Beruflich Dokumente
Kultur Dokumente
Operation manual
HCD-900 Accessories
1
MAIN MENU
Frequency Meter
FixedCode Duplicate
HoppingCode Duplicate
REMOCON Read Back Test
Code Checking Area
Make Hopping
Setting
Confirm
Fn
Cancel
1. Plug in the power adapter into power outlet and push power switch on.(Fig.1)
Caution: Do not put the duplicator on the metal surface while operating, and keep
interference away while operating.
2. LCD screen displays Main Menu.(Fig. 2)
MAIN MENU
Frequency Meter
Fig. 1 Fig.2
Remark: Press & to move highlight to desired mode and press Confirm . If you
would like to return to MAIN MENU after entering, press Cancel .
3. Function instruction
3-1. Frequency Meter (Fig. 3)
3-1-1. Func.: Read emitting frequency from remote controls.
3-1-2. Place original remote control on the Test Area of HCD900, and press any key
of remote control. The Measuring keeps flashing while reading the
frequency, and then shows the reading of frequency.(Fig. 4)
Fig. 3 Fig. 4
2
3-2. Fixed Code Duplicate: No.1 to No. 5 are for switch position 1, and No. 6 to No.10
are for switch position 2(dual frequency). (Fig. 5)
3-2-1. Func.: Read and duplicate fixed
FixedCode Duplicate
code from original remote control
1 2 3 4 5 6 7 8 9 10 into REMOCON remote control. It
10 key spaces remain provides 10 key spaces.(Fig. 5)
3-2-2. Places original transmitter on the
Ready Test Area of HCD900.
Fig. 5
3-2-3. Press and holding 1st button of
original remote control, LCD
FixedCode Duplicate
433.9 displays Processing. Releases
1 2 3 4 5 6 7 8 9 10 the button when beep. Now the
1 frequency of original remote is
shown above the number 1, and
9 key spaces remain the code of the 1st button of original
Ready remote has been read
successfully.(Fig. 6)
Fig. 6
3-2-4. Repeat step 3-2-3. until all keys of
FixedCode Duplicate original remote control have been
433.9 read by HCD900.(Fig. 7)
1 2 3 4 5 6 7 8 9 10 [Note: for dual frequency remotes:
1 1 1 1 RMC-552, RMC-556 & RMC-558 /
6 key spaces remain RMC-558C: No.1 to No. 5 is for the switch
position 1(Up) of REMOCON dual
Ready frequency remote, and No. 6 to No. 10 is
for the switch position 2(down).]
Fig. 7
3-2-5 (Only for dual frequency remote)
FixedCode Duplicate After all keys of 2 remotes with
433.9 different frequencies has been read
1 2 3 4 5 6 7 8 9 10 by HCD-900, press & to move
1 1 1 1 2 2 2 2 highlight to No.1 ~ No.5 and No.6 ~
No.10 to choose the right frequency
6 key spaces remain
channels on REMOCON remote by
Ready pressing & .(Fig.8)
Fig. 8
3-2-6. Press Confirm to enter duplicating
mode, the LCD displays as (Fig. 9)
3
FixedCode Duplicate
433.9
3-2-7. Connects B or C type REMOCON remote 1 2 3 4 5 6 7 8 9 10
control & HCD900 by using attached 1 1 1 1
cable. 6 key spaces remain
Fig. 9
Fig.10
3-3. Hopping Code Duplicate:(Fig. 11)
HoppingCode Duplicate
1 2 3 4 5 6 7 8 9 10
3-3-1. Func.: Read and duplicate hopping
10 key spaces remain code from original remote controls
into REMOCON remote controls.
Please enter 1st code
Fig. 11
Caution: Some brands of hopping code remote controls were required to input seed
code before going to next step. To input seed code, please follow the
steps below:
a. Touch Fn & simultaneously.
b. LCD displays Receiving seed code.(Fig. 12)
c. You can probably find the seed code button on the rear of original
remote control. It might be hidden in an eyelet. If so, you need a
acicular object to poke it for transmitting the seed code.
d. The LED displays (Fig. 13) when the seed code was received.
Fig. 12 Fig. 13
4
HoppingCode Duplicate 3-3-2. Place the original remote control
1 2 3 4 5 6 7 8 9 10 on the Test Area of HCD900.
3-3-3. Press and holding 1st button of
10 key spaces remain original remote control, LCD
Microchip HC5300
2 A72282F 24DC5718 displays a serial number(Fig. 14).
Please enter 2nd code Each remote control has its own
series number.
Fig. 14
Fig. 15
fig.16
3-3-6. Press and holding 2nd button of original
remote control, LCD displays as (Fig. 17) HoppingCode Duplicate
3-3-7. Repeat step 3-3-6. to store other keys 1 2 3 4 5 6 7 8 9 10
of original remote control.
1 1
8 key spaces remain
Fig. 17
3-3-8. Connect the H series REMOCON
remote control & HCD900 by using HoppingCode Duplicate
attached cable. 1 2 3 4 5 6 7 8 9 10
3-3-9. Press Confirm to program the 1 1
code into REMOCON remote control. 8 key spaces remain
3-3-9. LCD displays duplicating result as Programming success
Programming Success or Please enter 1st code
Programming Failure. (Fig. 18)
Fig. 18
5
3-4. REMOCON Read Back (For FixedCode)
3-4-1 Func.: To read the code from REMOCON remote control, and reduplicate the code
into other REMOCON remote controls.
3-4-2. Be sure to connect REMOCON
MAIN MENU remote control(existing code) to
Frequency Meter HCD900 by using attached cable
FixedCode Duplicate before entering REMOCON
HoppingCode Duplicate
REMOCON Read Back Read Back mode. (Fig. 19)
Code Checking
Remote Report
Fig. 19
Ready
Fig. 20
3-4-4. Replace the remote control by new REMOCON remote control and touch
Confirm . LCD displays duplication result as Programming Success or Programming
Failure.
Fig. 21
Fig. 22
6
3-5-4. Press 1st button of the duplicate,
Code Checking
HCD900 starts to check the
Please Enter 1st Code contrast, and then shows the
similarity percentage.(Fig. 23)
99.2
Percent Matched
Press cancel To Exit
3-5-6. To identify whether the remote control is fixed code or hopping code, press
1st button of the remote control. (Fig. 21)
3-5-7. The LCD appears Processing and goes to Fig. 22.
3-5-8. Press same button again. HCD900 starts to check the contrast, and then
shows the similarity percentage.(Fig. 23)
3-5-9. Hopping code remote control will result 0.0 percent matched.
Caution: The qualified duplication requires at least 90% similarity.
3-6 Make Hopping: Create a duplicate without the existing of original rolling code
remote control.
Make Hopping
3-6-1. Press and to choose the
brand what you would like to
clone. (Fig. 24)
FADIN 00
Fig. 24
3-6-2. Press to enter the Reference
Make Hopping Number Setting.
Press and to set up the
reference number. (Only need to
set up for certain brands) (Fig. 25)
FADIN 01
Fig. 25
Fig. 26
7
3-6-4. Press Confirm to ready to copy.
HoppingCode Duplicate Connect REMOCON rolling code
1 2 3 4 5 6 7 8 9 10 remote to HCD-900 by using
2 4 9 D D 6 B F D D attached cable. (Fig. 27)
0 key spaces remain
Fig. 27
3-6-5. Press Confirm to program the
HoppingCode Duplicate code into REMOCON remote
1 2 3 4 5 6 7 8 9 10 control. LCD displays duplication
2 4 9 D D 6 B F D D result as Programming Success or
0 key spaces remain Programming Failure.(Fig. 28)
Programming Success
Fig. 28
Notice: If the REMOCON remotes you prepare to copy the original remotes are
using 3V battery, please connect it to our HCD-900 by duplicating cable before you read
code from original remote to HCD-900.
Revised at AUG.,08,2015