Beruflich Dokumente
Kultur Dokumente
STANDARDS SEARCH
1.1 This test method covers the deep abrasive wear by measuring the loss of volume resulting from abrasion of unglazed
ceramic tile under given conditions by means of a rotating disc and the use of abrasive material. 1.2 The values stated in SI
units are to be regarded as standard. No other units of measurement are included in this standard. 1.3 This standard does not
purport to address all ... More
Active Standard(Latest Version) ASTM C648-04(2009) Standard Test Method for Breaking Strength of
Ceramic Tile
1.1 This test method covers the determination of the breaking strength of glazed ceramic wall tile, ceramic mosaic tile,
quarry tile, and paver tile, having a facial area of at least 1 in. 2 (6.4 cm 2 ). 1.2 The values stated in inch-pound units are to
be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for
information only and ... More
1.1 This test method describes the procedures and equipment required to test either glazed or unglazed ceramic tile for
resistance to repeated cycles of freezing and thawing. Ceramic tile of any size or shape may be tested by this test method.
1.2 The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are for
information only. 1.3 This ... More
ASTM C627-10 Standard Test Method for Evaluating Ceramic Floor Tile
Active Standard(Latest Version) Installation Systems Using the Robinson-Type Floor Tester
1.1 This test method covers the evaluation of ceramic floor tile installation systems, using the Robinson 2 -type floor tester.
1.2 This test method is intended solely for evaluating complete ceramic floor tile installation systems for failure under loads
and not for evaluating particular characteristics of ceramic tile, such as abrasion resistance. This test method does not claim
to provide ... More
Active Standard(Latest Version) ASTM C346-87(2009) Standard Test Method for 45-deg Specular Gloss of
Ceramic Materials
1.1 This test method covers the determination of the specular gloss of porcelain enameled specimens, but may be applicable
to other specimens having similar reflection characteristics. This test method may be used to compare the gloss of porcelain
enameled specimens or to provide an index of acid or abrasion resistance by measurement of gloss loss. Note 1 Specular
gloss is one of several ... More
1.1 This guide covers information to assist in the selection of a method for measuring the frictional properties of materials.
Requirements for minimum data and a format for presenting these data are suggested. The use of the suggested reporting
form will increase the long-term usefulness of the test results within a given laboratory and will facilitate the exchange of test
results between ... More
1.1 This standard establishes a classification of building elements and related sitework. Elements, as defined here, are major
components common to most buildings. Elements usually perform a given function, regardless of the design specification,
construction method, or materials used. The classification serves as a consistent reference for analysis, evaluation, and
monitoring during the ... More
ASTM E1331-09 Standard Test Method for Reflectance Factor and Color by
Active Standard(Latest Version)
Spectrophotometry Using Hemispherical Geometry
1.1 This test method describes the instrumental measurement of the reflection properties and color of object-color specimens
by the use of a spectrophotometer or spectrocolorimeter with a hemispherical optical measuring system, such as an
integrating sphere. 1.2 The test method is suitable for use with most object-color specimens. However, it should not be used
for retroreflective specimens or ... More
ASTM E2257-08 Standard Test Method for Room Fire Test of Wall and
Active Standard(Latest Version)
Ceiling Materials and Assemblies
1.1 This is a fire-test-response standard. 1.2 This test method is intended to evaluate, under specified fire-exposure
conditions, the contribution to room fire growth provided by wall or ceiling materials and assemblies, or both. The method is
not intended to evaluate the fire endurance of assemblies or fires originating in the wall assembly. The method provides a
means to evaluate the ... More
1.1 This guide describes methods for determining and evaluating causes of water leakage of exterior walls. For this purpose,
water penetration is considered leakage, and therefore problematic, if it exceeds the planned resistance or temporary
retention and drainage capacity of the wall, is causing or is likely to cause premature deterioration of a building or its contents,
or is adversely ... More
ASTM E662-12a Standard Test Method for Specific Optical Density of Smoke
Active Standard(Latest Version)
Generated by Solid Materials
1.1 This fire-test-response standard covers determination of the specific optical density of smoke generated by solid materials
and assemblies mounted in the vertical position in thicknesses up to and including 1 in. (25.4 mm). 1.2 Measurement is made
of the attenuation of a light beam by smoke (suspended solid or liquid particles) accumulating within a closed chamber due to
nonflaming ... More