Beruflich Dokumente
Kultur Dokumente
Power off the Network Camera as Keep the Network Camera away
soon as smoke or unusual odors are from water. If the Network Camera
detected. becomes wet, power off immediately.
Contact your distributor in the event of Contact your distributor in the event of
occurrence. occurrence.
Do not place the Network Camera Refer to your user’s manual for the
around heat sources, such as a operating temperature.
television or oven.
Keep the Network Camera away from Do not place the Network Camera in
direct sunlight. high humidity environments.
736119511H`JQ8271`RJH`WWUL`311:1521`W/2/1/joee!!!2 311:05021!!!QN!15;56;13
Do not place the Network Camera on Do not touch the Network Camera
unsteady surfaces. during a lightning storm.
736119511H`JQ8271`RJH`WWUL`311:1521`W/2/1/joee!!!3 311:05021!!!QN!15;56;15
English
1 Package Contents
736119511H`JQ8271`RJH`WWUL`311:1521`W/2/1/joee!!!4 311:05021!!!QN!15;56;17
2 Physical Description
Front Panel
Lens
Built-in Microphone
Back Panel
Audio Out
Status LED
Ethernet 10/100
RJ45 Socket Power Cord Socket
General I/O
Terminal Block
Indented Reset
Button
External/Internal MIC Switch
736119511H`JQ8271`RJH`WWUL`311:1521`W/2/1/joee!!!5 311:05021!!!QN!15;56;18
English
3 Network Deployment
3 1
1: Power +12V
2: Digital output
3: Digital input
4: Ground
POWER LINK
COLLISION RECEIVE
1 2 PARTITION
3 4 5
Ethernet Switch
736119511H`JQ8271`RJH`WWUL`311:1521`W/2/1/joee!!!6 311:05021!!!QN!15;56;19
Power over Ethernet (PoE)
When using a PoE-enabled switch
This Network Camera is PoE-compliant, allowing transmission of power and data via
a single Ethernet cable. Follow the below illustration to connect the camera to a PoE-
enabled switch via Ethernet cable.
PoE Switch
POWER LINK
COLLISION RECEIVE
1 2 PARTITION
3 4 5
POWER LINK
COLLISION RECEIVE
1 2 PARTITION
3 4 5
Non-PoE Switch
736119511H`JQ8271`RJH`WWUL`311:1521`W/2/1/joee!!!7 311:05021!!!QN!15;56;21
English
4 Assigning an IP Address
1. Install "Installation Wizard 2" from the Software Utility directory on the software CD.
2. The program will conduct an analysis of your network environment. After your network
is analyzed, please click on the "Next" button to continue the program.
IW2
Installation
Wizard 2
3. The program will search for VIVOTEK Video Receivers, Video Servers, and Network
Cameras on the same LAN.
4. After searching, the main installer window will pop up. Click on the MAC that matches
the one labeled on the bottom of your device to connect to the Network Camera via
Internet Explorer.
Network Camera
Model No: IP7160
MAC:0002D1730202 00-02-D1-73-02-02 192.168.5.151 IP7160
R o HS
This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions:
(1)This device may not cause harmful interference, and
0002D1730202
(2) this device must accept any interference received, including interference that may cause undesired operation.
736119511H`JQ8271`RJH`WWUL`311:1521`W/2/1/joee!!!8 311:05021!!!QN!15;56;22
5 Ready to Use
For further setup, please refer to the user’s manual on the software CD.
736119511H`JQ8271`RJH`WWUL`311:1521`W/2/1/joee!!!9 311:05021!!!QN!15;56;22