Beruflich Dokumente
Kultur Dokumente
ABSTRACT
For strengthening and rehabilitating of RCC beams, the utilization of externally bonded fiber
reinforced polymer sheets has been found effective. To increase the load carrying capacity of the
structural beam as well as to increase the service life of the beam retrofitting with FRP sheets
especially GFRP sheets found most suitable and economical.
This paper is intended for experimental studies of damaged reinforced concrete beams repaired
by bonding of Glass fiber reinforced polymer (GFRP) overlays to the beam. The three sets of beams
has to be tested in this study: control beams (without GFRP overlays) and damaged and then
repairing beams with GFRP overlays by varying different parameters (damage degree, GFRP
overlay width,). All beams have to be tested under simply supported condition. The testing has to be
done under two point loading using the load frame over a span of 1500 mm. The tests were carried
out under displacement control. The most investigated parameter in this experimental study is to
determine increase in load carrying capacity of strengthened beam. To evaluate the strength of
damaged RC beams with externally bonded GFRP laminates was the target of this project.
Key words: Strengthening; composite materials; GFRP Overlays; RC Beams Flexural and Shear
strengthening; Load tests.
Cite This Article: T. P. Meikandaan and Dr. A. Ramachandra Murthy, Retrofittng of Reinforced
Concrete Beams Using GFRP Overlays. International Journal of Civil Engineering and Technology,
8(2), 2017, pp. 410417.
http://www.iaeme.com/IJCIET/issues.asp?JType=IJCIET&VType=8&IType=2
1. INTRODUCTION
Reinforced Cement Concrete is very popular construction material used for structural components of a
building like beams, columns and slabs etc. One major flaw of RCC is its susceptibility to environmental
attack. This can severely decrease the strength and life of the structures. The repair of structurally deteriorated
RC Structures become necessary since the structural element ceases to provide satisfactory strength and
serviceability.
There are considerable number of existing concrete structures in India that do not meet current design
standards. because of inadequate design and construction . They need structural up gradation to meet new
seismic design requirements. The reasons for loss of strength may be due to changes in loading, reinforcement
corrosion, construction errors, additional loadings or changes in configuration or accidents such as earth
quakes or due to fire etc. There are many methods for flexural strengthening, such as: section enlargement,
steel plate bonding, external post tensioning method, externally bonded system (EBS) and near-surface
mounted (NSM) system. While many methods of strengthening structures are available, strengthening
structures via external bonding of advanced fiber-reinforced polymer composite (FRP) has become very
popular worldwide
The development of strong epoxy glue has lead to a technique which has great potential in upgrading
structure by retrofitting. Reinforced Concrete structures using externally bonded Fiber Reinforced Polymer
(FRP) composites. It has become a very universal practice, extensively accepted. In Particular the Flexural
Strength of a reinforced concrete beam can be extensively increased by application of carbon (CFRP), Glass
(GFRP) and Aramid (AFRP) . FRP Plates /sheets adhesively bonded to the tension face of the beams for
increasing the flexural strength of the beams. And also bonded to the vertical faces for increasing the shear
strength.
2. AIM
The major aim of the project is to study the behavior of R.C.C. beams retrofitted with GFRP overlays so that
to obtain best procedures for strengthening of R.C.C. beams using GFRP overlays. To improve the load
carrying capacity of the R.C.C Beam using GFRP overlays is the aim of the project.
3. OBJECTIVES
The objective is achieved by conducting the following task
1. To improve the load carrying capacity of both shear deficient beams and flexural deficient beams by retrofitting
with GFRP
2. To study the load deflection behavior of flexural deficient beams which are retrofitted with GFRP
3. To study the ductility of flexural deficient beams
4. To study the effect of different sized layers of GFRP, which can be wrapped on flexural deficient beams
5. To compare the strength of various sizes of GFRP sheetswhich can be wrapped on beams
4. SCOPE OF STUDY
It is essential to study the shear carrying capacity, Flexural carrying capacity and ductility of flexural beams
by retrofitting with GFRP. The effect of increasing the number of layers of GFRP has to be studied. Load
carrying capacity corresponding to the number of layers of GFRP should be studied for both shear deficient
beams and Flexural deficient beams.
The investigations as well as studies conducted on the retrofitting of the RCC beams using Glass fiber
reinforced polymer overlays are limited. So it is essential to study the shear carrying capacity, Flexural
carrying capacity and ductility of flexural beams by retrofitting with GFRP. The effect of different sized
layers of GFRP, which can be wrapped on shear and flexural deficient beams has to be studied. Load carrying
capacity corresponding to the number of layers of GFRP should be studied for both shear deficient beams
and Flexural deficient beams.
Although the fibers and resins used in FRP Systems are relatively more expensive compared with
traditional strengthening materials, labour and equipment costs to install FRP systems are often lower.
6. TYPES OF FRPS
Depending on the type of fibers used, FRP composites are classified into three types:
1. Glass FRP composites (GFRP)
2. Carbon FRP composites (CFRP)
3. Aramid FRP composites (AFRP)
7. GFRP SHEETS
Application of GFRP overlays is the one of the simplex methods for retrofitting the existing structures. GFRP
has high strength ratio high stiffness to weight ratio, flexibility in design, non corrosiveness and lower
density.
The objective of the GFRP wrapping is to improve the flexural strength and stiffness of deficient beams
.Beams are the main structural elements need to be rehabilitated when fracture or fault is noticed. The faulty
beam can de strengthened by the GFRP wrapping. The GFRP sheets can be joined on site in to complicated
shapes and also can be easily cut to required length on site.
8. GFRP OVERLAYS
The fiber system used in GFRP consists of different types of architectures of fiber materials. The raw fiber
is processed and supplied in a strand form on a spool and known as roving or in broad goods form on a roll
and is known as mat. The common types of GFRP over lays are
9. METHODLOGY
The procedure of investigation was shown by the flow chart as detailed below:
LITERATURE REVIEW
DATA COLLECTION
Grades of concrete, M20 Design mix, Degree of workability, Type & size of aggregates and IS codes
PRELIMINARY TESTS
CASTING OF BEAMS-
,
TESTING
1. Ductility, 2. First cracking and ultimate loads, 3 Load-deflection
CONCLUSION
10.4. WATER
Clean portable water available in the laboratory of university which satisfies the drinking standards was used
for the preparation of specimens.
1 4.75 0 0 0 100
2 2.36 21 2.1 2.1 97.9
3 1.18 122 12.2 14.3 85.6
4 600 u 286 28.6 42.9 57.1
5 300 u 512 51.2 94.1 5.9
6 150 u 59 5.9 100 0
Total 1000 253.4
As 57.1% passed through 600 micron sieve ,according to IS 383-1970 confirms Zone-II.
11.6. WATER
The tap water available in the campus was tested for its suitability. Necessary properties such as pH value,
chloride content, total hardness and total dissolved solids were evaluated and are given in Table 3.6.
Obtained Permissible value
Sl.no. Description
value as per IS 456-2000
1. pH value 8.2 Not less than 6.0
2. Chloride content 112.5 mg/l 500 mg/l*
3. Total hardness 105 mg/l 200 mg/l
12.5. Test Results of70% Preloaded Set2 Flexure Beams Wrapped with 50mm Wide GFRP
Sheet For Fulllength
Three flexure beams (F4,F5,F6) wrapped with 50mm wide GFRP sheet for full length of the beam in the
tension zone i.e at bottom of the beam ,were tested for ultimate load carrying capacity .
TEST READINGS OF 70% PRE LOADED SET 2 BEAMS WITH 50MM WIDE GFRP STRIP FOR
FULL LENGTH
SAMPLE F4 F5 F6
Pre Load 42 kN 42 kN 42 kN
Load in kN LVDT 1 in LVDT2 in LVDT 1 in LVDT2 LVDT 1 in LVDT2 in
0 0 0 0 0 0 0
5 0.1 0.1 0.1 0.1 0.1 0.2
10 0.2 0.3 0.3 0.4 0.3 0.3
15 0.3 0.3 0.4 0.4 0.3 0.5
20 0.5 0.6 0.5 0.6 0.4 0.7
25 0.6 0.6 0.6 0.6 0.7 0.8
30 0.6 0.7 0.7 0.8 0.8 0.8
35 0.8 0.8 0.8 0.8 0.9 1
40 0.9 1 0.9 1 1.1 1.2
45 1 1.1 1 1.1 1.2 1.4
50 1.3 1.4 1.1 1.3 1.3 1.6
55 2.1 2.2 1.3 1.5 2.1 2.3
60 2.2 2.3 1.6 1.8 2.3 2.4
65 2.5 2.6 2.4 2.5 2.6 2.8
58 3.5 3.7 3.8 3.9 3.6 3.9
50 3.7 3.8 4.1 4.1 3.8 4.1
49 3.7 3.8 4.2 4.3 3.9 4.1
12.6. Test Results Preloaded (70% Of Ultimate Load) Set3 Flexure Beams Wrapped with
400mm Length GFRP Sheet For Full width At The Middle of Beam At Bottom
Three flexure beams (F7,F8,F9) wrapped with GFRP sheet of full width for 400 mm length in the tension
zone i.e at middle bottom of the beam ,were tested for ultimate load carrying capacity .
TEST READINGS OF 70% PRE LOADED SET 3BEAMS WITH FULL WIDTH FOR
CENTRAL
SAMPLE 400MM
F7 LENGTH F8 F9
Pre Load 42 kN 42 kN 42 kN
Load in kN LVDT 1 in LVDT2 LVDT 1 in LVDT2 LVDT 1 LVDT2 in mm
0 mm
0 in
0 mm mm
0 in
0 mm in
0 mm 0
5 0.1 0.1 0.1 0.2 0.2 0.2
10 0.2 0.3 0.3 0.3 0.4 0.5
15 0.3 0.4 0.4 0.5 0.5 0.6
20 0.4 0.4 0.4 0.6 0.5 0.7
25 0.5 0.6 0.6 0.7 0.6 0.8
30 0.6 0.7 0.7 0.8 0.7 0.9
35 0.7 0.8 0.7 0.9 0.8 1
40 0.9 1.1 1 1.1 0.9 1.2
45 1.2 1.4 1.2 1.3 1.1 1.3
50 2.3 2.6 2.4 2.8 2.5 2.9
48 3 3.2 3.1 3.4 3.3 3.5
44 3.9 4 3.9 4.1 3.8 4
13. DISCUSSIONS
In this part of chapter the experimental results of SET I beams (Control Beam) and SET 2 and SET 3 beams
(weak in flexure),their behavior throughout the static test to failure is described using recorded data on
deflection behavior and the ultimate load carrying capacity. The crack patterns and the mode of failure of
each beam are also described in this chapter.
Three sets of beams were tested for their ultimate strengths. In SET I three beams (F1, F2 and F3) were
tested for their ultimate strengths. In SET 2 three beams (F4, F5 and F6) were tested for 70% of pre ultimate
load and also. SET 3 three beams (F7, F8 and F9) were tested for 70% of pre ultimate load.
Table 13.6 Ultimate Loads, Deflections and Nature of failure for SET I , SET2,SET 3 beams
Load at Average
Beam initial Ultimate Deflection at
Sr.No Type of Beam Nature of failure
designation crack Load (KN) Ultimate load
(KN) in mm
F1 20 60 12.05 Flexural failure
F3 15 59 10.85
F6 20 42 3.35
2 Pre Loaded Beams
F7 20 42 3.55
F8 20 42 3.25
F9 20 42 3.10
Not GFRP Flexural
F4 65 2.55
GFRP Wrapping Visible failure
With 50mm strip at Not
3 F5 65 2.45
bottom for full Visible
length Not
F6 65 2.70
Visible
Not GFRP Flexural
F7 50 2.45
GFRP Wrapping Visible failure
With 400 mm Not
4 F8 50 2.6
length at middle for Visible
full width Not
F9 50 2.7
Visible
25
Deflection in mm
20
15
LVDT1 in mm
10
LVDT2 in mm
5
0
0 20 40 60 80
Load in kN
25
Deflection in mm
20
15
LVDT1 in mm
10
LVDT2 in mm
5
0
0 20 40 60 80
Load in kN
18
16
14
Deflection in mm
12
10
LVDT1 in mm
8
6 LVDT2 in mm
4
2
0
0 50 100
Load in kN
4
3.5
3
Deflection in mm
2.5
2 LVDT 1 in
mm
1.5
LVDT2 in
1
mm
0.5
0
0 50 100
Load Deflection Curve For F4 Wrapped With 50mm Strip For Full Length At Bottom
3 LVDT 1 in
2 mm
LVD2 in
1
mm
0
0 50 100
Load in kN
Load Deflection Curve For Beam F5 Wrapped With 50mm Strip For Full Length At Bottom
4.5
4
3.5
3
2.5 LVDT 1 in
2 mm
1.5
LVDT2 in
1
mm
0.5
0
0 50 100
Load in kN
Load Deflection Curve For Beam F6 Wrapped With 50mm Strip For Full Length At Bottom
4.5
4
3.5
Dmmeflection in mm
3
2.5
2 LVDT 1 in
mm
1.5
1 LVDT2 in mm
0.5
0
0 20 40 60
Load in kN
Load Deflection Curve For Beam F7 With Full Gfrp Strip For 400mm Length At Middle of Beam
4.5
4
3.5
Deflection in mm
3
2.5 LVDT 1 in
2 mm
1.5 LVDT2 in
1 mm
0.5
0
0 20 40 60
Loa d in kN
Load Deflection Curve For Beam F8 With Full Width Gfrp Strip For 400mm Length At Middle Of The Beam
4.5
Deflection in mm
4
3.5
3
2.5
LVDT 1 in
2 mm
1.5
1 LVDT2 in
0.5 mm
0
0 20 40 60
Load in kN
Load Deflection Curve For Beam F9 With Full Gfrp Strip For 400mm Length At Middle Of Beam
14. CONCLUSIONS
In this project investigations were made on the flexural behavior of reinforced concrete beams
strengthened with different sizes of GFRP sheets and outcomes are studied. From test results necessary
observations were made and, the following conclusions are drawn:
1. The ultimate load bearing capacity of beam F4 wrapped with 50 mm wide GFRP for full length is increased
by 8.33%
2. The ultimate load bearing capacity of beam F5 wrapped with 50 mm wide GFRP for full length is increased
by 10.16%
3. The ultimate load bearing capacity of beam F6 wrapped with 50 mm wide GFRP for full length is increased
by 10.16%
4. It is found that, retrofitting of preloaded beam with GFRP of 50mm wide for full length of the beam at
bottom of the beam resulted 10% increase in ultimate load bearing capacity
5. The Deflection of the beam F7,f8,f9 wrapped with GFRP sheet of full width of beam for a length of 400mm
at the middle bottom of the beam is reduced to greater extent
6. It is found that deflection was reduced to great extent in the case of SET 3 beams wrapped with GFRP
overlays in the middle bottom of the beams
7. Use of GFRP overlays improves load carrying capacity; delays crack formation and energy absorption
capability of beam .Reduced deflection indicates the increase in stiffness
8. RCC pre loaded beams wrapped with 50mm wide GFRP overlay for full length of beam shown better
performance in reducing deflection than beams wrapped with GFRP overlays of 400mm length at
middle bottom of the beam
REFERENCES
[1] Ahmed .Md Vazeer et al (2014) Experimental studies on Retrofitting of RCC Beams using GFRP,
International Journal of Research in Science and Technology (IJRST),ISSN-2349-0845 .
[2] Deepa A. Sinha (2012), Strengthening of Structures using with Glass Fiber Reinforced Polymer sheet,
Volume:1 Issue:5 ,ISSN No.2277-8160
[3] Deepak Kumar et al (2015) Use of GFRP ( Glass Fiber Reinforced Polymer) for Strengthening of
Reinforced Concrete Beam , SSRG International Journal of Civil Engineering (SSRG-IJCE) ISSN-2348-
8352.
[4] Jaya. K.P et all (2012) Strengthening of RC Column using GFRP and CFRP, 15WCEE
[5] Jameel Md. Akthar (2013) Re strengthening of RCC Beam by Beam Jacketing , Malaysian Journal of Civil
Engineering 25(2)
[6] Jeya Bharathy.A.S. et al (2013) Experimental Investigation on Behavior of R.C.C. Beam Retrofitted with
sisal Fiber Sheet , International Journal of Innovative Research in Science, Engineering and Technology,
ISSN 2319-8753
[7] Kaushal Parikh et al (2012) Application of GFRP on preloaded beam for enhancement in flexural
strength.IJCSE Journal. ISSN-0976-4399
[8] Lokesh A. Doddamani et al (2014) The Study on strength and Stiffness of RC Beams retrofitted with GFRP
wrapping, International Journal of Engineering Research and Technology (IJERT) ISSN 2278-0181.
[9] Murali.G.et al(2011) Flexural Strengthening of Reinforced Concrete Beams using Fiber Reinforced
Polymer Laminates, ARPN Journal of Engineering and Applied Sciences,ISSN-1819-6608
[10] Muthuramu.K.L et al (2010) on strengthening of RC beams externally Bonded with Glass Fiber Reinforced
Polymer sheets.
[11] Nachimuthu.S et al (2015) Strengthening of Corroded RC Beam using Hybrid FRP wrapping Technique,
Integrated Journal of Engineering Research and Technology ,ISSN No. 2348-6821
[12] Namasivayam. Aravind(2013) Retrofitting of Reinforced Concrete beams using Fiber Reinforced Polymer
(FRP) Composites<journal of Urban and Evironmental Engineering Volume 7 ISSN 1982-3932
[13] Naveen.S et al(2015) Study on Torsional behavior of TC-T beams strengthened with Glass FRP, Research
Journal of Recent Sciences ISSN-2502.
[14] Polu Raju .Pet al (2011) Experimental Evaluation of Retrofitted Concrete Beams using CFRP and GFRP,
International Journal of Earth Sciences and Engineering ,ISSN 0974-5904
[15] Rahul Kumar Satbhaiya et al(2013) Rehabilitation and Strengthening of RCC Structures by Using FRP
Composites, International Journal of Engineering Technology and Advanced Engineering, ISSN- 2250-
2459.
[16] Sandeep G.Sawant et al (2013) Strengthening of RCC Beam- Using different glass fiber, International
Journal of Inventive Engineering and Sciences(IJIES) ISSN 2319-9598
[17] Sandeep Kumar.L.S et al ( 2013) Retrofitting of RC Beams using natural FRP wrapping
(NSFRP),International Journal of Emerging Trends in Engineering and Development ,Issue3 Volume 5 ,
ISSN 2249-6149.
[18] Pinal C. Khergamwala, Dr. Jagbir Singh and Dr. Rajesh Kumar, Experimental Study on Shear Behavior
of Reinforced Recycled Aggregate Concrete Beams, International Journal of Civil Engineering and
Technology, 7(2), 2016, pp. 128139.
[19] Aamer Najim Abbas, Ali Sabah Ahmed and Saad Khalaf Mohaisen, Rehabilitation of Normal and Reactive
Powder Reinforced Concrete Beams Using Epoxy Injection Technique, International Journal of Civil
Engineering and Technology, 7(3), 2016, pp. 3142.
[20] P. Uday Kumar and B. Sarath Chandra Kumar, Flexural Behaviour of Reinforced Geopolymer Concrete
Beams with GGBS and Metakaoline. International Journal of Civil Engineering and Technology, 7(6),
2016, pp.260277.
[21] S. Vimala and Dr. V. Khanna, Strongest Persistent Multicast Routing protocol for Reliable Transmission
in Both Ad-Hoc and Mobile Ad-Hoc Networks. International Journal of Civil Engineering and
Technology, 8(1), 2017, pp. 976986.
[22] Sarita R.Khot et al (2015) Repair of damaged RC beams externally Bonded with Glass Fiber Reinforced
Polymer sheets. IRJET Journal ISSN 2395-0056
[23] Shinde.D.N et al (2014) Flexural Behaviour of Reinforced Cement Concrete beam wrapped with GFRP
sheet, International Journal of Research in Engineering and Technology(IJRET) ISSN-2321-7308
[24] Shrikanth Harle (2014) Glass Fiber Reinforced Concrete and Its Properties, International Journal of
Engineering Sciences &Research Technology, ISSN 2277-9655.