Sie sind auf Seite 1von 4

Read this instruction manual carefully before use.

VHF/UHF BOOSTER for Home Use


Amplification
European Standard ch.5-12 & ch.21-69
American Standard ch.7-13 & ch.14-83
INSTRUCTION MANUAL
Channels
Chinese Standard ch.6-12 & ch.13-59
VHF/UHF Booster

VUB32LK2
With Remote Power Supply (15V DC)
Power Supply (Indoor use)

32dB TYPE
Grainy TV pictures clear up in an instant using our Booster!

Cut Weather boots according to


the thickness of cables to be used. F-type (Female)

(Coaxial cable length : 1.8m)


IEC/PAL(Male)
High Performance
Sufficient Output Level
MASter of PROduction

Beat (Stripes) or Wiper (Windshield Wipe Effect) The model allows a maximum output level of
interference will appear in the TV picture when a low- 107dBV (VHF)/104dBV (UHF), so interference is
rated-output-level booster is used in strong signal reduced even where reception level is strong.
areas. (Please see photos on page 3.)

Easy Handling Function


Screw Clamping Lid Compatible Input Mode Corresponds to
VHF/UHF Mixed or Separated Inputs
The lid of the Booster Case can
be closed snugly with the attached The input mode of the Booster allows you to select either VHF/UHF
screw. Mixed or Separated on the Input Mode Selector. A VHF/UHF compatible
TV antenna with mixer is used, and the connection with the Booster is
made simply with a single cable.

Safety Precautions
Use only 230V AC power supply. Using the Never let water come into contact with the
Booster with a different voltage power supply Booster and the Power Supply. Do not use
could cause fire or electrical shock. them in the bathroom and do not put medi-
cine or anything containing liquid on them.
Do not put the Booster and the Power Supply If water or medicine get into them, they will
in a poorly ventilated place. The Booster cause fire or electrical shock. Do not let your
Power Supply will overheat and may cause pets climb on them. If their urine or drop-
fire. Do not use in the following ways.... pings get into them, they will also cause fire
Pushing the Booster into a poorly ventilated or electrical shock.
place such as closet, bookcase or just under
a ceiling. Do not plug or unplug the Power Supply with
Covering with a table cloth. Placing on a wet hands. It may cause electrical shock.
carpet or bedding.
Covering or wrapping with a cloth or bedding.
Set the Power Supply at the place where you
When you hear thunder, don't touch any can easily unplug it.
lead-in cable from the TV antenna. It may
cause electrical shock.
When the Booster is not in use for a long
Use the Booster and Power Supply as one time, be sure to unplug the Power Supply
set. Using with other brands product may from the wall outlet for safety. Not doing so
cause fire. may cause fire.
1
To prevent mis-connection of the cables, check each port Input Mode Selector
connection closely. VHF/UHF Separated Input VHF/UHF Mixed Input
To keep each TV antenna at optimum performance, separate UHF VHF / UHF
them by 1 meter or more. Also be sure to separate the VHF
Booster from the antenna. When the span between the
antenna and the Booster is too short, oscillation (interference)
may result.
VHF/UHF
Antennas Be sure to put on the Weather
Boot(small size)provided with
VHF/UHF VHF/UHF this port when the cable is not
Separated Input Mixed Input
connected.
UHF

1m or more
VHF VHF / UHF Gain Controls
VHF High Band
1m or more 1m or more
Booster UHF
Gain Control
Maximum booster gain is reached when the
knobs are turned fully clockwise.
When the knob is turned fully clockwise and
you see beat (diagonal lines with random
Coaxial cable

Coaxial cable

Coaxial cable

motion) or wiper phenomenon(vertical bars


moving back and forth) on the screen (please
see photo on page 3), turn the appropriate
gain control knob counter-clockwise until it
disappears.
75

75

75

Total cable length is limited to approximately


Coaxial cable

100 meters from the Booster to the TV set,


with 75 Coaxial cable, type 5CFVA (sold
separately).

VHF/ UHF Mixed Input or UHF Input


Port connecting cable coming from VHF/UHF compatible If the Power Indicator remains light off...
75

antenna with a mixer or UHF antenna connection only. It is supposed the Power supply does not work properly.
VHF Input Unplug the Power supply and reconnect it and check the
Power indicator lights up after disconnecting the coaxial
Port connecting cable coming from VHF antenna only.
cable to the Antenna.
VHF / UHF

Be sure to put on the Weather boot (small size) provided


If the Power indicator lights up, there is probably a short
with this port when the cable is not connected.
circuit between the Power supply and the Antenna.
VHF/ UHF Mixed Output Then, the coaxial cable should be connected after resolving
Port connecting cable coming from any cause.
D
input port marked located on The Power supply may contain any failure if the Power
the Power supply Unit. indicator still remains light off.

230V AC AC power plug* must be


connected to the wall power
outlet after wiring and
Power Supply installation are completed.

*: An outlet Tap with surge


protector is recommended to
connect to the AC power plug
for safety use.
to Booster
VHF/UHF Input Plug Type : BF
[F-type (Female)]
The port connecting to TV
the cable coming from
Booster.
VHF / UHF
F-type(Male)
Output for TV set
Tightening torque Connection
0.8Nm (8.2kgfcm)
[IEC/PAL (Male)]

15V DC

VHF / UHF TV

2
Example How to Install the Booster
Required 4 TV Outlets Install the Booster on the mast in the outdoors.
(Installable on a wooden wall.)
VHF UHF VHF/UHF
To UHF (or VHF / UHF) antenna
Booster
VUB32LK2
To VHF antenna

Mast Fixing Clamp


Mast standoff
(Sold separately) Backing
plate
Applicable mast size:
VHF / UHF VHF / UHF 15V DC
22 - 48.6mm
Power Clamping Screw of Lid
15V DC Passing 4-way After closing the Lid, be
Port Splitter
sure to tighten the screw
as tightly as possible Mast
TV
with your fingers.
Tighten the wing nut firmly.
Wall outlet
(Power Insertion type)
TV TV TV To prevent rain from
Wall Wall Wall entering, wire the cable
Power supply outlet outlet outlet coming from the TV
antenna as illustrated.
230V AC
Mast standoff
TV (Sold separately)
To TV
(To Power supply)

When Better TV Picture Quality Cannot Be Obtained


When no picture or heavy snow noise interference is on the
TV screen, check the following :
The voltage of 11-16V DC is in active at the port marked located on the
Booster (Please refer to page2.).
The cables connection that is no breakage or short circuit in the wired cable.
The Input mode selectors setting position whether it is set in correct
position you required.
All bands (VHF High and UHF) input levels for the Booster reach 35dBV
Beat
or more from their TV antennas.
When Beat or Wiper interference Appears in the TV Picture.
(See photos right)
Make sure that the desired TV radio wave is not affected by the other
undesired radio waves. (At this time, there is no way to stop radio waves
undesired)
But interference may be improved little by adjusting the TV antennas
direction. Adjust TV antennas direction until the best possible TV picture is
obtained.
When the VHF/UHF input levels are more than 67dBV in each band, connect Wiper
an attenuator (ATT6, 10, 15, 20KFD, sold separately) to the input ports to avoid
such troubles shown right.

Correct Usage of the Booster


Improper use of the Booster might make a cause of trouble not only your own houses TV,
but also your nearby homes TV pictures.
Wiring of the Booster's Input and Output cables should be made correctly according to the instructions
described in this operating manual.
Do not tie up cables connecting input and output ports of the Booster, and also dont wind the cables over
the Booster case.
Be sure to use 75 Coaxial cable for all ports of the Booster.
When the Booster is installed on the TV antenna mast, it must be placed apart 1 meter or more from VHF
and UHF antennas.

3
Preparation Before Connecting Cable 8
12mm

Be sure to pass the cables through the Weather boots (large size) 4

braided wires
Fold Back the
before connecting the cables with the ports on the Booster
marked , and .(Please refer to page2.)
All cable ends connecting with the ports marked through
should be processed to measure as shown in the illustration right. (Cutting length is full scale)
To prevent incomplete contact or short circuit, install the plug with care.
F-type Connector Installation The included F-type connector is for 5C-type coaxial cables.

Cable processing Mounting the plug Attention to short circuit due to braided wires
(Cutting length is full scale.) 1. Pass the ferrule through the cable. Remove every debris, such as chips of the braided wires, in
2. Fold back the braided wires.
the connector shell. Even a piece of braid debris can cause
3. Push the plug into the cable firmy.
Cut off the tip of the short circuit when it touches the center conductor, then no
center conductor at picture appears on the TV screen.
an angle to prevent
incomplete contact. Fold back
Braided wires Center conductor

4 9mm Ferrule Braided Plug


wires

Pressure bonding of ferrule 1mm or less


Ferrule Completed
Press firmly at the foot of the plug so
that it does not come out.

Cable
Ferrule

Complete Drawing
Caution

MASter of PROduction
2mm Straighten the center conductor.
Make sure the length of the
center conductor is 2mm. A bent center conductor may cause short circuit and
malfunction.
If the center conductor extending from the
plug is longer than 4mm, the terminal part
of the F-type connector at the unit side will
be damaged and will cause malfunction.
Center conductor Center conductor

Specifications
VHF/UHF Booster Power Supply
Specifications Items Specifications
Items
VHF High Band UHF Primary Voltage 230V AC 50Hz
E ch.5 12 E ch.21 58 E ch.59 69 Power Consumption 3W
Reception Channels A ch.7 13 A ch.14 63 A ch.64 83 Secondary Voltage 15V DC
C ch.6 12 C ch.13 45 C ch.46 59 Secondary Current 75mA
Gain 25 31dB 26 35dB 22 33dB Frequency Range 167 806MHz 806 890MHz
Noise Figure 4.5dB or less (5dB or less, for Cch.6) 4dB or less Insertion Loss 2.5dB or less 3dB or less
0 10dB or more 0 10dB or more Temperature Range 0 + 40C
Gain Control Range
(Continuously Variable) (Continuously Variable) 106(H)x72(W)x65(D)mm
Dimensions
Operating Input Level 36.5 76dBV 36 69dBV (Except 1.8m Coaxial cable)
Maximum Output Level 107dBV 104dBV Weight Approx. 255g
VSWR (Voltage Standing Wave Ratio) 3 or less 4 or less(IN)
Input / Output Impedance 75 You can always rely on MASPROs performance data.
Power Requirements 15V DC 0.07A
Temperature Range 20 40C
2K56-620

Dimensions 130 (H) x 148 (W) x 64 (D) mm


Weight Approx. 290g

Specifications and external design are subject Accessories


LAB22-5620-3T

to change for further improvements. Weather Boot (large size) 3 pcs.


Weather Boot (small size) 1 pc.
F-type Connector (for 5C-type) 1 pc.

4 FEB., 2012

Das könnte Ihnen auch gefallen