Beruflich Dokumente
Kultur Dokumente
www.gyproc.ie
Plastering Specifications
Concrete Blockwork Gyproc Floating Coat 3/5hrs Ruled to an even surface and
or Gyproc Base Coat properly scratched to form a key for the finish plaster.
Concrete Blockwork Gyproc Airtite 4/5hrs Ruled to an even surface as a parge coat only.
Concrete Blockwork Gyproc Dri-Coat 4/6hrs Replastering of walls following damp-proof course
treatment, delayed as long as possible to allow the
background to dry out.
Concrete Surfaces, suitably Gyproc Bonding 3/4hrs Bonding Coat applied with firm pressure, built out to
treated (see section 1.3) or required thickness ruled to an even surface and
Dense Concrete Blocks properly scratched to form a key for finish coat plaster.
4x2s Gyproc Bonding 3/4hrs Caulk joints with Gyproc Skimcoat, Carlite Finish
Gyproc Round Edge Greyboard or Gyproc Board Finish. Allow to set before
skimming commences.
Grey face of all square or Gyproc Bonding 3/4hrs Bedding in of Gyproc Paper Joint Tape into Gyproc
tapered edge Gyproc Joint Filler or Gyproc Pro Fill Filler.
Plasterboards
*Gypsum plaster should not be specified as a finish to Moisture Resistant Boards as the board is designed to be suitable for environ-
1.11 Boards, taping and filling is the recommended approach. However, if a plaster finish is required, the board should first be treated with
**Carlite Finish or Gyproc Skimcoat plaster must not be applied directly to Gyproc Airtite. Either a Gyproc DriLyner,
Gyproc Skimcoat plaster can be applied.
44
book 1_jan10:Layout 1 15/04/2010 17:31 Page 45
Plastering Specifications
COVERAGE PER GRADE OF FINISH APPROXIMATE SET THICKNESS OF
TONNE/THICKNESS OF TIME FINISH/COVERAGE PER TONNE
BASECOAT
117m2 at 10mm thickness Carlite Finish or 2/3 hrs 375m2 at 2mm thickness
key for the finish plaster. 102m2 at 10mm thickness Gyproc Skimcoat
parge coat only. 180m2 at 6mm thickness Carlite Finish or Gyproc Skimcoat 2/3hrs 375m2 at 2mm thickness
NOT applied directly**
g damp-proof course 125m2 at 11mm thickness Carlite Finish or Gyproc Skimcoat 2/3hrs 375m2 at 2mm thickness
possible to allow the
m pressure, built out to 121m2 at 10mm thickness Carlite Finish or Gyproc Skimcoat 2/3hrs 375m2 at 2mm thickness
even surface and
ey for finish coat plaster.
properly scratched Carlite Finish or Gyproc Skimcoat 2/3hrs 375m2 at 2mm thickness
coat, Carlite Finish 120m2 at 10mm thickness Carlite Finish or Gyproc Skimcoat 2/3hrs 375m2 at 2mm thickness
to set before
oint Tape into Gyproc Carlite Finish, Gyproc Skimcoat or 2/3hrs 300m2 at 2mm thickness
ller. Bonding Coat Gyproc Board Finish
r treating joints and
en surface and properly
nish coat plaster.
oint Tape into Gyproc 120m2 at 10mm thickness Carlite Finish or Gyproc Skimcoat 2/3hrs 375m2 at 2mm thickness
ller.
properly scratched Carlite Finish or Gyproc Skimcoat 2/3 hrs 375m2 at 2mm thickness
ments of higher than normal humidity, which no Gypsum plaster is designed to be suitable for. On exposed, untiled, Moisture Resistant
ThistleBond-it in accordance with section 1.6 . 6mm Gyproc Multiboards should also first be treated with ThistleBond-it. 1.11
Gyproc GypLyner or Gyproc GypLyner IWL system may be used in conjunction with Gyproc Airtite where either Carlite Finish or
45