
III
Label
Additional information
Remarks
H-14
IMDG
Class
UN1263
PAINT
III
3
Emergency schedules
(EmS)
F-E, S-E
Classification and labeling have been determined according to EU Directives 67/548/EEC and 1999/45/EC (including
amendments) and take into account the intended product use.
Product use
Symbol
Contains
Risk phrases
Safety phrases
xylene
: R10- Flammable.
R20/21- Harmful by inhalation and in contact with skin.
R36/38- Irritating to eyes and skin.
R43- May cause sensitization by skin contact.
R52/53- Harmful to aquatic organisms, may cause long-term adverse effects in
the aquatic environment.
Notice to reader
Modified data or content compared with the previous version are maked with a triangular marker in the upper-left
corner within the Safety Data Sheet.
The information contained in this safety data sheet is based on the present state of knowledge and EU and national
legislation. It provides guidance on health, safety and environmental aspects for handling the product in a safe way
and should not be construed as any guarantee of the technical preformance or suitability for particular applications.
It is always the duty of the user/employer to ascertain that the work is planned and carried out in accordance with the
national regulations.
Date of issue
: 7/9/2007.
Page: 5/5
1.
Product type
Field of application
ready-for-use mixture
Date of issue
Date of previous issue
:
:
:
:
:
curing agent
used only as part of two- or multi component products.
(see base component)
7/11/2007.
10/28/2005.
2.
Hazards identification
Harmful
Flammable. Harmful by inhalation, in contact with skin and if swallowed. Risk of serious damage to eyes. Irritating to
respiratory system and skin. Harmful to aquatic organisms, may cause long-term adverse effects in the aquatic
environment.
.
3.
Composition/information on ingredients
Substances presenting a health or environmental hazard within the meaning of the Dangerous Substances Directive
67/548/EEC.
Ingredient name
CAS no.
EC number
Classification
n-butanol
71-36-3
25 - 50
200-751-6
xylene
1330-20-7
15 - 25
215-535-7
64742-95-6
5 - 10
265-199-0
ethylbenzene
100-41-4
3-5
202-849-4
1-methoxy-2-propanol
107-98-2
3-5
203-539-1
R10
Xn; R22
Xi; R41, R37/38
R67
R10
Xn; R20/21
Xi; R38
R10
Xn; R20, R65
Xi; R36/37/38
N; R51/53
F; R11
Xn; R20
R10
.
Notes
(*) See full text of phrases under chapter 16. Occupational exposure limits, if available, are listed in section 8.
.
4.
General
Inhalation
Date of issue
: In all cases of doubt, or when symptoms persist, seek medical attention. Never
Page: 1/5
9510000000
: Check for and remove any contact lenses. Immediately flush eyes with plenty of
water for at least 15 minutes, occasionally lifting the upper and lower eyelids. Seek
immediate medical attention.
Skin contact
: Remove contaminated clothing and shoes. Wash skin thoroughly with soap and
water or use recognized skin cleanser. Do not use solvents or thinners.
Ingestion
: If swallowed, seek medical advice immediately and show this container or label.
Keep person warm and at rest. Do not induce vomiting unless directed to do so by
medical personnel. Lower the head so that vomit will not re-enter the mouth and
throat.
Notes to physician
: If gasses have been inhaled, from the decomposition of the product, symptoms
may be delayed.
5.
Fire-fighting measures
Promptly isolate the scene by removing all persons from the vicinity of the incident if there is a fire. No action shall be
taken involving any personal risk or without suitable training. Fire will produce dense black smoke. Exposure to
decomposition products may cause a health hazard. Cool closed containers exposed to fire with water. Do not release
runoff from fire to sewers or waterways. Fire-fighters should wear appropriate protective equipment and self-contained
breathing apparatus (SCBA) with a full face-piece operated in positive pressure mode.
Extinguishing media
Fire degradation products
6.
Avoid all direct contact with the spilled material. Exclude sources of ignition and be aware of explosion hazard.
Ventilate the area. Avoid breathing vapor or mist. Refer to protective measures listed in sections 7 and 8.
Contain and collect spillage with non-combustible absorbent materials, e.g. sand, earth, vermiculite, diatomaceous
earth, and place in container for disposal according to local regulations (see section 13). Do not allow to enter drains
or watercourses. Clean preferably with a detergent; avoid use of solvents. If the product contaminates lakes, rivers, or
sewers, inform the appropriate authorities in accordance with local regulation.
.
7.
Handling
Vapors are heavier than air and may spread along floors. Vapors may form explosive mixtures with air. Prevent the
creation of flammable or explosive concentrations of vapors in air and avoid vapor concentrations higher than the
occupational exposure limits. In addition, the product should be used only in areas from which all naked lights and
other sources of ignition have been excluded. Electrical equipment should be protected to the appropriate standard.
To dissipate static electricity during transfer, ground drum and connect to receiving container with bonding strap. No
sparking tools should be used.
Avoid inhalation of vapour, dust and spray mist. Avoid contact with skin and eyes. Eating, drinking and smoking should
be prohibited in area where this material is handled, stored and processed. Appropriate personal protective
equipment: see Section 8. Always keep in containers made from the same material as the original one.
Storage
Store in accordance with local regulations for flammable liquids. Store in a cool, well-ventilated area away from
incompatible materials and ignition sources. Keep out of the reach of children. Keep away from: Oxidizing agents,
strong alkalis, strong acids. No smoking. Prevent unauthorized access. Containers that are opened must be carefully
resealed and kept upright to prevent leakage.
.
8.
Engineering measures
Hygiene measures
: Wash hands, forearms, and face thoroughly after handling compounds and before
eating, smoking, using lavatory, and at the end of day.
Date of issue
: 7/11/2007.
Page: 2/5
9510000000
Ingredient name
n-butanol
xylene
ethylbenzene
1-methoxy-2-propanol
Respiratory protection
Skin protection
Hand protection
: Gloves must be worn for all work that may result in soiling.
: Wear suitable protective clothing. Always wear protective clothing when spraying.
: Wear suitable gloves. For prolonged or repeated handling, use gloves. Barrier
creams may help to protect the exposed areas of the skin, but should not be
applied once exposure has occurred. Barrier creams may not be used under or
instead of gloves.
Since the actual work situation is unknown. Supplier of gloves should be
contacted in order to find the appropriate type.
Eye protection
: Use safety eyewear designed to protect against splash of liquids. Chemical splash
goggles or face shield.
9.
Physical state
Density
: Liquid.
: 1.085 g/cm3
Solubility
Flash point
: Partially soluble in the following materials: cold water and hot water.
: Closed cup: 25C (77F)
Explosion limits
TOC Content
:
:
:
:
:
Solvent Gas
Date of issue
: 7/11/2007.
Solvent(s) % by weight
Water % by weight
VOC content
Page: 3/5
9510000000
Stable under recommended storage and handling conditions (see section 7).
Highly reactive or incompatible with the following materials: oxidizing materials.
Reactive or incompatible with the following materials: reducing materials and metals.
When exposed to high temperatures (i.e. in case of fire) harmful decomposition products may be formed:
Decomposition products may include the following materials: carbon oxides nitrogen oxides
.
Result
Dose
Species
n-butanol
xylene
LD50 Oral
LD50 Oral
LD50 Skin
LDLo Oral
LD50 Oral
LD50 Oral
LD50 Skin
LD50 Oral
LD50 Skin
790 mg/kg
4300 mg/kg
>1700 mg/kg
50 mg/kg
8400 mg/kg
3500 mg/kg
17800 uL/kg
6600 mg/kg
13000 mg/kg
Rat
Rat
Rabbit
Human
Rat
Rat
Rabbit
Rat
Rabbit
Do not allow to enter drains or watercourses. Harmful to aquatic organisms, may cause long-term adverse effects in
the aquatic environment.
Ingredient name
Result
n-butanol
xylene
ethylbenzene
Intoxication
Mortality
Mortality
Intoxication
Mortality
Species
Exposure
Daphnia
Fish
Fish
Daphnia
Fish
48 hours
96 hours
96 hours
48 hours
96 hours
UN1263
Class
PG*
III
Label
Additional information
Remarks
H-14
IMDG
Class
UN1263
PAINT
III
3
Emergency schedules
(EmS)
F-E, S-E
Date of issue
: 7/11/2007.
Page: 4/5
9510000000
Classification and labeling have been determined according to EU Directives 67/548/EEC and 1999/45/EC (including
amendments) and take into account the intended product use.
Product use
Symbol
Contains
Risk phrases
Safety phrases
S26- In case of contact with eyes, rinse immediately with plenty of water and seek
medical advice.
S36/37/39- Wear suitable protective clothing, gloves and eye/face protection.
S51- Use only in well-ventilated areas.
Notice to reader
Modified data or content compared with the previous version are maked with a triangular marker in the upper-left
corner within the Safety Data Sheet.
The information contained in this safety data sheet is based on the present state of knowledge and EU and national
legislation. It provides guidance on health, safety and environmental aspects for handling the product in a safe way
and should not be construed as any guarantee of the technical preformance or suitability for particular applications.
It is always the duty of the user/employer to ascertain that the work is planned and carried out in accordance with the
national regulations.
Date of issue
: 7/11/2007.
Page: 5/5
Product Type
:
:
:
:
Field of application
Date of issue
Date of Previous Issue
2.
9537000000
Hempel A/S
Lundtoftevej 150
DK-2800 Kgs. Lyngby
Denmark
Tel.: + 45 45 93 38 00
Emergency phone:
+45 45 93 38 00
See section 4 First aid
measures.
Composition/information on ingredients
Substances presenting a health or environmental hazard within the meaning of the Dangerous Substances Directive
67/548/EEC.
Ingredient Name
CAS No.
EC Number
Classification
* 28182-81-2
108-65-6
50 - 100
10 - 12.5
500-060-2
203-603-9
xylene
1330-20-7
10 - 12.5
215-535-7
ethylbenzene
100-41-4
1-3
202-849-4
hexamethylene-di-isocyanate
822-06-0
0.2 - 0.5
212-485-8
R43
R10
Xi; R36
R10
Xn; R20/21
Xi; R38
F; R11
Xn; R20
T; R23
Xi; R36/37/38
R42/43
.
Notes
(*) See full text of phrases under section 16 and occupational Exposure Limit(s), if available, are listed in section 8
3.
Hazards identification
Harmful
Flammable. Harmful by inhalation. May cause sensitization by skin contact.
4.
General
: In all cases of doubt, or when symptoms persist, seek medical attention. Never
give anything by mouth to an unconscious person.
Remove to fresh air. Keep person warm and at rest. If not breathing, if breathing is
irregular or if respiratory arrest occurs, provide artificial respiration or oxygen by
trained personnel. Give nothing by mouth. If unconscious, place in recovery
position and seek medical advice.
Check for and remove any contact lenses. Immediately flush eyes with plenty of
water for at least 15 minutes, occasionally lifting the upper and lower eyelids. In all
cases of doubt, or when symptoms persist, seek medical attention.
Remove contaminated clothing and shoes. Wash skin thoroughly with soap and
water or use recognized skin cleanser. Do not use solvents or thinners.
Inhalation
Eye Contact
Skin Contact
Date of issue
: 8/16/2006.
Page: 1/5
9537000000
: If swallowed, seek medical advice immediately and show this document. Keep
person warm and at rest. Do NOT induce vomiting unless directed to do so by
medical personnel. Lower the head so that the vomit will not reenter the mouth
and throat.
Notes to physician
: If gasses have been inhaled, from the decomposition of the product, symptoms
may be delayed.
5.
Fire-fighting measures
Fire will produce dense black smoke. Exposure to decomposition products may cause a health hazard. Fire-fighters
should wear appropriate protective equipment. Cool closed containers exposed to fire with water. Do not release
runoff from fire to sewers or waterways.
Extinguishing Media
: Recommended: alcohol resistant foam, CO2, powders, water spray.
Not to be used : waterjet.
Fire Degradation Products
: These products are carbon oxides (CO, CO2), nitrogen oxides (NO, NO2 etc.).
6.
Exclude sources of ignition and be aware of explosion hazard. Ventilate the area.
Avoid all direct contact with the spilled material. Avoid breathing vapor or mist. Refer to protective measures listed in
sections 7 and 8.
Contain and collect spillage with non-combustible absorbent materials, e.g. sand, earth, vermiculite, diatomaceous
earth, and place in container for disposal according to local regulations (see section 13). Do not allow to enter drains
or watercourses. Clean preferably with a detergent; avoid use of solvents. If the product contaminates lakes, rivers, or
sewers, inform the appropriate authorities in accordance with local regulation.
7.
Handling
Vapors are heavier than air and may spread along floors. Vapors may form explosive mixtures with air. Prevent the
creation of flammable or explosive concentrations of vapors in air and avoid vapor concentrations higher than the
occupational exposure limits. In addition, the product should be used only in areas from which all naked lights and
other sources of ignition have been excluded. Electrical equipment should be protected to the appropriate standard.
To dissipate static electricity during transfer, ground drum and connect to receiving container with bonding strap. No
sparking tools should be used.
Care should be taken when re-opening partly-used containers.
Avoid inhalation of vapour, dust and spray mist. Avoid contact with skin and eyes. Eating, drinking and smoking should
be prohibited in area where this material is handled, stored and processed. Appropriate personal protective
equipment: see Section 8. Always keep in containers made from the same material as the original one.
Storage
Store in accordance with local regulations for flammable liquids. Observe label precautions. Store in a cool, wellventilated area away from incompatible materials and ignition sources. Keep out of the reach of children.
Keep away from: Oxidizing agents, strong alkalis, strong acids as well as of amines, alcohols and water. No smoking.
Prevent unauthorized access. Containers that are opened must be carefully resealed and kept upright to prevent
leakage.
8.
Engineering measures
Hygiene measures
Ingredient Name
2-methoxy-1-methylethyl acetate
xylene
ethylbenzene
Date of issue
: 8/16/2006.
Page: 2/5
9537000000
STEL: 200 ppm 15 minute/minutes. Form: All forms
TWA: 442 mg/m3 8 hour/hours. Form: All forms
TWA: 100 ppm 8 hour/hours. Form: All forms
hexamethylene-di-isocyanate
: Gloves must be worn for all work that may result in soiling.
Hands
: Wear suitable gloves. Barrier creams may help to protect the exposed areas of
Respiratory system
Eyes
9.
the skin, but should not be applied once exposure has occurred. Barrier creams
may not be used under or instead of gloves.
It is not possible to specify precise type of gloves, since the actual work situation
is unknown. Supplier of gloves should be contacted in order to find the appropriate
type.
Use safety eyewear designed to protect against splash of liquids.
Physical state
Density
: Liquid.
: -67.17C based on data for: prepolymer isocyanate HDI
: 1.06 to 1.08 g/cm3
Solubility
Flash point
Explosion Limits
:
:
:
:
:
:
Melting Point
% Solvent by Weight
% Water by Weight
VOC Content
TOC Content
Solvent Gas
1 - 10.8 vol %
Weighted average: 25 %
Weighted average: 0 %
Weighted average: 273 g/l (CEPE)
Weighted average: 197 g/l (based on data for: Solvent.)
0.055 m 3/l
Date of issue
: 8/16/2006.
Page: 3/5
9537000000
Exposure to component solvent vapor concentrations may result in adverse health effects such as mucous membrane
and respiratory system irritation and adverse effects on the kidneys, liver and central nervous system. Solvents may
cause some of the above effects by absorption through the skin. Symptoms and signs include headaches, dizziness,
fatigue, muscular weakness, drowsiness and, in extreme cases, loss of consciousness. Repeated or prolonged
contact with the preparation may cause removal of natural fat from the skin, resulting in non-allergic contact dermatitis
and absorption through the skin. If splashed in the eyes, the liquid may cause irritation and reversible damage.
Accidental swallowing may cause stomach pain. Chemical lung inflammation may occur if the product is taken into the
lungs via vomiting.
Isocyanate containing products have characteristics that include producing acute irritation and/or sensitisation when
breathing, subsequent asthmatic problems and lung contractions. Sensitised people can, as a result from this, show
asthmatic symptoms with exposure to atmospheric concentrations far below the TLV. Repeated exposures will lead to
permanent damage to the respiratory system.
Sensitization
Acute toxicity
Ingredient Name
Test
Result
Route
Species
LD50
LD50
LD50
LD50
LDLo
LC50
LD50
LD50
LD50
LC50
350 mg/kg
8532 mg/kg
4300 mg/kg
>1700 mg/kg
50 mg/kg
>6700 ppm (4 hour/hours)
3500 mg/kg
738 mg/kg
593 mg/kg
0.06 mg/l (4 hour/hours)
Oral
Oral
Oral
Dermal
Oral
Inhalation
Oral
Oral
Dermal
Inhalation
Mouse
Rat
Rat
Rabbit
Human
Rat
Rat
Rat
Rabbit
Rat
ethylbenzene
hexamethylene-di-isocyanate
Species
Period
Result
xylene
ethylbenzene
96 hour/hours
48 hour/hours
48 hour/hours
96 hour/hours
8.2 mg/l
2.93 mg/l
7.2 mg/l
9.09 mg/l
UN1263
Class
PG*
III
Label
Additional information
Remarks
H-14
IMDG
Class
UN1263
PAINT
Emergency schedules
(EmS)
III
3
F-E, S-E
Date of issue
: 8/16/2006.
Page: 4/5
9537000000
Safety Phrases
Other EU Regulations
Classification and labeling have been performed according to EU Directives 67/548/EEC and 1999/45/EC (including
amendments) and the intended use.
- Consumer applications, Industrial applications, Used by spraying.
Tactile warning of danger
: Yes, applicable.
Notice to Reader
Modified data or content compared with the previous version are maked with a triangular marker in the upper-left
corner within the Safety Data Sheet.
The information contained in this safety data sheet is based on the present state of knowledge and EU and national
legislation. It provides guidance on health, safety and environmental aspects for handling the product in a safe way
and should not be construed as any guarantee of the technical preformance or suitability for particular applications.
It is always the duty of the user/employer to ascertain that the work is planned and carried out in accordance with the
national regulations.
Date of issue
: 8/16/2006.
Page: 5/5
Product Type
:
:
:
:
Field of application
Date of issue
Date of Previous Issue
2.
9588100000
Hempel A/S
Lundtoftevej 150
DK-2800 Kgs. Lyngby
Denmark
Tel.: + 45 45 93 38 00
Emergency phone:
+45 45 93 38 00
See section 4 First aid
measures.
Composition/information on ingredients
Substances presenting a health or environmental hazard within the meaning of the Dangerous Substances Directive
67/548/EEC.
Ingredient Name
CAS No.
EC Number
Classification
xylene
1330-20-7
30 - 40
215-535-7
ethylbenzene
100-41-4
5 - 10
202-849-4
triethylenetetramine
112-24-3
1-3
203-950-6
di-isobutyl ketone
108-83-8
1-3
203-620-1
R10
Xn; R20/21
Xi; R38
F; R11
Xn; R20
Xn; R21
C; R34
R43
R52/53
R10
Xi; R37
.
Notes
(*) See full text of phrases under section 16 and occupational Exposure Limit(s), if available, are listed in section 8
3.
Hazards identification
Harmful
Flammable. Harmful by inhalation and in contact with skin. May cause sensitization by skin contact. Irritating to skin.
4.
General
: In all cases of doubt, or when symptoms persist, seek medical attention. Never
give anything by mouth to an unconscious person.
Remove to fresh air. Keep person warm and at rest. If not breathing, if breathing is
irregular or if respiratory arrest occurs, provide artificial respiration or oxygen by
trained personnel. Give nothing by mouth. If unconscious, place in recovery
position and seek medical advice.
Check for and remove any contact lenses. Immediately flush eyes with plenty of
water for at least 15 minutes, occasionally lifting the upper and lower eyelids. In all
cases of doubt, or when symptoms persist, seek medical attention.
Remove contaminated clothing and shoes. Wash skin thoroughly with soap and
water or use recognized skin cleanser. Do not use solvents or thinners.
Inhalation
Eye Contact
Skin Contact
Date of issue
: 21-08-2006.
Page: 1/5
9588100000
: If swallowed, seek medical advice immediately and show this document. Keep
person warm and at rest. Do NOT induce vomiting unless directed to do so by
medical personnel. Lower the head so that the vomit will not reenter the mouth
and throat.
Notes to physician
: If gasses have been inhaled, from the decomposition of the product, symptoms
may be delayed.
5.
Fire-fighting measures
Fire will produce dense black smoke. Exposure to decomposition products may cause a health hazard. Fire-fighters
should wear appropriate protective equipment. Cool closed containers exposed to fire with water. Do not release
runoff from fire to sewers or waterways.
Extinguishing Media
: Recommended: alcohol resistant foam, CO2, powders, water spray.
Not to be used : waterjet.
Fire Degradation Products
: These products are carbon oxides (CO, CO2), nitrogen oxides (NO, NO2 etc.).
6.
Exclude sources of ignition and be aware of explosion hazard. Ventilate the area.
Avoid all direct contact with the spilled material. Avoid breathing vapor or mist. Refer to protective measures listed in
sections 7 and 8.
Contain and collect spillage with non-combustible absorbent materials, e.g. sand, earth, vermiculite, diatomaceous
earth, and place in container for disposal according to local regulations (see section 13). Do not allow to enter drains
or watercourses. Clean preferably with a detergent; avoid use of solvents. If the product contaminates lakes, rivers, or
sewers, inform the appropriate authorities in accordance with local regulation.
7.
Handling
Vapors are heavier than air and may spread along floors. Vapors may form explosive mixtures with air. Prevent the
creation of flammable or explosive concentrations of vapors in air and avoid vapor concentrations higher than the
occupational exposure limits. In addition, the product should be used only in areas from which all naked lights and
other sources of ignition have been excluded. Electrical equipment should be protected to the appropriate standard.
To dissipate static electricity during transfer, ground drum and connect to receiving container with bonding strap. No
sparking tools should be used.
Avoid inhalation of vapour, dust and spray mist. Avoid contact with skin and eyes. Eating, drinking and smoking should
be prohibited in area where this material is handled, stored and processed. Appropriate personal protective
equipment: see Section 8. Always keep in containers made from the same material as the original one.
Storage
Store in accordance with local regulations for flammable liquids. Observe label precautions. Store in a cool, wellventilated area away from incompatible materials and ignition sources. Keep out of the reach of children.
Keep away from: Oxidizing agents, strong alkalis, strong acids. No smoking. Prevent unauthorized access. Containers
that are opened must be carefully resealed and kept upright to prevent leakage.
8.
Engineering measures
Hygiene measures
Ingredient Name
xylene
ethylbenzene
di-isobutyl ketone
Date of issue
: 21-08-2006.
Page: 2/5
9588100000
: Gloves must be worn for all work that may result in soiling.
Hands
: Wear suitable gloves. Barrier creams may help to protect the exposed areas of
Respiratory system
Eyes
9.
the skin, but should not be applied once exposure has occurred. Barrier creams
may not be used under or instead of gloves.
It is not possible to specify precise type of gloves, since the actual work situation
is unknown. Supplier of gloves should be contacted in order to find the appropriate
type.
Use safety eyewear designed to protect against splash of liquids.
Physical state
Density
: Liquid.
: 0.944 g/cm3
Solubility
Flash point
Explosion Limits
:
:
:
:
:
:
% Solvent by Weight
% Water by Weight
VOC Content
TOC Content
Solvent Gas
1 - 7.6 vol %
Weighted average: 40 %
Weighted average: 0 %
Weighted average: 378 g/l (CEPE)
Weighted average: 342 g/l (based on data for: Solvent.)
0.085 m 3/l
Acute toxicity
Ingredient Name
Date of issue
Test
: 21-08-2006.
Result
Route
Species
Page: 3/5
9588100000
xylene
LD50
LD50
LDLo
LC50
LD50
LD50
LD50
LD50
LD50
ethylbenzene
triethylenetetramine
di-isobutyl ketone
4300 mg/kg
>1700 mg/kg
50 mg/kg
>6700 ppm (4 hour/hours)
3500 mg/kg
2500 mg/kg
805 mg/kg
5750 mg/kg
16000 mg/kg
Oral
Dermal
Oral
Inhalation
Oral
Oral
Dermal
Oral
Dermal
Rat
Rabbit
Human
Rat
Rat
Rat
Rabbit
Rat
Rabbit
Species
Period
Result
xylene
ethylbenzene
96 hour/hours
48 hour/hours
48 hour/hours
96 hour/hours
8.2 mg/l
2.93 mg/l
7.2 mg/l
9.09 mg/l
UN1263
Class
PG*
III
Label
Additional information
Remarks
H-14
IMDG
Class
UN1263
PAINT
Emergency schedules
(EmS)
III
3
F-E, S-E
: xylene
Risk Phrases
Safety Phrases
triethylenetetramine
R10- Flammable.
R20/21- Harmful by inhalation and in contact with skin.
R38- Irritating to skin.
R43- May cause sensitization by skin contact.
S23- Do not breathe vapour/spray.
S36/37- Wear suitable protective clothing and gloves.
S51- Use only in well-ventilated areas.
Other EU Regulations
Classification and labeling have been performed according to EU Directives 67/548/EEC and 1999/45/EC (including
amendments) and the intended use.
- Industrial applications, Used by spraying.
Date of issue
: 21-08-2006.
Page: 4/5
9588100000
Notice to Reader
Modified data or content compared with the previous version are maked with a triangular marker in the upper-left
corner within the Safety Data Sheet.
The information contained in this safety data sheet is based on the present state of knowledge and EU and national
legislation. It provides guidance on health, safety and environmental aspects for handling the product in a safe way
and should not be construed as any guarantee of the technical preformance or suitability for particular applications.
It is always the duty of the user/employer to ascertain that the work is planned and carried out in accordance with the
national regulations.
Date of issue
: 21-08-2006.
Page: 5/5
Product Type
:
:
:
:
:
Field of application
Ready for use mixture
Date of issue
Date of Previous Issue
2.
9704000000
Hempel A/S
Lundtoftevej 150
DK-2800 Kgs. Lyngby
Denmark
Tel.: + 45 45 93 38 00
Emergency phone:
+45 45 93 38 00
See section 4 First aid
measures.
curing agent
metal industry, ships and shipyards.
17369 8 LI / 97040 2 LI
09-02-2006.
12-12-2005.
Composition/information on ingredients
Substances presenting a health or environmental hazard within the meaning of the Dangerous Substances Directive
67/548/EEC.
Ingredient Name
CAS No.
EC Number
Classification
xylene
1330-20-7
15 - 20
215-535-7
1-methoxy-2-propanol
2,4,6-tris(dimethylaminomethyl)phenol
107-98-2
90-72-2
12.5 - 15
5 - 10
203-539-1
202-013-9
ethylbenzene
100-41-4
3-5
202-849-4
triethylenetetramine
112-24-3
1-3
203-950-6
R10
Xn; R20/21
Xi; R38
R10
Xn; R22
Xi; R36/38
F; R11
Xn; R20
Xn; R21
C; R34
R43
R52/53
.
Notes
(*) See full text of phrases under section 16 and occupational Exposure Limit(s), if available, are listed in section 8
3.
Hazards identification
Harmful
Flammable. Harmful by inhalation and in contact with skin. May cause sensitization by skin contact. Irritating to skin.
4.
General
: In all cases of doubt, or when symptoms persist, seek medical attention. Never
give anything by mouth to an unconscious person.
Move the person into fresh air and keep the person under surveillance. Keep
person warm and at rest. If not breathing, if breathing is irregular or if respiratory
arrest occurs, provide artificial respiration or oxygen by trained personnel. Give
nothing by mouth. If unconscious, place in recovery position and seek medical
advice.
Inhalation
Date of issue
: 09-02-2006.
Page: 1/5
9704000000
: Check for and remove any contact lenses. Immediately flush eyes with plenty of
water for at least 15 minutes, occasionally lifting the upper and lower eyelids. In all
cases of doubt, or when symptoms persist, seek medical attention.
Remove contaminated clothing and shoes. Wash skin thoroughly with soap and
water or use recognized skin cleanser. Do not use solvents or thinners.
Skin Contact
Ingestion
: If swallowed, seek medical advice immediately and show this document. Keep
Notes to physician
5.
Fire-fighting measures
Fire will produce dense black smoke. Exposure to decomposition products may cause a health hazard. Fire-fighters
should wear appropriate protective equipment. Cool closed containers exposed to fire with water. Do not release
runoff from fire to sewers or waterways.
Extinguishing Media
: Recommended: alcohol resistant foam, CO2, powders, water spray.
Not to be used : waterjet.
Fire Degradation Products
: These products are carbon oxides (CO, CO2), nitrogen oxides (NO, NO2 etc.).
6.
Exclude sources of ignition and be aware of explosion hazard. Ventilate the area.
Avoid all direct contact with the spilled material. Avoid breathing vapor or mist. Refer to protective measures listed in
sections 7 and 8.
Contain and collect spillage with non-combustible absorbent materials, e.g. sand, earth, vermiculite, diatomaceous
earth, and place in container for disposal according to local regulations (see section 13). Do not allow to enter drains
or watercourses. Clean preferably with a detergent; avoid use of solvents. If the product contaminates lakes, rivers, or
sewers, inform the appropriate authorities in accordance with local regulation.
7.
Handling
Vapors are heavier than air and may spread along floors. Vapors may form explosive mixtures with air. Prevent the
creation of flammable or explosive concentrations of vapors in air and avoid vapor concentrations higher than the
occupational exposure limits. In addition, the product should be used only in areas from which all naked lights and
other sources of ignition have been excluded. Electrical equipment should be protected to the appropriate standard.
To dissipate static electricity during transfer, ground drum and connect to receiving container with bonding strap. No
sparking tools should be used.
Avoid inhalation of vapour, dust and spray mist. Avoid contact with skin and eyes. Eating, drinking and smoking should
be prohibited in area where this material is handled, stored and processed. Appropriate personal protective
equipment: see Section 8. Always keep in containers made from the same material as the original one.
Storage
Store in accordance with local regulations for flammable liquids. Observe label precautions. Store in a cool, wellventilated area away from incompatible materials and ignition sources. Keep out of the reach of children.
Keep away from: Oxidizing agents, strong alkalis, strong acids. No smoking. Prevent unauthorized access. Containers
that are opened must be carefully resealed and kept upright to prevent leakage.
8.
Engineering measures
Hygiene measures
Date of issue
: 09-02-2006.
Page: 2/5
9704000000
Ingredient Name
xylene
1-methoxy-2-propanol
ethylbenzene
: Gloves must be worn for all work that may result in soiling.
Hands
: Wear suitable gloves. Barrier creams may help to protect the exposed areas of
Respiratory system
Eyes
9.
the skin, but should not be applied once exposure has occurred. Barrier creams
may not be used under or instead of gloves.
It is not possible to specify precise type of gloves, since the actual work situation
is unknown. Supplier of gloves should be contacted in order to find the appropriate
type.
Use safety eyewear designed to protect against splash of liquids.
Physical state
Density
: Liquid.
: Weighted average: 0.96 g/cm 3
Solubility
Flash point
Explosion Limits
:
:
:
:
:
:
% Solvent by Weight
% Water by Weight
VOC Content
TOC Content
Solvent Gas
1 - 13.1 vol %
Weighted average: 37 %
Weighted average: 0 %
Weighted average: 351 g/l (CEPE)
Weighted average: 267 g/l (based on data for: Solvent.)
0.085 m 3/l
Date of issue
: 09-02-2006.
Page: 3/5
9704000000
Acute toxicity
Ingredient Name
Test
Result
Route
Species
xylene
LD50
LD50
LDLo
LC50
LD50
LDLo
LD50
LD50
LD50
LD50
LD50
4300 mg/kg
>1700 mg/kg
50 mg/kg
>6700 ppm (4 hour/hours)
5700 mg/kg
3739 mg/kg
1200 mg/kg
1280 mg/kg
3500 mg/kg
2500 mg/kg
805 mg/kg
Oral
Dermal
Oral
Inhalation
Oral
Oral
Oral
Dermal
Oral
Oral
Dermal
Rat
Rabbit
Human
Rat
Rabbit
Rat
Rat
Rat
Rat
Rat
Rabbit
1-methoxy-2-propanol
2,4,6-tris(dimethylaminomethyl)phenol
ethylbenzene
triethylenetetramine
Species
Period
Result
xylene
ethylbenzene
96 hour/hours
48 hour/hours
48 hour/hours
96 hour/hours
8.2 mg/l
2.93 mg/l
7.2 mg/l
9.09 mg/l
UN1263
Class
PG*
III
Label
Additional information
Remarks
H-14
IMDG
Class
UN1263
PAINT
Emergency schedules
(EmS)
III
3
F-E, S-E
Date of issue
: 09-02-2006.
Page: 4/5
9704000000
: xylene
Risk Phrases
Safety Phrases
triethylenetetramine
R10- Flammable.
R20/21- Harmful by inhalation and in contact with skin.
R38- Irritating to skin.
R43- May cause sensitization by skin contact.
S23- Do not breathe vapor/spray.
S36/37- Wear suitable protective clothing and gloves.
S51- Use only in well-ventilated areas.
Other EU Regulations
Classification and labeling have been performed according to EU Directives 67/548/EEC and 1999/45/EC (including
amendments) and the intended use.
- Industrial applications, Used by spraying.
Notice to Reader
Modified data or content compared with the previous version are maked with a triangular marker in the upper-left
corner within the Safety Data Sheet.
The information contained in this safety data sheet is based on the present state of knowledge and EU and national
legislation. It provides guidance on health, safety and environmental aspects for handling the product in a safe way
and should not be construed as any guarantee of the technical preformance or suitability for particular applications.
It is always the duty of the user/employer to ascertain that the work is planned and carried out in accordance with the
national regulations.
Date of issue
: 09-02-2006.
Page: 5/5
APPLICATION INSTRUCTION
INDUSTRIAL SERVICES
OFFSHORE SERVICES
MARINE SERVICES
Mechanical, Electrical, Piping, Steel Structure , Pressure Vessel Fabrication & Installation.
Oil & Gas Engineering, Offshore Constructions & Maintenance.
Ship Construction, Ship Repair.
Application
Application Instructions
Instructions
For product description refer to product data sheet
HEMPADURMASTIC 45880/
HEMPADURMASTIC 45881
High temperatures: 45881: BASE 45889 with CURING AGENT 95881
Low to medium temperatures: 45880: BASE 45889 with CURING AGENT 95880
Scope:
Surface preparation:
Page 1 of 6
HEMPEL
HEMPEL
Application
Instructions
Application Instructions
HEMPADUR MASTIC 45880/45881 being a high solids and a relatively high viscosity
material, may require special measures to be taken at application.
Recommended airless spray equipment:
Pump ratio:
Pump output:
min. 45:1
12 litres/minute (theoretical)
Input pressure:
Spray hoses:
Regular surfaces:
Nozzle size:.021" through .023"
Fan angle: 60.
After finishing the application, clean the equipment immediately with THINNER 08450 or
HEMPELS TOOL CLEANER 99610.
Note: Increasing hose diameter may increase paint flow, thereby improving the spray
fan. If longer hoses are necessary it may be necessary to raise the pump ratio to 60:1,
maintaining the high output capacity of the pump.
Alternatively up to approx. 5% THINNER 08450 may be added, but thinning must be
done with care as the anti-sagging properties are drastically reduced by overthinning.
Airless spray data are indicative and subject to adjustment.
Induction time:
Page 2 of 6
Application Instructions
At application with hand tools, brush, but especially by roller the natural tendency to a
more uneven paint film obtained by these methods, is to be counteracted by more
coats applied. If at all possible each coat is to be applied across the preceding one - in
general follow good painting practise.
On poorly prepared surfaces it is always recommended to apply the first coat by brush.
Extra thinning will facilitate the penetration of the paint material, but will also require an
extra layer to be applied.
Please note that the thixotropic nature of HEMPADUR MASTIC 45880/45881 may give
a rather "wavy" surface of the paint just after application. This smoothens at drying, but
can make it necessary to let the wet film readings be of a higher value than indicated.
In many cases the wet film thickness, reading should be 25-50 micron/1-2 mils higher
than calculated. As the wavy surface becomes more smooth during drying these extra
wet film thickness readings will not cause a higher paint consumption than otherwise
stipulated.
Film thickness/thinning:
Pot life:
When measured under standard conditions the pot life is 1 hour at 20C/68F for
HEMPADUR MASTIC 45880 respectively 1 hours at 30C/86F for HEMPADUR
MASTIC 45881. However, for a 20 litres/5 US gallons mix, and used under warm
climate conditions, the heat developed by the chemical reaction between BASE and
CURING AGENT may make the corresponding practical pot life shorter.
Therefore: At high temperatures, use the paint immediately after mixing irrespective of
equipment.
Attached:
Page 3 of 6
Application Instructions
Drying time and recoating interval vary with film thickness, temperature and later
exposure conditions:
HEMPADUR MASTIC 45880 in a dry film thickness of 100-150 micron/4-6 mils:
Surface temperature:
-5C/23F
3 days
2 months
12 hours
14 days
4 hours
7 days
3 hours
5 days
2 hours
3 days
5 hours
7 hours
8 hours
4 hours
5 hours
6 hours
3 hours
4 hours
5 hours
Atmospheric, medium
Atmospheric, severe
15 hours
15 hours
5 hours
5 hours
4 hours
4 hours
3 hours
3 hours
12 hours
18 hours
5 hours
7 hours
4 hours
5 hours
3 hours
4 hours
3 days
3 days
45 hours
45 hours
N/R
N/R
N/R
N/R
-5C/23F
6 days
2 months
18 hours
14 days
6 hours
7 days
5 hours
5 days
4 hours
3 days
21 hours
30 hours
36 hours
7 hours
10 hours
12 hours
5 hours
8 hours
9 hours
4 hours
6 hours
7 hours
Atmospheric, medium
Atmospheric, severe
21 hours
21 hours
7 hours
7 hours
5 hours
5 hours
4 hours
4 hours
21 hours
30 hours
7 hours
10 hours
5 hours
8 hours
4 hours
6 hours
5 days
5 days
63 hours
63 hours
N/R
N/R
N/R
N/R
Notes:
Avoid sudden drops in (substrate) temperatures during drying/initial curing. It is especially important that the
substrate temperature does not drop significantly before application of the acrylic or polyurethane finish and
that proper ventilation is maintained.
If faster handling or recoating at lower temperatures is required, HEMPADUR 45143 may be used.
In case of low temperatures, it is recommended that HEMPADUR MASTIC 45880 has been given a proper
induction time before application. Under such conditions, consider paint temperature equal to substrate
temperature and follow the rules given on page 2.
Page 4 of 6
Application Instructions
-5C/23F
40C/104F
Extended*
Extended*
23 days
Extended*
Extended*
15 days
Extended*
Extended*
Extended*
Extended*
9 hours
9 hours
6 hours
6 hours
12 hours
12 hours
Atmospheric, medium
N/R
N/R
9 days
3 days
2 days
36 hours
1 days
1 day
Atmospheric, severe
N/R
N/R
4 days
18 hours
1. Depending on actual local conditions, extended maximum recoating intervals may apply.
Please contact Hempel for further advice.
Notes:
Avoid sudden drops in (substrate) temperatures during drying/initial curing.
If faster handling is required at low temperatures, HEMPADUR 45143 may be used.
20C/68F
4 hours
7 days
30C/86F 40C/104F
3 hours
5 days
2 hours
3 days
5 hours
7 hours
8 hours
4 hours
6 hours
6 hours
3 hours
4 hours
5 hours
20C/68F
6 hours
7 days
30C/86F 40C/104F
5 hours
5 days
4 hours
3 days
7 hours
10 hours
12 hours
6 hours
8 hours
10 hours
4 hours
6 hours
8 hours
20C/68F
30C/86F 40C/104F
Extended*
Extended*
1 months
Extended*
Extended*
23 days
Extended*
Extended*
15 days
Extended*
Extended*
Extended*
Extended*
Extended*
Extended*
12 hours
9 hours
6 hours
3 days
1 days
2 days
1 day
1 day
12 hours
Page 5 of 6
Application Instructions
Handle with care. Before and during use, observe all safety labels on packaging and
paint containers, consult HEMPEL Material Safety Data Sheets and follow all local or
national safety regulations. Avoid inhalation, avoid contact with skin and eyes, and do
not swallow. Take precautions against possible risks of fire or explosions as well as
protection of the environment. Apply only in well ventilated areas.
ISSUED BY:
Page 6 of 6
Application Instructions
INDUSTRIAL SERVICES
OFFSHORE SERVICES
MARINE SERVICES
Mechanical, Electrical, Piping, Steel Structure , Pressure Vessel Fabrication & Installation.
Oil & Gas Engineering, Offshore Constructions & Maintenance.
Ship Construction, Ship Repair.
HMP Colour
RAL
RAL
RAL
RAL
RAL
RAL
RAL
RAL
RAL
RAL
RAL
RAL
RAL
RAL
RAL
RAL
RAL
RAL
RAL
RAL
RAL
RAL
RAL
RAL
RAL
RAL
RAL
RAL
RAL
RAL
RAL
RAL
RAL
RAL
RAL
RAL
RAL
RAL
RAL
RAL
RAL
RAL
RAL
RAL
RAL
RAL
RAL
RAL
RAL
RAL
RAL
RAL
RAL
RAL
RAL
RAL
22500
24900
20470
27030
27040
27050
20820
27070
27110
23120
17130
20420
27150
27160
27170
27180
27190
27200
20250
27230
27240
27260
27270
27280
27320
27330
27340
19350
27370
22120
50060
57020
57030
50190
50180
57070
57080
57090
57100
57110
57120
59130
50170
57150
50740
51710
50100
51800
57370
53090
57310
57320
57330
57340
57350
57460
1000
1001
1002
1003
1004
1005
1006
1007
1011
1012
1013
1014
1015
1016
1017
1018
1019
1020
1021
1023
1024
1026
1027
1028
1032
1033
1034
1035
1037
2000
2001
2002
2003
2004
2005
2007
2008
2009
2010
2011
2012
2013
3000
3001
3002
3003
3004
3005
3007
3009
3011
3012
3013
3014
3015
3016
22506
24906
20476
27036
27046
27056
20826
27076
27116
23126
17136
20426
27156
27166
27176
27186
27196
27206
20256
27236
27246
27266
27276
27286
27326
27336
27346
19356
27376
22126
50066
57026
57036
50196
50186
57076
57086
57096
57106
57116
57126
59136
50176
57156
50746
51716
50106
51806
57376
53096
57316
57326
57336
57346
57356
57466
RAL
RAL
RAL
RAL
RAL
RAL
RAL
RAL
RAL
RAL
RAL
RAL
RAL
RAL
RAL
RAL
RAL
RAL
RAL
RAL
RAL
RAL
RAL
RAL
RAL
RAL
RAL
RAL
RAL
RAL
RAL
RAL
RAL
RAL
RAL
RAL
RAL
RAL
RAL
RAL
RAL
RAL
RAL
RAL
RAL
RAL
RAL
RAL
RAL
RAL
RAL
RAL
RAL
RAL
RAL
RAL
RAL
HMP Colour
3017
3018
3020
3022
3024
3026
3027
3031
4001
4002
4003
4004
4005
4006
4007
4008
4009
4010
4012
5000
5001
5002
5003
5004
5005
5007
5008
5009
5010
5011
5012
5013
5014
5015
5017
5018
5019
5020
5021
5022
5023
5024
6000
6001
6002
6003
6004
6005
6006
6007
6008
6009
6010
6011
6012
6013
57470
57480
57200
57520
57540
50090
57570
57410
37010
57620
57630
57640
37050
57660
57670
57680
57690
57700
38120
37000
37020
30170
37030
37040
37150
30570
32080
32090
30180
37110
35120
33930
37140
37240
37170
45180
30350
45200
40210
37220
37230
37440
46000
40050
47020
47030
41490
47050
47060
47070
47080
47090
40220
40840
47120
41130
57476
57486
57206
57526
57546
50096
57576
57416
37016
57626
57636
57646
37056
57666
57676
57686
57696
57706
38126
37006
37026
30176
37036
37046
37156
30576
32086
32096
30186
37116
35126
33936
37146
37246
37176
45186
30356
45206
40216
37226
37236
37446
46006
40056
47026
47036
41496
47056
47066
47076
47086
47096
40226
40846
47126
41136
RAL
HMP Colour
RAL
RAL
RAL
RAL
RAL
RAL
RAL
RAL
RAL
RAL
RAL
RAL
RAL
RAL
RAL
RAL
RAL
RAL
RAL
RAL
RAL
RAL
RAL
RAL
RAL
RAL
RAL
RAL
RAL
RAL
RAL
RAL
RAL
RAL
RAL
RAL
RAL
RAL
RAL
RAL
RAL
RAL
RAL
RAL
RAL
RAL
RAL
RAL
RAL
RAL
RAL
RAL
RAL
RAL
RAL
RAL
6014
6015
6016
6017
6018
6019
6020
6021
6022
6024
6025
6026
6027
6028
6029
6032
6033
6034
7000
7001
7002
7003
7004
7005
7006
7008
7009
7010
7011
7012
7013
7015
7016
7021
7022
7023
7024
7026
7030
7031
7032
7033
7034
7035
7036
7037
7038
7039
7040
7042
7043
7044
7045
7046
7047
7048
47140
47150
47160
42600
42170
49500
47200
47210
47220
47240
47250
47260
47270
47280
47290
47320
47330
47340
10390
10400
17020
17030
17160
17040
17060
17080
17100
17110
17120
10270
17530
10380
10520
17210
17220
13230
17240
17260
17300
17310
11320
17330
17340
11150
11730
11370
17380
17390
17700
17720
17730
17740
17750
17860
17770
17480
47146
47156
47166
42606
42176
49506
47206
47216
47226
47246
47256
47266
47276
47286
47296
47326
47336
47346
10396
10406
17026
17036
17166
17046
17066
17086
17106
17116
17126
10276
17536
10386
10526
17216
17226
13236
17246
17266
17306
17316
11326
17336
17346
11156
11736
11376
17386
17396
17706
17726
17736
17746
17756
17866
17776
17486
HEMPEL
Edition: 10/2004, R&D Colour Management
Page: 1 of 2
HMP Colour
RAL
RAL
RAL
RAL
RAL
RAL
RAL
RAL
RAL
RAL
RAL
RAL
RAL
RAL
RAL
RAL
RAL
RAL
RAL
RAL
RAL
RAL
RAL
RAL
RAL
RAL
RAL
RAL
RAL
RAL
RAL
RAL
67000
67010
67020
67030
61810
67070
67080
67110
67120
67140
67150
60160
67170
60180
67220
67230
67240
67250
67280
20450
17620
17630
17940
19990
19000
19870
10170
17910
17760
17970
17980
19230
8000
8001
8002
8003
8004
8007
8008
8011
8012
8014
8015
8016
8017
8019
8022
8023
8024
8025
8028
9001
9002
9003
9004
9005
9006
9007
9010
9011
9016
9017
9018
9023
RAL
HMP Colour
RAL
HMP Colour
67006
67016
67026
67036
61816
67076
67086
67116
67126
67146
67156
60166
67176
60186
67226
67236
67246
67256
67286
20456
17626
17636
17946
19996
19006
19876
10176
17916
17766
17976
17986
19236
HEMPEL
Edition: 10/2004, R&D Colour Management
Page: 2 of 2
000
000
000
030
030
040
040
040
090
180
180
180
250
260
290
320
HMP Colour
15
35
80
30
40
50
50
60
80
50
70
70
80
50
30
40
00
00
00
45
60
60
70
40
60
40
20
30
15
40
40
05
19993
15940
14780
56500
56480
56570
56470
56590
22860
49640
49670
49690
32810
32790
32630
10360
RAL
HMP Colour
RAL
HMP Colour
19999
15946
14786
56506
56486
56576
56476
56596
22866
49646
49676
49696
32816
32796
32636
10366
HEMPEL
Edition: 11/2004, R&D Colour Management
Page: 1 of 1