Beruflich Dokumente
Kultur Dokumente
Mirrors - TL
manual
Tuesday, February 16, 2016 1:32:54
1:32:52 PM Page 1 2005 Mitchell Repair Information Company, LLC.
1
2012 Acura TL
2012 ACCESSORIES & EQUIPMENT Mirrors - TL
1. Remove the front door sash inner trim (see FRONT DOOR SASH INNER TRIM REPLACEMENT ).
2. Disconnect the power mirror connector (A).
Fig. 2: Identifying Power Mirror And Power Mirror Connector With Torque Specifications
Courtesy of AMERICAN HONDA MOTOR CO., INC.
3. While holding the power mirror (B), remove the nuts securing the mirror.
4. Release the catch (A) from the hole in the door, then remove the power mirror (B).
5. Install the mirror in the reverse order of removal, and note these items:
manual
Tuesday, February 16, 2016 1:32:52 PM Page 3 2005 Mitchell Repair Information Company, LLC.
3
2012 Acura TL
2012 ACCESSORIES & EQUIPMENT Mirrors - TL
1. Carefully push on the top edge of the mirror holder (A) by hand.
2. Put a shop towel in the opening between the bottom edge of the mirror holder and the mirror housing (B)
to prevent scratches. Insert a flat-tip screwdriver under the mirror holder, and detach the bottom clips (C).
3. Carefully pull out the bottom edge of the mirror holder (A) to separate the adhesive (B), and then release
the side clips (C).
NOTE: In cold weather, gently warm the mirror holder to at least 68F (20C)
before removing it.
manual
Tuesday, February 16, 2016 1:32:52 PM Page 4 2005 Mitchell Repair Information Company, LLC.
4
2012 Acura TL
2012 ACCESSORIES & EQUIPMENT Mirrors - TL
Fig. 5: Identifying Mirror Holder, Adhesive, Side Clips, Inner Holder, Hooks And Mirror Defogger
Connectors
Courtesy of AMERICAN HONDA MOTOR CO., INC.
4. Separate the mirror holder from the inner holder (D) on the actuator by releasing the hooks (E), and
disconnect the mirror defogger connectors (F).
5. Before reinstalling the mirror holder to the inner holder (A) on the actuator, check the actuator rods (B)
and the actuator boots (C).
NOTE: Make sure each actuator rod is inserted into the actuator securely, and
each actuator boot is fully seated on the actuator.
manual
Tuesday, February 16, 2016 1:32:52 PM Page 5 2005 Mitchell Repair Information Company, LLC.
5
2012 Acura TL
2012 ACCESSORIES & EQUIPMENT Mirrors - TL
manual
Tuesday, February 16, 2016 1:32:52 PM Page 6 2005 Mitchell Repair Information Company, LLC.
6
2012 Acura TL
2012 ACCESSORIES & EQUIPMENT Mirrors - TL
Fig. 7: Identifying Mirror Harness Lower And Upper Cover, Headliner, Hooks And Rearview
Mirror Harness Cover Base
Courtesy of AMERICAN HONDA MOTOR CO., INC.
3. Loosen the TORX screw with a TORX T20 bit, then slide the rearview mirror (A) rearward and off the
mount (B).
manual
Tuesday, February 16, 2016 1:32:52 PM Page 7 2005 Mitchell Repair Information Company, LLC.
7
2012 Acura TL
2012 ACCESSORIES & EQUIPMENT Mirrors - TL
4. Install the mirror in the reverse order of removal, and note these items:
Before installing the mirror, remove the TORX screw, and apply medium strength liquid thread
lock to it.
Make sure the connector is plugged in properly.
Push the hooks into place securely.
manual
Tuesday, February 16, 2016 1:32:52 PM Page 8 2005 Mitchell Repair Information Company, LLC.
8