Beruflich Dokumente
Kultur Dokumente
C3 Gateway Controller
Release:14.0
Publication:630-00610-01
Document status:Standard
Document release date:20 December 2014
Copyright 2000-2014 GENBAND. All rights reserved. Use of this documentation and its contents is subject to
the terms and conditions of the applicable end user or software license agreement, right to use notice, and all
relevant copyright protections.
GENBAND, the GENBAND corporate logo and tagline, and certain of GENBAND's product and solution names
are registered trademarks of GENBAND and its affiliates.
While the information in this document is believed to be accurate and reliable, except as otherwise expressly
agreed to in writing, GENBAND AND/OR ITS LICENSORS PROVIDES THIS DOCUMENT "AS IS" WITHOUT
WARRANTY OR CONDITION OF ANY KIND, EITHER EXPRESS OR IMPLIED. The information and/or products
described in this document are subject to change without notice.
THE INFORMATION CONTAINED HEREIN IS THE PROPERTY OF GENBAND OR ITS LICENSORS AND
MUST NOT BE DISCLOSED, OTHER THAN TO EMPLOYEES OF GENBAND OR CUSTOMERS WITH NEEDTO-KNOW, WITHOUT THE PRIOR WRITTEN CONSENT OF GENBAND OR ITS LICENSORS. THE
INFORMATION MUST NOT BE DISCLOSED TO SUBCONTRACTORS OR REGULATORY AUTHORITIES.
GENBAND MUST BE NOTIFIED OF ANY REQUEST OR ORDER FOR DISCLOSURE PRIOR TO SUCH
DISCLOSURE.
For access to the Document Center, log in through the Customer Support website at http://cust.genband.com.
Contents
New in this Document
Introduction
In this section:7
Scope of this Document7
Related Maintenance Documents7
Maintenance and Replacement Tasks for Legacy C3 Platforms8
Maintenance and Replacement Tasks for SUN-Based C3 Platforms8
Maintenance and Replacement Tasks for the C3 IA-RMS Platform9
GENBAND GENiUS Solution9
How to Contact Us10
20 December 2014
11
15
630-00610-01 12.01
4
Replacing the C3 Ethernet Card43
Adding C3 Memory Cards44
Replacing the C3 Alarm Interface Card45
Replacing the C3 Alarm Board47
20 December 2014
C3 Gateway Controller
Copyright 2000-2014 GENBAND. All Rights Reserved.
49
57
630-00610-01 12.01
Modifications
This document is being released in a new format in this release.
20 December 2014
630-00610-01 12.01
20 December 2014
C3 Gateway Controller
Copyright 2000-2014 GENBAND. All Rights Reserved.
630-00610-01 12.01
Introduction
This document presents hardware maintenance and replacement tasks for
the C3 Gateway Controller.
In this section:
20 December 2014
for the 8000 Media Gateway, refer to the 8000 Media Gateway
Maintenance and Repair Guide (630-00611-01)
630-00610-01 12.01
8Introduction
Netra 240
Netra 440
20 December 2014
C3 Gateway Controller
Copyright 2000-2014 GENBAND. All Rights Reserved.
630-00610-01 12.01
20 December 2014
630-00610-01 12.01
10Introduction
How to Contact Us
20 December 2014
Issue
Customer Support Issues
Customer Support Portal
Documentation/Software
Downloads
Contact
www.genband.com
+1.866.436.2263
+1.512.682.5200 (outside the
Continental US)
+1.972.461.4101 (Fax)
custsite@genband.com
docs@genband.com
C3 Gateway Controller
Copyright 2000-2014 GENBAND. All Rights Reserved.
630-00610-01 12.01
11
Note: The following procedure is for the 410, 510, 512, and 514 C3
platforms. Procedures for filter replacement and maintenance on Sun
Netra T2000, T5220, 240, and 440 platforms can be found at Sun
Microsystems website: http://www.sun.com/products-n-solutions/
hardware/docs/Servers/. In addition, procedures for the T2000 and
T5220 C3 platforms can be found in section Component Replacement
Procedures for T2000 and T5220 (page 49).
In this section:
20 December 2014
630-00610-01 12.01
Required Tools
The following tools are required for replacing or cleaning the filter:
The front panel assembly contains the filter for the C3 unit, as shown in
C3 Unit Front Panel Filter Assembly (page 12). Refer to the steps below
to remove, replace or clean the filter.
Step
Action
Loosen the two screws that secure the front panel and filter
assembly to the C3 unit. Refer to C3 Unit Front Panel Filter
Assembly (page 12) for screw locations.
Remove the filter from the backside of the panel. The figure
below shows the back of the C3 front panel.
C3 Unit Back Panel Filter Assembly
20 December 2014
C3 Gateway Controller
Copyright 2000-2014 GENBAND. All Rights Reserved.
630-00610-01 12.01
Attention
20 December 2014
630-00610-01 12.01
20 December 2014
C3 Gateway Controller
Copyright 2000-2014 GENBAND. All Rights Reserved.
630-00610-01 12.01
15
Note: The following procedures are for the 410, 510, 512, and 514 C3
platforms. Procedures for Sun T2000, T5220, Netra 240, and Netra 440
C3 platforms can be found at Sun Microsystems website: http://
www.sun.com/products-n-solutions/hardware/docs/Servers/. In
addition, procedures for the T2000 and T5220 C3 platforms can be
found in section Component Replacement Procedures for T2000 and
T5220 (page 49).
In this section:
20 December 2014
630-00610-01 12.01
Required Tools
Flat-blade screwdriver
No. 1 Phillips-head screwdriver
No. 2 Phillips-head screwdriver
Two dual-fan assemblies sit side-by-side behind the front panel filter
assembly. A single-fan assembly is located on the right front of the C3
product next to the dual-fan assemblies. Location of Front Fans (page 16)
shows the location of these fans. Refer to the following procedures to
replace the front dual or single-fan assemblies.
Location of Front Fans
Action
Remove the front panel filter assembly from the front of the C3
unit. Refer to the first steps of Replacing the C3 Front Panel
Filter (page 12).
Loosen the three captive screws that secure the fan assembly.
Refer to Dual-Fan Assembly (page 17) for screw location.
CAUTION
20 December 2014
C3 Gateway Controller
Copyright 2000-2014 GENBAND. All Rights Reserved.
630-00610-01 12.01
Pull the fan assembly free from the power plug but do not fully
remove from the C3 product until the fans have stopped.
Reinstall the front panel filter assembly that was removed in Step
1.
--End--
Dual-Fan Assembly (page 17) shows the screw location on the dual-fan
assembly.
Dual-Fan Assembly
20 December 2014
630-00610-01 12.01
Action
Remove the front panel filter assembly from the front of the C3
unit. Refer to the first steps of Replacing the C3 Front Panel
Filter (page 12).
Loosen the two (2) captive screws that secure the fan assembly.
Refer to Single-Fan Assembly (page 19) for screw location.
Pull the fan assembly free from the power plug and out of the C3
product.
Reinstall the front panel filter assembly that was removed in Step
1.
--End--
Single-Fan Assembly (page 19) shows the screw location on the front
single-fan assembly.
20 December 2014
C3 Gateway Controller
Copyright 2000-2014 GENBAND. All Rights Reserved.
630-00610-01 12.01
20 December 2014
630-00610-01 12.01
The C3 rear fan assembly is located at the rear left side of the C3 product.
The assembly contains its own grill structure as part of the assembly. The
fan assembly can be removed and replaced without removing the C3 unit
cover. Refer to the following steps to remove the rear fan assembly.
Step
Action
Loosen the captive screws that secure the fan assembly to the
C3 unit. (The exact number and location varies from model to
model.)
Loosen the screws that secure the fan(s) to the fan assembly
structure.
To install the rear fan assembly, gently slide the fan assembly in
until it comes in contact with the power connectors.
20 December 2014
C3 Gateway Controller
Copyright 2000-2014 GENBAND. All Rights Reserved.
630-00610-01 12.01
Model 510, 512, and 514 Rear Double-Fan Connectors (page 22) shows
the power connectors of rear double-fan assembly for Models 510, 512,
and 514.
20 December 2014
630-00610-01 12.01
20 December 2014
C3 Gateway Controller
Copyright 2000-2014 GENBAND. All Rights Reserved.
630-00610-01 12.01
Step
Action
Attention
Display the tape contents to verify that it was saved by typing the
following:
tar -lvf /dev/rmt/0
--End--
20 December 2014
Step
Action
630-00610-01 12.01
Attention
Use EMS system status to determine if the target node has the
active instance of OamCfg. If OamCfg is active on the target
node, use the EMS to switch OamCfg active status to a different
node.
From the EMS, inhibit any SS7 links that terminate on the target
node.
Attention
Verify SS7 links on other nodes are carrying the SS7 traffic
10
11
Turn off the A circuit breaker to the target node. Verify breaker
locations by labels at PDU for circuit breaker identification
12
Verify that the proper circuit breaker was turned off by monitoring
the EMS events. The target C3 unit should indicate loss of
redundant power for the target unit.
13
14
20 December 2014
C3 Gateway Controller
Copyright 2000-2014 GENBAND. All Rights Reserved.
630-00610-01 12.01
20 December 2014
630-00610-01 12.01
20 December 2014
C3 Gateway Controller
Copyright 2000-2014 GENBAND. All Rights Reserved.
630-00610-01 12.01
The C3 unit is supported by a shelf inside the chassis and is held securely
in place by eight screws (four in front, four in rear) as shown in Rear C3
Unit Screw Assemblies (page 27).
Rear C3 Unit Screw Assemblies
20 December 2014
630-00610-01 12.01
20 December 2014
Step
Action
Ensure that power has been removed from the PDU circuit
breakers. Refer to Shutting Down the C3 Unit (page 23).
Remove the four (4) screw assemblies from the rear of the C3
unit. Refer to Rear C3 Unit Screw Assemblies (page 27) to
locate the screws.
Remove the front panel filter assembly from the front of the C3
unit. Refer to the first steps of Replacing the C3 Front Panel
Filter (page 12).
Remove the four (4) Phillips head screws that secure the C3 unit
to the chassis in the front. Refer to Front C3 Unit Screw
Assemblies (page 28) to locate the four (4) screws.
Line the replacement C3 unit up with the four screw holes in the
front and rear of the shelf edge.
C3 Gateway Controller
Copyright 2000-2014 GENBAND. All Rights Reserved.
630-00610-01 12.01
Secure the front and rear of the C3 unit by replacing the eight (8)
screws removed earlier.
10
11
12
Turn on the circuit breaker for the replaced C3 unit. Note that
models 512 and 514 may take a minute or more to power up.
13
14
The following command will boot the affected node from the CD
to format the drive and install the OS:
ok> boot cdrom:b - osonly [ frompeer | [ fromip <IP>
via <router> ] ]
--End--
Three (3) power supplies are accessible from the rear of the C3 product.
Refer to the following steps to remove the power supply.
20 December 2014
Step
Action
Pull the white ejector tabs forward and slide the power supply out
of the rear opening. Refer to Ejector Tab Locations (page 30)
for the location of the ejector tabs.
630-00610-01 12.01
WARNING
Ejector Tab Locations (page 30) shows the location of the ejector tabs.
Ejector Tab Locations
In the model 510, 512, and 514 C3 units, the top cover does not need to be
removed. To gain access to the internal components, simply loosen the
two captive screws at the top rear of the unit and lift the lid.
20 December 2014
C3 Gateway Controller
Copyright 2000-2014 GENBAND. All Rights Reserved.
630-00610-01 12.01
20 December 2014
Step
Action
To reinstall the cover, align the cover holes over the C3 unit
holes and secure the screws that were removed in Step 1.
630-00610-01 12.01
--End--
A black plastic faceplate frames the CD-ROM, tape drive and alarm board
on the front left side of the C3 unit. Refer to C3 Model 410 Front and Rear
Views (page 25) for the location of the faceplate. On the C3 Model 410,
the faceplate can be removed and replaced. Refer to the following steps
for replacing the front faceplate.
Step
Action
Remove the seven (7) Phillips screws that secure the faceplate
to the C3 unit: two (2) screws on top, two (2) screws on bottom
and three (3) screws on the left side.
To reinstall the faceplate, align the faceplate screw holes with the
holes on the C3 unit and secure the screws removed in Step 2.
--End--
A black plastic faceplate frames the CD-ROM, tape drive and alarm board
on the front left side of the C3 unit. On the C3 Models 512 and 514, all
three of these units are housed in one assembly that can be pulled out for
maintenance purposes. Refer to Location of the Front Faceplate
Assembly (page 34) for the location of the faceplate assembly. Refer to
the following steps for replacing the front faceplate assembly.
20 December 2014
C3 Gateway Controller
Copyright 2000-2014 GENBAND. All Rights Reserved.
630-00610-01 12.01
Note: For the following procedure, the system must be shut down in
order to avoid system errors.
Step
Action
Remove the two (2) Phillips screws that secure the faceplate
assembly to the C3 unit, located on the inside right side of the
CD-ROM drive.
Firmly pull the faceplate assembly out one inch, so that the
power and data connectors are pulled out of their sockets in the
back of the faceplate assembly.
Disconnect the SCSI ribbon cable from the rear of the tape drive.
10
11
20 December 2014
12
Push the faceplate assembly forward so that the power and data
connectors are connected to their sockets in the back of the
faceplate assembly.
13
Attach the faceplate assembly to the C3 unit with the two (2)
Phillips screws, located on the inside right side of the CD-ROM
drive.
14
15
630-00610-01 12.01
--End--
The hard drives are located on the front right side of the C3 unit behind the
front single fan assembly. An C3 unit will have either two or four hard
drives, depending on the memory requirements of each C3 unit. Refer to
the following steps to replace a hard drive
20 December 2014
Step
Action
Remove the front single-fan assembly. Refer to the Front SingleFan Assembly (page 18).
Slide the thumb tab on the hard drive to the right and slide the
hard drive forward on the runners to remove the hard drive from
the C3 unit. Refer to C3 Hard Drive Assembly (page 35).
To install the new hard drive, slide the hard drive back on the
runners and into the C3 unit.
Replace the front single-fan assembly. Refer to the Front SingleFan Assembly (page 18).
630-00610-01 12.01
--End--
Action
Attention
Before issuing the eject command, ensure that the chassis door is
open.
20 December 2014
630-00610-01 12.01
Manually close the disk drive by pushing the drawer back into the
drive or by depressing the eject button.
--End--
Action
Slide the paper clip into the hole and press firmly. Do not hold the
straightened paper clip at an angle, as this may damage your
drive. Refer to Manually Ejecting a Disk (page 36). The disk
should now eject.
Manually close the disk drive by pushing the drawer back into the
drive or by depressing the eject button.
Manually Ejecting a Disk
--End--
20 December 2014
C3 Gateway Controller
Copyright 2000-2014 GENBAND. All Rights Reserved.
630-00610-01 12.01
Note: The following procedure is for the C3 Model 410 only. For Models
512 and 514, pleases see the next set of instructions.
Step
Action
Remove the four (4) pan-head screws located on the inside right
side of the CD-ROM drive.
Label and disconnect the SCSI and DC connectors from the rear
of the CD-ROM drive. Refer to Connectors on the CD/DVDROM Assembly (page 38).
Slide the drive assembly forward on the top runners and remove
it from the C3 unit.
To install a replacement drive, slide the new drive onto the top
runners of the 5.25 inch bay.
Note: Nine sets of jumper pins are on the rear of the CDROM assembly. Check to ensure the jumper pins are set
correctly. The SCSI target must be set to No. 6. The jumpers
should be inserted in the second, third and sixth positions on
the pin pairs.
20 December 2014
10
11
Screw down the CD-ROM drive assembly with the four (4)
Phillips screws.
12
13
14
630-00610-01 12.01
--End--
Note: The following procedure is for the C3 Models 512 and 514. For
the Model 410, please see the previous set of instructions.
Step
Action
Disconnect the SCSI and DC connectors from the rear of the CDROM drive. Refer to Connectors on the CD/DVD-ROM
Assembly (page 38).
Remove the four (4) Phillips screws from the CD-ROM drive.
Slide the drive assembly forward on the top runners and remove
it from the C3 unit.
To install a replacement drive, slide the new drive onto the top
runners of the bay.
Note: Nine sets of jumper pins are on the rear of the CDROM assembly. Check to ensure the jumper pins are set
correctly. The SCSI target must be set to No. 6. The jumpers
should be inserted in the second, third and sixth positions on
the pin pairs.
20 December 2014
Screw down the CD-ROM drive assembly with the four (4)
Phillips screws.
C3 Gateway Controller
Copyright 2000-2014 GENBAND. All Rights Reserved.
630-00610-01 12.01
The tape drive is located below the CD-ROM assembly in the left-front
position of the C3 chassis. On the C3 Model 410, the tape drive sits on
runners in the center slot, above the alarm board and below the CD-ROM
assembly. For the C3 Models 510, 512, and 514 the tape drive is part of a
larger assembly that also includes the CD/DVD drive and alarm board.
This assembly must be pulled out in order to replace the tape drive.
Note: The following procedure is for the C3 Model 410 only. For Models
512 and 514, pleases see the next set of instructions.
20 December 2014
Step
Action
Remove the four (4) pan-head screws located on the inside right
side of the tape drive assembly.
Disconnect and label the SCSI and DC connectors from the rear
of the assembly. Refer to Connectors on the Tape Drive
Assembly (page 40).
Slide the tape drive assembly forward on the center runners and
remove it from the C3 unit.
Remove the four jumpers from the pin pairs on the rear of the
tape drive assembly (reading left to right).
630-00610-01 12.01
Note: Store the jumpers for spare parts. One jumper is used
in the next step.
10
Set the SCSI target to No. 4. Place a jumper on the first pin pair
on the left. Jumpers should be located in the first, fifth and
seventh positions on the pin pairs.
11
Slide the new tape drive onto the center runners of the 5.25 inch
bay.
12
Note: Ensure that the black top of the DC power adapter plug
is facing up before inserting it into the connector.
13
Tighten the four (4) pan-head screws on the tape drive assembly.
15
Replace the front C3 unit fan assemblies by performing steps 4 6 of Front Dual-Fan Assembly (page 16) procedure.
16
20 December 2014
C3 Gateway Controller
Copyright 2000-2014 GENBAND. All Rights Reserved.
630-00610-01 12.01
--End--
Note: The following procedure is for the C3 Models 512 and 514. For
the Model 410, please see the previous set of instructions.
Step
Action
Remove the four (4) pan-head screws located on the inside right
side of the tape drive assembly.
Slide the tape drive assembly forward on the center runners and
remove it from the front faceplate assembly.
Remove the four jumpers from the pin pairs on the rear of the
tape drive assembly (reading left to right).
Note: Store the jumpers for spare parts. One jumper is used
in the next step.
7
20 December 2014
Set the SCSI target to No. 4. Place a jumper on the first pin pair
on the left. Jumpers should be located in the first, fifth and
seventh positions on the pin pairs.
Maintenance and Repair Guide
Copyright 2000-2014 GENBAND. All Rights Reserved.
630-00610-01 12.01
Slide the new tape drive onto the center runners of the front
faceplate assembly.
Note: Ensure that the black top of the DC power adapter plug
is facing up before inserting it into the connector.
10
Tighten the four (4) pan-head screws on the tape drive assembly.
11
The SS7 card is located at the rear right side of the C3 unit. Refer to the
following steps to replace the SS7 card.
20 December 2014
Step
Action
Remove the screw from the top of the faceplate that is securing
the SS7 card. Refer to C3 Model 410 Front and Rear Views
(page 25) for card location.
To install a replacement SS7 card, insert the card into the empty
SS7 card slot.
Secure the SS7 card to the faceplate with the screw that was
removed in Step 5.
10
C3 Gateway Controller
Copyright 2000-2014 GENBAND. All Rights Reserved.
630-00610-01 12.01
SS7 and Ethernet Card Port Numbering (Model 410 and 514)
--End--
In the Model 410 C3, there is an Ethernet card located at the rear right side
of the unit. Refer to the following steps to replace the Ethernet card. In
other models, the Ethernet connections are not on a replaceable card.
20 December 2014
Step
Action
Remove the screw from the top of the faceplate that is securing
the Ethernet card. Refer to C3 Model 410 Front and Rear Views
(page 25) for card location.
630-00610-01 12.01
Secure the Ethernet card to the faceplate with the screw that was
removed in Step 5.
10
20 December 2014
Step
Action
Pull the white extraction levers open that are holding the topmost
card in place (slot number 8).
Insert the first card into the header until the white tabs
automatically close.
C3 Gateway Controller
Copyright 2000-2014 GENBAND. All Rights Reserved.
630-00610-01 12.01
--End--
The C3 alarm interface card is located at the top front of the C3 unit behind
the C3 alarm panel. Use the following steps to remove the C3 alarm
interface card.
20 December 2014
630-00610-01 12.01
Attention
Use caution when removing screws from the C3 alarm interface panel and card.
Dropping a screw within the C3 unit may damage the C3 components.
Action
Action
Secure the C3 alarm interface card into place with the four
Phillips-head screws.
Install the C3 alarm interface front panel with the four Phillipshead screws.
--End--
20 December 2014
C3 Gateway Controller
Copyright 2000-2014 GENBAND. All Rights Reserved.
630-00610-01 12.01
The C3 alarm board is located below the tape drive at the front left of the
C3 unit. On the C3 Models 512 and 514, the alarm board is part of a larger
assembly that includes the tape drive and CD/DVD drive. This assembly
must be pulled out in order to replace the alarm board. Refer to the
following steps to remove and replace the C3 alarm board.
Location of Alarm Board
Action
Remove the four (4) Phillips screws located on the inside right
side of the alarm board.
Slide the alarm board forward on the bottom runners and remove
it from the front faceplate assembly.
Slide the new alarm board onto the bottom runners of the front
faceplate assembly.
Tighten the four (4) Phillips screws on the alarm board assembly.
20 December 2014
630-00610-01 12.01
20 December 2014
C3 Gateway Controller
Copyright 2000-2014 GENBAND. All Rights Reserved.
630-00610-01 12.01
49
Attention
Action
20 December 2014
630-00610-01 12.01
2. View the power feed LEDs on the back of the target C3 node.
Verify that the top and bottom LEDs of each triplet LED set
are lit green. See T2000 rear view showing power feed
LEDs (page 50) and T5220 rear view showing power feed
LEDs (page 50):
T2000 rear view showing power feed LEDs
Attention
If the PDU breaker is flipped and the power feed LEDs remain lit,
the wrong breaker has been selected. Flip the breaker back to
the ON position, and contact GENBAND Customer Support for
assistance before proceeding.
20 December 2014
C3 Gateway Controller
Copyright 2000-2014 GENBAND. All Rights Reserved.
630-00610-01 12.01
Attention
If the PDU breakers are flipped and any of the power feed LEDs
remain lit, the wrong breakers have been selected. Flip the
breakers back to the ON position, and contact GENBAND
Customer Support for assistance before proceeding.
Attention
2. Flip the front faceplate of the T2000 or T5220 out and down
to reveal the disk drives. See T2000 front faceplate opening
(page 51) for a view of the T2000. See T5220 front faceplate
closed (page 51) and T5220 front faceplate open (page 52)
for images depicting the T5220.
T2000 front faceplate opening
20 December 2014
630-00610-01 12.01
3. Locate the two disk drives, HDD0 (boot disk) and HDD1 (data
disk), as shown in T2000 disk drive locations behind the
front faceplate (page 52):
T2000 disk drive locations behind the front faceplate
20 December 2014
C3 Gateway Controller
Copyright 2000-2014 GENBAND. All Rights Reserved.
630-00610-01 12.01
Attention
The latch is not an ejector. Do not bend the latch to the left. Doing
so may damage the latch.
5. Grasp the latch and pull out until the drive is removed from
the slot. See the example in T2000 disk drive removal
(page 53):
T2000 disk drive removal
6. Remove the new disk drive from its anti-static packaging and
prepare to slide it into the bay just vacated.
Attention
7. Slide the new drive into the bay until the drive is fully seated.
See the example of T2000 disk drive insertion (page 54):
20 December 2014
630-00610-01 12.01
8. Close the latch to lock the drive in place. Then close the
faceplate to cover the drives. See T2000 front faceplate
closing (page 54):
T2000 front faceplate closing
Attention
If the power feed LEDs do not have the required pattern (green
on top, off in the middle, green on bottom), resolve the problem
before continuing. Contact GENBAND Customer Support for
assistance if needed.
20 December 2014
C3 Gateway Controller
Copyright 2000-2014 GENBAND. All Rights Reserved.
630-00610-01 12.01
--End--
20 December 2014
630-00610-01 12.01
Step
Action
Step 1
Step 3
--End--
20 December 2014
C3 Gateway Controller
Copyright 2000-2014 GENBAND. All Rights Reserved.
630-00610-01 12.01
57
In this section:
Required Tools
Flat-blade screwdriver
No. 1 Phillips-head (cross-point) screwdriver
No. 2 Phillips-head (cross-point) screwdriver
Personal grounding device, such as an anti-static wrist strap and a
grounded conductive pad
Note: All references to left, right, front, top, and bottom in the
following procedures assume that you are facing the front of the
server, as it would be positioned for normal operation.
Attention
Electrostatic discharge (ESD) and ESD protection: ESD can damage disk
drives, boards, and other parts. We recommend that you perform all
procedures in this chapter only at an ESD workstation. If one is not
available, provide some ESD protection by wearing an antistatic wrist strap
attached to chassis ground (any unpainted metal surface) on your server
when handling parts.
20 December 2014
630-00610-01 12.01
Remove the front bezel of the C3 IA RMS-based platform for tasks such
as:
Action
Loosen the captive bezel retention screw on the right side of the
bezel ( Removing the Front Bezel (page 58), A).
Rotate the bezel to the left to free it from the pins on the front
panel, ( Removing the Front Bezel (page 58), B) and remove
it.
--End--
Removing the Front Bezel (page 58) shows how to remove the front
bezel.
Removing the Front Bezel
20 December 2014
C3 Gateway Controller
Copyright 2000-2014 GENBAND. All Rights Reserved.
630-00610-01 12.01
Action
Insert the tabs on the left side of the bezel into the slots on the
front panel of the chassis.
Move the bezel toward the right and align it on the front panel
pins.
Snap the bezel into place and tighten the retention screw to
secure it.
--End--
The power supply module is rated for 650W output capability in full AC or
DC input voltage range. The minimum steady-state DC input voltage at
which the equipment remains fully operational is -38 VDC. The nominal
operating voltage of the DC system is -48 VDC.
AC and DC Power Supplies (page 60) shows details about the AC and
DC power supply modules.
20 December 2014
630-00610-01 12.01
Action
Press the green safety lock towards the right side ( Replacing an
AC Power Supply Module (page 61), A) and using the handle,
remove the power supply module.Press and hold the green
safety lock downward ( Replacing an AC Power Supply Module
(page 61), B) and using the handle, slide the power supply into
the slot until it latches into place ( Replacing an AC Power
Supply Module (page 61), C).
C3 Gateway Controller
Copyright 2000-2014 GENBAND. All Rights Reserved.
630-00610-01 12.01
The air filter is located behind the front bezel of the C3 Controller. The C3
Controller is equipped with thermal sensors to monitor the internal
temperature of the system. If the air filter gets clogged so that the fans are
not able to pull air through the system, the internal temperature will rise
causing a Minor and/or Major telco alarms manager (TAM) LED to be
asserted. This active alarm provides an indication that the air filter should
be inspected and/or replaced.
Action
Lay the new filter on the back of the front bezel as shown in the
following figure.
Replacing the Filter
20 December 2014
630-00610-01 12.01
The IA-RMS chassis supports two hot-swappable hard disk drives, which
are accessible from the front of the chassis with the bezel removed. The
hard disk drives are mounted in removable drive carriers that latch into the
drive bay sub-assembly.
The boot and data drives are mirrored in a RAID configuration on the IARMS platform. Hence, it is likely that at most times a single disk will fail,
which will not require powering down the C3 controller.
Attention
20 December 2014
Step
Action
Select the drive slot where you want to replace the drive.
C3 Gateway Controller
Copyright 2000-2014 GENBAND. All Rights Reserved.
630-00610-01 12.01
20 December 2014
Step
Action
Remove the hard drive by unfastening the four screws that attach
the drive to the drive carrier ( Removing a Hard Drive (page 64)
A). Set the screws aside for use with the new drive.
630-00610-01 12.01
20 December 2014
Install the new drive in the drive carrier ( Installing a Hard Drive
(page 65) A) and secure the drive with the four screws that
come with the carrier ( Installing a Hard Drive (page 65) B).
C3 Gateway Controller
Copyright 2000-2014 GENBAND. All Rights Reserved.
630-00610-01 12.01
With the drive carrier locking lever fully open, push the hard drive
carrier into the drive slot in the chassis until it stops ( Inserting a
New Hard Drive into the Chassis (page 66) A).
Press the locking lever until it snaps shut and secures the drive
in the slot ( Inserting a New Hard Drive into the Chassis
(page 66) B).
Inserting a New Hard Drive into the Chassis (page 66) shows how to
insert a new hard drive into the chassis.
20 December 2014
630-00610-01 12.01
20 December 2014
C3 Gateway Controller
Copyright 2000-2014 GENBAND. All Rights Reserved.
630-00610-01 12.01
C3 Gateway Controller
Release:14.0
Publication:630-00610-01
Document Revision:12.01
Document release date:20 December 2014
Copyright 2000-2014 GENBAND. All rights reserved. Use of this documentation and its contents is subject to the terms and
conditions of the applicable end user or software license agreement, right to use notice, and all relevant copyright protections.
GENBAND, the GENBAND corporate logo and tagline, and certain of GENBAND's product and solution names are registered
trademarks of GENBAND and its affiliates.
While the information in this document is believed to be accurate and reliable, except as otherwise expressly agreed to in writing,
GENBAND AND/OR ITS LICENSORS PROVIDES THIS DOCUMENT "AS IS" WITHOUT WARRANTY OR CONDITION OF ANY
KIND, EITHER EXPRESS OR IMPLIED. The information and/or products described in this document are subject to change
without notice.
THE INFORMATION CONTAINED HEREIN IS THE PROPERTY OF GENBAND OR ITS LICENSORS AND MUST NOT BE
DISCLOSED, OTHER THAN TO EMPLOYEES OF GENBAND OR CUSTOMERS WITH NEED-TO-KNOW, WITHOUT THE
PRIOR WRITTEN CONSENT OF GENBAND OR ITS LICENSORS. THE INFORMATION MUST NOT BE DISCLOSED TO
SUBCONTRACTORS OR REGULATORY AUTHORITIES. GENBAND MUST BE NOTIFIED OF ANY REQUEST OR ORDER
FOR DISCLOSURE PRIOR TO SUCH DISCLOSURE.
For access to the Document Center, log in through the Customer Support website at http://cust.genband.com.
www.genband.com