Beruflich Dokumente
Kultur Dokumente
I BODY
B
SECTION
EXTERIOR & INTERIOR C
E
CONTENTS
PRECAUTIONS .......................................................... 2 DOOR OUTSIDE MOLDING ..................................... 16 F
Precautions for Supplemental Restraint System Removal and Installation ........................................ 16
(SRS) AIR BAG and SEAT BELT PRE-TEN- REMOVAL ........................................................... 16
SIONER .................................................................. 2 INSTALLATION ................................................... 16 G
Precautions .............................................................. 2 DOOR OUT SIDE FINISHER .................................... 17
CLIP AND FASTENER ............................................... 3 Removal and installation ........................................ 17
Description ............................................................... 3 REMOVAL ........................................................... 17
H
FRONT BUMPER ....................................................... 7 INSTALLATION ................................................... 17
Removal and Installation .......................................... 7 BACK DOOR OUTER FINISHER ............................. 18
REMOVAL ............................................................. 9 Removal and Installation ........................................ 18
INSTALLATION ..................................................... 9 REMOVAL ........................................................... 18 EI
REAR BUMPER ....................................................... 10 INSTALLATION ................................................... 18
Removal and Installation ........................................ 10 DOOR FINISHER ...................................................... 19
REMOVAL ........................................................... 10 Removal and Installation ........................................ 19 J
INSTALLATION ....................................................11 REMOVAL ........................................................... 19
FRONT GRILLE ........................................................ 12 INSTALLATION ................................................... 20
Removal and Installation ........................................ 12 BACK DOOR TRIM ................................................... 21
K
REMOVAL ........................................................... 12 Removal and Installation ........................................ 21
INSTALLATION ................................................... 12 REMOVAL ........................................................... 21
COWL TOP ............................................................... 13 INSTALLATION ................................................... 21
Removal and Installation ........................................ 13 BODY SIDE TRIM ..................................................... 22 L
REMOVAL ........................................................... 13 Removal and Installation ........................................ 22
INSTALLATION ................................................... 13 REMOVAL ........................................................... 23
FRONT STEP FINISHER .......................................... 14 INSTALLATION ................................................... 24 M
Removal and Installation ........................................ 14 Disassembly and Assembly .................................... 25
REMOVAL ........................................................... 14 REAR SIDE FRONT FINISHER .......................... 25
INSTALLATION ................................................... 14 FLOOR TRIM ............................................................ 26
DRIP MOLDING ........................................................ 15 Removal and Installation ........................................ 26
Removal and Installation ........................................ 15 REMOVAL ........................................................... 26
REMOVAL ........................................................... 15 INSTALLATION ................................................... 26
INSTALLATION ................................................... 15 HEADLINING ............................................................ 27
Removal and Installation ........................................ 27
REMOVAL ........................................................... 30
INSTALLATION ................................................... 31
EI-1
PRECAUTIONS
PRECAUTIONS PFP:00001
Precautions for Supplemental Restraint System (SRS) AIR BAG and SEAT
BELT PRE-TENSIONER EIS001JC
The Supplemental Restraint System such as AIR BAG and SEAT BELT PRE-TENSIONER, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. Information necessary to service the system safely is included in the SRS and SB section of
this Service Manual.
WARNING:
To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death
in the event of a collision which would result in air bag inflation, all maintenance must be per-
formed by an authorized NISSAN/INFINITI dealer.
Improper maintenance, including incorrect removal and installation of the SRS, can lead to per-
sonal injury caused by unintentional activation of the system. For removal of Spiral Cable and Air
Bag Module, see the SRS section.
Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this
Service Manual. SRS wiring harnesses can be identified by yellow harness connectors.
Precautions EIS001JD
When removing or disassembling any part, be careful not to damage or deform it. Protect parts, which
may get in the way with cloth.
When removing parts with a screwdriver or other tool, protect parts by wrapping them with vinyl or tape.
Keep removed parts protected with cloth.
If a clip is deformed or damaged, replace it.
If an unreusable part is removed, replace it with a new one.
Tighten bolts and nuts firmly to the specified torque.
After re-assembly has been completed, make sure each part functions correctly.
Remove stains in the following way.
Water-soluble stains:
Dip a soft cloth in warm water, and then squeeze it tightly. After wiping the stain, wipe with a soft dry cloth.
Oil stain:
Dissolve a synthetic detergent in warm water (density of 2 to 3% or less), dip the cloth, then clean off the stain
with the cloth. Next, dip the cloth in fresh water and squeeze it tightly. Then clean off the detergent completely.
Then wipe the area with a soft dry cloth.
Do not use any organic solvent, such as thinner or benzine.
EI-2
CLIP AND FASTENER
Clips and fasteners in EI section correspond to the following numbers and symbols.
B
EI
EI-3
CLIP AND FASTENER
Replacce any clips and/or fasteners which are damaged during removal or installation.
SIIA0315E
EI-4
CLIP AND FASTENER
EI
SIIA0316E
EI-5
CLIP AND FASTENER
SIIA0317E
EI-6
FRONT BUMPER
EI
EI-7
FRONT BUMPER
Bumper fascia is made of plastic. Do not use excessive force and be sure to keep oil away from it.
PIIA0428E
EI-8
FRONT BUMPER
REMOVAL
1. Remove front grille. Refer to EI-12, "FRONT GRILLE" . A
2. Remove bumper fascia installation nuts at front bumper stay assembly. A
3. Remove installation bolt of bumper fascia center. B
B
4. Remove bumper fascia installation clip at front side member. C
5. Remove installation nut on the lower LH/RH of bumper fascia. D
6. Remove side combination lamp. Refer to LT-23, "Removal and Installation for Front Turn Signal Lamp" .
C
7. Remove bumper fascia installation bolt and nut from right and left front fender. E
8. Remove bumper fascia assembly.
INSTALLATION D
To install, reverse the removal procedure sequence.
After installation, adjust the clearance.
E
EI
EI-9
REAR BUMPER
Bumper fascia is made of plastic. Do not use excessive force and be sure to keep oil away from it.
PIIA0429E
REMOVAL
1. Remove bumper fascia installation clip. A
2. Remove dove tail and bumper fascia installation clip. B
3. Remove rear center clips of rear bumper step. C
4. Remove installation bolt at the bottom of bumper fascia. D, E
EI-10
REAR BUMPER
5. Pull bumper fascia side area toward outside, and remove it from
side clips. F A
6. Remove bumper fascia.
PIIA0430E
D
INSTALLATION
To install, reverse the removal procedure sequence.
After installation, adjust clearance. E
EI
EI-11
FRONT GRILLE
PIIA0431E
REMOVAL
1. Remove grille mounting screw.
2. Using a flat-bladed screwdriver, disengage turn fastener from
grille, and remove grille.
NOTE:
Remove turn fastener remaining on vehicle using long-nose pli-
ers or the like.
PIIA0432E
INSTALLATION
1. Install turn fastener to grille.
2. Install grille to vehicle, and install screws.
EI-12
COWL TOP
REMOVAL
B
G
PIIA0433E
1. Remove wiper arms (LH/RH) from the vehicle. Refer to WW-6, "Removal and Installation for Front Wiper
Arms, Adjustment for Wiper Arms Stop Location" . H
2. Remove cowl top cover mounting clips and hooks.
3. Disconnect washer hose from the connector, and remove cowl top cover.
EI
INSTALLATION
To install, reverse the removal procedure sequence.
J
EI-13
FRONT STEP FINISHER
PIIA0436E
REMOVAL
1. Remove front bumper fascia. Refer to EI-7, "FRONT BUMPER" .
2. Remove step finisher mounting clips (upper 2, side 1).
3. Remove step finisher mounting clips (blind clip: 2), and remove step finisher.
INSTALLATION
To install, reverse the removal procedure sequence.
EI-14
DRIP MOLDING
PIIA0434E G
REMOVAL
1. Using a clip clamp tool, disconnect drip molding connector. H
2. Insert clip clamp tool into drip molding lower joint, and remove drip molding.
(Remove front drip molding from the rear end, and remove rear drip molding from the front end.)
INSTALLATION EI
To install, reverse the removal procedure sequence.
After installation, make sure there is no poor mating or looseness with drip molding.
J
EI-15
DOOR OUTSIDE MOLDING
PIIA0435E
REMOVAL
1. Fully open front door window.
2. Remove front door finisher. Refer to EI-19, "DOOR FINISHER" .
3. Remove corner cover and door mirror. Refer to GW-21, "DOOR MIRROR" .
4. Lift up the front end of door outside molding, and lightly twist it toward the outside to engage clips. Then
remove door outside molding.
INSTALLATION
To install, press door outside molding into the door outer panel flange and engage the clips.
EI-16
DOOR OUT SIDE FINISHER
REMOVAL
1. Remove front door trim. Refer to EI-19, "DOOR FINISHER" .
B
2. Remove corner cover inner (Clip: 3).
3. Remove mounting bolts, and remove door outside finisher.
C
PIIA0497E
E
INSTALLATION
To install, reverse the removal procedure sequence.
F
EI
EI-17
BACK DOOR OUTER FINISHER
PIIA0437E
REMOVAL
1. Remove back door trim. Refer to EI-21, "BACK DOOR TRIM" .
2. Disconnect license lamp harness connector.
3. Remove back door outer finisher mounting nuts and clips, and remove back door outer finisher.
INSTALLATION
To install, reverse the removal procedure sequence.
EI-18
DOOR FINISHER
EI
SIIA1012E
K
1 Sliding door upper garnish 2 Sliding door inside handle 3 Sliding door finisher
4 Stopper 5 Armrest 6 Power window switch finisher
7 Inside handle escutcheon 8 Front door finisher L
REMOVAL
Front Door Finisher M
1. Remove inside handle escutcheon.
NOTE:
1. Using a clip clamp remover, disengage hooks at front, top,
and bottom of escutcheon.
2. Slide toward rear of the vehicle, and disengage the hook at
rear end for removal.
SIIA1070E
EI-19
DOOR FINISHER
SIIA0981E
PIIA0526E
NOTE:
Insert a clip remover or clip clamp remover between body-side panel and clip, and remove finisher.
INSTALLATION
Install in the reverse order of removal.
NOTE:
To install the finisher, confirm clips are accurately aligned with the holes on the body side panel, then press in.
EI-20
BACK DOOR TRIM
EI
SIIA1013E
REMOVAL
1. Remove back door inside handle (screw: 1). K
2. Remove back door inside handle escutcheon (screw: 2).
3. Remove pull handle (bolt: 1).
4. Remove back door finisher mounting clips, and remove back door finisher. L
5. Remove back door upper finisher mounting clips, and remove back door upper finisher.
NOTE:
Insert a clip driver or clip clamp remover into the part shown by the M
arrow (between the clips and the body side panel). Remove clips.
PIIA0527E
INSTALLATION
Install in the reverse order of removal.
NOTE:
When installing, confirm clips are accurately aligned with the holes on the body side panel, then press in.
EI-21
BODY SIDE TRIM
SIIA1014E
EI-22
BODY SIDE TRIM
REMOVAL
Front Pillar Garnish E
1. Remove assist grip.
2. Pull front pillar garnish toward the inside and disengage metal clips on the back. Then remove it.
F
Roof Side Center Garnish
Disengage metal clips on the back and remove it.
Kick Plate G
1. Remove mounting screws.
2. Pull up kick plate, and remove resin clips on the back. Then remove it.
H
Center Pillar Lower Garnish
1. Remove seat belt floor anchor bolt. Refer to SB-5, "Second Seat Belt" and SB-7, "Third Seat Belt, Fourth
Seat Belt and Fifth Seat Belt" in H Passenger Protective System.
EI
2. Remove partition pipe and partition bracket.
3. Remove engine cover stay mounting bolts (LH) and strap from left side.
4. Pull center pillar lower garnish straight toward the inside and disengage metal clips on the back. Then J
remove it.
NOTE:
When removing left side of center pillar lower garnish, wrap a cloth around engine cover stay to protect it from K
scratches and damages.
Center Pillar Upper Garnish
1. Remove seat belt shoulder anchor bolts. Refer to SB-5, "Second Seat Belt" and SB-7, "Third Seat Belt, L
Fourth Seat Belt and Fifth Seat Belt" in H Passenger Protective System.
2. Pull center pillar upper garnish straight toward the inside and disengage metal clips on the back. Then
remove it. M
Rear Pillar Center Garnish (Four-Door Model)
Disengage clips engaging with rear pillar upper garnish, and pull rear
pillar center garnish toward the inside to remove it.
SIIA1015E
EI-23
BODY SIDE TRIM
EI-24
BODY SIDE TRIM
D
SIIA1016E
EI
EI-25
FLOOR TRIM
SIIA1017E
REMOVAL
1. Remove front seat and rear seat. Refer to SE-6, "Removal and Installation" and SE-13, "Removal and
Installation" in SE Seat.
2. Remove carpet hook.
3. Remove footrest.
4. Remove selector lever knob and console boot (screw: 2, clip: 1). (only for M/T vehicle)
5. Remove kick plates (LH/RH).
6. Remove center pillar lower garnishes (LH/RH).
7. Remove rear side front finishers (LH/RH) and rear side rear finishers (LH/RH).
8. Remove back pillar lower garnishes (LH/RH).
9. Remove step trim.
10. Remove front floor carpet (fixing hook: 6).
11. Remove engine cover carpet.
12. Remove bulkhead carpet (fixing hook: 9).
13. Remove rear end kick plate.
14. Remove rear floor carpet (fixing hook: 3).
NOTE:
For steps 5 to 9, refer to EI-22, "Removal and Installation" in EI Exterior/Interior.
INSTALLATION
Install in the reverse order of removal.
EI-26
HEADLINING
HEADLINING PFP:73910
A
Removal and Installation EIS0019N
EI
K
SIIA1019E
EI-27
HEADLINING
SIIA1025E
SIIA1058E
1 Headlining (front: molded) 2 Rear ventilator grilles (LH/RH) 3 Rear air conditioner switch
4 Assist grip 5 Rear intake grille (RH/center/LH) 6 Headlining (center: built-in)
7 Headlining (rear: built-in) 8 Roof bow 9 Interior lamp
EI-28
HEADLINING
SIIA1057E EI
1 Headlining 1st 2 Headlining 2nd 3 Headlining 3rd
4 Headlining 4th 5 Headlining 5th 6 Assist grip
7 Roof bow bracket (RH) 8 Roof bow bracket (LH) 9 Roof bow J
EI-29
HEADLINING
SIIA1026E
1 Windshield upper welt 2 Windshield upper bracket 3 Rear intake grille (center)
4 Headlining 5 Headlining listing wire 6 Wire holder
7 Assist grip 8 Rear air conditioner cover 9 Rear air conditioner cover bracket
(front)
10 Rear intake grille (LH/RH) 11 Rear ventilator grilles (LH/RH) 12 Rear air conditioner cover bracket
(rear)
13 Interior lamp housing 14 Lens (interior lamp) 15 Luggage compartment lamp housing
16 Lens (luggage compartment lamp)
REMOVAL
1. Remove partition pipe and partition bracket. (Only for van)
2. Remove front pillar and center pillar garnish. (Only for vehicle with rear air conditioner)
3. Remove roof side center garnish. (Only for built-in ceiling model)
4. Remove front body side welt and sliding door weatherstrip. Only for molded ceiling model and sus-
pended ceiling model (except van)
5. Remove rear pillar upper garnish and back pillar upper garnish. Only for molded ceiling model and sus-
pended ceiling model (except van)
6. Remove center body side welt and rear body side welt. Only for molded ceiling model and suspended
ceiling model (except van)
NOTE:
For steps 2 to 6 shown above, refer to EI-22, "Removal and Installation" in EI Exterior/Interior.
7. Remove assist grip.
EI-30
HEADLINING
SIIA1023E
D
9. Remove inside mirror.
G
SIIA1024E
10. Remove map lamp, interior lamp, and luggage compartment lamp. Refer to LT-40, "Removal and Installa- H
tion" (interior room lamp, spot lump and luggage room lamp) in LT Lighting System.
11. Remove rear air conditioner cover and rear air conditioner cover brackets (front and rear). (Only for sus-
pended ceiling model) EI
12. Remove roof bow. (Only for built-in ceiling model)
13. Remove headlining mounting clips, and remove headlining from the back door opening.
J
NOTE:
Removal and installation must be performed by two persons.
K
Do not strongly bend the headlining.
INSTALLATION
Install in the reverse order of removal. L
EI-31
HEADLINING
EI-32