Beruflich Dokumente
Kultur Dokumente
THE ADVANTAGES
Product Interface:
* Front panel display screen with keypad
* Local access by PC with internet explorer software (non-dedicated software)
* Remote access via PC modem (Internet explorer)
*future capabillity
Barber-Colman
Barber-Colman DYNA Products
P.O. Box 2940 Tel: (815) 637-3000
1354 Clifford Avenue Fax:(815) 877-0150
Loves Park, IL 61132 www.dynaproducts.com
USA
DYNA 314
FUNCTIONS INPUTS/OUTPUTS
Automatic or manual engine control. Genset three phase voltages (3 or 4 wires).
All engine parameters display. Genset three phase currents.
All genset electrical parameters display. 15 logic inputs with programmable sequences.
All utility/mains electrical parameters display. 7 logic outputs with programmable sequences.
Manual and automatic synchronization 1 magnetic pick up speed input for isochonous
(synchronizing scope available on screen). regulation.
Isochronous active load sharing control. 1 output (analog or PWM) for speed control
Iso-voltage reactive load sharing control. compatible with all electronic regulations
Power factor control when paralleling with utility. (Barber Colman, woodward, GAC, Heinzmann,
Automatic start/stop genset control according Ambac, DDEC, MDEC,).
with load. 1 analog output for voltage control compatible
Power level control (constant power or peak with most AVR (Leroy Sommer, Stanford,
shaving) when paralleling with utility. Basler,).
Temperature regulation for cogeneration.
Data circular records.* SERIAL PORTS
Events records/data logging.*
Maintenance cycle control. 1 RS232 port for PC communication + modem.
Hour run meter. 1 RS485 port with protocol Modbus RTU.
Active and reactive energy counters. 1 Bus Can port for inter Gensys communication.
Web email message on alarm detection (option). 1 Bus Can port for opencommunication with
Real time clock other modules.
Genset electrical protections:
over/under voltage
over/under frequency
over current
over neutral current
over power
over reverse power
over reactive power
over reverse reactive power
Utility/Mains electrical protection:
over/under voltage
over/under frequency
vector jump
df/dt or rate of change of frequency
WARNING
Barber-Colman requires an independent overspeed shut
down device to prevent loss of engine control which may
cause personal injury and/or equipment damage.
- NOTE -
Barber-Colman believes that all information provided herein is
correct and reliable and reserves the right to update at any time.
Barber-Colman does not assume any responsibility for its use unless
otherwise expressly undertaken.
*future capabillity
analog
Speed out+
-
power supply -
K3
Speed
Speed ref
regulator
Shield
F
OR
+ Actuator +
Actuator -
F
G9 G11 G10 K4 K5
Emergency
A3
stop
Analog
+
G
AVR out +
Crank
AVR
CRANK -
A1
+Alim
Fuel
A2
Gen L2
L2
Gen L3
L3
Gen N
N
B2 B3 B4 B1
SPARE Output 1
C1
S1
P1
Gen 3-
D1
- Lubrification pmp
P2 S1
P1
- ... SPARE
C3
Gen I2-
D3
S2
Output 4
SPARE
C4
P2 S1
P1
Gen I1+
D6
Output 5
C5
+Alim
S2
P2
Shield
F5
Gen common
E6
- Alim
Gen Breaker NO
E5
Oil Pressure
Oil pressure meas. +
F9
E4
Gen Breaker NC
Water temp meas. -
F6
Water temp
Water temp meas +
F7
Load
Engine meas. 1 -
F1
Engine meas. +
F2
Mains Breaker NO
E2
Engine meas. 2 -
F3
Spare 2
Mains Breaker NC
E1
Engine meas. 2 +
F4
- Alim
100 - 480 V
F
Mains L3
L3
Mains L1
B6 B5
S1
L1 P1
Shield Mains I1 +
D8
0-20mA -
G2 G3
Mains power or spare Mains I1 -
D7
0-20mA +
G1
Shield
Parallel +
Mains
G5 G6
Parallel lines to GCR or BC
analog load sharing Mains breaker IN
J1
Parallel -
G4
Gen Breaker IN
J2
6 - Tx
9 - 0V
5 - Rx
4 - 0V
3 - 0V
8 - NC
7 - NC
2 - NC
1 - NC
- Charger fault
RS 485
Water temp
J5
DB9 male
- Air damper shut
- Exter electrical fault
Input 1
J6
- ...
Infos / Alarms
/ realtime display
Configuration / tele-maintenance
(MDEC,...)
Input 2
J7
CAN1 to
6 - 0V
5 - 0V
3 - 0V
9 - NC
8 - NC
4 - NC
1 - NC
CAN 1
DB9 male
7 - CANH
Input 3
J8
Input 4
J9
/ realtime display
Configuration / maintenance
CAN 2 to options Input 5
...
6 - 0V
5 - 0V
3 - 0V
9 - NC
8 - NC
4 - NC
1 - NC
CAN 2
DB9 male
2 - CANL
7 - CANH
Input 6
J10 J11
Modem
Modem
Input 7
J12
RS232 to PC or modem Input 8
J13
9 - RI
2 - Tx
5 - 0V
3 - Rx
1 - NC
RS 232
8 - CTS
7 - RTS
6 - DTR
4 - DSR
DB9 female
Input 9
J14
- Alim
Input 10
J15