Beruflich Dokumente
Kultur Dokumente
Page 1 of 8
sds no. : 195727
V002.1
TURCO 4181
Revision: 07.12.2010
printing date: 18.07.2012
ua-productsafety.uk@uk.henkel.com
2. Hazards identification
Classification of the substance or mixture:
Classification (CLP):
No data available.
Classification (DPD):
C - Corrosive
R35 Causes severe burns.
Label elements (CLP):
No data available.
MSDS-No.: 195727
V002.1
TURCO 4181
Page 2 of 8
Risk phrases:
R35 Causes severe burns.
Safety phrases:
S22 Do not breathe dust.
S26 In case of contact with eyes, rinse immediately with plenty of water and seek medical advice.
S36/37/39 Wear suitable protective clothing, gloves and eye/face protection.
S45 In case of accident or if you feel unwell, seek medical advice immediately (show the label where possible).
Contains:
Sodium hydroxide
Other hazards:
None if used properly.
3. Composition/information on ingredients
Declaration of the ingredients according to CLP (EC) No 1272/2008:
Hazardous components
CAS-No.
Sodium hydroxide
1310-73-2
EC Number
REACH-Reg No.
215-185-5
content
Classification
> 25 %
Skin corrosion 1A
H314
Only dangerous ingredients for which a CLP classification is already available are displayed in this table.
For full text of the H - statements and other abbreviations see section 16 "Other information".
Substances without classification may have community workplace exposure limits available.
Declaration of ingredients according to DPD (EC) No 1999/45:
Hazardous components
CAS-No.
Sodium hydroxide
1310-73-2
EC Number
REACH-Reg No.
215-185-5
content
Classification
> 25 %
C - Corrosive; R35
For full text of the R-Phrases indicated by codes see section 16 'Other Information'.
Substances without classification may have community workplace exposure limits available.
Declaration of ingredients according to Detergent Regulation 648/2004/EC
<5%
non-ionic surfactants
MSDS-No.: 195727
V002.1
TURCO 4181
Page 3 of 8
Skin contact:
Rinse with running water and soap. Apply replenishing cream. Change all contaminated clothing.
Seek medical attention from a specialist.
Eye contact:
Immediately flush eyes with soft jet of water or eye rinse solution for at least 15 minutes. Hold eyelid wide-open. Seek a
doctor/hospital, eye flushing should continue during transportation to a doctor.
Ingestion:
Rinse out mouth, drink 1-2 glasses of water, do not induce vomiting.
Immediate medical treatment necessary.
Most important symptoms and effects, both acute and delayed:
Causes burns.
5. Firefighting measures
Extinguishing media:
Suitable extinguishing media:
All common extinguishing agents are suitable.
Special hazards arising from the substance or mixture:
Formation of toxic gases is possible during heating or in fires.
Advice for firefighters:
Wear protective equipment.
Wear self-contained breathing apparatus.
MSDS-No.: 195727
V002.1
TURCO 4181
Page 4 of 8
ppm
mg/m3
2
Type
Short Term Exposure
Limit (STEL):
Category
Remarks
EH40 WEL
Exposure controls:
Engineering controls:
Thorough dedusting.
Respiratory protection:
dust mask when dust is generated
Dust mask, P2 or P3 particle filter.
Hand protection:
Chemical-resistant protective gloves (EN 374). Suitable materials for short-term contact or splashes (recommended: at least
protection index 2, corresponding to > 30 minutes permeation time as per EN 374): Polychloroprene (CR; >= 1 mm
thickness) or natural rubber (NR; >=1 mm thickness) Suitable materials for longer, direct contact (recommended: protection
index 6, corresponding to > 480 minutes permeation time as per EN 374): Polychloroprene (CR; >= 1 mm thickness) or
natural rubber (NR; >=1 mm thickness) This information is based on literature references and on information provided by
glove manufacturers, or is derived by analogy with similar substances. Please note that in practice the working life of
chemical-resistant protective gloves may be considerably shorter than the permeation time determined in accordance with EN
374 as a result of the many influencing factors (e.g. temperature). If signs of wear and tear are noticed then the gloves should
be replaced.
Eye protection:
Goggles which can be tightly sealed.
Skin protection:
Protective clothing that covers arms and legs.
pH
12,50 - 13,60
No data available.
not applicable
No data available.
No data available.
No data available.
No data available.
MSDS-No.: 195727
V002.1
TURCO 4181
Page 5 of 8
Viscosity
Viscosity (kinematic)
Explosive properties
Solubility (qualitative)
Solidification temperature
Melting point
Flammability
Auto-ignition temperature
Explosive limits
Partition coefficient: n-octanol/water
Evaporation rate
Vapor density
Oxidising properties
No data available.
No data available.
No data available.
No data available.
No data available.
No data available.
No data available.
No data available.
No data available.
No data available.
No data available.
No data available.
No data available.
Other information:
No data available.
Acute toxicity:
Hazardous components
CAS-No.
Sodium hydroxide
1310-73-2
Value
type
LDLo
Value
500 mg/kg
Route of
application
oral
Exposure
time
Species
rabbit
Method
MSDS-No.: 195727
V002.1
TURCO 4181
Page 6 of 8
Result
negative
Type of study /
Route of
administration
bacterial forward
mutation assay
Metabolic
activation /
Exposure time
no data
Species
Method
Toxicity:
Hazardous components
CAS-No.
Value
type
Value
Sodium hydroxide
1310-73-2
LC50
189 mg/l
Acute
Toxicity
Study
Fish
Sodium hydroxide
1310-73-2
EC50
Daphnia
Exposure
time
Species
Method
48 h
OECD Guideline
203 (Fish, Acute
Toxicity Test)
OECD Guideline
202 (Daphnia sp.
Acute
Immobilisation
Test)
Daphnia sp.
MSDS-No.: 195727
V002.1
TURCO 4181
Page 7 of 8
8
II
C6
80
1823
8
SODIUM HYDROXIDE, SOLID (mixture)
(E)
8
II
C6
80
1823
8
SODIUM HYDROXIDE, SOLID (mixture)
8
II
C6
1823
8
SODIUM HYDROXIDE, SOLID (mixture)
8
II
1823
8
F-A ,S-B
SODIUM HYDROXIDE, SOLID (mixture)
8
II
814
816
1823
8
Sodium hydroxide, solid (mixture)
MSDS-No.: 195727
V002.1
Remarks
TURCO 4181
Page 8 of 8
Further information:
This information is based on our current level of knowledge and relates to the product in the state in which it is delivered. It is
intended to describe our products from the point of view of safety requirements and is not intended to guarantee any
particular properties.