Beruflich Dokumente
Kultur Dokumente
Piston Pumps
PVH high flow, high performance pumps These are efficient , reliable pumps, with
are a family of variable displacement, a selection of optional controls for
inline piston units that incorporate the maximum operational flexibility.
proven design, quality manufacturing Designed specifically for strenuous
techniques and operating features of application, they provide the productivity
other Vickers piston pumps, but in a gains and controllability improvements
smaller, lighter package. desired in earthmoving, construction,
machine tool, plastics, and all other
The PVH series has been specially energy-conscious markets. As with all
designed to meet the 250 bar (3625 psi) Vickers products, these pumps have
continuous duty performance been fully laboratory tested and field
requirements of new generation proven.
equipment designs.
2
Table of Contents
Model Codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Performance Data
Rated characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Performance curves . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Response data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Sound levels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Control Options
Pressure compensator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Load sensing and pressure compensator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Remotely controllable pressure compensator with load sensing option . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Pressure and torque limiter control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Pressure and torque limiting plus load sensing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Input Shaft Selection Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Input Shaft Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Installation Dimensions
Basic pumps (non-thru-drive) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Adjustable maximum volume stop . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Thru-drive pumps . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
ISO pump mounting flange . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Combination 2-bolt/4-bolt SAE pump mounting flange . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Rear cover for thru-drive pump . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Pumps for shaft-up operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Foot mounting kit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Application Data
Hydraulic fluids and temperature ranges . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Fluid cleanliness . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Drive data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
3
Model Codes
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
4
Performance Data
5
Performance Data
PVH57 PVH74
Delivery and efficiency versus outlet pressure at 1800 r/min Delivery and efficiency versus outlet pressure at 1800 r/min
Delivery Delivery
Efficiency % Efficiency %
l/min (USgpm) l/min (USgpm)
Volumetric efficiency Volumetric efficiency
100 250 (66) 100 250 (66)
Overall efficiency
80 Overall efficiency 200 (53) 80 200 (53)
0 0 (0) 0 0 (0)
0 50 100 150 200 250 0 50 100 150 200 250
Outlet pressure, bar Outlet pressure, bar
0 725 1450 2175 2900 3625 0 725 1450 2175 2900 3625
Outlet pressure (psi) Outlet pressure (psi)
Input torque and power versus outlet pressure at 1800 r/min Input torque and power versus outlet pressure at 1800 r/min
Input torque Input torque
lb. ft. Nm kw (hp) lb. ft. Nm kw (hp)
(443) 600 240 (322) (443) 600 240 (322)
(295) 400 160 (215) (295) 400 Input torque 160 (215)
Input torque
(221) 300 120 (161) (221) 300 Input power, full stroke 120 (161)
Input power, full stroke
(148) 200 80 (107) (148) 200 Input power, cutoff 80 (107)
Input power, cutoff
(74) 100 40 (54) (74) 100 40 (54)
0 725 1450 2175 2900 3625 0 725 1450 2175 2900 3625
Outlet pressure (psi) Outlet pressure (psi)
6
Performance Data
PVH98 PVH131
Delivery and efficiency versus outlet pressure at 1800 r/min Delivery and efficiency versus outlet pressure at 1800 r/min
Efficiency % Delivery Efficiency % Delivery
l/min (USgpm) l/min (USgpm)
Volumetric efficiency Volumetric efficiency
100 100 250 (66)
250 (66)
20 50 (13) 20 50 (13)
0 0 (0) 0 0 (0)
0 50 100 150 200 250 0 50 100 150 200 250
Outlet pressure, bar Outlet pressure, bar
0 725 1450 2175 2900 3625 0 725 1450 2175 2900 3625
Outlet pressure (psi) Outlet pressure (psi)
Input torque and power versus outlet pressure at 1800 r/min Input torque and power versus outlet pressure at 1800 r/min
Input torque Input torque
(lb. ft.) Nm kw (hp) lb. ft. Nm kw (hp)
(443) 600 240 (322) 240 (322)
(443) 600
7
Performance Data
100
10 20 30 40 50 60 70 80 90 100
% of maximum displacement
(66) 250
(53) 200
(40) 150
(26) 100
PVH131
PVH98
(13) 50 PVH74
PVH57
(0) 0
600 1200 1800 2400
Drive speed r/min
17 bar (250 psi) _ _ _ 250 bar (3625 psi)
(psi) bar
131 98 74 57
(7.5) 0,52
Inlet pressure
(5.0) 0,35
(2.5) 0,17
(0) 0
vacuum
Inlet
(5) 127
(in Hg) mm Hg 0 400 800 1200 1600 2000 2400 2800 3200 3600
Speed r/min
8
Performance Data
9
Control Options
C or CM Pressure C or CM Control
Compensator Control Inlet
The pump will provide a continuously
modulated flow to meet changing load Case drain
demands at a pre-adjusted
To load
10
Control Options
This pump is intended for use when Pressure Compensating Without Load Sensing
multiple, remote, or electrically
Inlet
controlled compensating settings, with
or without load sensing, are desired.
Case drain
Pressure compensation is obtained
when an internal plug is removed, the Pressure
port
load-sense signal port is kept plugged,
and internal pilot pressure is applied to Tank port
the spring chamber of the control spool.
For pressure compensation with load
sensing, the internal plug stays, the
load-sense signal port is unplugged,
and pilot pressure is externally applied.
1,7 bar (25 psi)
An external relief valve (not supplied)
controls spring chamber pressure.The Outlet Load sense
externally adjustable spring determines signal port
the differential pressure setting of the To load
control. Outlet pressure is limited to the
value of the spring chamber (pressure Pressure Compensating with Load Sensing
port) pressure, plus control differential Inlet
pressure.
11
Control Options
12
Control Options
13
Input Shaft Selection Data
Maximum
Maximum thru-drive
Basic Thru-drive input output
Shaft pump pump torque torque
code Shaft designation series series Nm (lb. in.) Nm (lb. in.)
Note: Any deviation from maximum input torques must be approved by Vickers.
To assure developed thru-drive loads are within PVH pump limitations, actual
torque values must not exceed values shown.
14
Input Shaft Dimensions
E square key
A B
Spline Shafts*
Shaft Number
code Shaft designation of teeth C D
2 SAE C (J744-32-4) 14 48,0 56,0
(1.89) (2.20)
3 SAE CC (J744-38-4) 17 54,0 62,0
(2.13) (2.44)
12 SAE D (J744-44-4) 13 67,0 75,0
(2.64) (2.95)
* See torque limits on previous page.
15
Installation Dimensions
I H
G
57,25 Full R
F model: .500-13 UNC
(2.25) 45 -2B thd. 1.06 deep min.
14,53 (0.57)
57,25 14,15 (0.56) for PVH57/74. 1.19 deep
(2.25) min. for PVH98/131.
4 holes.
Drain port. SAE O-ring boss.
.500 O. D. tube, .750-16 UNF-2B thread (PVH57 & 74). M model: M12 thd. 29
.626 O. D. tube, .875-14 UNF-2B thread (PVH98 & 131). deep min. for PVH57/74.
S
2 places O 31 deep min. for
T PVH98/131. 4 holes.
48,00
(1.89)
16
Installation Dimensions
A B C D E F G H I
PVH57 76,0 71,0 293,0 216,5 171,3 86,0 79,0 88,0 69,0
(2.99) (2.79) (11.54) (8.52) (6.74) (3.39) (3.11) (3.46) (2.71)
PVH74 88,0 70,0 306,6 241,2 194,3 92,0 94,0 95,0 81,0
(3.46) (2.75) (12.07) (9.50) (7.65) (3.62) (3.70) (3.74) (3.19)
PVH98 93,1 85,0 323,5 251,3 206,1 94,5 87,5 97,1 80,1
(3.67) (3.35) (12.74) (9.89) (8.11) (3.72) (3.44) (3.82) (3.15)
PVH131 109,4 88,8 377,0 280,4 230,4 120,0 109,0 107,4 84,8
(4.31) (3.50) (14.84) (11.04) (9.07) (4.72) (4.29) (4.23) (3.34)
J K L M N O P Q R
PVH57 168,0 14,0 227,4 56,1 71,0 64,8 50,8 77,77 38,88
(6.6) (0.55) (8.95) (2.21) (2.80) (2.55) (2.0) (3.06) (1.53)
PVH74 174.0 15,0 250,1 56,0 70,0 68,0 50,8 77,77 38,88
(6.85) (0.59) (9.85) (2.20) (2.75) (2.68) (2.0) (3.06) (1.53)
PVH98 176,5 16,0 269,3 55,5 85,0 74,2 63,5 88,9 44,45
(6.95) (0.63) (10.60) (2.18) (3.35) (2.92) (2.5) (3.50) (1.75)
PVH131 202,0 15,0 298,6 62,0 88,8 70,6 63,5 88,9 44,45
(7.95) (0.59) (11.75) (2.44) (3.50) (2.78) (2.5) (3.50) (1.75)
S T U V W X Y Z
PVH57 42,88 21,44 25,4 M10x1,5 52,37 26,18 26,19 13,10
(1.69) (0.84) (1.0) (.375-16) (2.06) (1.03) (1.03) (0.52)
17
Installation Dimensions
H
G
Right hand rotation, Left hand rotation, pressure Right hand rotation,
pressure compensated compensated and load pressure compensated
and torque limit model sensing model model
A B C D* E F G H I J
PVH57 176,45 41,0 102,7 64,5 49,0 176,6 203,0 101,5 127,0 102,7
(6.95) (1.61) (4.04) (2.54) (1.93) (6.95) (7.99) (4.00) (5.00) (4.04)
PVH74 182,45 47,5 109,2 71,0 55,5 182,6 224,0 112,0 133,0 109,2
(7.18) (1.87) (4.30) (2.79) (2.19) (7.18) (8.82) (4.41) (5.23) (4.30)
PVH98 195.45 41,0 102,7 65,5 49,0 185,1 233,0 116,5 135,5 102,7
(7.69) (1.61) (4.04) (2.54) (1.93) (7.280 (9.17) (4.59) (5.33) (4.04)
PVH131 210,50 63,6 125,2 87,0 71,5 210,6 254,2 127,1 161,0 125,2
(8.29) (2.50) (4.92) (3.42) (2.81) (8.29) (10.00) (5.00) (6.37) (4.92)
*Add 16,0 (.63) to dimension D for right hand rotation model.
Pump with Pressure Compensation, Load Sense and Torque Limit Controls
A
B Optional load E
sensing signal port
J. SAE O-ring boss 62,2
for .375 O. D. tube. (2.45)
.562-18 UNF-2B
thread. D
Optional load
sensing signal port
J. SAE O-ring boss
for .375 O. D. tube.
.562-18 UNF-2B C
Left hand rotation, pressure thread. (plugged)
compensated with load sense
and torque limit model
A B C D E
PVH57 300,2 177,4 168,1 41,4 195,4
(11.82) (6.98) (6.62) (1.63) (7.69)
PVH74 322,9 200,1 174,1 47,9 201,4
(12.71) (7.88) (6.85) (1.86) (7.93)
PVH98 335,1 212,3 187,1 41,4 214,4
(13.19) (8.36) (7.37) (1.63) (8.44)
PVH131 359,5 236,6 202,2 63,8 229,5
(14.15) (9.31) (7.96) (2.51) (9.04)
18
Installation Dimensions
Tank port
4,0 (.157) Pressure port
31,0 (1.220)
25,8 (1.016)
5,2 (.205)
32,5 (1.279) 15,5 (.610)
5,0 (.197) 2 places 0,75 (.029)
21,5 (.846)
7,5 (.295)
40,5 (1.594)
A
Control surface, ISO4401 size 03. Available
with metric or UNC mounting holes to order
Access plug
C Load sense port (if used). SAE
Internal plug O ring boss for .375 O. D.
tube. .56218 UNF-2B thread
D
E
A B C D E
PVH57 234,5 72,5 269,9 128,0 142,0
(9.23) (2.85) (10.62) (5.04) (5.59)
PVH74 257,2 79,0 292,6 134,0 148,0
(10.12) (3.11) (11.52) (5.27) (5.83)
PVH98 269,3 72,5 304,7 136,5 150,5
(10.60) (2.85) (12.00) (5.37) (5.92)
PVH131 293,6 95,0 329,0 162,0 176,0
(11.56) (3.74) (12.95) (6.38) (6.93)
19
Installation Dimensions
A max
Locknut
Adjusting rod
Right hand
rotation
model.
A B C
PVH57 293,0 20,0 69.5
(11.53) (.79) (2.74)
PVH74 306,6 22,0 76,0
(12.07) (.87) (2.99)
PVH98 323,5 27,5 81,0
(12.74) (1.08) (3.19)
PVH131 377,0 37,5 88,8
(14.84) (1.48) (3.50)
20
Installation Dimensions
SAE A internal
K
involute spline. 53,20
External 9 teeth 16/32 pitch, M
involute (2.1)
E 30 pr. angle.
spline
J F G
53,20
(2.1)
53,20
H I R 1,00 (0.04) max (2.1) O 53,20
A (2.1)
B 9,00 (0.35) N
8,00 (0.31)
Right hand rotation,
For shaft options and dimensions, Note: The O-ring for sealing the rear mounting pressure compensated
see pages 14 and 15. See page 24 pad is furnished with the pump. The rear drive and load sensing model.
for optional cover for rear pad. coupling shown must be ordered separately;
see page 23
A B C D E F G H
PVH57 287,9 295,4 275.8 216,4 86,0 79,0 88,0 36,4
(11.3) (11.6) (10.86) (8.52) (3.38) (3.11) (3.46) (1.43)
PVH74 310.6 318,1 300,5 241,2 92,0 94,0 95,0 38,5
(12.23) (12.52) (11.83) (9.50) (3.62) (3.70( (3.74) (1.51)
PVH98 322,8 N/A 312,7 251,3 94,5 87,5 97,1 33,0
(12.71) (12.31) (9.89) (3.72) (3.44) (3.82) (1.30)
PVH131 347,1 N/A 337,0 280,4 120,0 109,0 107,4 35,3
(13.660 (13.27) (11.04) (4.72) (4.29) (4.23) (1.39)
I J K L M N O
PVH57 43,6 69,0 14,0 102,7 176,6 203,0 101,5
(1.72) (2.71) (0.55) (4.04) (6.95) (7.99) (4.00)
PVH74 43,8 81,0 15,0 109,2 182,6 224,0 112,0
(1.72) (3.19) (0.59) (4.30) (7.18) (8.82) (4.41)
PVH98 44,6 80,1 16,0 102,7 185,1 233,0 116,5
(1.75) (3.15) (6.30) (4.04) (7.28) (9.17) (4.59)
PVH131 44,7 84,8 15,0 125,2 210,6 254,2 127,1
(1.76) (3.34) (0.59) (4.93) (8.29) (10.0) (5.00)
21
Installation Dimensions
44,90
SAE BB size, (1.77)
side fit, internal 6 x D1
involute spline. 92,0
15 teeth 16/32 (3.62)
R 1,00
(0.04) pitch, 30 pr. 53,0
C max angle. Or SAE B 35,0 (1.38)
D (2.10)
size, side fit, 87,0 87,0 4 x D2
internal involute (3.42) (3.42)
Thru-drive pumps must have support spline. 13 teeth
located by dimension C. SAE B rear mounting. Mounting pad is machined to
16/32 pitch, 30 accept AS568-155 O-ring. Mounting pad is connected
pressure angle. to pump case and must be sealed.
D1 D2 D3
Metric M14x2,00 M12x1,75 M16x2,00
25 deep 25 deep 25 deep
Inch 0,500-13 0.500-13 0.625-11
UNC-2B UNC-2B UNC-2B
1.0 deep 1.0 deep 1.0 deep
22
Thru-drive Flange Kit and Shaft Coupling
** Thru-drive shaft couplings must be ordered separately to drive the second pump.
SAE BB PVE19/21 2
TA19 2
SAE CC PVH131 3
NOTE: The above Vickers pumps are examples of rear pumps for the thru-drive pumps dimen-
sioned on pages 21 and 22.The thru-drive torque limits identified in the chart on page 14 must
not be exceeded when applying these multiple pump systems.
23
ISO 3019/2-125B4HW Mounting Flange for PVH57 and PVH74 Pumps
Full R
56,57 56,57
(2.23) (2.23)
14,37 (.56)
14,00 (.55)
4 places
45
56,57
(2.23) 125,00
124,94
(4.921)
56,57 (4.919)
(2.23)
9,25 (.36)
SAE 2bolt/4-bolt Mounting (027 Option) for PVH57, PVH74 and PVH98 Pumps
57,25 57,25 14,53 (.57)
(2.25) (2.25) 14,15 (.56)
4 places
45
Full radius
57,25
(2.25) 127,00
126,95
17,75 (.70) (5.000)
17,37 (.68) 73,80 (4.998)
2 places 72,20
(2.90)
(2.84)
6 places
12,45 (.49)
57,25 (2.25)
90,50 Full radius
(3.56)
181,0
(7.12)
24
Pumps for Shaft-up Operation (Vertical Mount, 057 Option)
Model Dim. A
PVH57 25,68/24.94
(1.01/0.98)
73,80
72,20 PVH74 26,64/25,90
(2.90) (1.05/1.02)
(2.84) PVH98 25,82/25,08
(1.02/0.99)
Dim. A PVH131 25,12/24,38
(.99/0.96)
Attach line from this port to primary case drain line. Join
Vertical mount port. these lines at a distance above the face of the mounting
For .125 O. D. tube. flange that equals, or is less than, dimension A. Fill case
.3125-24 UNF-2B thread. with fluid up to this port prior to start-up.
1,59 (.0625) maximum
spotface depth
0,5 R
114,5 127,15 (5.006)
(4.5) 127,05 (5.002)
174,75 57,25
(6.88) (2.25)
20,5 133,0
(0.8) (5.24)
25
Application Data
26
Weights, Ordering, Installation/Start-up
27