Beruflich Dokumente
Kultur Dokumente
Turbine make/design
3. Rated Capacity (MW) 500 MW
4. VWO Capacity (MW) 537
5. Rated Condenser Vacuum (MM of Hg abs) 77
6. Rated CW Inlet Temp.0C 320C#1, 360C#2
7. Number of turbine cylinders 3 HP/IP/LP
8. Barring gear a) Type b) Speed (RPM) c) Location Motorised 11 On brg. No.
2 9. Critical Speeds (RPM) a) HP Rotor b) IP Rotor c) LP Rotor d) Combined I II III - - 2450 - -
2100 1300 4250 - 700 2150
10. Operation Frequency Regime a) Continuous Operation b) Limited Operation range
continuous at a stretch & total life time 47.5 - 53 Hz 53.0 Hz width no time delay
11. Droop/Regulation a) Standard droop % b) Droop ineffective range 6% 47.5-52.5 Hz
12. Governing
a) Type
b) Operation modes
c) Overspped tripping Speed
d) Dead band
e) Speed sensing device Nozzle Combined EHC i)+10% ii) 12% (mech. overspeed) 47.5-52.5 Hz
Inductive (works on principle of eddy current)
13. Turbine type Impulse HP/IP/LP
14. HP a) Type b) No. of casings c) No. of flows d) Blade carrier/blade type e) Inlet parameter
i) Pressure (KG/cm2)
ii) Temperature 0C
iii) Wheel chamber pressure
f) Exhaust Parameter i) Pressure (KG/cm2) iv) Temperature 0C Split 2 Single - 170 537 140.4
(during PG test ) 46 343
15. IP Casing a) Type b) No. of casings c) No. of flows d) Blade carrier/blade type e) Inlet
parameter i) Pressure (Kg/cm2) ii) Temperature 0C f) Exhaust Parameter i) Pressure (Kg/cm2) ii)
Temperature 0C Split 2 Double - 40.57 537 6.47 276.8
16. LP Casing a) Type b) No. of casings c) No. of flows d) Blade carrier/blade type e) Inlet
parameter i) Pressure (Kg/cm2) ii) Temperature 0C f) Exhaust Parameter i) Pressure (Kg/cm2) ii)
Temperature 0C Split 2 Double - 6.147 276.8 0.121 49.3
17. Bearing Pedestals Type a) HP front b) Between HP/IP c) Between IP/LP d) LP-1&LP-2 (if
applicable) e) Between LP & Generator Fixed Sliding Fixed Not applicable Fixed
18. Bearing Type/Size
I. HP front
II. Between HP & IP
III. Between IP & LP
IV. Between LP & Gen
. V. Between Gen. & Exciter
VI. Exciter Rear (mm x mm dia)
157 x 200 260 x 315 371 x 525 421 x 475 371 x 425 (Bet gen & Exc.) 211 x 250 (Exc rear)
19. Bearing Seating Type a) Bearing no. 1 b) Bearing no. 2 c) Bearing no. 3 d) Bearing no. 4 NA
20. Turbine rotors a) HP rotor i) Type ii) Weight iii) Length (coupling to coupling) b) IP rotor i)
Type ii) Weight iii) Length (coupling to coupling) c) LP rotor i) Type ii) Weight iii)Length (coupling
to coupling) Disc. Type 10.60 tonnes 5500 mm Disc. type 20.00 tonne 4667mm Disc 53.7 tonnes
6462
21. HP stage blading a) No. of blades /Stage No. b) Shroud type/section c) Root type/section NA
All integral All dove Tail
22. IP stage blading a) No. of blades / stage b) Shroud type/section c) Root type/section NA All
Integral shroud All dove. Tail
23. LP stage blading a) No. of blades / stage b) Shroud type/section c) Root type/section NA All
integral except last 2 stages which are Free standing. All dove tail except last 2 stages which are
FIR TREE type.
26. Turbovisory
a) Total expn. At HP front
b) Expansion at IP pedestal
c) Differential expn limits HP IP LP
d) Axial shift trip valve (Limit) 27.90 mm 11.70 mm + 8.31 mm to 0.52 mm + 13.95 mm to
1.48 mm + 16.00 mm to 4.0 mm + 0.8 mm
33.7 Emergency oil pump (DC) a) Make b) Speed (RPM) c) Discharge PR (ata) d) Rated flow
(dm3/Sec) e) Mounting location f) Mounting arrangement (V/H) g) Motor, make, rating Allweiler
1500 1.3 kg/cm2 1020 lit/min On Top of MOT Vertical 3.8 KW
33.8 Jacking Oil Pump a) No. of pumps AC/DC b) Type of pump/make c) Discharge pressure d)
Speed rpm e) Capacity f) Motor make, rating, frame size 2 a.c and 1 d.c. each for bearing 3, 4 &
5 Q34-010R BDZ Maximum pr. 250 kg/cm2 1450 rpm 1.5 lit/min. 8.7 KW
34.5 FRF Pumps a) Numbers b) Make & Type c) Rated flow d) Rated pressure e) Speed f) Motor
i) Make ii) Rating iii) Frame size
Two Aliweiler SNDAT 1300-42 876 lit/min 40 Kg/cm2 1500 rpm - 81KW - 34.6 FRF Regenerative
System a) Type of system b) Details of filter Earth filter Fine mesh filter c) Type d) Filter size
Fuller s earth Rotring, Attha pulgus clay - - Rotring fine filter