Sie sind auf Seite 1von 46

TECHNICAL DOCUMENTATION FRONT SHEET

BP EXPLORATION
(SHAH DENIZ) LIMITED

SHAH DENIZ STAGE 2 PROJECT

TECHNICAL SPECIFICATION
FOR
JOTUN PAINTS

A09 19/10/15 Issue for Approval Jotun Paints KSM KSM


A08 15/09/15 Issue for Approval Jotun Paints KSM KSM
A07 31-03-2015 Issue for Approval Jotun Paints KSM KSM
A06 27-10-2014 Issue for Approval Jotun Paints KSM KSM
A05 22-09-2014 Issue for Approval Jotun Paints KSM KSM
A04 29-08-2014 Issue for Approval Jotun Paints KSM KSM
Jotun
A03 26-08-2014 Issue for Approval KSM KSM
Paints
Jotun
A02 09-07-2014 Issue for Approval KSM KSM
Paints
Jotun
A01 26-05-2014 Issue for Review KSM KSM
Paints

Rev Date Reason for Issue Prepared Checked Approved Prepared Reviewed Approved

Notes: Disc. Disc.


Contr. Rep Author Disc SPA
Eng. Lead
Keppel Singmarine BP

Category Code Description

Location Code SVNVSV SCV New Build

Document Type SPE Specification

System Number N/A Not Applicable

This document shall not be reproduced without Location Doc. Sequenc Sheet
Company Disc Rev.
permission of BP Exploration (Shah Deniz) Ltd Code Type e No. No.

KF SVNVSV MP SPE 0009 000 A09


KF-SVNVSV-MP-SPE-0009-000 Rev A09 SHAH DENIZ STAGE 2 PROJECT
TECHNICAL SPECIFICATION FOR JOTUN PAINTS

Revision History and Hold Record


Revision History
Rev. Ref.
Date Detailed Description of Change
No. Section
26-05-2014 A01 Issue for Issue
09-07-2014 A02 Issue for Approval
26-08-2014 A03 Issue for Approval
29-08-2014 A04 Issue for Approval
22-09-2014 A05 Issue for Approval
27-10-2014 A06 Issue for Approval
31-03-2015 A07 Issue for Approval
15/09/15 A08 Issue for Approval
19/10/15 A09 Issue for Approval

Hold Record
Ref.
Hold Ref. Description / Reason for Hold
Section
Jotspec
Technical specification
Newbuilding

Owner: Vessel name: H386 SUBSEA CONSTRUCTION VESSEL


Yard: BAKU SHIPYARD IMO: Version: 9
Management: Hull no: H386 Date: 09-Oct-15
Project: NB-Keppel Singmarine-H386-(+)-155-M-Supply/Anchor handling & misc..- Supply in Baku Shipyard
Prepared by: James Yong - Jotun (Singapore) Pte. Ltd.

Page 1 of 44
Summary

Project NB-Keppel Singmarine-H386-(+)-155-M-Supply/Anchor Prepared by James Yong - Jotun (Singapore) Pte. Ltd.
handling & misc..- Supply in Baku Shipyard

Customer Keppel Singmarine Approved by James Yong Version 9


Location BAKU SHIPYARD Date 09-Oct-15

The paint specification(s) include(s) the following positions and areas


Position Area m
Flat Bottom (From bilge keel to bilge keel) 3725
Side bottom (From bilge keel to scantling draft) 2850
Sea chests 50
Anchor and Anchor chain 100
Marking on side shell, below scantling draft 20
Topside 2300
Marking above scantling draft 10
Inside of hawse pipe 1
Exposed Weather Deck 1500
Deck machinery ( crane, winches, windlass, etc), crane foundation 500
Decks underneath wooden cover 1
Mast, post, davit and pedestal on weather deck 150
Superstructure outside 3000
Deck fittings , pipe work, Radar mast, deck machinery etc 1000
Exposed exhaust pipe 100
Galvanized pipes, railings, supports, trays, etc. 500
Deck and floor of deckhouse outside 500
Wall and overhead, pipes, supports, pipes racks, ventilation ducts outside 2000
Deck and flat floor 1000
Accommodation Internal - Behind insulation 3000
Funnel inside 50
Ventilation duct inside 350
Machinery space and Thruster room (decks) 1000
Tank top and below the lowest stringer 500

Page 2 of 44
Machinery space ,stearing gear room and others store rooms (wall, overhead,) 2000
Aluminium structure 1
Water ballast tanks including outfittings & pipes 60000
Void spaces and cofferdam including Outfittings & pipes 1
Beneath suction bellmouth in W.B.tanks 1
Fresh water tanks (drinking water / potable water) 9500
Fuel Oil tanks 10000
Cooling water tanks 100
Bilge collection / waste oil / sludge tank / Sewage Tank 4500
Lube oil tanks 1
Shop Blast Primer 1
Helideck - Support Structure 1000
Helideck -Landing Pad 500
Chain Locker 200
Total 112012

Summary of products and volumes


Product Consumption (l)
ALUMINIUM PAINT H.R.,ALUMINIUM 8
BALLOXY HB LIGHT,BEIGE 23171
BALLOXY HB LIGHT,LIGHT GREEN 23171
BALTOFLAKE,BLACK 2
HARDTOP FLEXI,WHITE 78
HARDTOP FLEXI,GREEN 257 12
HARDTOP FLEXI,YELLOW 258 12
HARDTOP XP,NONE 397
HARDTOP XP,GREEN 257 529
HARDTOP XP,BLUE 138 608
HARDTOP XP,COAST WHITE 7001 1455
HARDTOP XP,WHITE 24
JOTAMASTIC 80,GREY 2987
JOTAMASTIC 80,BLACK 94
JOTAMASTIC 80,GREEN 0
JOTAMASTIC 80,ALUMINIUM RED TONED 6891
MUKI Z 2001,GREY 0
PENGUARD FC,GREEN 257 538

Page 3 of 44
PENGUARD FC,COAST WHITE 7001 632
PENGUARD PRIMER,RED 3736
PENGUARD PRIMER,GREY 25
PIONER TOPCOAT,WHITE 6
RESIST 78,GREY 15
SAFEGUARD UNIVERSAL ES,GREY 1781
SEAQUANTUM ULTRA S,LIGHT RED 3092
SEAQUANTUM ULTRA S,DARK RED 3092
SOLVALITT,BLACK 13
TANKGUARD DW,WHITE 2247
TANKGUARD DW,LIGHT GREY 2247
TANKGUARD HB,LIGHT GREY 0
TANKGUARD HB,GREYISH GREEN 0
TANKGUARD SPECIAL MIDCOAT,YELLOW 1173
TANKGUARD SPECIAL PRIMER,RED 1043
TANKGUARD SPECIAL TOPCOAT,GREY 1173
JOTUN THINNER NO. 02,CLEAR 1
JOTUN THINNER NO. 04,CLEAR 1
JOTUN THINNER NO. 07,CLEAR 311
JOTUN THINNER NO. 10,CLEAR 157
JOTUN THINNER NO. 17,CLEAR 3755
JOTUN THINNER NO. 23,CLEAR 326
STYRENE,CLEAR 0
Total 84803

Page 4 of 44
Technical specification
Project NB-Keppel Singmarine-H386-(+)-155-M-Supply/Anchor Prepared by James Yong - Jotun (Singapore) Pte. Ltd.
handling & misc..- Supply in Baku Shipyard

Customer Keppel Singmarine Approved by James Yong Version 9


Location BAKU SHIPYARD Date 09-Oct-15

Position Flat Bottom (From bilge keel to bilge keel) Area 3725 m No. 1
Surface Prep. Oil and grease etc. to be removed with a suitable detergent at all areas. The entire area to be high pressure fresh water washed at min. 250 bar in
order to remove salts and other contamination . When the surface is dry, entire surface area to be blast cleaned to min. Sa. 2.5 (ISO 8501-1:2007)
with blast profile above 50 microns
Product Type Area to Vol. solids Filmthickness (m) Loss Recoating intervals Thinner Consumption (l)
of paint % % (%) 10C 23C 40C
coat Dry spec. Wet spec. Min Max Min Max Min Max No. Max Theor. Practical
%
JOTAMASTIC 80,ALUMINIUM RED TONED FC 100 80 150 188 40 24 h 10 d 10 h 7 d 4h 5d 17 5 698 1164
SAFEGUARD UNIVERSAL ES,GREY FC 100 62 100 161 40 18 h 8 d 10 h 7 d 6h 7d 17 5 601 1001
SEAQUANTUM ULTRA S,LIGHT RED FC 100 50 140 280 40 9h * 7h * 6h * 7 5 1043 1738
SEAQUANTUM ULTRA S,DARK RED FC 100 50 140 280 40 9h * 7h * 6h * 7 5 1043 1738
Total 530

Remarks: A/F thicknesses shown for vessel trading at approx. 7... knots sailing approx. ..183. days per year (50%) for 60... months under normal trading
conditions in an average seawater temperature of approx. 28... c and assumes the existing coatings are in a sound condition. After final coat;any burnt
mark will be power tool and touch up as per spec. For Jotamastic 80 product;Wintergrade type will be used when substrate temperature reaches 15 c
and below.

Page 5 of 44
Technical specification
Project NB-Keppel Singmarine-H386-(+)-155-M-Supply/Anchor Prepared by James Yong - Jotun (Singapore) Pte. Ltd.
handling & misc..- Supply in Baku Shipyard

Customer Keppel Singmarine Approved by James Yong Version 9


Location BAKU SHIPYARD Date 09-Oct-15

Position Side bottom (From bilge keel to scantling draft) Area 2850 m No. 2
Surface Prep. Oil and grease etc. to be removed with a suitable detergent at all areas. The entire area to be high pressure fresh water washed at min. 250 bar in
order to remove salts and other contamination . When the surface is dry entire surface area to be blast cleaned to min. Sa. 2.5 (ISO 8501-1:2007)
with blast profile above 50 Microns
Product Type Area to Vol. solids Filmthickness (m) Loss Recoating intervals Thinner Consumption (l)
of paint % % (%) 10C 23C 40C
coat Dry spec. Wet spec. Min Max Min Max Min Max No. Max Theor. Practical
%
JOTAMASTIC 80,ALUMINIUM RED TONED FC 100 80 150 188 40 24 h 10 d 10 h 7 d 4 h 5 d 17 5 534 891
SAFEGUARD UNIVERSAL ES,GREY FC 100 62 100 161 40 18 h 8 d 10 h 7 d 6h 7d 17 5 460 766
SEAQUANTUM ULTRA S,LIGHT RED FC 100 50 140 280 40 9h * 7h * 6h * 7 5 798 1330
SEAQUANTUM ULTRA S,DARK RED FC 100 50 140 280 40 9h * 7h * 6h * 7 5 798 1330
Total 530

Remarks: A/F thicknesses shown for vessel trading at approx. 7... knots sailing approx. ..183. days per year (50%) for 60... months under normal trading
conditions in an average seawater temperature of approx. 28... c and assumes the existing coatings are in a sound condition. After final coat;any burnt
mark will be power tool and touch up as per spec. For Jotamastic 80 product;Wintergrade type will be used when substrate temperature reaches 15 c
and below.

Page 6 of 44
Technical specification
Project NB-Keppel Singmarine-H386-(+)-155-M-Supply/Anchor Prepared by James Yong - Jotun (Singapore) Pte. Ltd.
handling & misc..- Supply in Baku Shipyard

Customer Keppel Singmarine Approved by James Yong Version 9


Location BAKU SHIPYARD Date 09-Oct-15

Position Sea chests Area 50 m No. 3


Surface Prep. Oil and grease etc. to be removed with a suitable detergentat all areas . The entire area to be high pressure fresh water washed at min. 250 bar in
order to remove salts and other contamination . When the surface is dry entire surface area to be blast cleaned to min. Sa. 2.5 (ISO 8501-1:2007)
with blast profile above 50 microns
Product Type Area to Vol. solids Filmthickness (m) Loss Recoating intervals Thinner Consumption (l)
of paint % % (%) 10C 23C 40C
coat Dry spec. Wet spec. Min Max Min Max Min Max No. Max Theor. Practical
%
JOTAMASTIC 80,ALUMINIUM RED TONED FC 100 80 150 188 40 24 h 10 d 10 h 7 d 4 h 5 d 17 5 9 16
SAFEGUARD UNIVERSAL ES,GREY FC 100 62 100 161 40 18 h 8 d 10 h 7 d 6h 7d 17 5 8 13
SEAQUANTUM ULTRA S,LIGHT RED FC 100 50 140 280 40 9h * 7h * 6h * 7 5 14 23
SEAQUANTUM ULTRA S,DARK RED FC 100 50 140 280 40 9h * 7h * 6h * 7 5 14 23
Total 530

Remarks: After final coat;any burnt mark will be power tool and touch up as per spec. For Jotamastic 80 product;Wintergrade type will be used when substrate
temperature reaches 15 c and below.

Page 7 of 44
Technical specification
Project NB-Keppel Singmarine-H386-(+)-155-M-Supply/Anchor Prepared by James Yong - Jotun (Singapore) Pte. Ltd.
handling & misc..- Supply in Baku Shipyard

Customer Keppel Singmarine Approved by James Yong Version 9


Location BAKU SHIPYARD Date 09-Oct-15

Position Anchor and Anchor chain Area 100 m No. 4


Surface Prep. Oil and grease etc. to be removed with a suitable detergen . The entire area to be high pressure fresh water washed at min. 250 bar in order to
remove salts and other contamination. When the surface is dry entire surface area to be blast cleaned to min. Sa. 2.5 (ISO 8501-1:2007) blast
profile above 50 microns
Product Type Area to Vol. solids Filmthickness (m) Loss Recoating intervals Thinner Consumption (l)
of paint % % (%) 10C 23C 40C
coat Dry spec. Wet spec. Min Max Min Max Min Max No. Max Theor. Practical
%
JOTAMASTIC 80,BLACK FC 100 80 150 188 40 24 h * 10 h * 4h * 17 5 19 31
Total 150

Remarks: After final coat;any burnt mark will be power tool and touch up as per spec. For Jotamastic 80 product;Wintergrade type will be used when substrate
temperature reaches 15 c and below.

Page 8 of 44
Technical specification
Project NB-Keppel Singmarine-H386-(+)-155-M-Supply/Anchor Prepared by James Yong - Jotun (Singapore) Pte. Ltd.
handling & misc..- Supply in Baku Shipyard

Customer Keppel Singmarine Approved by James Yong Version 9


Location BAKU SHIPYARD Date 09-Oct-15

Position Marking on side shell, below scantling draft Area 20 m No. 5


Surface Prep.
Product Type Area to Vol. solids Filmthickness (m) Loss Recoating intervals Thinner Consumption (l)
of paint % % (%) 10C 23C 40C
coat Dry spec. Wet spec. Min Max Min Max Min Max No. Max Theor. Practical
%
PIONER TOPCOAT,WHITE FC 100 34 50 147 30 4h * 2h * 1.5 h * 7 10 3 4
Total 50

Remarks:

Page 9 of 44
Technical specification
Project NB-Keppel Singmarine-H386-(+)-155-M-Supply/Anchor Prepared by James Yong - Jotun (Singapore) Pte. Ltd.
handling & misc..- Supply in Baku Shipyard

Customer Keppel Singmarine Approved by James Yong Version 9


Location BAKU SHIPYARD Date 09-Oct-15

Position Topside Area 2300 m No. 6


Surface Prep. Oil and grease etc. to be removed with a suitable detergent.. The entire area to be high pressure fresh water washed at min. 250 bar in order to
remove salts and other contamination . When the surface is dry , entire surface area to be blast cleaned to min. Sa. 2.5 (ISO 8501-1:2007) with
blast profile above 50 microns
Product Type Area to Vol. solids Filmthickness (m) Loss Recoating intervals Thinner Consumption (l)
of paint % % (%) 10C 23C 40C
coat Dry spec. Wet spec. Min Max Min Max Min Max No. Max Theor. Practical
%
JOTAMASTIC 80,ALUMINIUM RED TONED FC 100 80 100 125 40 24 h 18 d 10 h 14 d 4 h 14 d 17 5 288 479
JOTAMASTIC 80,GREY FC 100 80 100 125 40 24 h NR 10 h NR 4h NR 17 5 288 479
HARDTOP XP,BLUE 138 FC 100 63 50 79 40 14 h * 7h * 4h * 10 5 183 304
HARDTOP XP,BLUE 138 FC 100 63 50 79 40 14 h * 7h * 4h * 10 5 183 304
Total 300

Remarks: It is recommended to finish applicaton of paints on topside before applying the antifouling on the vertical bottom. This is in order to avoid dry-spray on
the antifouling. After final coat; any burnt mark will be power tool and touch up as per spec. For Jotamastic 80 product; Wintergrade type will be used
when substrate temperature reaches 15 c and below.

Page 10 of 44
Technical specification
Project NB-Keppel Singmarine-H386-(+)-155-M-Supply/Anchor Prepared by James Yong - Jotun (Singapore) Pte. Ltd.
handling & misc..- Supply in Baku Shipyard

Customer Keppel Singmarine Approved by James Yong Version 9


Location BAKU SHIPYARD Date 09-Oct-15

Position Marking above scantling draft Area 10 m No. 7


Surface Prep.
Product Type Area to Vol. solids Filmthickness (m) Loss Recoating intervals Thinner Consumption (l)
of paint % % (%) 10C 23C 40C
coat Dry spec. Wet spec. Min Max Min Max Min Max No. Max Theor. Practical
%
PIONER TOPCOAT,WHITE FC 100 34 50 147 30 4h * 2h * 1.5 h * 7 10 1 2
Total 50

Remarks:

Page 11 of 44
Technical specification
Project NB-Keppel Singmarine-H386-(+)-155-M-Supply/Anchor Prepared by James Yong - Jotun (Singapore) Pte. Ltd.
handling & misc..- Supply in Baku Shipyard

Customer Keppel Singmarine Approved by James Yong Version 9


Location BAKU SHIPYARD Date 09-Oct-15

Position Inside of hawse pipe Area 1 m No. 8


Surface Prep. Oil and grease etc. to be removed with a suitable detergent.. The entire area to be high pressure fresh water washed at min. 250 bar in order to
remove salts and other contamination . When the surface is dry , entire surface area to be blast cleaned to min. Sa. 2.5 (ISO 8501-1:2007) with
blast profile above 50 microns
Product Type Area to Vol. solids Filmthickness (m) Loss Recoating intervals Thinner Consumption (l)
of paint % % (%) 10C 23C 40C
coat Dry spec. Wet spec. Min Max Min Max Min Max No. Max Theor. Practical
%
JOTAMASTIC 80,ALUMINIUM RED TONED FC 100 80 100 125 40 24 h * 10 h * 4h * 17 5 0 0
JOTAMASTIC 80,GREY FC 100 80 100 125 40 24 h * 10 h * 4h * 17 5 0 0
Total 200

Remarks: After final coat; any burnt mark will be power tool and touch up as per spec. For Jotamastic 80 product; Wintergrade type will be used when substrate
temperature reaches 15 c and below.

Page 12 of 44
Technical specification
Project NB-Keppel Singmarine-H386-(+)-155-M-Supply/Anchor Prepared by James Yong - Jotun (Singapore) Pte. Ltd.
handling & misc..- Supply in Baku Shipyard

Customer Keppel Singmarine Approved by James Yong Version 9


Location BAKU SHIPYARD Date 09-Oct-15

Position Exposed Weather Deck Area 1500 m No. 9


Surface Prep. Oil and grease etc. to be removed with a suitable detergent . The entire area to be high pressure fresh water washed at min. 250 bar in order to
remove salts and other contamination . When the surface is dry entire surface area to be blast cleaned to min. Sa. 2.5 (ISO 8501-1:2007) with blast
profile above 50 microns
Product Type Area to Vol. solids Filmthickness (m) Loss Recoating intervals Thinner Consumption (l)
of paint % % (%) 10C 23C 40C
coat Dry spec. Wet spec. Min Max Min Max Min Max No. Max Theor. Practical
%
JOTAMASTIC 80,ALUMINIUM RED TONED FC 100 80 125 156 40 24 h 18 d 10 h 14 d 4 h 14 d 17 5 234 391
JOTAMASTIC 80,GREY FC 100 80 125 156 40 24 h NR 10 h NR 4h NR 17 5 234 391
HARDTOP XP,GREEN 257 FC 100 63 50 79 40 14 h * 7h * 4h * 10 5 119 198
HARDTOP XP,GREEN 257 FC 100 63 50 79 40 14 h * 7h * 4h * 10 5 119 198
Total 350

Remarks: The anti Slip agregate to be applied with the 2nd coat Jotamastic 80 Grey. After final coat; any burnt mark will be power tool and touch up as per spec.
For Jotamastic 80 product; Wintergrade type will be used when substrate temperature reaches 15 c and below.

Page 13 of 44
Technical specification
Project NB-Keppel Singmarine-H386-(+)-155-M-Supply/Anchor Prepared by James Yong - Jotun (Singapore) Pte. Ltd.
handling & misc..- Supply in Baku Shipyard

Customer Keppel Singmarine Approved by James Yong Version 9


Location BAKU SHIPYARD Date 09-Oct-15

Position Deck machinery ( crane, winches, windlass, etc), crane foundation Area 500 m No. 10
Surface Prep. Oil and grease etc. to be removed with a suitable detergent . The entire area to be high pressure fresh water washed at min. 250 bar in order to
remove salts and other contamination. When the surface is dry entire surface area to be blast cleaned to min Sa 2.5 (ISO 8501-1:2007) with blast
profile above 50 microns
Product Type Area to Vol. solids Filmthickness (m) Loss Recoating intervals Thinner Consumption (l)
of paint % % (%) 10C 23C 40C
coat Dry spec. Wet spec. Min Max Min Max Min Max No. Max Theor. Practical
%
JOTAMASTIC 80,ALUMINIUM RED TONED FC 100 80 125 156 40 24 h 18 d 10 h 14 d 4 h 14 d 17 5 78 130
JOTAMASTIC 80,GREY FC 100 80 125 156 40 24 h NR 10 h NR 4h NR 17 5 78 130
HARDTOP XP,NONE FC 100 63 50 79 40 14 h * 7h * 4h * 10 5 40 66
HARDTOP XP,NONE FC 100 63 50 79 40 14 h * 7h * 4h * 10 5 40 66
Total 350

Remarks: Topcoat colour shall follow maker shade

Page 14 of 44
Technical specification
Project NB-Keppel Singmarine-H386-(+)-155-M-Supply/Anchor Prepared by James Yong - Jotun (Singapore) Pte. Ltd.
handling & misc..- Supply in Baku Shipyard

Customer Keppel Singmarine Approved by James Yong Version 9


Location BAKU SHIPYARD Date 09-Oct-15

Position Decks underneath wooden cover Area 1 m No. 11


Surface Prep. Oil and grease etc. to be removed with a suitable detergent . The entire area to be high pressure fresh water washed at min. 250 bar in order to
remove salts and other contamination . When the surface is dry w, entire surface area to be blast cleaned to min. Sa. 2.5 (ISO 8501-1:2007) with
blast profile above 50 microns
Product Type Area to Vol. solids Filmthickness (m) Loss Recoating intervals Thinner Consumption (l)
of paint % % (%) 10C 23C 40C
coat Dry spec. Wet spec. Min Max Min Max Min Max No. Max Theor. Practical
%
JOTAMASTIC 80,ALUMINIUM RED TONED FC 100 80 100 125 40 24 h 18 d 10 h 14 d 4 h 14 d 17 5 0 0
JOTAMASTIC 80,GREEN FC 100 80 100 125 40 24 h * 10 h * 4h * 17 5 0 0
Total 200

Remarks: After final coat;any burnt mark will be power tool and touch up as per spec. For Jotamastic 80 product;Wintergrade type will be used when substrate
temperature reaches 15 c and below.

Page 15 of 44
Technical specification
Project NB-Keppel Singmarine-H386-(+)-155-M-Supply/Anchor Prepared by James Yong - Jotun (Singapore) Pte. Ltd.
handling & misc..- Supply in Baku Shipyard

Customer Keppel Singmarine Approved by James Yong Version 9


Location BAKU SHIPYARD Date 09-Oct-15

Position Mast, post, davit and pedestal on weather deck Area 150 m No. 12
Surface Prep. Surfaces shall be prepared by mechanical preparation methods to ISO 8501-1 St 3 to ensure the surface is correctly prepared by removing loose
residual corrosion, failed coatings and other contamination so that what remains is intact and well adhered to the surface.
Product Type Area to Vol. solids Filmthickness (m) Loss Recoating intervals Thinner Consumption (l)
of paint % % (%) 10C 23C 40C
coat Dry spec. Wet spec. Min Max Min Max Min Max No. Max Theor. Practical
%
PENGUARD PRIMER,GREY FC 100 51 50 98 40 8 h 7 d 4 h 7 d 3 h 5 d 17 10 15 25
HARDTOP XP,WHITE FC 100 63 60 95 40 14 h * 7h * 4h * 10 10 14 24
Total 110

Remarks: After final coat; any burnt mark will be power tool and touch up as per spec. For Jotamastic 80 product; Wintergrade type will be used when substrate
temperature reaches 15 c and below.

Page 16 of 44
Technical specification
Project NB-Keppel Singmarine-H386-(+)-155-M-Supply/Anchor Prepared by James Yong - Jotun (Singapore) Pte. Ltd.
handling & misc..- Supply in Baku Shipyard

Customer Keppel Singmarine Approved by James Yong Version 9


Location BAKU SHIPYARD Date 09-Oct-15

Position Superstructure outside Area 3000 m No. 13


Surface Prep. Oil and grease etc. to be removed with a suitable detergent . The entire area to be high pressure fresh water washed at min. 250 bar in order to
remove salts and other contamination .When the surface is dry entire surface area to be blast cleaned to min SA 2.5 (ISO 8501-1:2007) with blast
profile above 50 microns.
Product Type Area to Vol. solids Filmthickness (m) Loss Recoating intervals Thinner Consumption (l)
of paint % % (%) 10C 23C 40C
coat Dry spec. Wet spec. Min Max Min Max Min Max No. Max Theor. Practical
%
JOTAMASTIC 80,ALUMINIUM RED TONED FC 100 80 100 125 40 24 h 18 d 10 h 14 d 4 h 14 d 17 5 375 625
JOTAMASTIC 80,GREY FC 100 80 100 125 40 24 h NR 10 h NR 4h NR 17 5 375 625
HARDTOP XP,COAST WHITE 7001 FC 100 63 50 79 40 14 h * 7h * 4h * 10 5 238 397
HARDTOP XP,COAST WHITE 7001 FC 100 63 50 79 40 14 h * 7h * 4h * 10 5 238 397
Total 300

Remarks: After final coat;any burnt mark will be power tool and touch up as per spec. For Jotamastic 80 product;Wintergrade type will be used when substrate
temperature reaches 15 c and below.

Page 17 of 44
Technical specification
Project NB-Keppel Singmarine-H386-(+)-155-M-Supply/Anchor Prepared by James Yong - Jotun (Singapore) Pte. Ltd.
handling & misc..- Supply in Baku Shipyard

Customer Keppel Singmarine Approved by James Yong Version 9


Location BAKU SHIPYARD Date 09-Oct-15

Position Deck fittings , pipe work, Radar mast, deck machinery etc Area 1000 m No. 14
Surface Prep. Oil and grease etc. to be removed with a suitable detergent . The entire area to be high pressure fresh water washed at min. 250 bar in order to
remove salts and other contamination . When the surface is dry , entire surface area to be blast cleaned to min. SA 2.5 (ISO 8501-1:2007) with
blast profile above 50 microns
Product Type Area to Vol. solids Filmthickness (m) Loss Recoating intervals Thinner Consumption (l)
of paint % % (%) 10C 23C 40C
coat Dry spec. Wet spec. Min Max Min Max Min Max No. Max Theor. Practical
%
JOTAMASTIC 80,ALUMINIUM RED TONED FC 100 80 100 125 40 24 h 18 d 10 h 14 d 4 h 14 d 17 5 125 208
JOTAMASTIC 80,GREY FC 100 80 100 125 40 24 h NR 10 h NR 4h NR 17 5 125 208
HARDTOP XP,NONE FC 100 63 50 79 40 14 h * 7h * 4h * 10 5 79 132
HARDTOP XP,NONE FC 100 63 50 79 40 14 h * 7h * 4h * 10 5 79 132
Total 300

Remarks: Topcoat will follow maker shade. After final coat;any burnt mark will be power tool and touch up as per spec. For Jotamastic 80 product;Wintergrade
type will be used when substrate temperature reaches 15 c and below.

Page 18 of 44
Technical specification
Project NB-Keppel Singmarine-H386-(+)-155-M-Supply/Anchor Prepared by James Yong - Jotun (Singapore) Pte. Ltd.
handling & misc..- Supply in Baku Shipyard

Customer Keppel Singmarine Approved by James Yong Version 9


Location BAKU SHIPYARD Date 09-Oct-15

Position Exposed exhaust pipe Area 100 m No. 15


Surface Prep. Oil and grease etc. to be removed with a suitable detergent . The entire area to be high pressure fresh water washed at min. 250 bar in order to
remove salts and other contamination if require. When the surface is dry the entire surface area is to be blast cleaned to min. Sa. 2.5 (ISO 8501-
1:2007) with blast profile above 50 Microns.
Product Type Area to Vol. solids Filmthickness (m) Loss Recoating intervals Thinner Consumption (l)
of paint % % (%) 10C 23C 40C
coat Dry spec. Wet spec. Min Max Min Max Min Max No. Max Theor. Practical
%
RESIST 78,GREY FC 100 72 75 104 30 13 h NR 4 h NR 1.5 h NR 4 10 10 15
SOLVALITT,BLACK FC 100 43 20 47 30 5h NR 4h NR 3h NR 7 10 5 7
SOLVALITT,BLACK FC 100 43 20 47 30 5h * 4h * 3h * 7 10 5 7
Total 115

Remarks: After final coat;any burnt mark will be power tool and touch up as per spec.

Page 19 of 44
Technical specification
Project NB-Keppel Singmarine-H386-(+)-155-M-Supply/Anchor Prepared by James Yong - Jotun (Singapore) Pte. Ltd.
handling & misc..- Supply in Baku Shipyard

Customer Keppel Singmarine Approved by James Yong Version 9


Location BAKU SHIPYARD Date 09-Oct-15

Position Galvanized pipes, railings, supports, trays, etc. Area 500 m No. 16
Surface Prep. Oil and grease etc. to be removed with a suitable detergent . The entire area to be high pressure fresh water cleaned at min. 250 bar in order to
remove salts and other contamination . To sand paper if require surface roughness.
Product Type Area to Vol. solids Filmthickness (m) Loss Recoating intervals Thinner Consumption (l)
of paint % % (%) 10C 23C 40C
coat Dry spec. Wet spec. Min Max Min Max Min Max No. Max Theor. Practical
%
PENGUARD PRIMER,RED FC 100 51 50 98 30 8h * 4h * 3h * 17 10 49 70
Comment: Subsequent coat to follow surrounding coating system * * * * * *
Total 50

Remarks: Damage to galvanizing will be power tool to ST2 and repaired using Jotun Barrier 80 grey at 85 microns. After final coat;any burnt mark will be power
tool and touch up as per spec.

Page 20 of 44
Technical specification
Project NB-Keppel Singmarine-H386-(+)-155-M-Supply/Anchor Prepared by James Yong - Jotun (Singapore) Pte. Ltd.
handling & misc..- Supply in Baku Shipyard

Customer Keppel Singmarine Approved by James Yong Version 9


Location BAKU SHIPYARD Date 09-Oct-15

Position Deck and floor of deckhouse outside Area 500 m No. 17


Surface Prep. Oil and grease etc. to be removed with a suitable detergent . The entire area to be high pressure fresh water washed at min. 250 bar in order to
remove salts and other contamination . When surface is dry , entire surface area to be blast cleaned to min SA 2.5 (ISO 8501-1:2007) with blast
profile above 50 microns
Product Type Area to Vol. solids Filmthickness (m) Loss Recoating intervals Thinner Consumption (l)
of paint % % (%) 10C 23C 40C
coat Dry spec. Wet spec. Min Max Min Max Min Max No. Max Theor. Practical
%
JOTAMASTIC 80,ALUMINIUM RED TONED FC 100 80 125 156 40 24 h 18 d 10 h 14 d 4 h 14 d 17 5 78 130
JOTAMASTIC 80,GREY FC 100 80 125 156 40 24 h NR 10 h NR 4h NR 17 5 78 130
HARDTOP XP,GREEN 257 FC 100 63 50 79 40 14 h * 7h * 4h * 10 5 40 66
HARDTOP XP,GREEN 257 FC 100 63 50 79 40 14 h * 7h * 4h * 10 5 40 66
Total 350

Remarks: Anti Slip agregate to be applied with the 2nd coat Jotamastic 80 Grey. After final coat;any burnt mark will be power tool and touch up as per spec. For
Jotamastic 80 product;Wintergrade type will be used when substrate temperature reaches 15 c and below.

Page 21 of 44
Technical specification
Project NB-Keppel Singmarine-H386-(+)-155-M-Supply/Anchor Prepared by James Yong - Jotun (Singapore) Pte. Ltd.
handling & misc..- Supply in Baku Shipyard

Customer Keppel Singmarine Approved by James Yong Version 9


Location BAKU SHIPYARD Date 09-Oct-15

Position Wall and overhead, pipes, supports, pipes racks, ventilation ducts outside Area 2000 m No. 18
Surface Prep. Oil and grease etc. to be removed with a suitable detergent . The entire area to be high pressure fresh water washed at min. 250 bar in order to
remove salts and other contamination . When the surface is dry, entire surface area to be blast cleaned to min. Sa. 2.5 (ISO 8501-1:2007) with
blast profile above 50 microns
Product Type Area to Vol. solids Filmthickness (m) Loss Recoating intervals Thinner Consumption (l)
of paint % % (%) 10C 23C 40C
coat Dry spec. Wet spec. Min Max Min Max Min Max No. Max Theor. Practical
%
JOTAMASTIC 80,ALUMINIUM RED TONED FC 100 80 125 156 40 24 h 18 d 10 h 14 d 4 h 14 d 17 5 313 521
JOTAMASTIC 80,GREY FC 100 80 125 156 40 24 h NR 10 h NR 4h NR 17 5 313 521
HARDTOP XP,COAST WHITE 7001 FC 100 63 50 79 40 14 h * 7h * 4h * 10 5 159 265
HARDTOP XP,COAST WHITE 7001 FC 100 63 50 79 40 14 h * 7h * 4h * 10 5 159 265
Total 350

Remarks: Other items Topcoat colour will be in accordance to surrounding Topcoat colours. After final coat;any burnt mark will be power tool and touch up as per
spec. For Jotamastic 80 product;Wintergrade type will be used when substrate temperature reaches 15 c and below.

Page 22 of 44
Technical specification
Project NB-Keppel Singmarine-H386-(+)-155-M-Supply/Anchor Prepared by James Yong - Jotun (Singapore) Pte. Ltd.
handling & misc..- Supply in Baku Shipyard

Customer Keppel Singmarine Approved by James Yong Version 9


Location BAKU SHIPYARD Date 09-Oct-15

Position Deck and flat floor Area 1000 m No. 19


Surface Prep. Oil and grease etc. to be removed with a suitable detergent . The entire area to be high pressure fresh water washed at min. 250 bar in order to
remove salts and other contamination. When the surface is dry, entire surface area to be blast cleaned to min SA. 2.5 (ISO 8501-1:2007) with blast
profile above 50 microns.
Product Type Area to Vol. solids Filmthickness (m) Loss Recoating intervals Thinner Consumption (l)
of paint % % (%) 10C 23C 40C
coat Dry spec. Wet spec. Min Max Min Max Min Max No. Max Theor. Practical
%
JOTAMASTIC 80,ALUMINIUM RED TONED FC 100 80 100 125 40 24 h 18 d 10 h 14 d 4 h 14 d 17 5 125 208
PENGUARD FC,GREEN 257 FC 100 62 100 161 40 15 h * 7.5 h * 4h * 17 10 161 269
Total 200

Remarks: After final coat;any burnt mark will be power tool and touch up as per spec. For Jotamastic 80 product;Wintergrade type will be used when substrate
temperature reaches 15 c and below.

Page 23 of 44
Technical specification
Project NB-Keppel Singmarine-H386-(+)-155-M-Supply/Anchor Prepared by James Yong - Jotun (Singapore) Pte. Ltd.
handling & misc..- Supply in Baku Shipyard

Customer Keppel Singmarine Approved by James Yong Version 9


Location BAKU SHIPYARD Date 09-Oct-15

Position Accommodation Internal - Behind insulation Area 3000 m No. 20


Surface Prep. Oil and grease etc. to be removed with a suitable detergent . The entire area to be high pressure fresh water washed at min. 250 bar in order to
remove salts and other contamination . When the surface is dry , entire surface area to be blast cleaned to min SA 2.5 (ISO 8501-1:2007) with
blast profile above 50 microns.
Product Type Area to Vol. solids Filmthickness (m) Loss Recoating intervals Thinner Consumption (l)
of paint % % (%) 10C 23C 40C
coat Dry spec. Wet spec. Min Max Min Max Min Max No. Max Theor. Practical
%
JOTAMASTIC 80,ALUMINIUM RED TONED FC 100 80 100 125 40 24 h * 10 h * 4h * 17 5 375 625
Total 100

Remarks: After final coat;any burnt mark will be power tool and touch up as per spec. For Jotamastic 80 product;Wintergrade type will be used when substrate
temperature reaches 15 c and below.

Page 24 of 44
Technical specification
Project NB-Keppel Singmarine-H386-(+)-155-M-Supply/Anchor Prepared by James Yong - Jotun (Singapore) Pte. Ltd.
handling & misc..- Supply in Baku Shipyard

Customer Keppel Singmarine Approved by James Yong Version 9


Location BAKU SHIPYARD Date 09-Oct-15

Position Funnel inside Area 50 m No. 21


Surface Prep. Oil and grease etc. to be removed with a suitable detergent all areas. The entire area to be high pressure fresh water washed at min 250 bar in
order to remove salts and other contamination. When the surface is dry entire surface area to be blast cleaned to min SA 2.5 (ISO 8501-1:2007)
with blast profile above 50 microns.
Product Type Area to Vol. solids Filmthickness (m) Loss Recoating intervals Thinner Consumption (l)
of paint % % (%) 10C 23C 40C
coat Dry spec. Wet spec. Min Max Min Max Min Max No. Max Theor. Practical
%
ALUMINIUM PAINT H.R.,ALUMINIUM FC 100 45 25 56 30 12 h * 8h * 6h * 2 10 3 4
ALUMINIUM PAINT H.R.,ALUMINIUM FC 100 45 25 56 30 12 h * 8h * 6h * 2 10 3 4
Total 50

Remarks:

Page 25 of 44
Technical specification
Project NB-Keppel Singmarine-H386-(+)-155-M-Supply/Anchor Prepared by James Yong - Jotun (Singapore) Pte. Ltd.
handling & misc..- Supply in Baku Shipyard

Customer Keppel Singmarine Approved by James Yong Version 9


Location BAKU SHIPYARD Date 09-Oct-15

Position Ventilation duct inside Area 350 m No. 22


Surface Prep. Surfaces shall be prepared by mechanical preparation methods to ISO 8501-1 St 3 to ensure the surface is correctly prepared by removing loose
residual corrosion, failed coatings and other contamination so that what remains is intact and well adhered to the surface.
Product Type Area to Vol. solids Filmthickness (m) Loss Recoating intervals Thinner Consumption (l)
of paint % % (%) 10C 23C 40C
coat Dry spec. Wet spec. Min Max Min Max Min Max No. Max Theor. Practical
%
PENGUARD PRIMER,RED FC 100 51 50 98 40 8 h 9 mth 4 h 9 mth 3 h 9 mth 17 10 34 57
PENGUARD FC,COAST WHITE 7001 FC 100 62 100 161 40 15 h * 7.5 h * 4h * 17 10 56 94
Total 150

Remarks: After final coat;any burnt mark will be power tool and touch up as per spec. For Jotamastic 80 product;Wintergrade type will be used when substrate
temperature reaches 15 c and below.

Page 26 of 44
Technical specification
Project NB-Keppel Singmarine-H386-(+)-155-M-Supply/Anchor Prepared by James Yong - Jotun (Singapore) Pte. Ltd.
handling & misc..- Supply in Baku Shipyard

Customer Keppel Singmarine Approved by James Yong Version 9


Location BAKU SHIPYARD Date 09-Oct-15

Position Machinery space and Thruster room (decks) Area 1000 m No. 23
Surface Prep. Oil and grease etc. to be removed with a suitable detergent . The entire area to be high pressure fresh water washed at min. 250 bar in order to
remove salts and other contamination . When the surface is dry, entire surface area to be blast cleaned to min SA 2.5 (ISO 8501-1:2007) with blast
profile above 50 microns
Product Type Area to Vol. solids Filmthickness (m) Loss Recoating intervals Thinner Consumption (l)
of paint % % (%) 10C 23C 40C
coat Dry spec. Wet spec. Min Max Min Max Min Max No. Max Theor. Practical
%
JOTAMASTIC 80,ALUMINIUM RED TONED FC 100 80 150 188 40 24 h 18 d 10 h 14 d 4 h 14 d 17 5 188 313
PENGUARD FC,GREEN 257 FC 100 62 100 161 40 15 h * 7.5 h * 4h * 17 10 161 269
Total 250

Remarks: After final coat;any burnt mark will be power tool and touch up as per spec. For Jotamastic 80 product;Wintergrade type will be used when substrate
temperature reaches 15 c and below.

Page 27 of 44
Technical specification
Project NB-Keppel Singmarine-H386-(+)-155-M-Supply/Anchor Prepared by James Yong - Jotun (Singapore) Pte. Ltd.
handling & misc..- Supply in Baku Shipyard

Customer Keppel Singmarine Approved by James Yong Version 9


Location BAKU SHIPYARD Date 09-Oct-15

Position Tank top and below the lowest stringer Area 500 m No. 24
Surface Prep. Oil and grease etc. to be removed with a suitable detergent . The entire area to be high pressure fresh water washed at min. 250 bar in order to
remove salts and other contamination .When the surface is dry, entire surface area to be blast cleaned to min SA 2.5 (ISO 8501-1:2007) with blast
profile above 50 microns
Product Type Area to Vol. solids Filmthickness (m) Loss Recoating intervals Thinner Consumption (l)
of paint % % (%) 10C 23C 40C
coat Dry spec. Wet spec. Min Max Min Max Min Max No. Max Theor. Practical
%
JOTAMASTIC 80,ALUMINIUM RED TONED FC 100 80 125 156 30 24 h 18 d 10 h 14 d 4 h 14 d 17 10 78 112
JOTAMASTIC 80,GREY FC 100 80 125 156 30 24 h * 10 h * 4h * 17 10 78 112
Total 250

Remarks: After final coat;any burnt mark will be power tool and touch up as per spec. For Jotamastic 80 product;Wintergrade type will be used when substrate
temperature reaches 15 c and below.

Page 28 of 44
Technical specification
Project NB-Keppel Singmarine-H386-(+)-155-M-Supply/Anchor Prepared by James Yong - Jotun (Singapore) Pte. Ltd.
handling & misc..- Supply in Baku Shipyard

Customer Keppel Singmarine Approved by James Yong Version 9


Location BAKU SHIPYARD Date 09-Oct-15

Position Machinery space ,stearing gear room and others store rooms (wall, overhead,) Area 2000 m No. 25
Surface Prep. Oil and greaseetc to be removed with suitable detergent all areas. The entire area to be high pressure fresh water washed atmin 250 bar in order to
remove salts and other contamination. When surface is dry , entire surface area to be blast cleaned to min SA 2.5 (ISO 8501-1:2007 ) with blast
profile above 50 microns
Product Type Area to Vol. solids Filmthickness (m) Loss Recoating intervals Thinner Consumption (l)
of paint % % (%) 10C 23C 40C
coat Dry spec. Wet spec. Min Max Min Max Min Max No. Max Theor. Practical
%
JOTAMASTIC 80,ALUMINIUM RED TONED FC 100 80 150 188 40 24 h 18 d 10 h 14 d 4 h 14 d 17 5 375 625
PENGUARD FC,COAST WHITE 7001 FC 100 62 100 161 40 15 h * 7.5 h * 4h * 17 10 323 538
Total 250

Remarks:

Page 29 of 44
Technical specification
Project NB-Keppel Singmarine-H386-(+)-155-M-Supply/Anchor Prepared by James Yong - Jotun (Singapore) Pte. Ltd.
handling & misc..- Supply in Baku Shipyard

Customer Keppel Singmarine Approved by James Yong Version 9


Location BAKU SHIPYARD Date 09-Oct-15

Position Aluminium structure Area 1 m No. 26


Surface Prep. After pre-treatment of welds, sharp edges, removal of weld spatter and other surface contamination the surface shall be degreased using an
alkaline detergent, and cleaned by low-pressure Water Cleaning LP WC method to ISO 8501-4 Wa 1 with fresh water and then hand or machine
abraded with non-metallic abrasives or bonded fibre machine or hand abrasive pads to remove all polish and to impart a scratch pattern to the
surface. Do not use high speed rotational sanders.
Product Type Area to Vol. solids Filmthickness (m) Loss Recoating intervals Thinner Consumption (l)
of paint % % (%) 10C 23C 40C
coat Dry spec. Wet spec. Min Max Min Max Min Max No. Max Theor. Practical
%
PENGUARD PRIMER,RED FC 100 51 50 98 30 8h * 4h * 3h * 17 10 0 0
Comment: Subsequent coat follow the surrounding color & thickness * * * * * *
Total 50

Remarks: After final coat; any burnt mark will be power tool and touch up as per spec. For Jotamastic 80 product; Wintergrade type will be used when substrate
temperature reaches 15 c and below.

Page 30 of 44
Technical specification
Project NB-Keppel Singmarine-H386-(+)-155-M-Supply/Anchor Prepared by James Yong - Jotun (Singapore) Pte. Ltd.
handling & misc..- Supply in Baku Shipyard

Customer Keppel Singmarine Approved by James Yong Version 9


Location BAKU SHIPYARD Date 09-Oct-15

Position Water ballast tanks including outfittings & pipes Area 60000 m No. 27
Surface Prep. Oil and grease etc. to be removed with a suitable detergent . The entire area to be high pressure fresh water washed at min. 250 bar in order to
remove salts and other contamination . When the surface is dry entire surface area to be blast cleaned to min. Sa. 2.5 (ISO 8501-1:2007) with blast
profile above 50 microns
Product Type Area to Vol. solids Filmthickness (m) Loss Recoating intervals Thinner Consumption (l)
of paint % % (%) 10C 23C 40C
coat Dry spec. Wet spec. Min Max Min Max Min Max No. Max Theor. Practical
%
BALLOXY HB LIGHT,LIGHT GREEN FC 100 82 175 213 40 24 h 3 mth 10 h 3 mth 4 h 2 mth 17 5 12805 21341
BALLOXY HB LIGHT,BEIGE SC 20 82 100 122 20 24 h 3 mth 10 h 3 mth 4 h 2 mth 17 5 1463 1829
BALLOXY HB LIGHT,LIGHT GREEN SC 20 82 100 122 20 24 h 3 mth 10 h 3 mth 4 h 2 mth 17 5 1463 1829
BALLOXY HB LIGHT,BEIGE FC 100 82 175 213 40 24 h * 10 h * 4h * 17 5 12805 21341
Total 350

Page 31 of 44
Remarks: Note:
1. Ambient condition during surface pretreatment and coatings application:
a. the relative humidity has to be lower than 85%.
b. the surface temperature of substrate must be 3C higher than dew point in adjacent area.
2. In case of full or partial blasting;the profile shall be 30-75 um;otherwise as recommend by Jotun.
3. The surface shall be free from oil/grease and other contamination before paint application.
4. Dust quantity rating "1" for dust size class "3";"4" or "5" according to ISO 8502-3. Lower dust size classes to be removed if visible on the surface to be
coated without magnification.
5. Shop primer should be zinc containing inhibitor free zinc silicate based or equivalent. Jotun shall confirm compatibility with main coating system and
the shopprimer. Otherwise;abrasive blasting to Sa 2 according to ISO 8501-1:1988 has to be carried out to remove at least 70% of intact shop primer.
6. Water soluble salt testing according to ISO 8502-9 has to be carried out after primary and secondary surface preparation. The limit equivalent to
sodium chloride (NaCl) must less or equal to 50 mg/m2.
7. Surface treatment after erection: Small damages up to 2% of total areas: St 3. Contiguous damages over 25 m2 or over 2% of the total area of the
tank: Sa 2 1/2.
8. "90% of all thickness measurements should be greater than or equal to NDFT (nominal dry film thickness) and none of the remaining 10%
measurements should be below 0.9xNDFT".
9. The maximum DFT shall not exceed to 300 um of single coat and total DFT of system shall not over 800um in accordence to product
recommendation. Otherwise it need to be sand down

Page 32 of 44
Technical specification
Project NB-Keppel Singmarine-H386-(+)-155-M-Supply/Anchor Prepared by James Yong - Jotun (Singapore) Pte. Ltd.
handling & misc..- Supply in Baku Shipyard

Customer Keppel Singmarine Approved by James Yong Version 9


Location BAKU SHIPYARD Date 09-Oct-15

Position Void spaces and cofferdam including Outfittings & pipes Area 1 m No. 28
Surface Prep. Oil and grease etc. to be removed with a suitable detergent . The entire area to be high pressure fresh water washed at min. 250 bar in order to
remove salts and other contamination . When the surface is dry , entire surface area to be blast cleaned to min. Sa. 2.5 (ISO 8501-1:2007) with
blast profile above 50 microns
Product Type Area to Vol. solids Filmthickness (m) Loss Recoating intervals Thinner Consumption (l)
of paint % % (%) 10C 23C 40C
coat Dry spec. Wet spec. Min Max Min Max Min Max No. Max Theor. Practical
%
JOTAMASTIC 80,ALUMINIUM RED TONED FC 100 80 125 156 30 24 h 18 d 10 h 14 d 4 h 14 d 17 10 0 0
JOTAMASTIC 80,GREY FC 100 80 125 156 30 24 h * 10 h * 4h * 17 10 0 0
Total 250

Remarks: After final coat;any burnt mark will be power tool and touch up as per spec. For Jotamastic 80 product;Wintergrade type will be used when substrate
temperature reaches 15 c and below.

Page 33 of 44
Technical specification
Project NB-Keppel Singmarine-H386-(+)-155-M-Supply/Anchor Prepared by James Yong - Jotun (Singapore) Pte. Ltd.
handling & misc..- Supply in Baku Shipyard

Customer Keppel Singmarine Approved by James Yong Version 9


Location BAKU SHIPYARD Date 09-Oct-15

Position Beneath suction bellmouth in W.B.tanks Area 1 m No. 29


Surface Prep. Oil and grease etc. to be removed with a suitable detergent . The entire area to be high pressure fresh water washed at min. 250 bar in order to
remove salts and other contamination . When the surface is dry the entire surface area is to be blast cleaned to min. Sa. 2.5 (ISO 8501-1:2007)
with blast profile above 50 microns.
Product Type Area to Vol. solids Filmthickness (m) Loss Recoating intervals Thinner Consumption (l)
of paint % % (%) 10C 23C 40C
coat Dry spec. Wet spec. Min Max Min Max Min Max No. Max Theor. Practical
%
BALTOFLAKE,BLACK FC 100 96 1000 1042 40 5h * 2h * 2h * S 5 1 2
Total 1000

Remarks:

Page 34 of 44
Technical specification
Project NB-Keppel Singmarine-H386-(+)-155-M-Supply/Anchor Prepared by James Yong - Jotun (Singapore) Pte. Ltd.
handling & misc..- Supply in Baku Shipyard

Customer Keppel Singmarine Approved by James Yong Version 9


Location BAKU SHIPYARD Date 09-Oct-15

Position Fresh water tanks (drinking water / potable water) Area 9500 m No. 30
Surface Prep. Oil and grease etc. to be removed with a suitable detergent . The entire area to be high pressure fresh water washed at min. 250 bar in order to
remove salts and other contamination. When the surface is dry the entire surface area is to be blast cleaned to min. Sa. 2.5 (ISO 8501-1:2007) with
blast profile above 50 mcrons.
Product Type Area to Vol. solids Filmthickness (m) Loss Recoating intervals Thinner Consumption (l)
of paint % % (%) 10C 23C 40C
coat Dry spec. Wet spec. Min Max Min Max Min Max No. Max Theor. Practical
%
PENGUARD PRIMER,RED FC 100 51 50 98 30 8 h 9 mth 4 h 9 mth 3 h 9 mth 17 10 931 1331
TANKGUARD DW,LIGHT GREY FC 100 100 150 150 30 25 h 10 d 13 h 5 d 5h 3d 17 10 1425 2036
TANKGUARD DW,WHITE SC 20 100 100 100 10 25 h 10 d 13 h 5 d 5h 3d 17 5 190 211
TANKGUARD DW,LIGHT GREY SC 20 100 100 100 10 25 h 10 d 13 h 5 d 5h 3d 17 5 190 211
TANKGUARD DW,WHITE FC 100 100 150 150 30 25 h * 13 h * 5h * 17 10 1425 2036
Total 350

Remarks: Upon application of 1st coat Penguard Primer. Please allow proper curing for 2 weeks before application of subsequent system.
Stripe coat recommended for free edges ;plating stifferners;weld seams and other difficult to reach / spray areas

Page 35 of 44
Technical specification
Project NB-Keppel Singmarine-H386-(+)-155-M-Supply/Anchor Prepared by James Yong - Jotun (Singapore) Pte. Ltd.
handling & misc..- Supply in Baku Shipyard

Customer Keppel Singmarine Approved by James Yong Version 9


Location BAKU SHIPYARD Date 09-Oct-15

Position Fuel Oil tanks Area 10000 m No. 31


Surface Prep. Oil and grease etc. to be removed with a suitable detergent . The entire area to be high pressure fresh water washed at min. 250 bar in order to
remove salts and other contamination . When the surface is dry, entire surface area to be blast cleaned to min. Sa. 2.5 (ISO 8501-1:2007) with
blast profile above 50 microns.
Product Type Area to Vol. solids Filmthickness (m) Loss Recoating intervals Thinner Consumption (l)
of paint % % (%) 10C 23C 40C
coat Dry spec. Wet spec. Min Max Min Max Min Max No. Max Theor. Practical
%
PENGUARD PRIMER,RED FC 100 51 50 98 40 8h * 4h * 3h * 17 5 980 1634
Total 50

Remarks:

Page 36 of 44
Technical specification
Project NB-Keppel Singmarine-H386-(+)-155-M-Supply/Anchor Prepared by James Yong - Jotun (Singapore) Pte. Ltd.
handling & misc..- Supply in Baku Shipyard

Customer Keppel Singmarine Approved by James Yong Version 9


Location BAKU SHIPYARD Date 09-Oct-15

Position Cooling water tanks Area 100 m No. 32


Surface Prep. Oil and grease etc. to be removed with a suitable detergent . The entire area to be high pressure fresh water washed at min. 250 bar in order to
remove salts and other contamination . When the surface is dry, entire surface area to be blast cleaned to min. Sa. 2.5 (ISO 8501-1:2007) with
blast profile above 50 microns.
Product Type Area to Vol. solids Filmthickness (m) Loss Recoating intervals Thinner Consumption (l)
of paint % % (%) 10C 23C 40C
coat Dry spec. Wet spec. Min Max Min Max Min Max No. Max Theor. Practical
%
PENGUARD PRIMER,RED FC 100 51 50 98 30 8 h NR 4 h NR 3 h NR 17 10 10 14
TANKGUARD SPECIAL PRIMER,RED FC 100 63 100 159 30 52 h 18 d 20 h 7 d 10 h 4 d 23 10 16 23
TANKGUARD SPECIAL MIDCOAT,YELLOW SC 20 63 80 127 10 52 h 18 d 20 h 7 d 10 h 4 d 23 5 3 3
TANKGUARD SPECIAL MIDCOAT,YELLOW FC 100 63 100 159 30 52 h 18 d 20 h 7 d 10 h 4 d 23 10 16 23
TANKGUARD SPECIAL TOPCOAT,GREY SC 20 63 80 127 20 52 h 18 d 20 h 7 d 10 h 4 d 23 5 3 3
TANKGUARD SPECIAL TOPCOAT,GREY FC 100 63 100 159 30 52 h * 20 h * 10 h * 23 10 16 23
Total 350

Remarks:

Page 37 of 44
Technical specification
Project NB-Keppel Singmarine-H386-(+)-155-M-Supply/Anchor Prepared by James Yong - Jotun (Singapore) Pte. Ltd.
handling & misc..- Supply in Baku Shipyard

Customer Keppel Singmarine Approved by James Yong Version 9


Location BAKU SHIPYARD Date 09-Oct-15

Position Bilge collection / waste oil / sludge tank / Sewage Tank Area 4500 m No. 33
Surface Prep. Oil and grease etc. to be removed with a suitable detergent . The entire area to be high pressure fresh water washed at min. 250 bar in order to
remove salts and other contamination. When the surface is dry , entire surface area to be blast cleaned to min. Sa. 2.5 (ISO 8501-1:2007) with
blast profile above 50 microns.
Product Type Area to Vol. solids Filmthickness (m) Loss Recoating intervals Thinner Consumption (l)
of paint % % (%) 10C 23C 40C
coat Dry spec. Wet spec. Min Max Min Max Min Max No. Max Theor. Practical
%
PENGUARD PRIMER,RED FC 100 51 50 98 30 8 h NR 4 h NR 3 h NR 17 10 441 630
TANKGUARD SPECIAL PRIMER,RED FC 100 63 100 159 30 52 h 18 d 20 h 7 d 10 h 4 d 23 10 714 1020
TANKGUARD SPECIAL MIDCOAT,YELLOW SC 20 63 80 127 10 52 h 18 d 20 h 7 d 10 h 4 d 23 5 114 127
TANKGUARD SPECIAL MIDCOAT,YELLOW FC 100 63 100 159 30 52 h 18 d 20 h 7 d 10 h 4 d 23 10 714 1020
TANKGUARD SPECIAL TOPCOAT,GREY SC 20 63 80 127 10 52 h 18 d 20 h 7 d 10 h 4 d 23 5 114 127
TANKGUARD SPECIAL TOPCOAT,GREY FC 100 63 100 159 30 52 h * 20 h * 10 h * 23 10 714 1020
Total 350

Remarks: Stripe coat recommended at free adges ;plating stiffeners ;weld seams;scollop hole and other difficult to reach / spray areas

Page 38 of 44
Technical specification
Project NB-Keppel Singmarine-H386-(+)-155-M-Supply/Anchor Prepared by James Yong - Jotun (Singapore) Pte. Ltd.
handling & misc..- Supply in Baku Shipyard

Customer Keppel Singmarine Approved by James Yong Version 9


Location BAKU SHIPYARD Date 09-Oct-15

Position Lube oil tanks Area 1 m No. 34


Surface Prep. Oil and grease etc. to be removed with a suitable detergent . The entire area to be high pressure fresh water washed at min. 250 bar in order to
remove salts and other contamination. When the surface is dry , entire surface area to be blast cleaned to min. Sa. 2.5 (ISO 8501-1:2007) with
blast profile above 50 microns.
Product Type Area to Vol. solids Filmthickness (m) Loss Recoating intervals Thinner Consumption (l)
of paint % % (%) 10C 23C 40C
coat Dry spec. Wet spec. Min Max Min Max Min Max No. Max Theor. Practical
%
PENGUARD PRIMER,RED FC 100 51 50 98 30 8 h 9 mth 4 h 9 mth 3 h 9 mth 17 10 0 0
TANKGUARD HB,GREYISH GREEN FC 100 50 150 300 30 24 h 1 mth 6 h 21 d 4 h 7d 23 10 0 0
TANKGUARD HB,LIGHT GREY SC 20 50 100 200 10 24 h 1 mth 6 h 21 d 4 h 7d 23 5 0 0
TANKGUARD HB,GREYISH GREEN SC 20 50 100 200 10 24 h 1 mth 6 h 21 d 4 h 7d 23 5 0 0
TANKGUARD HB,LIGHT GREY FC 100 50 150 300 30 24 h * 6h * 4h * 23 10 0 0
Total 350

Remarks: Stripe coat recommended at free edges ;plating stiffeners ;welding seams ;scollop hole and other difficult to reach / spray areas

Page 39 of 44
Technical specification
Project NB-Keppel Singmarine-H386-(+)-155-M-Supply/Anchor Prepared by James Yong - Jotun (Singapore) Pte. Ltd.
handling & misc..- Supply in Baku Shipyard

Customer Keppel Singmarine Approved by James Yong Version 9


Location BAKU SHIPYARD Date 09-Oct-15

Position Shop Blast Primer Area 1 m No. 35


Surface Prep. Oil and grease etc. to be removed with a suitable detergent . The entire area is to be blast cleaned to min. Sa. 2.5 (ISO 8501-1:2007).
Product Type Area to Vol. solids Filmthickness (m) Loss Recoating intervals Thinner Consumption (l)
of paint % % (%) 10C 23C 40C
coat Dry spec. Wet spec. Min Max Min Max Min Max No. Max Theor. Practical
%
MUKI Z 2001,GREY FC 100 28 20 71 40 * * 1d * 1d * 4 5 0 0
Total 20

Remarks:

Page 40 of 44
Technical specification
Project NB-Keppel Singmarine-H386-(+)-155-M-Supply/Anchor Prepared by James Yong - Jotun (Singapore) Pte. Ltd.
handling & misc..- Supply in Baku Shipyard

Customer Keppel Singmarine Approved by James Yong Version 9


Location BAKU SHIPYARD Date 09-Oct-15

Position Helideck - Support Structure Area 1000 m No. 36


Surface Prep. Oil and grease etc. to be removed with a suitable detergent . The entire area to be high pressure fresh water washed at min. 250 bar in order to
remove salts and other contamination . When the surface is dry, entire surface area to be blast cleaned to min. Sa. 2.5 (ISO 8501-1:2007) with
blast profile above 50 microns
Product Type Area to Vol. solids Filmthickness (m) Loss Recoating intervals Thinner Consumption (l)
of paint % % (%) 10C 23C 40C
coat Dry spec. Wet spec. Min Max Min Max Min Max No. Max Theor. Practical
%
JOTAMASTIC 80,ALUMINIUM RED TONED FC 100 80 125 156 40 24 h 18 d 10 h 14 d 4 h 14 d 17 5 156 260
JOTAMASTIC 80,GREY FC 100 80 125 156 40 24 h NR 10 h NR 4h NR 17 5 156 260
HARDTOP XP,COAST WHITE 7001 FC 100 63 50 79 40 14 h * 7h * 4h * 10 5 79 132
Total 300

Remarks: After final coat;any burnt mark will be power tool and touch up as per spec. For Jotamastic 80 product;Wintergrade type will be used when substrate
temperature reaches 15 c and below.

Page 41 of 44
Technical specification
Project NB-Keppel Singmarine-H386-(+)-155-M-Supply/Anchor Prepared by James Yong - Jotun (Singapore) Pte. Ltd.
handling & misc..- Supply in Baku Shipyard

Customer Keppel Singmarine Approved by James Yong Version 9


Location BAKU SHIPYARD Date 09-Oct-15

Position Helideck -Landing Pad Area 500 m No. 37


Surface Prep. Oil and grease etc. to be removed with a suitable detergent . The entire area to be high pressure fresh water washed at min. 250 bar in order to
remove salts and other contamination . When the surface is dry , entire surface area to be blast cleaned to min. Sa. 2.5 (ISO 8501-1:2007) with
blast profile above 50 microns
Product Type Area to Vol. solids Filmthickness (m) Loss Recoating intervals Thinner Consumption (l)
of paint % % (%) 10C 23C 40C
coat Dry spec. Wet spec. Min Max Min Max Min Max No. Max Theor. Practical
%
JOTAMASTIC 80,ALUMINIUM RED TONED FC 100 80 125 156 40 24 h 18 d 10 h 14 d 4 h 14 d 17 5 78 130
JOTAMASTIC 80,GREY FC 100 80 125 156 40 24 h NR 10 h NR 4h NR 17 5 78 130
HARDTOP FLEXI,WHITE FC 100 64 60 94 40 6h * 3h * 1.5 h * 10 5 47 78
HARDTOP FLEXI,YELLOW 258 SC 20 64 60 94 20 * * * * * * 10 5 9 12
HARDTOP FLEXI,GREEN 257 SC 20 64 60 94 20 6h * 3h * 1.5 h * 10 5 9 12
Total 310

Remarks: After final coat;any burnt mark will be power tool and touch up as per spec. For Jotamastic 80 product;Wintergrade type will be used when substrate
temperature reaches 15 c and below.

Page 42 of 44
Technical specification
Project NB-Keppel Singmarine-H386-(+)-155-M-Supply/Anchor Prepared by James Yong - Jotun (Singapore) Pte. Ltd.
handling & misc..- Supply in Baku Shipyard

Customer Keppel Singmarine Approved by James Yong Version 9


Location BAKU SHIPYARD Date 09-Oct-15

Position Chain Locker Area 200 m No. 38


Surface Prep. Oil and grease etc. to be removed with a suitable detergent . The entire area to be high pressure fresh water washed at min. 250 bar in order to
remove salts and other contamination if require. When the surface is dry, entire surface area to be blast cleaned to min. Sa. 2.5 (ISO 8501-1:2007)
with blast profile above 50 microns
Product Type Area to Vol. solids Filmthickness (m) Loss Recoating intervals Thinner Consumption (l)
of paint % % (%) 10C 23C 40C
coat Dry spec. Wet spec. Min Max Min Max Min Max No. Max Theor. Practical
%
JOTAMASTIC 80,ALUMINIUM RED TONED FC 100 80 150 188 40 24 h 18 d 10 h 14 d 4 h 14 d 17 5 38 63
JOTAMASTIC 80,BLACK FC 100 80 150 188 40 24 h * 10 h * 4h * 17 5 38 63
Total 300

Remarks: .After final coat;any burnt mark will be power tool and touch up as per spec. For Jotamastic 80 product;Wintergrade type will be used when substrate
temperature reaches 15 c and below.

Page 43 of 44
* please refer to the relevant technical datasheets and AG application guide for recoating and curing conditions
NR: Not recommended for this exposure or generic type:
Unless otherwise agreed in writing, all product supplied and technical advice given by us are subject to our standard terms and conditions of sale. In the event that supplies are made and
technical advice is given by one of our associated companies or dealers, then such supplies and technical advice shall be subject to the standard terms of sale of that company, a copy of
which is available upon request. The given data must be considered as guidelines only, the figures in some columns may be rounded. Drying times and paint consumptions may vary
depending on actual conditions.
For updated information about our products please refer to our web site at www.jotun.com

Page 44 of 44

Das könnte Ihnen auch gefallen