ECG Hz Diere
ENGINEERING CONSILTANTS GROUP
CONTENTS:
SECTION 16785
\STER ANTENNA TELEVISION SYSTEM (MATV)
Rage,
PART GENERAL 3
11 Related Documents 2
12. Deseription of Work 2
13 Reference Codes and Standards 2
14 Submits 3
1S Quality Assurance 4
16 Delivery, Storge and Handling 4
17 Related Sections 4
Le As-Built Drawings 4
19° Spare Parts s
PART2 PRODUCTS
24 General s
22 Equipment and Materials 5
PARTS EXECUTION 8
31 Examination 1B
32 Insulation of Basic Identification B
33 Installation of Base Wiring System Materials 3
34 Installation of Television Distebution System 4
3.5 Field Quality Control IsECG AWD
ENGINEERING CONSULTANTS GROUP:
SECTION 16785
[MASTER ANTENNA TELEVISION SYSTEM (MATV)
PARTI GENERAL
11 RELATED DOCUMENTS
Drawings and_gencral provisions of the Contact, including General
Conditions, Conditions of Particular” Application of Divsion-1
Specification Sections, apply 1 work of this setion,
12 DESCRIPTION OF WoRK
This section covers the work of Main Television Distribution System a5
escrbed by the Contact documents (specifications, drawings, BOQ, ete)
Main Television (TV) distribution system shall receive, Jemodulate,
‘modulate and distribute the TV channels
Provide complete and filly funetional Main Television Distribuion System
‘using materials and equipment of types, sizes, tings and perormanee as
indicated.
‘Th Main Television Distribution System shall use three (3) reeivng dishes
to receive twenty (20) digital channels fee to air in ation to five (5)
Scrambled ones, System shall support future expansion up te 32 digital
channels
It shall also use UHF and VHF for receiving Teestrial channels
Received signals shll be processed, modulated and amplified by the Head
End Equipment.
“The internal network shall include amplifiers, coaxial low loss cables,
istibution cables, modulators, receivers, spite, tap off, connectors
os
‘The Contactor is required to submit power budget caleulaton; any required
amplifiers or accessories to assure standard signa level
‘TV serens re not prt of this section,
1.3. REEERENCE CODES AND STANDARDS:
Equipment and installations shal comply with the curent stipulations ofthe
Toca authorities in the Arab Republi of Eaypt and the standards of
Consultative Commitee International for Radio CCR.
oe nt Thin Sn UAT) Saga 4s
lita et 62) serasECG He MUD ols
= Hlectrnic Industries Association BIA
+ Intemational Organization of Standardization ISO
14 SUBMETTALS
‘Submit the following in accordance with Conditions of the Contract and
Division-1 Specification Setons:
+ General: Submit complete sets of documentation as stited by the
contract conditions indicating type, size, rating, syle, catalog number,
‘manufacturers names, photographs andlor eatalog datasets fo all items
to ensure compliance with Specifications. This documentation shall be
subjet to the approval ofthe Engineer and no equipment shal be ordered
‘without this approval for ll equipment and deviees which ae shown on
rings and in Bill of Quantiis,
= Shop Drawings: Provide shop drawings showing equipment and device
locations and connecting wiring of entire MAIN TELEVISION
DISTRIBUTION SYSTEM, including riser diagrams. Shop drawings
shall include, but not be limited t, the following
‘+ Complete one-line riser diagram() showing all equipment and size,
type and number of conductors, dB levels at cach junctioe box and ds
levels tthe end outlets,
‘+ Pinto pin conection digram,
‘+ Large sale drawing of the central television equipment
‘+ Provide calculations to suppor typeof cables, system gain and overall,
signal loss, in all cable routes from start end including network
accessories, in order to prove the adequacy ofthe proposed equipment
to provide signal stength at outlets
‘+ Include instructions and installation manuals.
‘+ Complete sequence of operations and funetons ofthe system.
‘+ Complete system block diagram,
+A ising of the manufacturers autorized local representative
‘responsible for istallation coordination and service,
= Product Data: Submit manufacturer's technical product da, including
specifications and installations for each type of equipment. Include
standard or typical riser and wiring diagrams, operation and maintenance
instructions for inclusion in maintenance manual.
Operation and Maintsnance Data: Submit operation and maintenance
data and pars liss for each type of equipment installed, including
fumished specialties and acessories, and circuit diagrams. Include this
data, product data, and shop drawings in operation and maintenance
‘manual; in accordance with requirements of Division-1 and ther relevant
documentation,
‘apts Sts 6) SnesECG 2K AUD ioe
15 |ALITY ASSURAN
15.1 Manufacturer Qualifications: Manufacturing fms of TV sytem shall be
regulatly engaged in manufacturing Televison Distribution Systems of type,
size and characteristics similar 10 those required by the Contact for this
projet and whose products have been in satisfactory service in similar
projects for not ess than five (5) years.
1.52 Installer Qualifications: Engage an experienced installer whois a fctory-
authorized sales and service represonstve to perform the work of this
fection, The installer firm shall have atleast five (5) years ef successful
installation experince of systems similar to that required fr this projet.
153 ‘Tenining: Equipments manufacturer and his authorized, local
‘epresentative shall provide, in depth, equipment service and programming
on site traning to selected Employers personne for one week,
16 DELIVERY, STORAGE AND HANDLING
Deliver products in Factory orignal, unopened containers. Store in clean, dry
and shaded space in orginal containers, Handle caefll avoid damage.
1.7 RELATED SECTIONS
‘The following setions include requirements which relate to this setion:
General Electrical Materials and Methods
Cable Trays
18 AS.BUILT DRAWINGS
Daring the construction ofthe system, the Contactor shal pot in writing ll
his remarks, during the progress of work, conceming any suggested
alterations ffom the shop drawings in wiring routes, locations of equipment
‘or devices which arise from coordination between the system and other
No execution of alteration is allowed before rceving writen approval
fiom the Engineer.
All alterations shall be registered and filled by the Contractors and extra
‘opics shall be submited to the involved parties Engineer, Project manage,
Site et)
[A complete as-built draft set of drawings and equipment schedules shall be
‘prepared 15 days after competion of work for approval ofthe Engines.
‘The draft as-built shall include all previously approved alterations. Final
‘originals and copies of orbit drawings should be submited ic accordance
with Division, Section 01330 "Submittals Procedures
estes ssn AL Ey ‘rorsDeliver Spare parts to Employer, befor installation begins, amish not less
than 5 perent ofthe quanfiy of each component of MAT installed onthe
project rounded to the next figure, package with protective covering for
‘Storage and identified with labels clearly deserbing conten
‘The Contractor shall guarantee the availabilty ofall the spare pats for a
petiod not les than five (5) year
PART2 PRODUCTS
2.1 GENERAL
Provide complete and filly factional Main Television Distibation System
using materials and equipment of types, sizes, ratings and performance as
indicated.
The Main Television Distribution System shal use three (3) reeiving dish
snd VHF and UHF antenna to receive digital channels and off. channcls
Received signals shall be processed, modulated and amplified by the Head
End equipment.
The intemal network stall include amplifies, coaxial low loss cables,
Aistbution cables, modulators, receivers, spliters, tap of, comectors, ee.
‘The contactor is requested 10 provide all the required equipment,
‘component, et which makes the system work as required without any extra
‘ost, the contactor is responsible for providing even those equipments
Which are not mentioned in specifications, BOQ and drawings.
22 EQUIPMENT AND MATERIALS
Use materials and equipment that comply with referenced stndards and
‘manufacturers standard design and constuction in. accoance with
published product information. Coordinate the features of materials and
‘equipment’ 30 they form an intograted. system with components and
inteconneetions matched fr optimum performance of specified functions.
Provide equipment using all solid-tte components fully rated. for
‘continoous duty at he ratings indicated or specified for normal operation on
input power supplied at 220 V, 50 Hz
A equipment and materials shall be designed to operate and provide
‘maximum continuous performance al temperature and humidity’ at the
Project location. Precautions shal be inherenly proved in equipment to
Droest them ffom reduction in performance or damage in oak climatic
‘conditions at peak continuous ouputECG UX ALM ioe
ENGINEERING CONSULTANTS GROUP EA
‘The system shall be basically a wide band master distribution stem whi
shall share common distribution equipment such as amplifirs ec
‘Output RF modulated channels shall be all combined and fed to wide band
Aistibation amplifier which provides suficient gain to the cable network.
All th channels shal be combined using appropriate combining module and
amplified to the required signal strength and then trnsmited to the
{istibation network cables.
‘The overall gain ofthe system starting ftom Head End equipment should
provide suitable signal level taking into consideration loss in cables and
Gain of amplifier should be selected in complete coordination with the
overall oss figures ofthe composite network
‘The Head End equipment shall include signal processors. It is preferred to
Ihave a signal processor in every modulating and eceving modu.
‘The Output signal siength atthe most remote locations
cof 65-80 dBv and SIN btter than 60 dB,
It bein the ange
be located within 70 dB to achieve
‘The Main Television Distribution System shall consist but snot limited fo:
Wall mounted rack
‘Thre satellite dish antennas 1.8 m
= VHF Antenna
= UH Antenna
~ RF Headend equipment
= DvD player
~ Trunk amplifier
~ Distribution ample
~ Spliters & tap off
~ Low loss coaxial cables
= Distribution coaxial cables
~ RF and TF outlets
~ Connectors
~ Distribution boxes
tet ein Sp ATO tn
Mate et 6) TeesECGY2 Were
~All necessary acessories.
221 Receving Dishes: Every dish shall have LNB to recive the broadcasted
. ‘TV channels, The dishes sall be coming with fixing base, INBS and all
shar equired acess.
: “The dishes shal be bl to eeive the digi TV chanel The dishes shal
te18mdaneter
‘The dishes and its fixation shal be strong enoughf face the wind oad. The
sain ofthe dinis shouldbe adequate achieve clear recepion
‘The dish mounting sll be galvanized sts! manufactured. The dish sal
be perfecting parabolic andthe rim shall ad more strength to ‘he elector.
Ths ish sll be one piece sphere made of non-comenive meal o solid
A, lumina, which concentrates the signals ceived rom the satlite toward
4 receiving bead Toston atthe focal point of ih, that mean high cae
noise aio (CN).
i LNB: The provided LNB shal lave four outputs Horizontal and Vertical
(Hi, & Lo), The LNB shall have the following specifications:
r = Nowofoupus: 4 ouputs (Quad outputs)
~ Sat input requeney: 9.751275 GHZ
f = Oupue Frequency: 9502150 MHZ
~ Gain: Mia $508
r ~ Noise Factor: Max 15.48
~ Swithing Technique Vi 14/18 VDC, WLo 0722 KHZ
i 222 VHP and UHE Antenna
a OFF-Air, Mast Mounted Antennas: Weutherproof single-channel or
‘woadband ype, constucted of high-stengh anodized aluminan and rated
to survive ina 160-avh wind, minimum. Directo, with dsb det
. amy and ant-ghost reflector system, offering a gun of 13 43 or higher.
Doda antennas foreach of band VHF, and UHF programs shall be
povided. Provide adequate number o cove al Iocl chanel, without the
. ‘ood to roa antennas, Provide weather sale conection fr the cou
Ting to antennas
. ~ ElomsatItemaly dampened guns such mechanical vibtin 2s may
~ Ends ofross.anmsandslemeats sealed
~ Mounting and connsting hana orsion proof
~ Frequency ange: matched to source fequencis
S Sepia ete) sor223
ECGXti Abo Wire
RE Hes
nd Equipment
Provide fctory-assemble, solid-state sealed type wide band multi channels
Head end equipment as described
‘The Head End equipment shall receive the TV channels (IF) from the
receiving dish in digital form. Tho head end equipment stall roccive,
‘demodulate, modulate the selected received channels to the required
andard TV channels, combine the channels and amplify them to be
transmitted through the network
‘The Head End equipment shall include receivers, modulators, preamplifiers,
processors, Terrestrial channel converters, active and passive equipment,
Combiners, wideband amplifiers, active and passive accessories, et,
‘Tho Headend shall include receivers with common interface anit (CD in
order o receive encrypted channels
‘The Head End Equipment shall include, but is no limited to, ke following
pars
— Incoming signal processor forthe digital video channels
~ Base units with power supply, control module, Headend amplifier, RF
spliters, combiner and all necessary acessories
~ Free to Air digital rovers and modulators.
~ Audio video modulators
~ Digital receivers with common interface (C1) and modulators.
= Temetrial channel converters
~ Broadband IF splitters, connectors and all necessary acessories.
~ The audio output of ll the modules shal be stereo.
~ Master combiner
= Main wide band high gain amplifier
~ Monitoring and control equipment (TV serens, PC, et.)
~ Racks
Headend Base Uni
‘The following are the minimum performance specifications
‘Frequency Range 47-862 Me
Output Level 100 dB min adjustable
Noise Figure: 44D, ae fal xin
InpuOutput Impedance: 7S ohms
tae ts en Se AT ton
Medinet moet menteECG ALD ols
Retum Loss 14aB mi.
LNB Supply [3-18 VDC (remote fied voltage)
Powsr Supply 220 VAC, $0 He, reguated power
‘Adjacent channel operation
igh SN Ratio
Test Output
“The Headend could be consists of more than one Base unit,
‘The Headend shall be moduler:
Digital Receiver with or without Common Interface(OPSK/AV)
‘The digital rociver shall convert the QPSK signal to AutioVVieo signal
‘The following are the minimum performance specifications
Frequeney Range 1950-2150 Mz
Input Level 45-70 BV
‘Sombol Rate: 232Mals
‘Protection Interval 1/2, 28, 314, 516,78, 89 (Auto)
Audio Level Adjustable
Video Level: 1 Vss—75 Ohm
Modalators
‘The following are the minimum performance specifications:
‘Video input Level 1 Vss—75 Ohm
‘Output Frequency 47-862 Mi
Audio Input Adjustable
Output eve: 90 dBUV min
‘Video Standard: PALISECAM/ NTSC
Tsun BIG, DIK, M,N
The modulator audio system shall be sero.
Combined digital receiver and modulator can be acepte.
itn e162 asECG AWD coe
‘Terrestrial Channel Converters
‘The Terestral channel converters shall he used forthe conversion of one
nalogdigital TV channel into the range of 45-862 MHz
‘The following ae the minimum performance specifiations
” sang 87-108 MH
Input Level Rang: 50.90 dBuV
Joel 85 dBAV min
Video Stand PALSECAM/ NTSC
‘TV Standard: BIG, DIK, M,N
224 DVD Player:
DVD shall be used to play both types of CDs (audio CDs aad all video
cps.
igh picture quai.
Play dise types (DVD, video, DVD-R, video CD, audio CD, CE, CDR-CD.-
RW)
‘Outpt signal: Dolby, DTS over optical and coaxial interface.
Fast picture start
24 bit Audio DAC for high sound quality
lO bit video D/A.
2.25 Distribution Amplifier:
The distribution amplifier shall be used in each floor. The contactor should
provide the appropriate gain taking into consideration the VHF & URE
‘ipment gain and the actual lose of cables and acessories in order to
provide the specified signal swength which must be located within 70 &B,
“The amplifiers shall support forward and tun signals fr inersive
system.
Provide fctory-assmbled, solid-state wide band amplifier, with AGC, for
UHF & VHF channels/requences as indicated. Equipment amplifiers with
chassis connectors which match and mate with coaxial cable connectors
fers with following minimum electrical performance
120 dB min, (ull AGC), adjustable
a8
igure: 748, fll gainECGY2WbDierr
r dao: 69 40,V min. 1085 ABV ax
Return os input an output 15 min,
7 ‘Ouput vl con ‘51066 dBi adjustment ane)
AGC rage: oan
. Band nas fans: +1 tat 10 Mil bandwidth
Retu os in: 1248 retu on (VSWR 1.671)
x Input mash channels 21 through 69: Not ss han 6 4B mi.
‘Retur oss output 10 48 ret os
ower sul 220 VAC, 50 Ha, eglted power
22.6 ‘Tap-offs and Splitters:
f The tapos and splits must be selected caeily to frm an equalized
network. All aot and plies shall be F comector Ope and sal
. Spor forward and cum signs or interactive syst
soliters
r = Frequency range 4-862 MIIZ
+ igh et oss 2208
= Compact silver plated dic — cst housing
= Feomeetrs
r Teas
~ requeney range 4-862 MHZ
i = High eto sotaion
= Compact sive pated de —cast ousng
eonnetos
22:7 Lowes Consal Cable:
Stall be used fr risers and for distibution boxes interconnections. Cable
stall consist of «center conducor na soli ilecre completly enclosed
P by a metalic covering, which sal be flexible coper braid nslting
jactey usualy ving paste sal be molded over the entre ine ax
‘roletivecuhide coating Te Tine relatively inmune wo stay pickup
r ‘ecase te outer conductor acs sa grounded sel. The coal ie shall,
‘bo unbalanced with the nner conductor supplying antenna signal and the
‘uer conductor conesed to rzeiver canis. The coaxial ie general,
r Shall aves characteris impedance of 7S ohmsECGXti Aiwa
ENGINEERING CONSULTANTS cROUP 4
“The cable shall have characteristics better than (RG 11) and shal have max
9.5 dB lss/100 m at 950 MHz
2.28 Distribution Coaxial
able:
Cable shall consist of a center conductor in a solid dielectric completly
enclosed by a metalic covering, which shall be flexible coppe: braid. An
insulating jcket, usually vinlite plastic, shall be molded over the etre line
35 a protective outside coating. The line is relatively immune to stay
Pickup because tho outer conductor ats asa groundad shiold, The coaxial
Tine shal be unbalanced with the inner conductor supplying anenna signal
tnd the outer conductor connected to receiver chassis. The soaxil ine
generally, shall have a characteristic impedance of 75 obs.
‘The cable shall have characteristics better than (RG-6/U) and shall have max
163 dB lose/100 m9 950 Mik
229 Drop Coaxial Cable:
‘Shall be used mainly forthe outlets connections (drop cables).
CCable shall consist of a centr conductor in a slid dielectric completely
enclosed by a metalic covering, which shall be flexible copper braid. An
insulating jacket, usually vinylt plastic, shall be molded over the enti ine
45 a protective outside coating. The lin is relatively immne to stray
Pickup because the outer conductor acts asa grounded shield. The coaxial
line shall be unbalanced withthe inner conductor supplying amenna signal
land the outer conductor connecod to rocsver chassis. The coaxial line,
‘generally, shall havea characteristic impedance of 75 ohins
The cable shall have max. 19 dB los!100 m at 950 MHz
2210 RETV Outlets
Shall be end type and shall have frequency ange 0-900 Milz and max. dB
lose dB at 860 MIL
22.11 Connectors:
Shall be F type with sizes suit the cables (pes (low loss cables and
istribuion cables).
= Impedance Matching: To obtain maximum efficiency ant eliminate
reflections inthe anlenna sytem that nay produce ghosts or reduce the
detail i picture, the impedance of the antenna, tansmission line end
receiver, input circuit shall be matched. Matching corditions i.
‘mavimnim transfer of power and sigal stength and minimum reflected
signal shall be measured2212
PARTS
uM
32
33
ECG CAMWD ioe
ENGINEERING GONSIATANTS GROUP.
= Grounding: To prevent accumulation of static charge on antenna
supporting structure, it shll be grounded by connecting a beavy ground
‘wie to dhe system earth (metal stake driven into the eat). Grounding of
the mas i also essential
= Accessories: The cable networks shall include all necessary acessories.
Alt accessories shall operate atthe system frequency range which covers
‘the roquired band of frequencies.
‘Accessories shall have the minimum gain Toss and stall provide
“sufficient isolation on return loss characteristics,
Protection
‘Thre types of protection shal be required It earthing for anennas, racks
and equipment; 2nd: lighining protection for antennas, 31d lightning
protection for signal ables.
XECUTION
EXAMINATION
[Examine reas and conditions under which Television Distribution System
shall be installed. Do not proceed with work until unsatisfactory conditions
have been corrected in-a manner acceptable to the Engineer
INSTALLATION OF BASIC IDENTIFICATION
Install electrical identification in accordance with requirements of Scion
16050 "Basie Eletiel Materials and Methods”
INSTALLATION OF BASIC WIRING SYSTEM MATERIALS
Install wiring, raceways or conduits eletial boxes, eables and fitings in
sccordance with Section 16050 "Basic Electrical Materials and Methods”
lauses: "Racoways", "Wires and Cables" and "Electrical Boxes and
Fittings for wiring ofthe ton-power limited circuits and Secticns related to
*Cable Networks
Install witing of signal circuits and power limited circuit in raceways oF
conduit of exposed on wall or esilings when properly proteted. Use
Conduits for runs though floors or in shalt ways to height of2.3 m abowe
floor. Provide cables in plenum spaces in metalic raceways or with cables
jackets approved for use in plenum spaces
Install cables using special stripping tools which do not harm shiclds and
insulators. Use special ripping tools and donot use solder type fitings and
PeelersECGXtAUWere
34 INSTALLATION OF TELEVISION DISTRIBUTION SYSTEM
Installation of equipment and doves that pertain to other work of the
Contract stall be closely coordinated with the appropriate trade,
Equipment manufacturer shall provide all necessary sssisince 10 his
authorized, local representative to;
= Coordinate the selection of sytem equipment
~ Execute fel strength tests for all frequency bands to be recived by the
systom (VHF, UHF, KU, et).
= Supervise the instalation of complete Television Distribution System,
= eform complete functional tess of the system at all oes neling
signal sength, reflection coefficient, ec
~ Submit a writen report attesting the proper operation ofthe completed
system.
Install Television Distribution System as indicated on Drawings in
sccordance with equipment manufacturers writen instructions and comply
‘with the standards oF installation,
Complete wiring in accordance with manuficture?’s requirements. Colour
code wiring and install per manufacturers point-to-point wiring disgram
Determine exact numberof wires for each device installed. Connect each
device with suficient wiring 0 complete it intended operation.
Where there are a number of power requiring devices, provide exta or
larger size wiring to allevite voltage drops which makes device operate
‘beyond voltage limits for which it was designed. Determine above with
‘manufacturers represetaive while equipment i being installed
‘Submit signed copy of test results in duplicate to the Engines.
Equipment cabinets shall be installed ina special room for the Television
Distribution System and shall be arranged to permit easy servicing ofthe
ferent pars.
(Cable bearers shall be installed on walls wherever neoded
Wall mounted equipment shall be installed according to the manufieruree
recommendations
Powersupply distribution board shall be installed in an arrangement which
oes not affect the salty of equipment and cause no interfererce with the
{elecommunication system,
‘ptt tm a6) ae aSas
351
36
ECG Hc AM Deere
Air-conditioning shall be provide to the room ifthe Television Distribution
System stable operating conditions and design considerations, stated bythe
rmanufictarer, require,
Fresh si supply to the room shall be highly filtered to prevent the dust from
catering equipment
Powerful and even distributed illumination forthe room ofthe switching
‘guipment shall be provided to permit easy view ofall components
‘Equipment room shall be fited with dustproot doors and windows
Ambient conditions hal be considered in the design of his room.
FIELD QUALITY CONTROL
‘Connection and Supervision: Make connections to equipmen! panel under
‘manufacturer's supervision. Complete connections between cabinets and
panels utilizing Manufacture’ technieians
‘Sestem Test and_Approval: Submit shop drawings for funtion and
‘operation only, pre-approved by the Engineer.
Prior to final acceptance of the system, the manufacturer of sytem shall in
prcsence of the Contactor, Employer's representative anc Engincor’s
reprosentatve test each extension device,
WARRANTY
‘The Contractor shall guarantce the equipment and workmanship fortwo (2)
years after the final handing over ofthe system,
END OF SECTION 16785
meas