NASI
AAJIYA JETRIB
METAL ROOFING SYSTEM
TRAPEZOIDAL PROFILEAAJIYA
AJIYA JET RIB INDUSTRIAL PROFILE METAL ROOFING
+ Roll - forming long length high tensile metal decking.
+ Manufactured from high tensile steel substrate protected with corrosion inhibitive treatment.
+ Roofing and walling profiles with material warranty up to 25 years™. * Warranty terms & conditions apply.
+ With effective cover width of 720mm and rib height of 23mm.
+ For minimum roof pitch of 3°.
+ Innovative, durable and cost effective.
+ Widely used for commercial and industrial projects such as factories, condominium, cabin, hoarding, and etc.
SECTIONAL PROFILE
LY. IIT ES
Dimensions Tolerence
Rib height 23mm Thickness for material: £0.03mm
Effective cover: 720mm Effective Width 3mm
Minimum roof pitch : 3° Finishing Length: + Smm
It is strongly recommended that AJIYA
JET RIB are laid with the side laps
facing away from the direction of the
prevailing wind. Where possible, the
roof sheets should be fixed with the side
laps facing away from the mormal line
a er, Somm Tacks aac Dousesioe ——ouccenvare P
gttatewen itn oesSer SRUMOMOR NEVA StS of sight
woot rene cuss
SIDE LAP fasteners are required at
mid spans for purlin spacings over
1,000mm and fo git spacings over
1,200mm for all side lap and flashing
amamasosue fastening, use no. 10 x 25mm. self
Gomnvzram — drilling Hexagon Head Screw with
pre-assembled neoprene bonded steel
washer.
END LAP AJIYA JET RIB is available
in continuous length limited only by the
maximum transportable length of 20m.
For longer length, end lap is necessary.
‘Minimum end lap should be 200mm and
for roof pitches below 8°, the lap should
be treated with a recommended sealant.
emery TRC cee mre ene ect
Ersoy ects ae er SS Cees TCE ce RC CSCC SeAAJIYA
TECHNICAL SPECIFICATIO!
AVAILABLE THICKNESS
ata
en
1 )
JET RIB i)
0.35 040) 2.65 3.68 272 ASTM A446-E 550
0.42 0.48 3.18 442 315 ASTM A446-E 550
0.48 0.55 3.61 5.01 200 ASTM A446-E 550,
ailable on request. Please refer to our technical department
howe is depending on material used.
* Weight show
RECOMMENDED MAXIMUM SPACING OF SUPPORTS
Total Coated 5
eed
" Thickness
ru oe ane Pues Sar tisetigeca
a) ini (mm) co) on co)
0.35 040 1330 1700) 1900) 2400)
0.42 0.48 1700 2100 200 2600
0.48 0.55 2700 2700 2600 2900
RECOMMENDED MAXIMUM ROOF LENGTH (M)
RAINFALL (mm/h)
150 50 60 80
200 39 50 60.
250 30 40 48
300 26 30 40
The recommended minimum fall is 3°. However it must be remembered that the amount of water that must be
shed increases with the length of the roof. Therefore, to avoid possible back up of water in serve wind conditions,
the following recommended roof length should be considered as maximum for a given roof pitch and rainfall
rate,
ESDXMIN GG
a ee 5 ees eae
CREST FIXING OF AJIYA JET RIBINS INAN SVAN DINRIDICNE RIN G/BIENS HIN G:
RIDGE CAPPING TYPE 24
HIP CAPPING TYPE 18
RIDGE CAPPING TYPE 18
HIP CAPPING TYPE 12
FLASHING TYPE 18a FLASHING TYPE 12a
FLASHIN'
fe,
Ve
'YPE 18b
FASCIA/BARGE CAPPING TYPE 18
PE 12
VALLEY TRAY TYPE 24 VALLEY TRAY TYPE 18
NA
www.ajiya.com
Corporate Head Office & Factory
eee uc
cee)
Dre eran
Ree ere ar)
Coed
cere rca
Peco)
Cee ey
ie
Core coe
Mentakab Marketing Office
Pee
Recent
ees
PE Cae
ee es tare arc)
ord
cree
coerce tea
Perera]
Eee
Esra ea
Eras
Coote ier
eer)
Pare reer)
eS
SEO ce eae)
reer
Paecc no
Beasts
a
TO BUILD
aU {
Cee ahs
day