Beruflich Dokumente
Kultur Dokumente
PWR_BTN#
4a
4b AUXPWROK
6 13
5VS AUXOK
AUXOK H_PWRGD
3VS SOUTH PWRGD#
SUSB# NOUTH
1.8VS 5 12
1.2VS CIRCUIT BRIDGE BRIDGE
SUSB# PCIRST# CPU
1.5VS SWITCH SIS 672
SIS 968
1.05VS PWROK RESET#
PWROK
0.9VS H_CPURST#
SB_PWROK
1.8V_PWRGD
8 VCORE 11 14
1.5V_PWRGD
7 IMVP-EN U19
1.05VS_PWRGD
IMVP-6
VCORE_ON DELAY_PWRGD
PU4
10
9 CLKEN#
CLOCK GENERATOR
ICS9LPR310BGLF
Power Sequence Signal Compare List
Item Signal Location Value Item Signal Location Value
1 VIN PQ46_5,6,7,8 0.5288V 16 5VS PQ41_1,2,3 0.4832V
2 VDD5 PJ6 0.1697V 17 1.05VS PJ3 0.1170V
3 VDD3 PJ8 0.1692V 18 1.2VS PQ3_1,2,3 0.1475V
4 POWER_ON PQ13_G 19 1.5VS PQ42_1,2,3 0.5618V
5 DD_ON PQ37_G 0.6700V 20 1.8VS PQ33_1,2,3 0.0733V
Remark: All the data above been used the multimeter Diode Shift to measure the signal value
Introduction of the m54ss power on sequence
CPURST#
V-CORE
1.2V
0.9VS 1,05VS
1.8V
5V
5VS
1.8VS
1.5V
VDD5
VDD3
3.3VS
1.5VS
3.3V
Position of the jumpers for M54SS ()
1.2VS
Impedance of the jumpers for M54SS ()
4.7M
0.489k
0.036K
15.5k
17.5k
0.05K
Position of the voltage dots and signals M54SS ()
PQ28(PIN1)
5V
PQ41(P1N1)
PJ6 5VS
VDD5
PJ8
VDD3
Position of the voltage dots and signals M54SS ()
PQ42(PIN1)
PQ33(PIN1)
1.5VS
PQ37(G)
DD-ON PJ7
1.8VS
1.5V
Position of the voltage dots and signals M54SS ()
PJ2
0.9VS
PJ4
1.8V
Position of the voltage dots and signals M54SS ()
PQ32(G)
SUSB#
Position of the voltage dots and signals M54SS ()
PJ1
1.2V
PJ3
1.05VS
Position of the voltage dots and signals M54SS ()
PQ3(PIN1)
1.2VS
Position of the voltage dots and signals M54SS ()
PQ16(G) PC57
VCORE-ON VCORE
Position of the voltage dots and signals M54SS ()
U19(PIN6)
U19(PIN9)
SB-PWROK
DELAY-PWRGD
PQ43(PIN1)
3.3VS
R296
NB-RST#
R299 PQ49(PIN1)
PCI-RST# 3.3V
Position of the voltage dots and signals M54SS ()
R200
CPURST
R213
H-PWRGD
Repair Trouble shooting List for M54SS
No power on
No Boot
No Power
Inspect the mb totally
Vin, Vdd3 ,Vdd5 Confirmed the impedance of
VIN VDD3 VDD5
OK
After Pwrsw#EC send out Test PWR_SW# if it is ok NG
NG
Pwrsw /DDON# DDNO# then test +3V,+5V (rising wave) and EC Replace EC &U6 orx2
+1.8V, 2.5V Frequency (x2 32.768hz)
OK
U6 Sent PWR_BTN# RSMRST# NG
To SB,then +vs voltage working NG Test SB which sent
Pwr_btn/SUSB# out susb# and check NB Replace SB
+5VS, +3VS,+2.5VS,+1.5VS
After signal susb# were outputted frequencyX4- 32,768
OK
NG
NG check the voltage of SB Replace SB Or PCI
PWRGD/Pcirst PCIRST# from south bridge
And the impedance of PCI bus lines bus linesIC
OK
Check clock ic NG
Cpurst# CPURST# (RISING WAVE) NG test digital lines ,address lines Replace NB&cpusocket
between cpusocket and Nb
No Boot
Check VCORE CLOCK NG Follow the power on sequence
CPURST# with CPU check each signal
(step by step)
&RAM(1.025v rising wave )
ok