Beruflich Dokumente
Kultur Dokumente
A marker is a diagram of a precise arrangement of pattern pieces for a specific style and the sizes to be cut
from a single spread. On another word, Marker making is the process of determining the most efficient layout
of pattern pieces for a specified style, fabric and distribution of sizes.
A marker is a mixing of many pattern sizes drawn on to a thin paper prior to cutting. Having a marker
made it means that the design you will have the best utilization of fabrics saving money.
Marker Efficiency:
Marker efficiency is determined by the fabric utilization, the percentage of the total fabric that is actually
used in garment parts. The area not used in garment parts is waste. Marker efficiency depends on how tightly
the pattern pieces fit together within the marker.
Marker planner: The efficiency of marker mainly depends on the competency, experience,
honesty and technical knowledge of the marker planner.
Size of the garments: Smaller and larger sizes lead to less marker efficiency, medium garment
sizes gives higher marker efficiency.
Numbers of sizes in a style: fewer and higher numbers of sizes in a style leads to less marker
efficiency and higher marker efficiency may achieved from medium numbers of sizes in a style.
Marker length: For higher marker length, higher marker efficiency and production of cutting
room can be increased.
Pattern Engineering: Marker efficiency can be increased by changing pattern design of
particular parts of the garments.
Fabric characteristics: Usually symmetrical fabric provides higher marker efficiency and
asymmetric fabric leads lower marker efficiency.
Marker making method: In computerized method efficiency is more than manual method.
Marker width: The more marker width, the easier to marker plan and ensures higher marker
efficiency.
Style of the garments: The more large patterns and less small patterns reduce marker
efficiency.
Methods:
Methods of marker making are as follows:
Manual method.
Computerized method.
Manual method:
In this process, marker can be made in two ways,
a. By using full size pattern: markers may be created by arranging full size pattern pieces on marker
paper or directly on the top ply of the fabric in a spread. And then full size pattern pieces on marker
paper. Full size pieces must be manipulated, adjusted and readjusted on normal fabric widths.
b. By using miniaturized pattern: In this method, full size pattern pieces are reduced to 1/5 of its
original size by using pantograph. These miniaturized pattern pieces are usually made by plastic sheet
or thick board paper. Marker planning is done by using those miniaturized patterns. The marker is
reproduced full size using the mini-marker as a reference.
The area of the covered pattern can be determined by using planimeter to get the marker efficiency. In
this way, it is possible to get higher marker efficiency as control over the marker is better than the full
size pattern. This method is rapidly being replaced by computerized method.
Manual methods of marker making are time consuming and require a great deal of space.
Manually made markers are also subject to errors and inconsistencies that may occur in grain variation,
poor line definition, placement and alignment of pieces and slip of the pieces.
Accuracy of a manually made marker depends on the skill of the individual who laid out the marker and
traced it.
Computerized method:
Computerized marker making is very accurate and provides the greatest opportunity for pattern
manipulation, marker efficiency and shortest response time.
Production patterns may be developed on the computer or digitized or scanned in to the computer.
In addition, parameters for markers are entered in to the computer from cutting orders.
These might include style numbers, size distribution and fabric width. Technicians manipulate pattern
images on the computer screens and experiment on various configurations to deter mined the best material
utilization for the marker.
Protective devices are built in to the programs to ensure the grain alignment and prevent overlapping of
pieces.
Once markers have been planned and stored, they can be printed or recalled and modified for new cutting
orders.
With newer marker making software, markers can be automatically created.
A computer can automatically develop up to seven different markers according to the criteria set by a
technician.
Automatic marker making may be used to determine yardage requirements and fabric costs for designs
prior to line adoption.
With automatic marker making, a 50-pieces marker can be generated on the computer screen in less than a
minute.
Advantages of computerized method:
Benefits are said to include
Increases in material efficiency with subsequent decreases in material waste,
Time and labour savings in making markers;
Improvements in overall marker quality;
Tighter markers;
Avoidance of backlogs during peak periods; and
Fast, precise cost proposals for clients.
Differences:
a. Grain Line: Grain line is indicated in every piece of the pattern. Patterns are supposed to be parallel to the
wrap in woven fabric and wale in the knitted fabric. Hang and drape of the garment is depending on the
matching of grain line. To maintain grain line is one of the biggest constraints to achieve higher marker
efficiency.
b. Characteristics of the fabric: Special attention required to set pattern pieces on the asymmetrical fabric,
such as pile fabric, special print etc.
c. Design of the garments: Garments from check or stripe fabric requires mirror image (matching check or
stripe in adjacent two parts of the garment). Special attention is required to achieve the mirror image in the
garments.
d. Cutting Quality: Patterns are cut by knife blade from the lay. Natural width of cutting blade is a barrier to
move 90 angel in the cutting lay. Marker should be made carefully so that cutting blade can move easily in
the lay; otherwise there would be a possibility to get defective pattern pieces after cutting.
Selvedge losses:
Each fabric has two selvedges along wide. The amount of cut out is considered 3%
(approximately) along wide. The amount of fabric wide to be depends on the quality of
the selvedge, width and alignment of the selvedge. The more fabric width, the less will
be fabric wastage.
Purchase loss:
Fabric length is marked/ identified by fabric manufacturers and supplier on fabric roll.
Sometimes less fabric is wound on roll than identified length. So it should be measure
before fabric purchase.
.
b. Paint Spray: In spray marking, fine jets of paint are sprayed over the patterns that have been laid
on the fabric, leaving an outline of the patterns when they are removed. This method is faster than chalking,
however,
2. Marking on the paper: In this method, pattern pieces are precisely arranged on to the marker paper and
draw the outline of the patterns by using pencil. This method is widely used in the industry.
3. Computerized Drawing: Computerized methods are used for large volume production and they function as
follows:
Graded patterns in the computer are manipulated on screen to produce a marker.
the corresponding fabric width is shown on the screen and the range of the pattern pieces are shown on top.
These pieces can be rotated, reversed and moved into place
The computer can calculate marker efficiency.
The completed marker is then drawn using a linked digital plotter.
These systems are extremely quick and accurate and an unlimited quantity of markers can be produced
and/or reproduced.
4. Photographic System: With the photographic method, the patterns pieces are set onto a light sensitive
paper passing through ultra-violet light and revealed by using ammonia vapor. This method is quick and clean.
In manual duplicating, the patterns are drawn around by hand on to the paper. The other methods are
a. Carbon duplicating
b. Spirit duplicating
c. Photographic method
d. Perforated method.
a. Carbon duplicating: Carbon duplicating uses interleaved and carbon paper to replicate outlines drawn on
the top sheet. This duplication method has fairly low capital and material costs, however its disadvantages are
as follows:
It is dirty
It leaves poor impressions on the lower layers of the paper.
Care must be taken to avoid carbon slippage.
b. Spirit duplicating: Spirit duplicating machine and its working procedure is same as Office duplicating
machine/Xerox machine, Only significant difference is that the size of the machine. This method is suitable
when 40-50 duplication per master is required.
c. Photographic method: With the photographic method, the original marker is set onto a light sensitive paper
using ultra-violet light and revealed by using ammonia vapor. This method is quick and clean and produces
unlimited numbers of duplications.
d. Perforated method: The perforated method is an obsolete technique that involves punching a series of
perforation around the marker, placing it on the fabric and lightly dusting with chalk. It can be used many
times.
It is a dirty process and poor line definition can result unless great attention is given.