Beruflich Dokumente
Kultur Dokumente
EXL9330
LEXAN EXL9330 is a nonbrominated, nonchlorinated PC/siloxane
copolymer. ECO conforming. Excellent low temperature
impact.
100 100
60
50
20
20 40 60 80 100
Gate Pressure (MPa)
PHYSICAL
Mould Shrinkage on Tensile Bar, flow 2) 0.5-0.7 % ASTM D955
RHEOLOGICAL
Density 1.19 g/cm ISO 1183
Melt Volume Rate, MVR 300 C / 1.2 kg 9 cm/10min. ISO 1133
EXL9330
TYPICAL PROPERTIES1) TYPICAL VALUE UNIT STANDARD
MECHANICAL
Tensile Stress at yield, 50 mm/min 55 MPa ISO 527
Tensile Stress at break, 50 mm/min 60 MPa ISO 527
Tensile Strain at yield, 50 mm/min 6.0 % ISO 527
Tensile Strain at break, 50 mm/min 125 % ISO 527
Tensile Modulus, 1 mm/min 2100 MPa ISO 527
Flexural Strength at yield, 2 mm/min 85 MPa ISO 178
Flexural Modulus, 2 mm/min 2200 MPa ISO 178
Hardness, H358/30 90 MPa ISO 2039/1
IMPACT
Izod Impact, notched 80*10*4 +23 C 65 kJ/m2 ISO 180/1A
Izod Impact, notched 80*10*4 - 30 C 58 kJ/m2 ISO 180/1A
Izod Impact, notched 63.5*12.7*3.2 +23 C 80 kJ/m2 ISO 180/4A
Izod Impact, notched 63.5*12.7*3.2 -30 C 65 kJ/m2 ISO 180/4A
Charpy V-notch edgew. 80*10*4 s=62 mm, +23 C 75 kJ/m2 ISO 179/1eA
Charpy V-notch edgew. 80*10*4 s=62 mm, -30 C 60 kJ/m2 ISO 179/1eA
THERMAL
Coeff. of Lin. Therm. Exp. flow 23 80 C 7.2 E-05 1/C ISO 11359-2
Coeff. of Lin. Therm. Exp. xflow 23 80 C 7.7 E-05 1/C ISO 11359-2
Ball Pressure Test, 125 C 2 C PASS - IEC 60695-10-2
Vicat B/50 140 C ISO 306
Vicat B/120 142 C ISO 306
HDT/Be, 0.45 MPa edgew. 120*10*4/s=100 mm 135 C ISO 75/Be
HDT/Ae, 1.8 MPa edgew. 120*10*4/s=100 mm 124 C ISO 75/Ae
Thermal Index, Electrical properties 125 C UL 746B
Thermal Index, Mech. prop. with impact 115 C UL 746B
Thermal Index, Mech. prop. w/o impact 120 C UL 746B
FLAMMABILITY
94V-0 Flame Class Rating 3) 1.50 mm UL 94
94-5VA Flame Class Rating 3) 3.00 mm UL 94
Glow Wire Flammability Temp 960 C, passes at 1.0 mm IEC 60695-2-12
Oxygen Index 3) 35 % ISO 4589
ELECTRICAL
Volume Resistivity >1E15 Ohm-cm IEC 60093
Surface Resistivity, ROA >1E15 Ohm IEC 60093
Dielectric Strength, in oil, 3.2 mm 16.0 kV/mm IEC 60243-1
Relative Permittivity, 50 Hz 2.6 - IEC 60250
Relative Permittivity, 1 MHz 2.7 - IEC 60250
Dissipation Factor, 50 Hz 0.0010 - IEC 60250
Dissipation Factor, 1 MHz 0.0085 - IEC 60250
Comparative Tracking Index 225 V IEC 60112/3rd
1) Typical values only. Variations within normal tolerances are 2) Only typical data for material selection purposes. Not to be
possible for various colours. All values are measured at least used for part or tool design.
after 48 hours storage at 23C/50% relative humidity. 3) This rating is not intended to reflect hazards presented
All properties, except the melt volume rate, are measured on by this or any other material under actual fire conditions.
injection moulded samples. 4) Own measurement according to UL.
All samples are prepared according ISO 294.