Sie sind auf Seite 1von 4

Part A

1. What do you mean by transistor biasing? Give its importance.


2. Explain need for stabilization of any BJT. List types of stability factors.
3. What is the significance of stability factor? Define S, S and S.
4. Define stability factor and obtain expression for fixed bias.
5. Explain how operating point is selected for amplification in CE mode.
6. Explain the working of emitter bias circuit. Write its advantages over fixed bias.
7. What is the effect of bypass capacitor on biasing?
8. What is the effect of cascading on gain and bandwidth of an RC coupled amplifier?
9. What are the drawbacks of fixed bias circuit?
10. What do you mean by feedback? What are the various feedback topologies?
11. Differentiate between degenerative and regenerative feedback.
12. What is desensitivity? What is its significance?
13. Define the terms loop gain , sensitivity and feedback in decibel associated with feedback
amplifiers.
14. What are the advantages of negative feedback?
15. Briefly explain Barkhausen criterion for feedback oscillators.
16. Draw the circuit of RC phase shift oscillators.
17. Draw the circuit of of wienbridge oscillator.
18. Draw the circuit of colpitts oscillator.
19. Draw the circuit of hartly oscillator.

Part B

20. Draw the circuit of Fixed bias and find its stability factor. Explain its advantages and
disadvantages.
21. Draw the circuit of collector to base bias and find its stability factor. Explain its
advantages and disadvantages.
22. Draw the circuit of Voltage divider bias and find its stability factor. Explain its
advantages and disadvantages.
23. With neat circuit diagram explain an RC coupled amplifier, functions of different
components and its frequency response.
24. Briefly explain the advantages of negative feedback.
25. What are the various types of feedback in amplifiers? Compare them.
26. Explain the working of RC phase shift oscillators.
27. Explain the working of wienbridge oscillator.
28. Explain the working of colpitts oscillator.
29. Explain the working of hartly oscillator.
30. For the voltage divider circuit R1 = 36K, R2 =9K, Rc = 9K, RE = 2K, Vcc=24V,
VBE = 0.7V. Calculate IC, VCE, and S for =100.
31. For the collector to base bias circuit Rc = 9K, RB = 2K, Vcc=10V, VBE = 0.7V. Calculate
IC, CE, and S for =100.
32. Design a voltage divider circuit for IC =2mA and VCE = 25% of VCC.(take = 100). If an
RC coupled amplifier circuit is biased in the above manner, discuss the performance of
the circuit.
33. An amplifier with a closed loop gain of 2002% is required. The amplifier available has a
gain variation of 20%. Determine required value of open loop gain and feedback factor.
34. An amplifier with an open loop gain of 100 with a lower cut off frequency of 100Hz and
upper cut-off frequency of 100 KHz is available. If 10% of output voltage is feedback to
input in negative feedback mode, find their resultant values.
35. Explain the principal and classification of oscillators? What are the practical
considerations?

Part A

1. What is the working principal of a RC integrator circuit?


2. What is the working principal of a RC differentiating circuit?
3. What are the condition for an integrator circuit?
4. What are the condition for a differentiator circuit?
5. Obtain the output waveform of the following circuit.

6. Obtain the output waveform of the following circuit.


7. Obtain the output waveform of the following circuit.
8. Explain a positive clamper circuit.
9. Explain a negative clamper circuit.
10. Design a differentiator circuit to differentiate a square wave of 10Vpp amplitude and
1 KHz frequency.
11. Design a integrator circuit to integrate a square wave of 10Vpp amplitude and 1 KHz
frequency.
12. What is percentage tilt. Derive the expression for percentage tilt for a single RC circuit..
13. Derive the expression for rise time for a single RC circuit.
14. Draw the block schematic of regulated power supply.
15. Define TUF and what is its significance?
16. What is ripple factor?
17. What is PIV?
18. Compare the performance of a capacitor, inductor and LC filter.
19. Explain a simple zener diode shunt regulator circuit.
20. Compare the performance of shunt and series regulators.
21. Explain the working of a current limiting circuit.
22. Draw the internal diagram of 555 IC.
23. Write notes on 78XX.
24. Write notes on 79XX.
25. How LM317 works as a regulator.
26. Write notes on SMPS.

Part B

27. Draw the circuit of integrator and derive the expression for its output. Under what
condition this circuit behave as an integrator. Plot the response for a square wave input
and obtain necessary design equations.
28. Draw the circuit of integrator and derive the expression for its output. Under what
condition this circuit behave as an integrator. Plot the response for a square wave input
and obtain necessary design equations.
29. With the help of transfer characteristics, explain the working of double clipper and slicer.
30. Design a circuit to obtain the following transfer characteristics.

31. Design a circuit to obtain the following transfer characteristics.


32. Obtain the output waveform of the following circuit.

33. Obtain the output waveform of the following circuit.

34. Draw the circuit of a half wave rectifier and explain the working. Obtain the performance
measure of a regulator.
35. Draw the circuit of a center tapped wave rectifier and explain the working. Obtain the
performance measure of a regulator.
36. Draw the circuit of a bridged full wave rectifier and explain the working. Obtain the
performance measure of a regulator.
37. Explain the working of a capacitor filter.
38. Explain the working of 555 IC with neat diagram.
39. Design an astable multivibrator using 555IC got duty cycle of 50%.
40. Design an Monostablr multivibrator using 555IC got duty cycle of 50%.

Das könnte Ihnen auch gefallen