Beruflich Dokumente
Kultur Dokumente
Tentative Specification
Preliminary Specification
Approval Specification
Customer:
APPROVED BY SIGNATURE
Name / Title
Note
Please return 1 copy for your confirmation with your signature and
comments.
CONTENTS
1. GENERAL DESCRIPTION...................................................................................................................................... 4
1.1 OVERVIEW ..................................................................................................................................................... 4
1.2 FEATURES ..................................................................................................................................................... 4
1.3 MECHANICAL SPECIFICATIONS ................................................................................................................... 4
2. ABSOLUTE MAXIMUM RATINGS........................................................................................................................... 5
2.1 ABSOLUTE RATINGS OF ENVIRONMENT..................................................................................................... 5
2.2 PACKAGE STORAGE ..................................................................................................................................... 6
2.3 ELECTRICAL ABSOLUTE RATINGS (OPEN CELL) ........................................................................................ 6
3. ELECTRICAL CHARACTERISTICS........................................................................................................................ 7
3.1 TFT LCD MODULE.......................................................................................................................................... 7
4. BLOCK DIAGRAM OF INTERFACE........................................................................................................................ 9
4.1 TFT LCD MODULE.......................................................................................................................................... 9
5. INPUT TERMINAL PIN ASSIGNMENT.................................................................................................................. 10
5.1 TFT LCD MODULE INPUT ............................................................................................................................ 10
5.2 COLOR DATA INPUT ASSIGNMENT............................................................................................................. 12
5.3 FLICKER (Vcom) ADJUSTMENT................................................................................................................... 13
6. INTERFACE TIMING ............................................................................................................................................ 14
6.1 INPUT SIGNAL TIMING SPECIFICATIONS ................................................................................................... 14
6.2 POWER ON/OFF SEQUENCE ...................................................................................................................... 16
7. OPTICAL CHARACTERISTICS ............................................................................................................................ 17
7.1 TEST CONDITIONS ...................................................................................................................................... 17
7.2 OPTICAL SPECIFICATIONS ......................................................................................................................... 18
8. DEFINITION OF LABELS ..................................................................................................................................... 21
8.1 OPEN CELL LABEL....................................................................................................................................... 21
8.2 CARTON LABEL ........................................................................................................................................... 21
9. PACKAGING......................................................................................................................................................... 22
9.1 PACKING SPECIFICATIONS......................................................................................................................... 22
9.2 PACKING METHOD ...................................................................................................................................... 22
10. PRECAUTIONS.................................................................................................................................................. 24
10.1 ASSEMBLY AND HANDLING PRECAUTIONS............................................................................................. 24
10.2 SAFETY PRECAUTIONS ............................................................................................................................ 24
11. MECHANICAL CHARACTERISTIC ..................................................................................................................... 25
REVISION HISTORY
Page
Version Date Section Description
(New)
Ver. 2.1 Sep.12, 2012 All All The Approval Specification for 0.5mm Cell was first issued.
1. GENERAL DESCRIPTION
1.1 OVERVIEW
V236BJ1-P01 is a 23.6 TFT Liquid Crystal Display product with driver ICs and 1ch-LVDS interface. This product
supports 1366*768 HDTV format and can display 16.7M colors (8-bit / color).
1.2 FEATURES
CHARACTERISTICS ITEMS SPECIFICATIONS
Screen Diagonal [in] 23.6
Pixels [lines] 1366 x 768
Active Area [mm] 521.4705 (H) x 293.184 (V)
Sub-Pixel Pitch [mm] 0.12725 (H) x 0.38175 (V)
Pixel Arrangement RGB vertical stripe
Weight [g] TYP. 500 g
Physical Size [mm] 535.06(W) 307.34(H) 1.53(D) Typ.
Display Mode Transmissive mode / Normallly black
3000:1 Typ.
Contrast Ratio
(Typical value measure at CMIs module)
Glass thickness (Array / CF) [mm] 0.5 / 0.5
+88/-88(H), +88/-88(V) Typ. (CR20)
Viewing Angle (CR>20)
(Typical value measure at CMIs module)
Color Chromaticity * Please refer to color chromaticity on p.22
Cell Transparency [%] 5.5%
Polarizer Surface Treatment Anti-Glare coating (Haze 1%),Hard coating (3H)
100
90
80
60
Operating Range
40
20
Storage Range
10
-40 -20 0 20 40 60 80
Temperature (C)
Note (1) Permanent damage to the device may occur if maximum values are exceeded. Function operation
should be restricted to the conditions described under Normal Operating Conditions.
3. ELECTRICAL CHARACTERISTICS
3.1 TFT LCD MODULE
(Ta = 25 2 C)
Value
Parameter Symbol Unit Note
Min. Typ. Max.
0.1Vcc
GND
470us
Note (3) The specified power supply current is under the conditions at Vcc = 12 V, Ta = 25 2 C, f v = 60 Hz,
whereas a power dissipation check pattern below is displayed.
(1366x3x768)
X+C Board
INPUT CONNECTOR,
P-TWO=187053-30091 or FOXCONN=GS23302-1321S-7H
SELLVDS Mode
0V~0.7V VESA
2.7V~3.3V/Open JEIDA
L : Connect to GND, H : Connect to +3.3V
Note (4) Interface optional pin has internal scheme as following diagram. Customer should keep the interface
voltage levelrequirement which including Panel board loading as below.
3.3V
System Board Panel Board
>16K ohm
1K ohm
IC
Note (5) LVDS connector mating dimension range request is 0.93mm~1.0mm as below.
Note (6) The screw hole which is distant from the connector is merged with Ground.
6. INTERFACE TIMING
6.1 INPUT SIGNAL TIMING SPECIFICATIONS
(Ta = 25 2 C)
The input signal timing specifications are shown as the following table and timing diagram.
Signal Item Symbol Min. Typ. Max. Unit Note
Fclkin
Frequency 67.67 76 82 MHz
(=1/TC)
Input cycle to
LVDS Trcl 200 ps (2)
cycle jitter
Receiver
Spread spectrum
Clock Fclkin_mod Fclkin-2% Fclkin+2% MHz
modulation range
(3)
Spread spectrum
FSSM 200 KHz
modulation frequency
LVDS Setup Time Tlvsu 600 ps
Receiver
Data Hold Time Tlvhd 600 ps
Fr5 47 50 53 Hz
Frame Rate
Vertical Fr6 57 60 63 Hz
Active
Total Tv 778 806 986 Th Tv=Tvd+Tvb
Display
Term Display Tvd 768 768 768 Th
Blank Tvb 10 38 218 Th
Horizontal Total Th 1446 1560 1936 Tc Th=Thd+Thb
Active
Display Thd 1366 1366 1366 Tc
Display
Term Blank Thb 80 194 570 Tc
Note (1) Please make sure the range of pixel clock has follow the below equation :
Fclkin(max) Fr6 Tv Th
Fr5 Tv Th Fclkin (min)
Note (2) This module is operated in DE only mode and please follow the input signal timing diagram below :
Tv
Tvd Tvb
DE
Th
DCLK
Tc
Thd
Thb
DE
Note (3) The input clock cycle-to-cycle jitter is defined as below figures. Trcl = | T1 T|
Note (4) The SSCG (Spread spectrum clock generator) is defined as below figures.
Note (5) The LVDS timing diagram and the receiver skew margin is defined and shown in following figure.
RXCLK+/-
RXn+/-
TRSKM
0.1VCC 0.1Vcc
0V
LVDS Signals 0V
0T7T2
0T8T3
T7 T8
T5 T6
T9
0V
Note (1) The supply voltage of the external system for the module input should follow the definition of Vcc.
Note (2) Apply the lamp voltage within the LCD operation range. When the backlight turns on before the LCD
operation or the LCD turns off before the backlight turns off, the display may momentarily become
abnormal screen.
Note (3) In case of VCC is in off level, please keep the level of input signals on the low or high impedance. If
T2<0,that maybe cause electrical overstress failure.
Note (4) T4 should be measured after the module has been fully discharged between power off and on period.
Note (5) Interface signal shall not be kept at high impedance when the power is on.
Note (6) Vcc must decay smoothly when power-off.
7. OPTICAL CHARACTERISTICS
7.1 TEST CONDITIONS
Item Symbol Value Unit
o
Ambient Temperature Ta 252 C
The LCD module should be stabilized at given temperature for 1 hour to avoid abrupt temperature change during
measuring in a windless room.
Rcx 0.654 -
Red
Rcy 0.329 -
Gcx 0.274 -
Green x=0, Y =0
Color Gcy Viewing Angle at Normal 0.602 -
Direction -0.03 (1)
Chromaticity Bcx 0.133 +0.03 -
Standard light source C
Blue
Bcy 0.115 -
Wcx 0.310 -
White
Wcy 0.356 -
Response Time
Gray to x=0, Y =0 - 8.5 20 ms (1),(4)
gray with CMI Module.
x+ 80 88 -
Horizontal
Viewing x- CR20 (VA Model) 80 88 -
Deg. (1),(2)
Angle with CMI Module
Y+ 80 88 -
Vertical
Y- 80 88 -
Note (0) Light source is the standard light source C which is defined by CIE and driving voltage are based on
suitable gamma voltages. The calculating method is as following :
1.Measure Modules and BLUs spectrum at center point. W, R, G, B are with signal input. BLU
(V236BJ1-L01) is supplied by CMI.
2. Calculate cells spectrum.
3.Calculate cells chromaticity by using the spectrum of standard light source C.
Note (1) Light source is the BLU which supplied by CMI and driving voltage are based on suitable gamma
voltages.
Normal
x = y = 0
y- y+
X- = 90 x- 12 oclock direction
y+
x y+ = 90
x+
6 oclock
y- x+ X+ = 90
y- = 90
100%
90%
Optical
Gray Level 0
Response
10%
0%
Time
TR TF
Horizontal Line
W/4 1 2
Vertical Line
3W/4 3 4
Active Area
XXXXXXXXXXXXXX XXXXXXXXXXXXXX