Beruflich Dokumente
Kultur Dokumente
Technical Services: Tel: (800) 381-9312 / Fax: (800) 791-5500 Tel: (215) 362-0700 / (800) 523-6512
Fax: (215) 362-5385
1/2" NPT
2-11/16" FACTORY
(68,3 mm) ASSEMBLED
UPRIGHT 7/16"
7/16" SHIELD MODEL S5 (11,1 mm)
(11,1 mm)
PENDENT NOMINAL
NOMINAL
WRENCH SHIELD MAKE-IN
MAKE-IN
FLANGES WITH 2-5/8"
O-RINGS (66,7 mm)
WRENCH
AREA
UPRIGHT PENDENT
(FACTORY ASSEMBLED) (FIELD ASSEMBLED - SEE INSTALLATION SECTION)
FIGURE 1
STANDARD RESPONSE SERIES TY-L UPRIGHT (TY3113) AND PENDENT (TY3211) SPRINKLERS
INTERMEDIATE LEVEL SPRINKLERS, 5.6 K-FACTOR, 1/2 INCH NPT
3/4" NPT
2-3/4" FACTORY
(69,9 mm) ASSEMBLED
UPRIGHT 1/2"
1/2" (12,7 mm)
SHIELD MODEL S5
(12,7 mm) NOMINAL
NOMINAL PENDENT
SHIELD MAKE-IN
MAKE-IN WRENCH
FLANGES WITH 2-11/16"
O-RINGS (68,3 mm)
WRENCH
AREA
UPRIGHT PENDENT
(FACTORY ASSEMBLED) (FIELD ASSEMBLED - SEE INSTALLATION SECTION)
SPRINKLER FINISH
K = 5.6, UPRIGHT TY3113 K = 8.0, UPRIGHT TY4113
K = 5.6, PENDENT TY3211 K = 8.0, PENDENT TY4211
NOTES:
1. Listed by Underwriters Laboratories, Inc. (UL).
2. Listed by Underwriters Laboratories, Inc. for use in Canada (C-UL).
3. Approved by Factory Mutual Research Corporation (FM).
TABLE A
LABORATORY LISTINGS AND APPROVALS
Physical Characteristics
Frame . . . . . . . . . . . . . . Brass Design
Sealing Button . . Bronze w/Teflon
Ejection Spring . . . . Stainless Steel Criteria WRENCH
Fusible Element . . . Solder, Copper RECESS
. . . . . . . . . . . . Stainless Steel The Series TY-L Pendent and Upright
Strut . . . . . . . . . . . . . . Monel Intermediate Level Sprinklers are in-
Hook . . . . . . . . . Bronze/Monel tended for fire protection systems de-
Deflector . . . . . . . . . . . Bronze signed in accordance with the stand-
Shield . . . . . . . . . . . . . . Brass ard installation rules recognized by the
DuPont Registered Trademark applicable Listing or Approval agency
(e.g., UL Listing is based on the re-
quirements of NFPA 13, and FM Ap-
proval is based on the requirements of FIGURE 3
Operation FMs Loss Prevention Data Sheets). W-TYPE 9 SPRINKLER
WRENCH
A copper tube sealed by two stainless
steel balls holds a fusible alloy. When Installation
the rated temperature is reached, the plied to the pipe threads, hand tighten
alloy melts, the balls are forced toward The Series TL-B Sprinklers must be the sprinkler into the sprinkler fitting.
each other releasing the tension installed in accordance with the follow-
mechanism, allowing the sprinkler to ing instructions: Step 2. Tighten the sprinkler into the
operate. sprinkler fitting using only the W-Type
NOTE 9 Sprinkler Wrench (Ref. Figure 3).
A leak tight 1/2 inch NPT sprinkler joint With reference to Figure 1 or 2, the
should be obtained with a torque of 7 W-Type 9 Sprinkler Wrench is to be
to 14 ft.lbs. (9,5 to 19,0 Nm). A maxi- applied to the wrenching area.
mum of 21 ft. lbs. (28,5 Nm) of torque
may be used to install sprinklers with Pendent Sprinklers
1/2 NPT connections. A leak tight 3/4 The Series TY-L Intermediate Level
inch NPT sprinkler joint should be ob- Pendent Sprinklers must be installed
tained with a torque of 10 to 20 ft.lbs. in accordance with the following in-
(13,4 to 26,8 Nm). A maximum of 30 structions.
ft.lbs. (40,7 Nm) of torque is to be used Step 1. Roll one of the two required
to install sprinklers with 3/4 NPT con- O-Rings over the sprinkler threads un-
nections. Higher levels of torque may til it seats against the sprinkler wrench-
distort the sprinkler inlet and cause ing area flange as shown in Figure 1 or
leakage or impairment of the sprinkler. 2, as applicable.
Upright Sprinklers Step 2. Install the Shield over the
The Series TY-L Intermediate Level sprinkler threads, and then roll the sec-
Upright Sprinklers must be installed in ond O-Ring over the sprinkler threads
accordance with the following instruc- until it is seated firmly against the
tions. Shield.
Step 1. With pipe thread sealant ap- Step 3. With pipe thread sealant ap-
Page 4 of 6 TFP350
TABLE B
PART NUMBER SELECTION
SERIES TY-L UPRIGHT INTERMEDIATE LEVEL SPRINKLERS
(UPRIGHT SHIELD INCLUDED WITH SPRINKLER)
TABLE C
PART NUMBER SELECTION
SERIES TY-L PENDENT SPRINKLERS
(MODEL S2 PENDENT SHIELD & O-RING MUST BE SEPARATELY ORDERED)
Sprinkler Wrench:
Specify: W-Type 9 Sprinkler Wrench,
P/N 56-000-1-849.
Page 6 of 6 TFP350
TYCO FIRE PRODUCTS, 451 North Cannon Avenue, Lansdale, Pennsylvania 19446