Beruflich Dokumente
Kultur Dokumente
Masimo SET, LNOP and CleanShield are U.S. registered trademarks of Masimo Corp.
Copyright Mindray DS USA, Inc., 2008. All rights reserved. Contents of this publication may not be reproduced in any
form without permission of Mindray DS USA, Inc.
Foreword
This service manual gives a detailed description of the Duo Portable Patient Monitor,
including circuit descriptions, test and calibration procedures, and spare parts listings. This
manual is intended as a guide for technically qualified personnel during repair, testing, or
calibration procedures.
A WARNING is provided to alert the user to potential serious outcomes (death, injury, or
serious adverse events) to the patient or the user.
A CAUTION is provided to alert the user to use special care necessary for the safe and
effective use of the device. They may include actions to be taken to avoid effects on patients
or users that may not be potentially life threatening or result in serious injury, but about which
the user should be aware. Cautions are also provided to alert the user to adverse effects on
this device of use or misuse and the care necessary to avoid such effects.
1.1 Introduction
The Duo is a compact, lightweight, portable patient monitor intended for monitoring the
following vital signs: blood pressure, SpO2 (optional), and pulse rate on adult and pediatric
patients. The Duo monitor can be powered by either the internal rechargeable Lithium-Ion
battery or external 100~240 volt 50/60 Hz AC.
Fan
Driver SpO 2 Module
NIBP Module
Isolated SpO 2
AC Input Power Supply*
* The Isolated SpO2 Power Supply is present with optional Masimo and Nellcor SpO2 ONLY.
** The RS232 - TTL Inverter and Serial Interface Connector is used for software updates by Service
Power ON / OFF
Control Circuit
AC Input
AC / DC
Converter
3.3v DC/DC 12v DC/DC
Converter Converter
Location Function
Measure across C5 Primary Rectified Voltage (DC). Range: 105 - 374 volts.
Measure across C12 +10.5 vdc input for Fan Driver board.
Temperature
Detector
DC Fan Driver
Fan
Input Circuit
CPU
Keypad
To To
SpO2 NIBP
Module Module
FPGA User Interface
To
External Serial Interface
Interface
LED Array Indicator
Display LEDs
2.1 Introduction
The following procedures are provided to verify the proper operation of the Duo monitor. A
menu driven interface is used to execute all verification tests. Performance tests should be
performed at least once per year and after any preventive maintenance or repair has been
performed.
7. To return to normal operation, press the Power ON/OFF key for two (2) seconds to
turn the Duo off.
8. You may then turn the Duo back on to resume normal operation.
Normal polarity
Normal polarity with open neutral
Reverse polarity
4. Verify the current reading is <100 uA under normal operating conditions; <300 uA
under single fault conditions for 120 VAC and <500 uA under single fault conditions for
230 VAC.
When the monitor enters the NIBP Calibration Mode, message code 525 will be
displayed in the Information Codes window. Release the buttons simultaneously.
3. Momentarily press the NIBP START/STOP button to start the NIBP calibration. Vent the
Test Chamber and verify the Duo and the manometer read zero. Using the bulb,
pressurize the test chamber to 50 mmHg and verify the Duo reading agrees with the
manometer +/- 3 mmHg. Using the bulb, increase the pressure to 200 mmHg and verify
the Duo reading agrees with the manometer +/- 3 mmHg.
SpO2 = 98%
Pulse Rate = 70
4. Verify that the displayed SpO2 and pulse rate values on the Duo monitor are +/- 2% of
the simulator target values.
5. Change the simulator values.
6. Verify the displayed values on the Duo monitor are equal to the simulator values +/- 2%.
3.1 Introduction
This section contains exploded views of the Duo monitor, internal modules, and parts list.
18
19
10
10
12
12
11
11
12
12
13
13
14
14
18
12 16 16a
10
15
17
17a
5 4
21
20
5
19
11
5
Battery Latch Detail
22
99
34
37
35
38
36
39
37
40
38
41
40
43
42
39
Screws,
mounting plate*
Duo monitor
Washers, locking* mounting plate*
Mounting screw
for basket*
Utility basket
Mounting screw
for basket*
Casters, locking
Casters, Non locking
Washers, locking*
Display Overlay
LANGUAGE OPTION PART NUMBER
English NIBP Only 0330-00-0053-01
English NIBP/SpO2 0330-00-0053-11
Connector Label
DESCRIPTION PART NUMBER
No SpO2 0334-00-1602-01
Masimo SpO2 0334-00-1602-02
Nellcor SpO2 0334-00-1602-04
4.1 Introduction
This chapter of the Duo Service Manual provides the necessary technical information
needed to perform repairs on the instrument. The most important prerequisites for effective
troubleshooting are a thorough understanding of the instrument functions as well as an
understanding of the theory of operation.
Isolated Masimo
To P1 on Main SpO2
P1 Power P2 J3 SpO2 J1
Control Board Sensor
Board Module
Isolated Nellcor
To P1 on Main SpO2
P1 Power P2 J2 SpO2 J1
Control Board Sensor
Board Module
External
Interface
Serial RS232<>TTL P5
Interface Inverter
P1
P2 P3 Main
Power Control
Supply Board
Board P2 P1 NIBP
Cuff
Battery P1 P3 P4
Module
Fan
Fan P2 Drive P1
Board
Monitor Failures
MESSAGE/
PROBLEM REASON SOLUTION
No display after Bad line fuse Replace fuse
power-on, power
Bad power supply Replace power supply
indicator does not
light. Bad CPU/Display Replace CPU/Display board
board
NIBP or SpO2 will CPU/Display board or Isolate and replace defective board/module
not function. module failure.
Module Failures
MESSAGE/
PROBLEM REASON SOLUTION
NIBP cuff cannot Pinched or leaking hose Check hose and cuff. Replace as needed
be inflated. or cuff
Intermittently won't Loose cuff or patient Keep the patient quiet. Reapply cuff
take an NIBP movement
reading.
NIBP readings Incorrect cuff size. Use appropriate size cuff. Ensure correct cuff
inappropriately Incorrectly applied cuff application
high or low for
NIBP module is out of Calibrate/replace NIBP module
patient condition.
calibration
No SpO2 reading SpO2 sensor or cable Check sensor placement and connection. Replace
damaged or if damaged
disconnected
Sensor not on patient
SpO2 value is SpO2 sensor or cable Check sensor placement and connection. Replace
inaccurate damaged or if damaged
disconnected
Sensor not on patient
Coloring agent (dye) Retry after the coloring agent has dissipated
has been injected into
patient
Patient movement Keep patient quiet
Patient is cold Warm patient and retry
Patient is wearing nail Remove nail polish
polish
Mindray Medical Netherlands B.V. P.O. Box 26 3870 CA Hoevelaken The Netherlands
Tel: +31 33 25 44 911 Fax: +31 33 25 37 621
Mindray (UK) Limited 3 Percy Road St. Johns Park Huntingdon Cambridgeshire PE29 6SZ
United Kingdom Tel: 01480 416840 Fax: 01480 436588
Mindray Medical France SARL Europarc Crteil 123, Chemin des Bassins
94035 Crteil Cedex France Tel: (0)1.45.13.91.50 Fax: (0)1.45.13.91.51
Mindray Medical German GmbH Zwischen den Bchen 4 64625 Bensheim Germany
Tel: +49.6251.17524-0 Fax: +49.6251.17524-20
Mindray Medical International Ltd. 2813 Office Tower, Convention Plaza No 1 Harbour Road
Wanchai Hong Kong Tel: +852 2793 5596 Fax: +852 2344 8824
0002-08-8918