Beruflich Dokumente
Kultur Dokumente
Page 1 of 6
Shutdown SIS
Previous Screen
i00311829
S/N - 2PM1-UP
S/N - 2WM1-499
The pressure setting of the line relief valve in the single action hydraulic attachment circuit is set to
17700 490 kPa (2567 70 psi) at a flow rate of 150 L/min (40 US gpm) from the factory.
The specifications for the pressure, the flow rate, and the engine rpm may vary with attachment types
and/or suppliers. It is very important to follow the specifications of the supplier. Failure to follow the
specifications of the supplier could result in poor performance of the attachment.
It is important to record the appropriate engine speed when the specifications are obtained. For best
performance, use this recorded engine speed to operate the attachment.
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisweb/... 5/23/2017
307 TRACK-TYPE EXCAVATOR 2PM00001-UP (MACHINE) POWERED BY 4D32 ... Page 2 of 6
Illustration 1 g00240501
Controller Compartment
Note: Before you start to adjust the line relief valve make sure that the green light for alarm
indicating lamp (1) of controller (2) turns on.
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisweb/... 5/23/2017
307 TRACK-TYPE EXCAVATOR 2PM00001-UP (MACHINE) POWERED BY 4D32 ... Page 3 of 6
Illustration 2 g00241207
(19) Left pump pressure tap. (20) Left pump. (21) Supply line from attachment. (22) Return line from attachment.
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisweb/... 5/23/2017
307 TRACK-TYPE EXCAVATOR 2PM00001-UP (MACHINE) POWERED BY 4D32 ... Page 4 of 6
Illustration 3 g00241222
Flow Meter
(21) Supply line from attachment. (22) Return lines from attachment. (3) Flow meter. (23) Multitach. (24) Flow meter
valve.
1. Install supply line from attachment (21) to the input port of flow meter (3) .
2. Attach return line from attachment (22) to the output port of the portable flow meter (3) .
Illustration 4 g00241232
Pump Compartment
3. Attach a 49000 kPa (7100 psi) pressure gauge (15) to left pump pressure tap (19) .
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisweb/... 5/23/2017
307 TRACK-TYPE EXCAVATOR 2PM00001-UP (MACHINE) POWERED BY 4D32 ... Page 5 of 6
Illustration 5 g00241297
6. Be sure that flow meter valve (24) is in the FULLY OPEN position.
7. Start the engine and raise the hydraulic oil temperature to 55 5C (131 9F).
8. Place the power mode switch in the ON position and the engine speed dial in the HIGH IDLE
position.
9. Depress the auxiliary pedal and hold the auxiliary pedal for the remainder of the test.
10. Slowly, turn flow meter valve (24) clockwise in order to decrease the flow of oil. Record the
reading of the flow meter when the pressure reading at pressure tap (19) reaches the pressure
that is specified by the supplier of the attachment that will be used.
11. If the flow measurement is too high, go to step 12. If the flow measurement in Step 10 meets
the specification of the supplier or if the flow measurement is below the specification of the
supplier perform the following steps:
a. Slowly, turn adjustment screw (27) counterclockwise. Stop turning when the flow meter
reading starts to drop.
b. Now, turn adjustment screw (27) clockwise until the flow rate reaches the recorded
reading that was obtained above.
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisweb/... 5/23/2017
307 TRACK-TYPE EXCAVATOR 2PM00001-UP (MACHINE) POWERED BY 4D32 ... Page 6 of 6
Note: It may not always be possible to reach the specified relief pressure setting at the
flow rate that is specified by the supplier.
d. Fully, rotate flow meter valve (24) clockwise in order to stop the flow through the flow
meter. Read the pressure at pressure tap (19). This reading will be the pressure setting in
the attachment circuit for line relief valve (25) .
12. If the flow measurement is above the specification perform the following steps:
a. Turn the engine speed dial to the LOW IDLE position and gradually increase the engine
speed until the flow rate that is specified by the supplier is attained.
c. Slowly, turn adjustment screw (27) counterclockwise. Stop turning when the flow meter
reading starts to drop.
d. Turn adjustment screw (27) clockwise until the flow rate through the flow meter meets
the specification of the supplier.
f. Rotate flow meter valve (24) clockwise in order to stop the flow of oil through the flow
meter. Read the pressure at pressure tap (19). This reading will be the pressure setting in
the attachment circuit for line relief valve (25) .
Copyright 1993 - 2017 Caterpillar Inc. Tue May 23 14:35:01 UTC+0700 2017
All Rights Reserved.
Private Network For SIS Licensees.
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisweb/... 5/23/2017
307 TRACK-TYPE EXCAVATOR 2PM00001-UP (MACHINE) POWERED BY 4D32 ... Page 1 of 48
Shutdown SIS
Previous Screen
Introduction
NOTE: As a general rule, if there is a doubt as to the cause of a problem, the electronic system
should be checked first.
NOTE: For information on Systems Operation of the above, make reference to: "Systems Operation,
Electronic System", SENR6195, "Systems Operation, Hydraulic System", SENR6196 and/or
"Systems Operation, Hydraulic System", SENR9204.
NOTE: This manual contains information on the testing and adjusting procedures of the hydraulic
system in the 307 Excavator. For troubleshooting the engine components, refer to the module Service
Manual, Mitsubishi 4D32 Engine, SENR6433.
NOTE: This manual has been completely changed from the former issue. The electrical system
checking procedures and testing and adjusting procedures are now located in a separate module.
When possible, the bucket must always be lowered to the ground before
service is started. When it is necessary for the boom to be in the raised
position while tests or adjustments are done, be sure that boom, stick
and bucket have correct support.
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisweb/... 5/23/2017
307 TRACK-TYPE EXCAVATOR 2PM00001-UP (MACHINE) POWERED BY 4D32 ... Page 2 of 48
Always move the machine to a location away from the travel of other
machines. Be sure that other personnel are not near the machine when
the engine is running and tests or adjustments are being made.
During diagnosis of the hydraulic system, remember that correct oil temperature, flow and pressure
are necessary for correct operation. Pump output (oil flow) is a function of engine speed (rpm). Oil
pressure is caused by resistance to the flow of oil.
Visual Check
A visual inspection of the system is the first step when trouble-shooting a problem. Make the
inspection with the engine off and the implements lowered to the ground.
1. Check the level of the oil in the hydraulic tank. Slowly loosen the hydraulic tank air vent/fill cap
and release the pressure before the fill cap is removed.
2. Remove the filter element and check it for material that would give an indication of damage to a
component.
Pressure Checks
In each checking procedure, it is assumed that the engine operation is normal unless otherwise
specified.
Operational Tests
NOTE: For specifications given in "Operational Tests", a "NEW" specification is the performance
that can be expected for a new machine. A "REBUILD" specification is the performance target to use
after rebuilding the components of a system. A machine that performs beyond "Service Limit"
specifications should be checked for improper maintenance or adjustment, component wear, or
failure.
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisweb/... 5/23/2017
307 TRACK-TYPE EXCAVATOR 2PM00001-UP (MACHINE) POWERED BY 4D32 ... Page 3 of 48
Specifications given in charts for a machine equipped with 3700 mm (12 ft 2 in) boom, 1720 mm (5 ft
8 in) stick, and SAE 0.28 m3 (3/8 yd3) bucket.
NOTE: The power mode selector switch must be placed at MODE ON position, unless otherwise
specified, during tests.
1. Engine speed:
Excavator with no load at high idle, 1930 50 rpm (low idle switch off).
NOTE: Fully move the stick in and out several times until the hydraulic oil is at the normal
operating temperature.
Reference: Make reference to the section in this module "Relief Valves", "Specifications".
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisweb/... 5/23/2017
307 TRACK-TYPE EXCAVATOR 2PM00001-UP (MACHINE) POWERED BY 4D32 ... Page 4 of 48
Test Preparation:
1. Set engine speed and increase the hydraulic oil temperature to 55 5C (131 9F).
2. The travel test ground must be hard and level as possible. A minimum test length of 25 m (82.5 ft)
is required.
3. Draw a 25 m (82.5 ft) straight line on travel test ground as a reference line.
4. Position the machine so that one track is in line (parallel) with the reference line. Put the machine
in the travel test position as shown in the illustration.
Test Procedure:
1. Start the engine and place the power mode selector switch in MODE III position. Place the engine
speed dial at position "10" and the travel speed switch in HIGH (rabbit) position. Move the machine
by operating both travel levers at the same time.
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisweb/... 5/23/2017
307 TRACK-TYPE EXCAVATOR 2PM00001-UP (MACHINE) POWERED BY 4D32 ... Page 5 of 48
2. The first 5 m (16.5 ft) are for a preliminary run. Measure the time required for the machine to travel
the remaining 20 m (66 ft) in each direction (forward and reverse).
4. Repeat the above procedure with the travel speed switch in LOW (tortoise) position.
NOTE: The following chart represents the time (in seconds) it should take to complete the 20 m (66
ft) test run:
NOTE: The following chart represents the travel deviation from the reference line:
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisweb/... 5/23/2017
307 TRACK-TYPE EXCAVATOR 2PM00001-UP (MACHINE) POWERED BY 4D32 ... Page 6 of 48
Test Preparation:
1. Set engine speed and increase the hydraulic oil temperature to 55 5C (131 9F).
Test Procedure:
1. Start the engine and place the load selector switch in HIGH LOAD position. Run the raised track
with the engine speed dial at HIGH IDLE position and the travel speed switch in HIGH (rabbit)
position.
2. Measure the time required for the track to make three complete turns (revolutions) in each direction
(forward and reverse).
3. Repeat the above procedure with the travel speed switch in LOW (tortoise) position.
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisweb/... 5/23/2017
307 TRACK-TYPE EXCAVATOR 2PM00001-UP (MACHINE) POWERED BY 4D32 ... Page 7 of 48
Drift On Slope
Measuring the amount of drift of the machine on a slope will determine if there is a need to check the
travel brake.
Test Preparation:
1. Place the machine on a slope of 12. The slope surface must be hard and smooth.
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisweb/... 5/23/2017
307 TRACK-TYPE EXCAVATOR 2PM00001-UP (MACHINE) POWERED BY 4D32 ... Page 8 of 48
Test Procedure:
1. Put marks on both track and ground to indicate its relative position to the slope.
3. Measure (with a scale) the distance the tracks have moved on the slope.
Measuring the swing speed and over swing of the machine will determine if there is a need to check
the swing motor and/or anti-reaction valve.
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisweb/... 5/23/2017
307 TRACK-TYPE EXCAVATOR 2PM00001-UP (MACHINE) POWERED BY 4D32 ... Page 9 of 48
Test Preparation:
1. Set engine speed and increase the hydraulic oil temperature to 55 5C (131 9F).
3. Put marks on both inner and outer races of the swing bearing to indicate relation of two positions.
2. Move the swing control lever to the RIGHT or LEFT until the machine completes a 180 swing
operation and measure the amount of drift (over swing) by measuring the distance between the marks
on the swing bearing.
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisweb/... 5/23/2017
307 TRACK-TYPE EXCAVATOR 2PM00001-UP (MACHINE) POWERED BY 4D3... Page 10 of 48
NOTE: Use a reference point that is visible from the operator's seat as a indicator of when to stop the
180 rotation.
Measuring the swing speed on a slope will determine if there is a need to check the swing motor
and/or anti-reaction valve. Measuring the swing drift on a slope will determine if there is a need to
check the swing parking brake.
Test Preparation:
1. Place the machine on a 12 slope.
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisweb/... 5/23/2017
307 TRACK-TYPE EXCAVATOR 2PM00001-UP (MACHINE) POWERED BY 4D3... Page 11 of 48
2. Fill the bucket with soil and place the implements to maximum reach. The bucket should be
positioned above the ground to clear any obstructions.
2. Measure the time needed to swing the upper structure 90 counterclockwise up hill. Do the same
for a 90 turn clockwise up hill.
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisweb/... 5/23/2017
307 TRACK-TYPE EXCAVATOR 2PM00001-UP (MACHINE) POWERED BY 4D3... Page 12 of 48
2. Place the upper structure at a 90 angle to the tracks as shown in the illustration.
3. Put marks on the inner and outer races of the swing bearing.
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisweb/... 5/23/2017
307 TRACK-TYPE EXCAVATOR 2PM00001-UP (MACHINE) POWERED BY 4D3... Page 13 of 48
5. Leave the machine in this position for three minutes, and measure swing drift on the circumference
of the swing bearing.
6. Rotate the upper structure 180 from the original position as described in Step 1.
Cylinder Drift
Test Preparation:
1. Set engine speed and increase the hydraulic oil temperature to 55 5C (131 9F).
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisweb/... 5/23/2017
307 TRACK-TYPE EXCAVATOR 2PM00001-UP (MACHINE) POWERED BY 4D3... Page 14 of 48
3. Raise the boom until its upper surface becomes parallel to the ground.
6. Leave the machine in this position for three minutes, then measure each cylinder's length from pin
to pin for drift.
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisweb/... 5/23/2017
307 TRACK-TYPE EXCAVATOR 2PM00001-UP (MACHINE) POWERED BY 4D3... Page 15 of 48
2. Raise the boom high enough until the stick is perpendicular to the ground.
5. Leave the machine in this position for three minutes, then measure each cylinder's length from pin
to pin for drift.
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisweb/... 5/23/2017
307 TRACK-TYPE EXCAVATOR 2PM00001-UP (MACHINE) POWERED BY 4D3... Page 16 of 48
2. Raise the boom high enough until the stick is perpendicular to the ground.
6. Leave the machine in this position for three minutes then measure the cylinder length from pin to
pin for drift.
Test Preparation:
1. Place the machine on level ground.
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisweb/... 5/23/2017
307 TRACK-TYPE EXCAVATOR 2PM00001-UP (MACHINE) POWERED BY 4D3... Page 17 of 48
Extension test;
Measure the time required for the boom cylinders to reach full extension position starting with the
bucket on the ground.
Retraction test;
Measure the time required for the bucket to come in contact with the ground from the full extension
position of the boom cylinders.
Extension test;
Measure the time required for the stick cylinder to reach full extension position from full retraction
position.
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisweb/... 5/23/2017
307 TRACK-TYPE EXCAVATOR 2PM00001-UP (MACHINE) POWERED BY 4D3... Page 18 of 48
Retraction test;
Measure the time required for the stick cylinder to reach full retraction position from full extension
position.
Extension test;
Measure the time required for the bucket cylinder to reach full extension position from full retraction
position.
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisweb/... 5/23/2017
307 TRACK-TYPE EXCAVATOR 2PM00001-UP (MACHINE) POWERED BY 4D3... Page 19 of 48
Retraction test;
Measure the time required for the bucket cylinder to reach full retraction position from full extension
position.
Extension test;
Measure the time required for the blade cylinder to reach full extension position from full retraction
position.
Retraction test;
Measure the time required for the blade cylinder to reach full retraction position from full extension
position.
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisweb/... 5/23/2017
307 TRACK-TYPE EXCAVATOR 2PM00001-UP (MACHINE) POWERED BY 4D3... Page 20 of 48
2. Adjust the position of the bucket so that it will be flat on the ground when the boom is lowered.
4. Shut off the engine and put the hydraulic activation control lever in the UNLOCK position.
5. Move the control levers for boom, stick, and swing to all FULL STROKE positions. This will
release any pressure that might be present in the pilot system.
6. Slowly loosen the air vent plug on the hydraulic tank and release the pressure.
8. The pressure in the hydraulic system has now been released and lines and components can be
removed.
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisweb/... 5/23/2017
307 TRACK-TYPE EXCAVATOR 2PM00001-UP (MACHINE) POWERED BY 4D3... Page 21 of 48
NOTE: No attempt should be made to start the engine until the main pumps have been filled with
hydraulic oil, or serious damage can be caused to hydraulic components.
Pump Compartment
(1) Air vent plug.
1. With the engine stopped, remove air vent plug (1) on the top of the main pump. Leave the plug off
for several minutes until the main pumps are filled with hydraulic oil. After the pumps are filled with
oil, tighten the vent plug and start the engine. With the engine at low idle, fully raise the boom and
hold it in this position.
2. Stop the engine and slowly lower the boom until the bucket is on the ground. This pressurizes the
hydraulic tank.
3. Slowly loosen the air vent plug several turns until oil flows out of the plug opening. This is an
indication that the air has completely been released from the pumps.
Pressure Specifications
NOTE: A new or rebuilt machine must perform according to New or Rebuild Specifications. A
machine that performs beyond Service Limit Specifications must be checked for improper
adjustment, wear, or damage of relief valves or pumps.
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisweb/... 5/23/2017
307 TRACK-TYPE EXCAVATOR 2PM00001-UP (MACHINE) POWERED BY 4D3... Page 22 of 48
NOTE: Values given above are approximate. Use a pressure gauge for adjustment.
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisweb/... 5/23/2017
307 TRACK-TYPE EXCAVATOR 2PM00001-UP (MACHINE) POWERED BY 4D3... Page 23 of 48
Pump Compartment
(1) Tap (right pump). (2) Tap (left pump).
2. Release the pressure in the hydraulic system according to the section, "Release Of Pressure In The
Hydraulic System".
3. Connect a 40 000 kPa (5800 psi) pressure gauge to either main pump tap (1) or tap (2).
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisweb/... 5/23/2017
307 TRACK-TYPE EXCAVATOR 2PM00001-UP (MACHINE) POWERED BY 4D3... Page 24 of 48
4. Temporary set the main relief valve pressure higher than the line relief valves.
NOTE: The purpose for "Temporary Setting Of The Main Relief Pressure" is done so implement line
relief valves can be adjusted.
5. Disconnect hose (4) from main relief valve (8). Install a plug (7/16-20 UN) (9S-5518) in the open
end of hose (4). Install a cap (7/16-20 UN) (9L-8493) to the opening of main relief valve (8).
6. Start the engine and move the stick in and out to its full travel position. Do this operation several
times until the hydraulic oil temperature reaches the normal operating temperature of 55 5C (131
9F).
8. Place the engine speed dial at HIGH IDLE position. Make sure that engine speed under no load is
1930 50 rpm.
NOTE: Normal operations (see characteristic curve) of the engine and pumps are necessary for the
pressure adjustment. If the results of the pressure adjustment are not correct, then check the engine
and pump characteristic curve.
9. Slowly move the bucket control lever to the BUCKET OPEN position (full cylinder rod retraction).
10. Check to be sure the main relief valve pressure setting is 27 500 490 kPa (4000 72 psi).
11. Loosen locknut (7) and turn plug (6) clockwise a quarter turn. The pressure gauge at tap (1) or (2)
should read 33 300 kPa (4850 psi). Tighten locknut (7) to specification.
NOTE: Turning plug (6) clockwise increases the pressure. Turning plug (6) counterclockwise
decreases the pressure.
2. Use the pressure gauge at tap (2) to read the line relief pressure for boom and bucket circuits. Use
the pressure gauge at tap (1) to read the line relief pressure for stick circuit. For line relief pressure
settings for the implement circuits, see the section in this module, "Pressure Specifications".
NOTE: After adjustment of the line relief valves, return the main relief pressure to its normal setting.
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisweb/... 5/23/2017
307 TRACK-TYPE EXCAVATOR 2PM00001-UP (MACHINE) POWERED BY 4D3... Page 25 of 48
Stick cylinder head end line relief valve (9), boom cylinder rod end line relief valve (10) and bucket
cylinder head end line relief valve (11) are located on the top of the main relief valves.
NOTE: The stick cylinder rod end line relief valve and boom cylinder head end line relief valve are
located under the main control valves.
1. To adjust the pressure in the stick cylinder rod end, move the stick control lever to FULL STICK
OUT (rod retracted) position. Check the pressure in the stick cylinder rod end at tap (1).
2. Return the stick control lever to the NEUTRAL position. Loosen locknut (12) and turn screw (13)
until the line relief valve pressure gauge at tap (1) reads 30 900 1470 kPa (4500 215 psi). Turning
screw (13) clockwise increases the pressure and turning screw (13) counterclockwise decreases the
pressure.
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisweb/... 5/23/2017
307 TRACK-TYPE EXCAVATOR 2PM00001-UP (MACHINE) POWERED BY 4D3... Page 26 of 48
3. To adjust the line relief pressure in the stick cylinder head end, move the stick control lever to
FULL STICK IN (rod extended) position. Check the pressure at tap (1).
4. Return the stick control lever to the NEUTRAL position. Adjust the line relief valve pressure in the
same manner as the stick cylinder rod end.
NOTE: After adjustment of the line relief valves, return the main relief pressure to its normal setting.
1. To adjust the pressure in the bucket cylinder head end move the bucket control lever to FULL
BUCKET CLOSE (rod extended) position. Check the pressure in the bucket cylinder head end at tap
(2).
2. Return the bucket control lever to the NEUTRAL position. Adjust the line relief valve pressure in
the same manner as described for the stick cylinder.
NOTE: After adjustment of the line relief valves, return the main relief pressure to its normal setting.
1. To adjust the pressure in the boom cylinder head end, move the boom control lever to FULL
BOOM RAISE (rod extended) position. Check the pressure in the boom cylinder head end at tap (2).
2. Return the boom control lever to the NEUTRAL position. Adjust the line relief valve pressure in
the same manner as described for the stick cylinder.
3. To adjust the pressure in the boom cylinder rod end, move the boom control lever to FULL BOOM
DOWN (rod retracted) position. Check the pressure at tap (2).
4. Return the boom control lever to the NEUTRAL position. Adjust the line relief valve pressure
using the same procedure as that described for the stick cylinder.
NOTE: After adjustment of the line relief valves, return the main relief pressure to its normal setting.
NOTE: If an appropriate location is not available for full retraction of the boom cylinder perform the
alternate adjustment procedure.
1. To adjust the pressure in the boom cylinder head end, move the boom control lever to FULL
BOOM RAISE (rod extended) position. Check the pressure in the boom cylinder head end at tap (2).
2. Return the boom control lever to the NEUTRAL position. Adjust the line relief valve pressure in
the same manner as described for the stick cylinder.
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisweb/... 5/23/2017
307 TRACK-TYPE EXCAVATOR 2PM00001-UP (MACHINE) POWERED BY 4D3... Page 27 of 48
3. Stop the engine. Release the pressure in the hydraulic system. See the section, "Release Of Pressure
In The Hydraulic System".
4. Reverse the location of the line relief valves of the head end and rod end by switching the valves.
5. To adjust the pressure in the boom cylinder head end, move the boom control lever to FULL
BOOM RAISE (rod extended) position. Check that the pressure in the boom cylinder head end at tap
(2) is to the boom rod end line relief pressure specification.
6. Return the boom control lever to the NEUTRAL position. Adjust the line relief valve pressure in
the same manner as described for the stick cylinder.
7. Stop the engine. Release the pressure in the hydraulic system. See the section, "Release Of Pressure
In The Hydraulic System".
NOTE: After adjustment of the line relief valves, return the main relief pressure to its normal setting.
2. Remove the plug (7/16-20 UN) (9S-5518) from hose (4). Remove the cap (7/16-20 UN) (9L-8493)
from main relief valve (8).
4. Adjust the main relief valve pressure to the normal setting. See "Main Relief Valve Check And
Adjustment" section in this module.
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisweb/... 5/23/2017
307 TRACK-TYPE EXCAVATOR 2PM00001-UP (MACHINE) POWERED BY 4D3... Page 28 of 48
Pump Compartment
(1) Tap (right pump). (2) Tap (left pump).
2. Release the pressure in the hydraulic system. See the section, "Release Of Pressure In The
Hydraulic System".
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisweb/... 5/23/2017
307 TRACK-TYPE EXCAVATOR 2PM00001-UP (MACHINE) POWERED BY 4D3... Page 29 of 48
b. Install a cap (7/16-20 UN) (9L-8493) on elbow (18). Leave the end of pilot line (19) open to the
air.
5. Start the engine and place the engine speed dial at high idle position with the load selector switch at
HIGH LOAD position.
6. Increase the hydraulic oil temperature to the normal operating temperature of 55 5C (131 9F).
Check Procedure
1. Slowly move the swing control lever for a full left swing operation and check the pressure of relief
valve (14).
NOTE: Check to be sure that the swing parking brake is engaged while the swing control is activated.
2. Return the swing control lever to the NEUTRAL position. Loosen locknut (15) of relief valve (14)
and turn setscrew (17) until the pressure gauge at tap (1) reads 20 600 980 kPa (3000 140 psi).
Turning setscrew (17) clockwise increases the pressure and turning setscrew (17) counterclockwise
decreases the pressure.
3. To adjust the relief pressure for right swing, slowly move the control lever to a full right swing
operation and check the pressure of relief valve (16).
4. Return the swing control lever to the NEUTRAL position. Adjust the relief valve pressure in the
same manner as the swing left relief valve.
a. Stop the engine and release the pressure in the hydraulic system. See the section, "Release Of
Pressure In The Hydraulic System".
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisweb/... 5/23/2017
307 TRACK-TYPE EXCAVATOR 2PM00001-UP (MACHINE) POWERED BY 4D3... Page 30 of 48
Adjustment Procedure
Relief Valve
(15) Locknut. (17) Setscrew. (20) Body. (21) Spring. (22) Check valve. (23) Valve. (24) Piston. (25) Shim. (26) Spring.
(27) Spring. (28) Sleeve.
1. Stop the engine and release the pressure in the hydraulic system. See the section, "Release Of
Pressure In The Hydraulic System".
NOTE: Relief valves (14) and (16) are identical in construction and operation.
2. Remove body (20), spring (21), check valve (22), valve (23), springs (26) and (27) and sleeve (28)
of relief valve (14) and/or (16) as a unit.
3. Remove spring (21), check valve (22), valve (23), springs (26) and (27) and sleeve (28) from body
(20) as a unit.
4. Make an adjustment to shim(s) (25) on the right end face of piston (24) until the specified relief
pressure setting is obtained. A change of 0.1 mm (0.004 in) thickness in shim (25) changes the swing
relief pressure by approximately 590 kPa (86 psi).
5. Install spring (21), check valve (22), valve (23), springs (26) and (27) and sleeve (28) in body (20).
Then install the whole unit to the swing motor. Tighten the relief valve to a torque of 39 4 Nm (29
3 lb ft).
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisweb/... 5/23/2017
307 TRACK-TYPE EXCAVATOR 2PM00001-UP (MACHINE) POWERED BY 4D3... Page 31 of 48
NOTE: Pressure adjustments to the main relief valve should be done by first adjusting the travel
operation of the main relief valve and then adjusting the implement operation of the main relief valve.
Any adjustment to the travel operation of the main relief valve will change the pressure setting to the
implement operation of the main relief valve.
Pump Compartment
(1) Tap (right pump). (2) Tap (left pump).
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisweb/... 5/23/2017
307 TRACK-TYPE EXCAVATOR 2PM00001-UP (MACHINE) POWERED BY 4D3... Page 32 of 48
2. Release the pressure in the hydraulic system. See the section, "Release Of Pressure In The
Hydraulic System".
3. Disconnect hose (4) from main relief valve (8). Install a plug (7/16-20 UN) (9S-5518) in the open
end of hose (4). Install a cap (7/16-20 UN) (9L-8493) to the opening of main relief valve (8).
5. Start the engine and place the engine speed dial at HIGH IDLE position with the load selector
switch at HIGH LOAD position.
1. Block forward left travel by installing a approximately 57 mm (2.25 in) diameter pin (30) in
position on the gear of sprocket (29).
2. Loosen locknut (5) and turn plug (3) clockwise until it bottoms out. Tighten locknut (5).
3. Slowly move the left travel control lever to FULL FORWARD position and check main relief
valve pressure at tap (2).
4. Return the control lever to the NEUTRAL position. Loosen locknut (7) and turn plug (6) until the
pressure gauge at tap (2) reads 31 400 490 kPa (4550 72 psi). Tighten locknut (7) to a torque of
83 5 Nm (60 4 lb ft).
Reference: Turning plug (6) clockwise increases the pressure and turning plug (6) counterclockwise
decreases the pressure.
5. Adjust the main relief valve pressure for the implement circuits. See the next topic for the main
relief valve adjustment procedure for the implement circuits.
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisweb/... 5/23/2017
307 TRACK-TYPE EXCAVATOR 2PM00001-UP (MACHINE) POWERED BY 4D3... Page 33 of 48
2. Return the bucket control lever to the NEUTRAL position and adjust main relief valve pressure to
27 500 490 kPa (4000 72 psi).
3. To adjust, loosen locknut (5) and turn plug (3) until the pressure gauge at tap (2) reads 27 500
490 kPa (4000 72 psi). Tighten locknut (5) to a torque of 64 5 Nm (47 4 lb ft).
Reference: Turning plug (3) clockwise increases the pressure and turning plug (3) counterclockwise
decreases the pressure.
4. Stop the engine. Release the pressure in the hydraulic system. See the section, "Release Of Pressure
In The Hydraulic System".
5. Remove the plug (7/16-20 UN) (9S-5518) from hose (4). Remove the cap (7/16-20 UN) (9L-8493)
from main relief valve (8).
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisweb/... 5/23/2017
307 TRACK-TYPE EXCAVATOR 2PM00001-UP (MACHINE) POWERED BY 4D3... Page 34 of 48
2. Release the pressure in the hydraulic system. See the section in this module "Release Of Pressure
In The Hydraulic System".
a. Slowly move the blade control lever to the BLADE FULL RAISE position. Check the pressure at
tap (35).
c. Loosen locknut (41) and turn screw (39) until the pressure gauge at tap (35) reads 21 600 kPa (3150
psi). Turning screw (39) clockwise increases the pressure and turning screw (39) counterclockwise
decreases the pressure. Tighten locknut (41) to a torque of 29 2 Nm (21 1 lb ft).
8. Slowly move the blade control lever to the BLADE FULL LOWER position. Check the pressure at
tap (35). Return the blade control lever to the NEUTRAL position.
9. Loosen locknut (36) of blade line relief valve (40). Turn screw (38) until the pressure gauge at tap
(35) reads 19 100 490 kPa (2750 72 psi). Turning screw (38) clockwise increases the pressure and
turning screw (38) counterclockwise decreases the pressure. Tighten locknut (36) to a torque of 29
2 Nm (21 1 lb ft).
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisweb/... 5/23/2017
307 TRACK-TYPE EXCAVATOR 2PM00001-UP (MACHINE) POWERED BY 4D3... Page 35 of 48
3. Loosen locknut (41) and turn screw (39) until the pressure gauge at tap (35) reads 17 200 490
kPa (2500 72 psi). Tighten locknut (41) to a torque of 29 2 Nm (21 1 lb ft).
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisweb/... 5/23/2017
307 TRACK-TYPE EXCAVATOR 2PM00001-UP (MACHINE) POWERED BY 4D3... Page 36 of 48
Check Procedure
To check the swing motor performance, measure the amount of swing motor case drain oil as follows:
1. Stop the engine. Release the pressure in the hydraulic system. See the section, "Release Of Pressure
In The Hydraulic System".
2. Disconnect case drain line (2) from tee (3) on the swing motor.
3. Install a plug (9/16-18UN) in the end of case drain line (2) and a cap (9/16-18UN) in the open end
of tee (3).
4. Disconnect case drain line (1) from the swivel. Put the open end of case drain line (1) into a
suitable measuring container.
a. Disconnect pilot line (5) from elbow (4). Leave the end of pilot line (5) open to the air.
7. Start and run the engine at high idle speed of 1930 50 rpm with the load selector switch at HIGH
LOAD position.
9. Operate the swing control lever for one minute. Measure the amount of swing motor case drain oil.
NOTE: Check to be sure the swing parking brake is correctly being engaged while the swing control
is activated.
a. Stop the engine and release the pressure in the hydraulic system. See the section, "Release Of
Pressure In The Hydraulic System".
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisweb/... 5/23/2017
307 TRACK-TYPE EXCAVATOR 2PM00001-UP (MACHINE) POWERED BY 4D3... Page 37 of 48
11. Operate the swing control to place the swing motor barrel at a new position.
12. Repeat steps 1 through 10. Take three measurements at three different swing motor barrel
positions.
Expected Result
NOTE: The maximum acceptable case drain oil at each measuring point with a swing relief pressure
setting of 20 600 980 kPa (3000 140 psi) must be:
Travel Motor
(1) Connector. (2) Drain line.
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisweb/... 5/23/2017
307 TRACK-TYPE EXCAVATOR 2PM00001-UP (MACHINE) POWERED BY 4D3... Page 38 of 48
Check Procedure
To check the travel motor performance, measure the amount of case drain as follows:
1. Stop the engine. Release the pressure in the hydraulic system. See the section, "Release Of Pressure
In The Hydraulic System".
2. Disconnect drain line (2) from connector (1). Install a plug (9/16-18 UN) in the open end of drain
line (2).
3. Connect one end of the vinyl hose to connector (1) and put the other end of the vinyl hose into a
suitable measuring container.
4. Start and run the engine at high idle speed of 1930 50 rpm with the load selector switch at HIGH
LOAD position.
6. With the track blocked, operate the travel control for one minute.
8. Remove the track block, and move the machine forward to place the travel motor barrel in a new
position.
9. Repeat steps 1 through 7. Take three measurements at three different measuring points.
Expected Result
NOTE: The maximum acceptable case drain oil at each measuring point with a main relief pressure
of 31 400 490 kPa (4550 72 psi) must be:
Pilot Circuit
Pilot Relief Valve Pressure Check And Adjustment
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisweb/... 5/23/2017
307 TRACK-TYPE EXCAVATOR 2PM00001-UP (MACHINE) POWERED BY 4D3... Page 39 of 48
2. Release the pressure in the hydraulic system according to the section, "Release Of Pressure In The
Hydraulic System".
NOTE: Normal operations (see characteristic curve) of the engine and pumps are necessary for the
pressure adjustment. If the results of the pressure adjustment are not correct, then check the engine
and pump characteristic curve.
2. To adjust the pilot relief valve pressure, loosen locknut (34) of pilot relief valve (32).
3. Turn setscrew (33) until the pressure gauge reads 3450 + 200 - 0 kPa (500 + 29 - 0 psi). Turning
setscrew (33) clockwise increases the pressure and turning setscrew (33) counterclockwise decreases
the pressure.
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisweb/... 5/23/2017
307 TRACK-TYPE EXCAVATOR 2PM00001-UP (MACHINE) POWERED BY 4D3... Page 40 of 48
NOTE: If operational tests (for example cycle times) indicate that a slow implement problem is
common to the circuits of one pump, then the problem is most likely in the hydraulic system. Then
perform the "Pump Performance Check And Adjustment".
NOTE: If the operational tests indicate an implement speed problem common to both pump circuits,
then the engine, fuel, or working altitude may be the problem.
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisweb/... 5/23/2017
307 TRACK-TYPE EXCAVATOR 2PM00001-UP (MACHINE) POWERED BY 4D3... Page 41 of 48
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisweb/... 5/23/2017
307 TRACK-TYPE EXCAVATOR 2PM00001-UP (MACHINE) POWERED BY 4D3... Page 42 of 48
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisweb/... 5/23/2017
307 TRACK-TYPE EXCAVATOR 2PM00001-UP (MACHINE) POWERED BY 4D3... Page 43 of 48
Pump Compartment
(17) Outlet line (right pump). (25) Tap (right pump). (30) Tee. (32) Pilot line. (34) Connector (right pump).
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisweb/... 5/23/2017
307 TRACK-TYPE EXCAVATOR 2PM00001-UP (MACHINE) POWERED BY 4D3... Page 44 of 48
2. Release the pressure in the hydraulic system. See the section in this module "Release Of Pressure
In The Hydraulic System".
3. Install the following tools in accordance with flow meter tool layout illustration and circuit
diagram.
a. Disconnect outlet line (17) from connector (34) of right pump (19).
c. Disconnect makeup line (23) from elbow (22) of swing motor (21).
d. Install tee (16) and O-ring seal (15) to elbow (22). Connect makeup line (23) and O-ring seal (15)
to tee (16).
e. Connect portable hydraulic tester (1) between connector (34) and tee (16).
f. Disconnect pilot line (32) from tee (30). Leave the open end of pilot line (32) to the air. Install cap
(7/16-20 UN) (9L-8493) (33) to tee (30).
g. Install a 49 000 kPa (7100 psi) pressure gauge (27) at right pump tap (25).
Right Console
(36) High Load position. (37) Load selector switch.
4. Start the engine and place the load selector switch (37) in HIGH LOAD position (36).
5. Place the engine speed dial at HIGH IDLE position and maintain the maximum no load speed at
1930 50 rpm.
6. Increase the hydraulic oil temperature to 55 5C (131 9F). To increase the oil temperature,
move the stick IN and OUT to its full travel several times.
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisweb/... 5/23/2017
307 TRACK-TYPE EXCAVATOR 2PM00001-UP (MACHINE) POWERED BY 4D3... Page 45 of 48
Pump Compartment
(26) Tap (left pump). (30) Tee. (32) Pilot line. (38) Elbow (left pump).
Perform the same preparation as that described for the right pump flow test except Step 3. Use the
following procedure in replacement for Step 3, for left pump (20).
a. Disconnect outlet line (18) from elbow (38) of left pump (20).
c. Disconnect makeup line (23) from elbow (22) of swing motor (21).
d. Install tee (16) and O-ring seal (15) to elbow (22). Connect makeup line (23) and O-ring seal (15)
to tee (16).
e. Connect portable hydraulic tester (1) between elbow (38) and tee (16).
f. Disconnect pilot line (32) from tee (30). Leave the open end of pilot line (32) to the air. Install cap
(7/16-20 UN) (9L-8493) (33) to tee (30).
g. Install a 49 000 kPa (7100 psi) pressure gauge (27) at left pump tap (26).
4. Start the engine and place the load selector switch (37) in HIGH LOAD position (36).
5. Place the engine speed dial at HIGH IDLE position and maintain the maximum no load speed at
1930 50 rpm.
6. Increase the hydraulic oil temperature to 55 5C (131 9F). To increase the oil temperature,
move the stick IN and OUT to its full travel several times.
Check Procedure
NOTE: Perform the upper and lower pump flow tests one at a time.
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisweb/... 5/23/2017
307 TRACK-TYPE EXCAVATOR 2PM00001-UP (MACHINE) POWERED BY 4D3... Page 46 of 48
1. Slowly turn valve (35) of portable hydraulic tester (1) clockwise and record pump flow at each of
the following pressure points. Use pressure gauge (27) at tap (25) or (26) for this reading.
NOTE: Flow specifications given above are based on an engine speed of 1800 rpm. To get more
accurate test results, each of measurements should be corrected by calculating as follows:
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisweb/... 5/23/2017
307 TRACK-TYPE EXCAVATOR 2PM00001-UP (MACHINE) POWERED BY 4D3... Page 47 of 48
NOTE: Any flow variation per one turn of a setscrew should be used as a guide only. Always use a
flow meter to adjust the pump flow.
Pump Compartment
(39) Locknut. (40) Setscrew.
Pump Regulator
(39) Locknut. (40) Setscrew. (41) Shim.
2. Turn setscrew (40) until adjusted to the correct specification. Turning setscrew (40) clockwise
increases the flow rate. Turning setscrew (40) counterclockwise decreases the flow rate by the same
amount as shown in the clockwise rotation. A quarter turn of setscrew (40) changes flow rate as
follows:
a. Approximately 1.8 liter/min (0.5 U.S.gpm) at a system pressure of 13 700 kPa (1975 psi) where the
constant horsepower control activates at the first stage.
b. Approximately 1.5 liter/min (0.4 U.S.gpm) at a system pressure of 31 400 kPa (4550 psi) where the
constant horsepower control activates at the second stage.
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisweb/... 5/23/2017
307 TRACK-TYPE EXCAVATOR 2PM00001-UP (MACHINE) POWERED BY 4D3... Page 48 of 48
c. For adjustment at the point where the activation of the constant horsepower control changes from
the first stage to the second stage, use shim (41). A change of a 0.1 mm (0.004 in) shim thickness
changes flow rate by approximately 0.3 liter/min (0.1 U.S.gpm).
Copyright 1993 - 2017 Caterpillar Inc. Tue May 23 14:34:13 UTC+0700 2017
All Rights Reserved.
Private Network For SIS Licensees.
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisweb/... 5/23/2017
307 TRACK-TYPE EXCAVATOR 2PM00001-UP (MACHINE) POWERED BY 4D32 ... Page 1 of 3
Shutdown SIS
Previous Screen
i00317096
S/N - 2PM257-UP
4. Raise the boom until the upper surface of the boom at the stick end becomes parallel to the
ground. Stop the engine.
6. Measure the boom cylinder drift. The drift rate of the boom cylinder should be less than .002
meter per minute (0.08 inch per minute).
4. Raise the boom until the upper surface of the boom at the stick end becomes parallel to the
ground. Stop the engine.
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisweb/... 5/23/2017
307 TRACK-TYPE EXCAVATOR 2PM00001-UP (MACHINE) POWERED BY 4D32 ... Page 2 of 3
Note: The following steps must be done to the right check and relief valve and the left check
and relief valve at the same time.
Illustration 1 g00244799
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisweb/... 5/23/2017
307 TRACK-TYPE EXCAVATOR 2PM00001-UP (MACHINE) POWERED BY 4D32 ... Page 3 of 3
7. The boom should lower slowly and no oil leakage should be found.
Test The Relief Valve For The Boom Cylinder Head End
Refer to Testing and Adjusting, SENR9205-01 for information on testing the relief valve for the
boom cylinder head end.
Copyright 1993 - 2017 Caterpillar Inc. Tue May 23 14:36:01 UTC+0700 2017
All Rights Reserved.
Private Network For SIS Licensees.
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisweb/... 5/23/2017