Beruflich Dokumente
Kultur Dokumente
Building Plot / Grid Max. Actual Heaviest Lift: Max. Radius: Determining Lift: Boom length at;
Ref: & Floor Level Crane Details Outrigger / predicted
Centres outrigger load ( Heaviest Component Heaviest Lift ( Component Weight Max. Radius ( Component Weight Determining Lift Heaviest lift::
(length x e.g. LICCON Weight + Tackle & Block) SWL + Tackle & Block ) SWL + Tackle & Block ) SWL Max. Radius:
width) ( A) / Radius / Radius / Radius Determining Lift :
Crane Required To Undertake Lift ( 3.25 + 0.75 ) ( 2.9 + 0.75 ) ( 2.9 + 0.75 ) HL: 41.6 m
Example 80 Tonne AT Liebherr 8188 x 7000 35 Tonne 4.00 Tonnes 7.2 Tonnes 3.65 Tonnes 4.3 Tonnes 3.65 Tonnes 4.3 Tonnes MR: 41.6 m
Building LTM 1080/1 (Std 16 t c/w) mm @ 20 m @ 20 m @ 28 m @ 28 m @ 28 m @ 28 m DL: 41.6 m
Max. Alternative Crane Permitted
[ 2nd Floor ] N/A N/A N/A Permissible Bearing Capacity Provided by Client: 22 Tonnes / m2
N/A
Single Day Lift Clients Site Representative Signature Prior To Commencing Lift: Safety Factor included in above: Yes 2.0 Therefore no additional safety factor required
Operation from
The crane is rigged in the anticipated crane stand position as indicated on the Lift Plan. Actual / predicted outrigger jack load ( A ) (worst case including alternative crane if applicable): 35 Tonne
Crane Stand A The crane hardstanding has been prepared adequately to withstand 22 Tonnes / m2
Full consideration has been given to all factors, including; Potential ground deterioration Consider area of Standard Crane Mats ( B ) = 900 mm diameter = 0.64 m2
Date Of Lift:: due to weather / construction activity since initial investigation / assessment;
Pressure applied beneath Standard size mats = ( A B ) = 54.7 Tonnes / m2
*****/*****/****** Print Name: Signature: Date:
54.7 Tonnes / m2 is greater than 25.0 Tonnes / m2 Therefore mats are of inadequate size
11.6 Tonnes / m2 is less than 22.0 Tonnes / m2 Therefore mats are adequate
Crane Required To Undertake Lift HL:
********** MR:
********** DL:
Max. Alternative Crane Permitted Permissible Bearing Capacity Provided by Client: XXX Tonnes / m2
********** / N/A Safety Factor included in above: Yes XX Any additional safety factor required?
Clients Site Representative Signature Prior To Commencing Lift:
Actual / predicted outrigger jack load ( A ) (worst case including alternative crane if applicable): 35 Tonne
The crane is rigged in the anticipated crane stand position as indicated on the Lift Plan.
The crane hardstanding has been prepared adequately to withstand ***** Tonnes / m2 Consider area of Standard Crane Mats ( B ) = XXX mm diameter = XXX m2
Full consideration has been given to all factors, including; Potential ground deterioration
Date Of Lift:: due to weather / construction activity since initial investigation / assessment; Pressure applied beneath Standard size mats = ( A B ) = XXXX Tonnes / m2
*****/*****/****** Print Name: Signature: Date: XXX Tonnes / m2 is greater than / less than XXX Tonnes / m2 Therefore mats are of inadequate / adequate size
XXX Tonnes / m2 is greater than / less than XXX Tonnes / m2 Therefore mats are of inadequate / adequate size