Beruflich Dokumente
Kultur Dokumente
continue
INDEX
6.3.2 Dimensions................................................................................. 12
6.3.3 Elaboration Methods ( Table 3 ) .................................................. 14
1. SCOPE
2. APPLICATION
3. APPLICABLE DOCUMENTS
International Standards
4. DEFINITIONS
For the purposes of this Standard, it shall be adopted the following definition :
NE 01-029
REV DATA PGINA
C DATE 29 Oct 04 PAGE 2
TABLE 3 : ELABORATION METHOD OF LETTERS, ALGARISMS
AND GRAPHICAL SIGNALS IN TECHNICAL WRITING
METHOD CHARACTERISTICS
DRAWED OR LETTERING SET MADE
1 TECHNICAL WRITING
2 DECAL TECHNICAL WRITING
3 PAINTED TECHNICAL WRITING
PANTOGRAPH OR OTHER MECHANICAL
4 METHOD MADE TECHNICAL WRITING
LEE-SMITH METHOD TECHNICAL
5 WRITING
6 GRAPHICAL COMPOSITION MACHINE
MADE TECHNICAL WRITING
CHEMICAL MILLING MADE TECHNICAL
7 WRITING
NOTE
All technical inscriptions inside aircraft shall have sharp-edged letters, algarisms
and graphical signals.
6. SPECIFIC CONDITIONS
6.1.2 DIMENSIONS
NOTE
In the case of posterior reducing of the Figure , the letters, algarisms and
graphical signals shall be elaborated with a total height A inversely proportional
to the reduction.
It shall be used method 1 for the elaboration of letters, algarisms and graphical
signals.
NE 01-029
REV DATA PGINA
C DATE 29 Oct 04 PAGE 11
6.2 TECHNICAL WRITING IN BULLETINS AND MANUALS ILLUSTRATIONS
NOTE
6.2.2 DIMENSIONS
It shall be used a total height A ( Figure 1 ) of 2,0 mm for letters, algarisms and
graphical signals in usual technical writings, and of 2,5 mm in technical writings
which shall be emphasized.
NOTES
1) In case of necessity, other total height A for letters, algarisms and graphical
signals may be used; however, A = 1,5 mm is the minimum allowable total height.
2) In the case of a posterior reducing of the illustration, the letters, algarisms and
graphical signals shall be elaborated with a total height A inversely proportional
to the reduction.
6.3.2 DIMENSIONS
6.3.2.1 INSTRUMENTS
For choosing the total height A (Figure 1) of letters, algarisms and graphical
signals, it shall be taken into consideration mainly the distance for reading. Take
also into consideration the local legibility conditions and the instrument
dimensions.
a) distance for reading varying around 700 mm : it shall be used total height A
from 3,8 mm ( minimum ) to 7,6 mm (maximum);
b) distance ( x ) for reading is very different of 700 mm : for determinate the total
height A (minimum and maximum), refer to the following formulas :
The outer insulation shall be only marked and not sectioned by the knife blade.
The braid and the inner insulation shall not be touched by the knife.
A min ( mm ) = 3,8 x
700
A max ( mm ) = 7,6 x
700
NE 01-029
REV DATA PGINA
C DATE 29 Oct 04 PAGE 12
6.3.2.2 CONTROL PANELS WITH WHITE FOREGROUND AND BLACK
BACKGROUND
NOTE
NOTE
a) a total height A ( Figure 1 ) of letters, algarisms and graphical signals from 4,8
mm (minimum) to 9.5 mm (maximum);
NE 01-029
REV DATA PGINA
C DATE 29 Oct 04 PAGE 13
6.3.2.7 COUNTER DISPLAYS
The total heights A ( Figure 1 ) of letters, algarisms and graphical signals shall
be indicated by a proficient authority.
The total height A (Figure 1) of the letters, algarisms and graphical signals shall
be, at least, equal to the total heights A (Figure 1) of the letters, algarisms and
graphical signals of the adjacent technical writings.
7. DRAWING CALLOUT
NOTES
< * > shall be indicated one of the technical writing methods ( see Table 3 )
as follows :
1 or 2 or 3 or 4 or 5 or 6 or 7.
========================
REV DATA
NE 01-029
PGINA
D DATE 16 Dec 04 PAGE 14