Beruflich Dokumente
Kultur Dokumente
D DRIVELINE/AXLE
A
SECTION
REAR AXLE
RAX
CONTENTS
PRECAUTIONS .......................................................... 2
Precautions .............................................................. 2
PREPARATION ........................................................... 3
Special Service Tool ................................................. 3
Commercial Service Tool ......................................... 4
NOISE, VIBRATION, AND HARSHNESS (NVH)
TROUBLESHOOTING ................................................ 5
NVH Troubleshooting Chart ..................................... 5
WHEEL HUB (2WD) ................................................... 6
On-Vehicle Inspection .............................................. 6
REAR WHEEL BEARING ..................................... 6
RAX-1
PRECAUTIONS
PRECAUTIONS
Precautions
PFP:00001
EDS000F1
RAX-2
PREPARATION
PREPARATION
Special Service Tool
PFP:00002
A
EDS000F2
Tool name
Tool number
Description
Drift
ST30613000
a: 72 mm dia.
b: 48 mm dia.
RAX
ZZA1000D
E
Removing and installing wheel
bearing lock nut
F
ZZA1228D
G
Axle stand
KV40101000
ZZA1093D
Sliding hammer
ST36230000
ZZA0803D
Drift
ST1523S000
ST15231000
a: 44 mm dia.
b: 80 mm dia.
ST15243000
ZZA1106D
RAX-3
ZZA0881D
PREPARATION
Tool name
Tool number
Description
Drift bar
ST35325000
ZZA1140D
Drift
KV401053S0
KV40105310
a: 89.1 mm (3.508 in) dia.
b: 80.7 mm (3.177 in) dia.
KV40105320
KV40105330
ZZA0808D
EDS000H2
Tool name
Description
S-NT360
RAX-4
PFP:00003
A
EDS000FO
Symptom
REAR
AXLE
Noise
Shake
Vibration
Shimmy
Judder
: Applicable
RAX-5
C
NVH in PS section.
NVH in BR section.
ROAD WEEL
NVH in WT section.
TIRES
NVH in WT section.
REAR AXLE
RAX
STEERING
DRIVE SHAFT
BRAKES
NVH in PR section.
Shake
DIFFERENTIAL
PROPELLER SHAFT
Parts interference
Noise
DRIVE
SHAFT
Imbalance
Refer to RAX-6
Reference page
Use the chart below to help you find the cause of the symptom. If necessary, repair or replace these parts.
PFP:43200
EDS000F3
Check rear axle for excessive play, crack, wear, and other damage.
SMA525A
Move wheel hub in axial direction by hand, and check rear wheel bearing for looseness.
Axial end play
Part No.
43086
43087
43088
43089
43090
43086
43086
P0110
P1011
P0100
P0110
P0110
B9500
01G00
Check for unusual noise by rotating wheel. If noise is heard, replace wheel bearing.
If any malfunction is detected, replace wheel hub.
RAX-6
EDS000F4
RAX
J
SDIA0480E
Axle housing
Adjusting shim
Oil seal
Lock washer
Bearing cage
Baffle plate
10 Grease seal
11 Bearing spacer
12 Axle shaft
REMOVAL
1.
2.
3.
4.
5.
Remove tires, and remove parking cables from back plate and operating lever.
Remove brake tube from wheel cylinder.
CAUTION:
While brake tube is removed, be sure to protect painted surface from brake fluid.
While brake tube is removed, do not depress brake pedal.
Remove axle mounting nuts, and remove axle shaft assembly
from axle housing.
If axle shaft assembly is difficult to remove by seizure, use a
sliding hammer (special service tool) and axle stand (special
service tool).
Remove O-ring from axle housing.
Using a flat-bladed screwdriver, remove oil seal.
CAUTION:
During removal, be careful not to scratch axle housing.
RAB0263D
RAX-7
Check shaft for cracks, bend, and uneven wear. If any, replace shaft.
Wheel Bearing
Check bearing for deformation, cracks, damage, or uneven wear. If any, replace wheel bearing assembly.
INSTALLATION
1.
2.
3.
4.
5.
Using a drift (special service tool) and drift bar (special service
tool), install oil seal to axle housing as shown in the figure.
CAUTION:
Do not reuse oil seal. Before installing, apply grease (Nissan MP Special Grease No. 2) to lip.
Install O-ring to axle housing.
CAUTION:
Do not reuse O-ring.
Set axle shaft assembly to axle housing, and tighten axle mounting nuts to specified torque.
CAUTION:
Do not reuse mounting nuts.
Install parking cable and brake tube.
Bleed air in brake system.
RAB0302D
EDS000F5
DISASSEMBLY
1.
2.
3.
4.
5.
SDIA0390J
6.
7.
8.
9.
RAB0244D
10. Using a drift (suitable tool), remove wheel bearing from bearing cage.
RAX-8
C
SDIA0553E
RAX
Check shaft for cracks, bend, uneven wear, or dent. If any, replace shaft.
Wheel Bearing
Check bearing for deformation, cracks, or uneven wear. If any, replace wheel bearing assembly.
F
ASSEMBLY
1.
Using a drift (suitable tool), press wheel bearing into rear axle
bearing cage with a press.
CAUTION:
Apply grease to wheel bearing.
During press-in, do not press wheel bearing inner race.
Do not reuse wheel bearing.
SDIA0554E
Using a drift (suitable tool), press grease seal into axle bearing
cage with a press.
CAUTION:
Do not reuse grease seal. Apply grease to lip.
4.
SDIA0555E
RAX-9
6.
8.
9.
: 0.599 - 2.834 Nm
(0.07 - 0.28 kgm,6-25 inlb)
: 8.9 - 42 N (0.9 - 4.3 kg,2.0-9.5
lb)
RAX-10
SDIA0557E
PFP:00030
A
EDS000F6
Without ABS
Rotation torque
RAX
RAX-11
RAX-12