Beruflich Dokumente
Kultur Dokumente
Operating Instructions GB
Manual de instrucciones ES
CS
CDX-S11S
CDX-S11
2005 Sony Corporation
Welcome ! Warning if your cars ignition has no
ACC position
Thank you for purchasing this Sony Compact After turning the ignition off, be sure to press
Disc Player. You can enjoy your drive with the and hold (OFF) on the unit until the display
following functions. disappears.
CD playback Otherwise, the display does not turn off and
You can play CD-DA and CD-R/CD-RW for this causes battery drain.
audio use.
Radio reception
You can store up to 6 stations per band (FM1, This label is located on the bottom of the
FM2, FM3, AM1 and AM2). chassis.
BTM (Best Tuning Memory): the unit selects
strong signal stations and stores them.
Sound adjustment
EQ3: You can select an equalizer curve for 7
music types.
2
Table of Contents
3
Getting Started Detaching the front panel
Resetting the unit You can detach the front panel of this unit to
prevent theft.
Before operating the unit for the first time, or
after replacing the car battery or changing the Caution alarm
connections, you must reset the unit. If you turn the ignition switch to the OFF
Detach the front panel and press the RESET position without detaching the front panel, the
button with a pointed object, such as a ballpoint caution alarm will sound for a few seconds.
pen. The alarm will only sound if the built-in
amplifier is used.
1 Press (OFF).
RESET The unit is turned off.
button
2 Press , then pull it off towards you.
Note
Pressing the RESET button will erase the clock setting
and some stored contents.
(OFF)
Setting the clock
The clock uses a 12-hour digital indication.
1 Press and hold (SEL).
The setup display appears. Notes
2 Press (SEL) repeatedly until CLOCK- Do not drop or put excessive pressure on the front
ADJ appears. panel and display window.
Do not subject the front panel to heat/high
3 Press (DSPL). temperature or moisture. Avoid leaving it in a parked
The hour indication flashes. car or on a dashboard/rear tray.
A
B
Note
Do not put anything on the inner surface of the front
panel.
4
Location of controls and basic operations
Main unit
1 2 34 5 6 7 8 9 0
SEL
CDX-S11S
qa qs qd qf qg qh qj qk CDX-S11
5
Radio Other functions
Storing and receiving stations Changing the sound settings
Caution
When tuning in stations while driving, use Best Adjusting the sound
Tuning Memory (BTM) to prevent an accident. characteristics BAL/FAD/SUB
You can adjust the balance, fader and subwoofer
volume.
Storing automatically BTM
1 Press (SEL) repeatedly until BAL,
1 Press (SOURCE) repeatedly until FAD or SUB appears.
TUNER appears. The item changes as follows:
To change the band, press (MODE)
repeatedly. You can select from FM1, FM2, LOW*1 t MID*1 t HI*1 t
FM3, AM1 or AM2. BAL (left-right) t FAD (front-rear) t
SUB (subwoofer volume)*2
2 Press and hold (BTM) until BTM *1 When EQ3 is activated (page 6).
flashes. *2 When the audio output is set to SUB (page 7).
The unit stores stations in order of frequency ATT is displayed at the lowest setting, and can
on the number buttons. be adjusted up to 20 steps.
A beep sounds when the setting is stored.
2 Press the volume +/ button
repeatedly to adjust the selected item.
Storing manually After 3 seconds, the setting is complete and
the display returns to normal play/reception
1 While receiving the station that you mode.
want to store, press and hold a
number button ((1) to (6)) until
MEM appears. Customizing the equalizer curve
The number button indication appears in the EQ3
display. CUSTOM of EQ3 allows you to make your
Note own equalizer settings.
If you try to store another station on the same number
button, the previously stored station will be replaced. 1 Select a source, then press (EQ3)
repeatedly to select CUSTOM.
2 Press (SEL) repeatedly until LOW,
Receiving the stored stations MID or HI appears.
1 Select the band, then press a number 3 Press the volume +/ button
button ((1) to (6)). repeatedly to adjust the selected item.
The volume level is adjustable in 1 dB steps,
from 10 dB to +10 dB.
Tuning automatically
1 Select the band, then press (SEEK) +/
to search for the station.
Scanning stops when the unit receives a Repeat steps 2 and 3 to adjust the equalizer
station. Repeat this procedure until the curve.
desired station is received. To restore the factory-set equalizer curve,
press and hold (SEL) before the setting is
Tip complete.
If you know the frequency of the station you want to
listen to, press and hold (SEEK) +/ to locate the
After 3 seconds, the setting is complete and
approximate frequency, then press (SEEK) +/ the display returns to normal play/reception
repeatedly to fine adjust to the desired frequency mode.
(manual tuning). Tip
Other equalizer types are also adjustable.
6
Adjusting setup items SET Additional Information
1 Press and hold (SEL). Precautions
The setup display appears.
2 Press (SEL) repeatedly until the If your car has been parked in direct sunlight,
desired item appears. allow the unit to cool off before operating it.
Power aerial will extend automatically while the
3 Press the volume +/ button to select unit is operating.
the setting (example ON or OFF).
4 Press and hold (SEL). Moisture condensation
The setup is complete and the display returns On a rainy day or in a very damp area, moisture
to normal play/reception mode. condensation may occur inside the lenses and
display of the unit. Should this occur, the unit will
Note not operate properly. In such a case, remove the disc
Displayed items will differ, depending on the source and wait for about an hour until the moisture has
and setting. evaporated.
The following items can be set (follow the page
reference for details): To maintain high sound quality
z indicates the default settings. Be careful not to splash juice or other soft drinks
onto the unit or discs.
CLOCK-ADJ (Clock Adjust) (page 4)
BEEP Notes on discs
To set BEEP-ON (z) or BEEP-OFF. To keep a disc clean, do not touch its surface.
SUB/REAR*1 Handle the disc by its edge.
Keep your discs in their cases or disc magazines
To switch the audio output. when not in use.
SUB (z): to output to a subwoofer. Do not subject discs to heat/high temperature.
REAR: to output to a power amplifier. Avoid leaving them in a parked car or on a
DIM (Dimmer) dashboard/rear tray.
To change the brightness of the display. Do not attach labels, or use discs with sticky ink/
DIM-ON: to dim the display. residue. Such discs may stop spinning when used,
DIM-OFF (z): to deactivate the dimmer. causing a malfunction, or may ruin the disc.
DEMO*1 (Demonstration)
To set DEMO-ON (z) or DEMO-OFF.
LPF*2 (Low Pass Filter)
To select the subwoofer cut-off frequency
78HZ, 125HZ or OFF (z).
*1 When the unit is turned off. Do not use any discs with labels or stickers
*2 When the audio output is set to SUB. attached.
The following malfunctions may result from using
such discs:
Inability to eject a disc (due to a label or sticker
peeling off and jamming the eject mechanism).
Inability to read audio data correctly (e.g.,
playback skipping, or no playback) due to heat
shrinking of a sticker or label causing a disc to
warp.
Discs with non-standard shapes (e.g., heart,
square, star) cannot be played on this unit.
Attempting to do so may damage the unit. Do not
use such discs.
You cannot play 8 cm CDs.
7
Before playing, clean the discs Cleaning the connectors
with a commercially available The unit may not function properly if the connectors
cleaning cloth. Wipe each disc between the unit and the front panel are not clean. In
from the centre out. Do not use order to prevent this, detach the front panel (page 4)
solvents such as benzine, and clean the connectors with a cotton swab dipped
thinner, commercially available in alcohol. Do not apply too much force. Otherwise,
cleaners, or antistatic spray the connectors may be damaged.
intended for analogue discs.
8
2 Remove. the unit. Power amplifier section
1 Insert both release keys simultaneously Outputs: Speaker outputs (sure seal connectors)
until they click. Speaker impedance: 4 8 ohms
Maximum power output: 45 W 4 (at 4 ohms)
General
Hook facing
inwards. Outputs:
Audio outputs terminal (sub/rear switchable)
Power aerial relay control terminal
Power amplifier control terminal
Input:
Aerial input terminal
Tone controls:
Low: 10 dB at 60 Hz (XPLOD)
2 Pull the release keys to unseat the unit. Mid: 10 dB at 1 kHz (XPLOD)
High: 10 dB at 10 kHz (XPLOD)
Power requirements: 12 V DC car battery
(negative earth)
Dimensions: Approx. 178 50 178 mm (w/h/d)
Mounting dimensions: Approx. 182 53 161 mm
(w/h/d)
Mass: Approx. 1.2 kg
Supplied accessory:
3 Slide the unit out of the mounting. Parts for installation and connections (1 set)
Design and specifications are subject to change
without notice.
10
Advertencia: si el encendido del
automvil no dispone de una posicin
ACC
Tras apagar el motor, mantenga presionado
(OFF) en la unidad hasta que se apague la
pantalla.
Si no lo hace, la pantalla no se desactiva y se
Bienvenido desgasta la batera.
Gracias por adquirir este reproductor de discos
compactos Sony. Mientras Reproductor de discos
compactos FM/AM puede disfrutar de las
funciones siguientes:
Reproduccin de CD
Puede reproducir CD-DA y CD-R/CD-RW
para audio. Esta etiqueta est situada en la parte inferior
del chasis.
Recepcin de radio
Puede almacenar hasta 6 emisoras de radio
por banda (FM1, FM2, FM3, AM1 y AM2).
BTM (Best Tuning Memory - memoria de
emisoras con mejor sintona): la unidad
selecciona las emisoras que emiten la seal
ms ntida y las almacena.
Ajuste del sonido
EQ3: puede seleccionar una curva de
ecualizador para 7 tipos de msica.
2
Tabla de Contenido
3
Procedimientos iniciales Extraccin del panel frontal
Restauracin de la unidad Puede extraer el panel frontal de la unidad para
evitar que la roben.
Antes de utilizar la unidad por primera vez, o
despus de sustituir la batera del automvil o de Alarma de precaucin
cambiar las conexiones, debe restaurarla. Si gira el interruptor de encendido hasta la
Extraiga el panel frontal y presione el botn posicin OFF sin haber extrado el panel frontal,
RESET con un objeto puntiagudo, como un la alarma de precaucin sonar durante unos
bolgrafo. segundos.
La alarma sonar nicamente si se utiliza el
amplificador incorporado.
Botn 1 Presione (OFF).
RESET
La unidad se apaga.
Nota 2 Presione y, a continuacin, extraiga
Al presionar RESET, se borra el ajuste del reloj y el panel frontal hacia usted.
algunos contenidos memorizados.
A
B
Nota
No coloque nada sobre la superficie interior del panel
frontal.
4
Ubicacin de los controles y las operaciones bsicas
Unidad principal
1 2 34 5 6 7 8 9 0
SEL
CDX-S11S
qa qs qd qf qg qh qj qk CDX-S11
Almacenamiento manual
1 Mientras recibe la emisora que desea
almacenar, mantenga presionado un
botn numrico de ((1) a (6)) hasta
que aparezca MEM.
La indicacin de botn numrico aparece en
pantalla.
Nota
Si intenta almacenar otra emisora en el mismo botn
numrico, se reemplazar la que estaba almacenada
previamente.
6
Sugerencia
Otras funciones Tambin es posible ajustar otros tipos de ecualizador.
No use discos con etiquetas o autoadhesivos. Si desea realizar alguna consulta o solucionar
Su uso puede producir las siguientes fallas de algn problema relativo a la unidad que no se
funcionamiento: trate en este manual, pngase en contacto con el
Imposibilidad de expulsar el disco (dado que se distribuidor Sony ms cercano.
despeg la etiqueta o el autoadhesivo y se
obstruye el mecanismo de expulsin).
Imposibilidad de leer los datos de audio en
forma correcta (por ejemplo, se interrumpe la
reproduccin o simplemente no funciona)
debido a que el calor contrae el autoadhesivo o la
etiqueta y hace que el disco se deforme.
8
3 Tire de las llaves de liberacin para extraer
Mantenimiento el marco de proteccin.
Unidad principal Parte posterior del panel 3 Deslice la unidad para extraerla de la
frontal montura.
Notas
Por razones de seguridad, apague el motor antes de
limpiar los conectores y extraiga la llave del
interruptor de encendido.
No toque nunca los conectores directamente con los
dedos ni con ningn dispositivo metlico.
Especificaciones
Extraccin de la unidad
Seccin del reproductor de CD
1 Extraiga el marco de proteccin. Relacin seal-ruido: 120 dB
1 Extraiga el panel frontal (pgina 4). Respuesta de frecuencia: de 10 a 20 000 Hz
Fluctuacin y trmolo: Inferior al lmite medible
2 Fije las llaves de liberacin al marco de
proteccin. Seccin del sintonizador
FM
Rango de sintonizacin:
de 87,5 a 108,0 MHz (a intervalos de 50 kHz)
de 87,5 a 107,9 MHz (a intervalos de 200 kHz)
Intervalo de sintonizacin de FM: 50 kHz/200 kHz
conmutable
Terminal de la antena area: Conector de antena
Oriente la llave de liberacin externa
como se ilustra.
Frecuencia intermedia: 10,7 MHz/450 kHz
Sensibilidad til: 9 dBf
Selectividad: 75 dB a 400 kHz
contina en la pgina siguiente t
9
Relacin seal-ruido: 67 dB (estreo), 69 dB (mono)
Distorsin armnica a 1 kHz: 0,5 % (estreo), Solucin de problemas
0,3 % (mono)
Separacin: 35 dB a 1 kHz La siguiente lista de comprobacin le ayudar a
Respuesta de frecuencia: de 30 a 15 000 Hz solucionar los problemas que puedan producirse
AM con la unidad.
Rango de sintonizacin: Antes de consultarla, revise los procedimientos
de 531 a 1 602 kHz (a intervalos de 9 kHz) de conexin y de funcionamiento.
de 530 a 1 710 kHz (a intervalos de 10 kHz)
Intervalo de sintonizacin de AM: 9 kHz/10 kHz
conmutable Generales
Terminal de la antena area: Conector de antena La unidad no recibe alimentacin.
externa Revise la conexin. Si todo est en orden, revise el
Frecuencia intermedia: 10,7 MHz/450 kHz fusible.
Sensibilidad: 30 V
La antena motorizada no se extiende.
Seccin del amplificador de potencia La antena motorizada no tiene una caja de rel.
Salidas: Salidas de altavoz (conectores de sellado No se emite sonido.
seguro) El volumen es demasiado bajo.
Impedancia de altavoces: de 4 a 8 La funcin ATT est activada.
Salida mxima de potencia: 45 W 4 (a 4 ) La posicin del control de equilibrio FAD no est
ajustada para un sistema de 2 altavoces.
Generales No se escuchan pitidos.
Salidas: El sonido de los pitidos est cancelado
Terminal de salidas de audio (se pueden cambiar (pgina 7).
entre sub y posterior) Se conect un amplificador de potencia opcional y no
Terminal de control del rel de la antena est usando el amplificador incorporado.
motorizada
Terminal de control del amplificador de potencia El contenido de la memoria se borr.
Entrada: Presion el botn RESET.
Terminal de entrada de antena t Vuelva a almacenar los datos en la memoria.
Controles de tono: Se desconect el cable de conexin de alimentacin o
Bajos: de 10 dB a 60 Hz (XPLOD) la pila.
Medios: de 10 dB a 1 kHz (XPLOD) El cable de conexin de la alimentacin no est
Altos: de 10 dB a 10 kHz (XPLOD) conectado en forma correcta.
Requisitos de alimentacin: Batera de automvil de
Las emisoras almacenadas y la hora correcta
cc 12 V (masa negativa)
se borraron.
Dimensiones: Aprox. 178 50 178 mm (an/al/prf)
Dimensiones de montaje: Aprox. 182 53 161 mm El fusible se fundi.
(an/al/prf) Se escucha ruido cuando se cambia la
Peso: Aprox. 1,2 kg posicin de la llave de encendido.
Accesorio suministrado: Los cables no coinciden correctamente con el conector
Componentes de instalacin y conexiones de alimentacin auxiliar del automvil.
(1 juego) Las indicaciones desaparecen de la pantalla o
El diseo y las especificaciones estn sujetos a no aparecen.
cambios sin previo aviso. El atenuador est ajustado en DIM-ON
(pgina 7).
La pantalla se apaga si mantiene presionado (OFF).
t Mantenga presionado (OFF) en la unidad hasta
que aparezca la pantalla.
Se ha utilizado soldadura sin plomo para soldar Los conectores estn sucios (pgina 9).
ciertos componentes. (ms del 80 %)
Ciertas placas del circuito impreso no contienen
retardantes de llama halogenados.
Las carcasas no contienen retardantes de llama
halogenados.
Impreso con tinta de aceites vegetales, libre de
COV (Compuestos Orgnicos Voltiles).
No se ha utilizado goma esponjosa de poliestireno
para el material de relleno y proteccin.
10
Reproduccin de CD Un programa de FM emitido en estreo se
No es posible insertar el disco. escucha en monoaural.
Ya hay un disco insertado. La unidad se encuentra en el modo de recepcin
El disco se insert a la fuerza al revs o en forma monoaural.
incorrecta. t Presione (SENS) hasta que aparezca MONO-
OFF.
La reproduccin no se inicia.
Disco defectuoso o sucio.
Los discos CD-R/CD-RW no son para audio (pgina Mensajes/indicaciones de error
8).
Se producen saltos de sonido. ERROR
La instalacin no es correcta. El disco est sucio o se insert al revs.
t Instale la unidad en un ngulo inferior a t Lmpielo o insrtelo en forma correcta.
45 en una parte firme del automvil. Se insert un disco en blanco.
Disco defectuoso o sucio. El disco no se reproduce debido a algn problema.
Los botones de operacin no funcionan. t Inserte otro disco.
El disco no se expulsar. FAILURE
Presione el botn RESET (pgina 4). La conexin del altavoz/amplificador no es correcta.
t Consulte el manual de instalacin o de conexiones
suministrado para comprobar la conexin.
Recepcin de radio
L.SEEK +/
No es posible recibir las emisoras.
El modo de bsqueda local est activado durante la
Hay ruidos que obstaculizan el sonido.
sintonizacin automtica.
Conecte un cable de control de antena motorizada
(azul) o un cable de fuente de alimentacin auxiliar OFFSET
(rojo) al cable de suministro de alimentacin del Es posible que se produjera una falla interna.
amplificador de antena del automvil (slo si el auto t Revise la conexin. Si el indicador de error
dispone de una antena FM/AM incorporada en el permanece en pantalla, pngase en contacto con el
cristal posterior o lateral). distribuidor Sony ms cercano.
Revise la conexin de la antena del automvil. RESET
La antena automtica no se extiende. La unidad no puede utilizarse debido a algn
t Revise la conexin del cable de control de la problema.
antena motorizada. t Presione el botn RESET (pgina 4).
Revise la frecuencia. o
No es posible utilizar la sintonizacin Durante la operacin de avance o retroceso rpido,
programada. lleg al principio o al final del disco y no es posible
Almacene la frecuencia correcta en la memoria. continuar.
La seal de emisin es demasiado dbil.
No es posible utilizar la sintonizacin Si estas soluciones no ayudan a mejorar la situacin,
automtica. pngase en contacto con el distribuidor Sony ms
El ajuste del modo de bsqueda local no es correcto. cercano.
t La sintonizacin se detiene con demasiada Si entrega la unidad para su reparacin a causa de
frecuencia: problemas en la reproduccin de discos, lleve el
Presione (SENS) hasta que aparezca LOCAL- disco que se utiliz cuando comenz el problema.
ON.
t La sintonizacin no se detiene en una emisora:
Presione (SENS) varias veces hasta que aparezca
MONO-ON o MONO-OFF (FM), o
LOCAL-OFF (AM).
La seal de emisin es demasiado dbil.
t Use la sintonizacin manual.
Durante la recepcin de FM, la indicacin ST
parpadea.
Sintonice la frecuencia con precisin.
La seal de emisin es demasiado dbil.
t Presione (SENS) para ajustar el modo de
recepcin monoaural en MONO-ON.
11
Sony
CD
CD-DA CD-R/CD-RW
FM1FM2FM3AM1 AM2
6
BTM
EQ3 7
..............................4 ......................... 6
..............................4 BAL/FAD/SUB.......... 6
............................4 EQ3 ............... 6
.........................4 SET .................... 7
..............................5 ....................... 7
....................... 7
................................. 8
............................. 8
........................6 ................................. 9
BTM ......................6 ............................. 9
...........................6 / .................... 10
...................6
...........................6
OFF
RESET
1 (OFF)
RESET
2
RESET
(OFF)
12
1 (SEL)
2 (SEL) CLOCK-ADJ
3 (DSPL) /
/
4 +/-
(DSPL)
5 (SEL) A B
6 (SEL)
(DSPL) (DSPL)
A
B
1 2 34 5 6 7 8 9 0
SEL
CDX-S11S
qa qs qd qf qg qh qj qk CDX-S11
5
BAL/FAD/SUB
BTM
1
(1) (6)MEM EQ3
EQ3 CUSTOM
1 (EQ3)
CUSTOM
2 (SEL) LOWMID
HI
1 (1) 3 +/-
(6) 1 dB -10 dB
+10 dB
1 (SEEK) +/- 2 3
(SEL)
3 /
(SEEK) +/
(SEEK) +/
6
SET
1 (SEL)
2 (SEL)
3 +/- ON
OFF
4 (SEL)
/
z
CLOCK-ADJ 4
BEEP
BEEP-ONz BEEP-OFF
SUB/REAR*1
/
SUBz /
REAR /
DIM
DIM-ON
DIM-OFFz
DEMO*1
DEMO-ONz DEMO-OFF
LPF*2
78HZ
125HZ OFFz
*1
*2 SUB
8 cm CD
7
CD-R/CD-RW
CD-R/CD-RW
CD-R/CD-RW 1
1 4
Compact Disc (CD) 2
CD
Sony
2
1
Sony
10A
2
4
8
CD
120 dB
10 - 20000 Hz
FM
60 Hz 10 dB XPLOD
1 kHz 10 dB XPLOD DIM-ON 7
10 kHz 10 dB XPLOD (OFF)
12 V DC t (OFF)
178 50 178 mm / / 8
182 53 161 mm / /
1.2 kg
CD
CD-R/CD-RW 8
9
/
t 45
ERROR
t
RESET 4
t
FAILURE
/
t /
L.SEEK +/
/ FM/AM
OFFSET
t
Sony
t
RESET
t RESET 4
t
(SENS) LOCAL-ON
t Sony
(SENS) MONO-ON CD
MONO-OFFFMLOCAL-OFFAM
t
FM ST
t (SENS)
MONO-ON
FM
t (SENS) MONO-OFF
10
Sony Corporation Printed in Thailand