Beruflich Dokumente
Kultur Dokumente
Est.Cost.Rs.
COLUMN PLAN FOR THE PROPOSED COMMUNITY HALL AT PO
C1 C2 C3 C4 C5
C8 C9
C11 C12
C6 C7
3.28
C10
4.90
C13
3.28
C19 C20
3.10 3.10
PLINTH PLAN FOR THE PROPOSED COMMUNITY HALL AT PO
'21 22 23 24 25
28 29
31 32
34 35 36 37 38
26 27
3.28
77 30
4.90
78 33
3.28
39 40
3.10 3.10
ROOF BEAM PLAN FOR THE PROPOSED COMMUNITY HALL AT
'41 42 43 44 45
48 49 61 63 65
51 52 62 64 66
54 55 56 57 58
46 47
3.28
67 50
4.90
68 53
3.28
59 60
3.10 3.10
DESIGN OF ROOF BEAM
Design Parametres:-
Design Parametres:-
Design Parametres:-
Effective depth provided 'd' in 'mm' 372 372 372 372 372
Actual depth of neutral axis 'xu' in 'mm' 24.68 122.4 122.4 24.68 30.39198076
Maximum depth of neutral axis 'xumax' in 178.56 178.56 178.56 178.56 178.56
'mm'
Area of steel required Ast in 'mm2' 113.2 561.38 561.38 113.2 139.4
Main Steel provided 2-16mm 2-16mm&1- 2-16mm&1- 2-16mm 2-12mm
20mm 20mm crank
crank
Side face reinforcement required in mm2 on 0 0 0 0 0
each face
Side face reinforcement provided on Nil Nil Nil Nil Nil
each face
Side face reinforcement provided in mm2 on 0 0 0 0 0
each face
Total Area of steel provided in 'mm2' 401.92 715.92 715.92 401.92 226.08
Percentage of steel provided pt 0.47 0.84 0.84 0.47 0.26
Equivalent shear force Ve in KN 48.45 87.45 87.45 48.45 32.95
Equivalent shear stress tve in N/sqmm 0.57 1.02 1.02 0.57 0.39
Max.shear strength of section tcmax in 2.8 2.8 2.8 2.8 2.8
N/sqmm
Design shear strength of section tc in 0.47 0.58 0.58 0.47 0.37
N/sqmm
Shear force Vus for which stirrups required 8.2368 37.8252 37.8252 8.2368 1.2928
in KN
Dia of Vertical two legged stirrups 8mm 8mm 8mm 8mm 8mm
assumed
Area of two legged vertical stirrups Asv in 100.48 100.48 100.48 100.48 100.48
mm2
Spacing required Sv in mm 450.84 282.07 282.07 450.84 591.5
Design Bond stress tbd in N/sqmm 1.92 1.92 1.92 1.92 1.92
Development length Ld in mm 752.19 752.19 752.19 752.19 752.19
(M1/V)+Lo 1657.682 1481.48 1481.48 1657.682 1406.496
Design Parametres:-
Effective depth provided 'd' in 'mm' 372 372 372 372 372
Actual depth of neutral axis 'xu' in 'mm' 53.8 0 0 0 35.74253768
Maximum depth of neutral axis 'xumax' in 178.56 178.56 178.56 178.56 178.56
'mm'
Area of steel required Ast in 'mm2' 246.77 0 0 0 163.94
Main Steel provided 2-16mm 2-16mm&2- 2-16mm&2- 2-16mm 2-16mm
16mm 16mm crank
crank
Side face reinforcement required in mm2 on 0 0 0 0 0
each face
Side face reinforcement provided on Nil Nil Nil Nil Nil
each face
Side face reinforcement provided in mm2 on 0 0 0 0 0
each face
Total Area of steel provided in 'mm2' 401.92 803.84 803.84 401.92 401.92
Percentage of steel provided pt 0.47 0.94 0.94 0.47 0.47
Equivalent shear force Ve in KN 29.66 0 0 0 18.56
Equivalent shear stress tve in N/sqmm 0.35 0 0 0 0.22
Max.shear strength of section tcmax in 2.8 2.8 2.8 2.8 2.8
N/sqmm
Design shear strength of section tc in 0.47 0.61 0.61 0.47 0.47
N/sqmm
Shear force Vus for which stirrups required -10.5532 -52.1916 -52.1916 -40.2132 -21.6532
in KN
Dia of Vertical two legged stirrups 8mm 8mm 8mm 8mm 8mm
assumed
Area of two legged vertical stirrups Asv in 100.48 100.48 100.48 100.48 100.48
mm2
Spacing required Sv in mm 960.54 #DIV/0! #DIV/0! #DIV/0! 1507.52
Design Bond stress tbd in N/sqmm 1.92 1.92 1.92 1.92 1.92
Development length Ld in mm 752.19 752.19 752.19 752.19 752.19
(M1/V)+Lo 2471.924 #DIV/0! #DIV/0! #DIV/0! 3878.095
Design Parametres:-
Concrete mix : M20
Steel : Fe415
Cover to Reinforcement : 40mm
Characteristic compressive strength of concrete = 20N/sqmm
Yield strength of steel = 415N/sqmm
Design Parametres:-
Effective depth provided 'd' in 'mm' 374 374 374 374 374
Actual depth of neutral axis 'xu' in 'mm' 16.9 70.6 70.6 16.9 30.54682995
Maximum depth of neutral axis 'xumax' in 179.52 179.52 179.52 179.52 179.52
'mm'
Area of steel required Ast in 'mm2' 77.53 323.82 323.82 77.53 140.11
Main Steel provided 2-12mm 2-12mm&1- 2-12mm&1- 2-12mm 2-12mm
16mm 16mm crank
crank
Side face reinforcement required in mm2 on 0 0 0 0 0
each face
Side face reinforcement provided on Nil Nil Nil Nil Nil
each face
Side face reinforcement provided in mm2 on 0 0 0 0 0
each face
Total Area of steel provided in 'mm2' 226.08 427.04 427.04 226.08 226.08
Percentage of steel provided pt 0.26 0.50 0.50 0.26 0.26
Equivalent shear force Ve in KN 53.65 77.25 77.25 53.65 46.75
Equivalent shear stress tve in N/sqmm 0.62 0.9 0.9 0.62 0.54
Max.shear strength of section tcmax in 2.8 2.8 2.8 2.8 2.8
N/sqmm
Design shear strength of section tc in 0.37 0.48 0.48 0.37 0.37
N/sqmm
Shear force Vus for which stirrups required 21.8226 35.9604 35.9604 21.8226 14.9226
in KN
Dia of Vertical two legged stirrups 8mm 8mm 8mm 8mm 8mm
assumed
Area of two legged vertical stirrups Asv in 100.48 100.48 100.48 100.48 100.48
mm2
Spacing required Sv in mm 256.88 213.39 213.39 256.88 273.16
Design Bond stress tbd in N/sqmm 1.92 1.92 1.92 1.92 1.92
Development length Ld in mm 564.14 564.14 564.14 564.14 564.14
(M1/V)+Lo 912.899 1080.664 1080.664 912.899 1006.993
Design Parametres:-
Design Parametres:-
Effective depth provided 'd' in 'mm' 377 377 527 527 377
Actual depth of neutral axis 'xu' in 'mm' 64.85 119.25 106.3 108.51 106.6460594
Maximum depth of neutral axis 'xumax' in 180.96 180.96 252.96 252.96 180.96
'mm'
Area of steel required Ast in 'mm2' 297.43 546.97 487.56 497.7 489.15
Main Steel provided 2-16mm 2-16mm&1- 2-16mm&1- 2- 2-16mm&1-
16mm 16mm extra 16mm&1- 16mm extra
extra 16mm
extra
Side face reinforcement required in mm2 on 0 0 66.125 66.125 0
each face
Side face reinforcement provided on Nil Nil Nil Nil Nil
each face
Side face reinforcement provided in mm2 on 0 0 0 0 0
each face
Total Area of steel provided in 'mm2' 401.92 602.88 602.88 602.88 602.88
Percentage of steel provided pt 0.46 0.70 0.50 0.50 0.70
Equivalent shear force Ve in KN 69.64 82.44 96.54 97.14 71.9
Equivalent shear stress tve in N/sqmm 0.8 0.95 0.8 0.8 0.83
Max.shear strength of section tcmax in 2.8 2.8 2.8 2.8 2.8
N/sqmm
Design shear strength of section tc in 0.46 0.54 0.48 0.48 0.54
N/sqmm
Shear force Vus for which stirrups required 29.7534 35.6166 38.3592 38.9592 25.0766
in KN
Dia of Vertical two legged stirrups 8mm 8mm 8mm 8mm 8mm
assumed
Area of two legged vertical stirrups Asv in 100.48 100.48 100.48 100.48 100.48
mm2
Spacing required Sv in mm 358.09 310.41 441.95 439.27 408.38
Design Bond stress tbd in N/sqmm 1.92 1.92 1.92 1.92 1.92
Development length Ld in mm 752.19 752.19 752.19 752.19 752.19
(M1/V)+Lo 1197.066 1371.721 1663.441 1652.001 1557.049
Design Parametres:-
Concrete mix : M20
Steel : Fe415
Cover to Reinforcement : 40mm
Characteristic compressive strength of concrete = 20N/sqmm
Yield strength of steel = 415N/sqmm
Design Parametres:-
Effective depth provided 'd' in 'mm' 527 527 377 377 527
Actual depth of neutral axis 'xu' in 'mm' 47.94 80.1 119.36 82.38 44.23072619
Maximum depth of neutral axis 'xumax' in 252.96 252.96 180.96 180.96 252.96
'mm'
Area of steel required Ast in 'mm2' 219.89 367.38 547.47 377.84 202.87
Main Steel provided 2-16mm+1- 2-16mm+1- 2-16mm+1- 2- 2-12mm+1-
16mm 16mm 16mm crank 16mm+1- 16mm crank
crank crank 16mm
crank
Side face reinforcement required in mm2 on 66.125 66.125 0 0 66.125
each face
Side face reinforcement provided on Nil Nil Nil Nil Nil
each face
Side face reinforcement provided in mm2 on 0 0 0 0 0
each face
Total Area of steel provided in 'mm2' 602.88 602.88 602.88 602.88 427.04
Percentage of steel provided pt 0.50 0.50 0.70 0.70 0.35
Equivalent shear force Ve in KN 53.42 62.22 83.23 74.63 40.22
Equivalent shear stress tve in N/sqmm 0.44 0.51 0.96 0.86 0.33
Max.shear strength of section tcmax in 2.8 2.8 2.8 2.8 2.8
N/sqmm
Design shear strength of section tc in 0.48 0.48 0.54 0.54 0.42
N/sqmm
Shear force Vus for which stirrups required -4.7608 4.0392 36.4066 27.8066 -10.6882
in KN
Dia of Vertical two legged stirrups 8mm 8mm 8mm 8mm 8mm
assumed
Area of two legged vertical stirrups Asv in 100.48 100.48 100.48 100.48 100.48
mm2
Spacing required Sv in mm 698.53 611.94 358.32 399.59 886.73
Design Bond stress tbd in N/sqmm 1.92 1.92 1.92 1.92 1.92
Development length Ld in mm 752.19 752.19 752.19 752.19 752.19
(M1/V)+Lo 2934.516 2493.348 1360.905 1547.858 2783.339
Design Parametres:-
Beam (39--
Item Beam (39--47) 47)
At Top At bottom
Distance from node at start 0.00m 4.19m 2.10m
Width of beam 'b' in 'm' 0.23 0.23 0.23
Depth of beam 'D' in 'm' 0.425 0.425 0.425
Dia.of bars assumed 16mm 16mm 16mm
Bending Moment Mu in KN-m 60 44.8 48
Shear force Vu in KN 88.4 81.1 42
Torsional Moment 'T' in KN-m 0.07 0.07 0.07
Equivalent bending moment Mt in KN-m 0.12 0.12 0.12
Design Moment Me1 in KN-m 60.12 44.92 48.12
Effective depth for balanced section in 'mm' 307.75 266.01 275.32
Design Parametres:-
Effective depth provided 'd' in 'mm' 527 527 377 377 527
Actual depth of neutral axis 'xu' in 'mm' 112.28 134.1 75.98 29.34 107.1420675
Maximum depth of neutral axis 'xumax' in 252.96 252.96 180.96 180.96 252.96
'mm'
Area of steel required Ast in 'mm2' 514.99 615.05 348.49 134.58 491.42
Main Steel provided 2-16mm+1- 2-16mm+1- 2-16mm+1- 2-16mm 2-12mm+1-
20mm 20mm 20mm crank 20mm crank
crank crank
Side face reinforcement required in mm2 on 66.125 66.125 0 0 66.125
each face
Side face reinforcement provided on Nil Nil Nil Nil Nil
each face
Side face reinforcement provided in mm2 on 0 0 0 0 0
each face
Total Area of steel provided in 'mm2' 715.92 715.92 715.92 401.92 540.08
Percentage of steel provided pt 0.59 0.59 0.83 0.46 0.45
Equivalent shear force Ve in KN 119.15 124.15 40.6 28.3 61.15
Equivalent shear stress tve in N/sqmm 0.98 1.02 0.47 0.33 0.5
Max.shear strength of section tcmax in 2.8 2.8 2.8 2.8 2.8
N/sqmm
Design shear strength of section tc in 0.51 0.51 0.58 0.46 0.46
N/sqmm
Shear force Vus for which stirrups required 57.3329 62.3329 -9.6918 -11.5866 5.3934
in KN
Dia of Vertical two legged stirrups 8mm 8mm 8mm 8mm 8mm
assumed
Area of two legged vertical stirrups Asv in 100.48 100.48 100.48 100.48 100.48
mm2
Spacing required Sv in mm 339.92 327.12 708.34 1000.45 622.34
Design Bond stress tbd in N/sqmm 1.92 1.92 1.92 1.92 1.92
Development length Ld in mm 752.19 752.19 752.19 752.19 752.19
(M1/V)+Lo 1602.861 1523.548 3105.739 2680.535 2247.713
Design Parametres:-
Effective depth provided 'd' in 'mm' 377 377 527 527 377
Actual depth of neutral axis 'xu' in 'mm' 67.57 102.76 60.53 63.08 93.69679252
Maximum depth of neutral axis 'xumax' in 180.96 180.96 252.96 252.96 180.96
'mm'
Area of steel required Ast in 'mm2' 309.92 471.32 277.65 289.31 429.75
Main Steel provided 2-16mm 2-16mm&1- 2-16mm&1- 2- 2-16mm&1-
16mm 16mm extra 16mm&1- 16mm extra
extra 16mm
extra
Side face reinforcement required in mm2 on 0 0 66.125 66.125 0
each face
Side face reinforcement provided on Nil Nil Nil Nil Nil
each face
Side face reinforcement provided in mm2 on 0 0 0 0 0
each face
Total Area of steel provided in 'mm2' 401.92 602.88 602.88 602.88 602.88
Percentage of steel provided pt 0.46 0.70 0.50 0.50 0.70
Equivalent shear force Ve in KN 68.71 77.21 48.28 48.98 71.83
Equivalent shear stress tve in N/sqmm 0.79 0.89 0.4 0.4 0.83
Max.shear strength of section tcmax in 2.8 2.8 2.8 2.8 2.8
N/sqmm
Design shear strength of section tc in 0.46 0.54 0.48 0.48 0.54
N/sqmm
Shear force Vus for which stirrups required 28.8234 30.3866 -9.9008 -9.2008 25.0066
in KN
Dia of Vertical two legged stirrups 8mm 8mm 8mm 8mm 8mm
assumed
Area of two legged vertical stirrups Asv in 100.48 100.48 100.48 100.48 100.48
mm2
Spacing required Sv in mm 386.85 348.45 891.21 878.6 392.98
Design Bond stress tbd in N/sqmm 1.92 1.92 1.92 1.92 1.92
Development length Ld in mm 752.19 752.19 752.19 752.19 752.19
(M1/V)+Lo 1206.764 1473.108 3189.368 3141.164 1579.747
Design Parametres:-
374
23.1413671
179.52
106.14
2-12mm
Nil
226.08
0.26
46.72
0.54
2.8
0.37
14.8926
8mm
100.48
356.08
1.92
564.14
1014.585
1--52--62--64--66--68--53)
At bottom
Remaining
0.23
0.42
16mm
16.8
41
3.52
5.85
22.65
188.89
372
38.43547365
178.56
176.29
2-16mm
Nil
0
401.92
0.47
65.49
0.77
2.8
0.47
25.2768
8mm
100.48
275.48
1.92
752.19
1274.663
-54)
At bottom
3.82m 5.73m
0.23 0.23
0.42 0.42
16mm 16mm
40.5 15.7
35 37
1.43 1.43
2.38 2.38
42.88 18.08
259.9 168.76
372 372
76.15462698 30.3919808
178.56 178.56
349.29 139.4
2-12mm+1- 2-12mm
20mm crank
0 0
Nil Nil
0 0
540.08 226.08
0.63 0.26
44.95 46.95
0.53 0.55
2.8 2.8
0.52 0.37
0.4588 15.2928
8mm 8mm
100.48 100.48
476.42 461.46
1.92 1.92
752.19 752.19
2167.113 1061.528
-55)
At bottom
3.82m 5.73m
0.23 0.23
0.42 0.42
16mm 16mm
0 0
0 0
0 0
372 372
0 0
178.56 178.56
0 0
2-16mm&2- 2-16mm
16mm crank
0 0
Nil Nil
0 0
803.84 401.92
0.94 0.47
0 0
0 0
2.8 2.8
0.61 0.47
-52.1916 -40.2132
8mm 8mm
100.48 100.48
#DIV/0! #DIV/0!
1.92 1.92
752.19 752.19
#DIV/0! #DIV/0!
-65--66--58 & 46--67--68--59)
At bottom
-60)
At bottom
3.54m 5.73m
0.23 0.23
0.42 0.42
12mm 12mm
22.6 9.01
20 8
5.57 5.57
9.26 9.26
31.86 18.27
224.03 169.65
374 374
54.81587759 30.5468299
179.52 179.52
251.42 140.11
2-12mm&1- 2-12mm
16mm crank
0 0
Nil Nil
0 0
427.04 226.08
0.50 0.26
58.75 46.75
0.68 0.54
2.8 2.8
0.48 0.37
17.4604 14.9226
8mm 8mm
100.48 100.48
246.04 273.16
1.92 1.92
564.14 564.14
1384.63 1006.993
-57)
At bottom
34--35)
14.10m
0.23
0.425
16mm
36
60.4
0.1
0.17
36.17
238.7
377
62.25327583
180.96
285.53
2-16mm
Nil
427.04
0.49
61.1
0.7
2.8
0.48
19.4792
8mm
100.48
479.22
1.92
752.19
1400.568
34--35)
-38)
At bottom
7.82m
0.23
0.425
16mm
34.3
40
0.004
0.01
34.31
232.48
377
58.8095354
180.96
269.74
2-12mm+1-
16mm crank
Nil
427.04
0.49
40.03
0.46
2.8
0.48
-1.5908
8mm
100.48
744.58
1.92
752.19
2013.635
-42)
At bottom
8.16m
0.23
0.425
16mm
13.3
23
0.13
0.22
13.52
145.94
377
22.20514583
180.96
101.85
2-12mm
Nil
226.08
0.26
23.9
0.28
2.8
0.37
-8.1827
8mm
100.48
1173.59
1.92
752.19
1882.036
45--46)
14.10m
0.23
0.425
16mm
39.4
63.4
0.35
0.59
39.99
250.99
377
69.42391613
180.96
318.42
2-16mm
Nil
401.92
0.46
65.83
0.76
2.8
0.46
25.9434
8mm
100.48
426.7
1.92
752.19
1246.401
45--46)
Roof Beam (41--42--43--44--45--46--47 & 54--55--56--57--58--59--60)
SECTION AT X--X
0.12
0.23
41 42 43 44 45 46
X
2-12mm dia
SECTION AT X--X
0.12
8mm dia 2 legged stirrups@ 150mm c/c
0.3 2-16mm dia bars
0.23
48 49 61 63 65 67
X
2-16mm dia
SECTION AT X--X
0.12
0.23
SECTION AT X--X
0.12
0.23
42 49 52 55
X
2-16mm dia
Roof Beam (43--61--62--56 , 44--63--64--57 , 45--65--66--58 & 46--67--68--59)
SECTION AT X--X
0.12
43 61 62 56
X 2-20mm dia
4-10mm dia bars
SECTION AT X--X
0.12
47 50 53 60
X
2-12mm dia
-60)
47
--53)
50
--68--59)
DESIGN OF TWO WAY SLAB:-
Design Parametres:-
Unit weight of RCC = 25KN/cum
Concrete mix : M20
Steel : Fe415
Cover to Reinforcement : 25mm
Characteristic compressive strength of concrete = 20N/sqmm
Yield strength of steel = 415N/sqmm
Item Slab panel Description
S1 S2
'41 42 43 44 45
48 49 61 63 65
54 55 56 57 58
46 47
3.28
67 50
4.90
68 53
3.28
59 60
3.10 3.10
DESIGN OF PLINTH BEAM
Design Parametres:-
Design Parametres:-
Design Parametres:-
Design Parametres:-
Effective depth provided 'd' in 'mm' 402 402 402 402 404
Actual depth of neutral axis 'xu' in 'mm' 17.18 87.79 87.79 17.18 25.92976446
Maximum depth of neutral axis 'xumax' in 192.96 192.96 192.96 192.96 193.92
'mm'
Area of steel required Ast in 'mm2' 78.79 402.64 402.64 78.79 118.93
Main Steel provided 2-12mm 2-12mm&1- 2-12mm&1- 2-12mm 2-12mm
16mm 16mm crank
crank
Side face reinforcement required in mm2 on 0 0 0 0 0
each face
Side face reinforcement provided on Nil Nil Nil Nil Nil
each face
Side face reinforcement provided in mm2 on 0 0 0 0 0
each face
Total Area of steel provided in 'mm2' 226.08 427.04 427.04 226.08 226.08
Percentage of steel provided pt 0.24 0.46 0.46 0.24 0.24
Equivalent shear force Ve in KN 44.43 75.53 75.53 44.43 26.93
Equivalent shear stress tve in N/sqmm 0.48 0.82 0.82 0.48 0.29
Max.shear strength of section tcmax in 2.8 2.8 2.8 2.8 2.8
N/sqmm
Design shear strength of section tc in 0.36 0.46 0.46 0.36 0.36
N/sqmm
Shear force Vus for which stirrups required 11.1444 32.9984 32.9984 11.1444 -6.5212
in KN
Dia of Vertical two legged stirrups 8mm 8mm 8mm 8mm 8mm
assumed
Area of two legged vertical stirrups Asv in 100.48 100.48 100.48 100.48 100.48
mm2
Spacing required Sv in mm 555.77 361.28 361.28 555.77 818.85
Design Bond stress tbd in N/sqmm 1.92 1.92 1.92 1.92 1.92
Development length Ld in mm 752.19 752.19 752.19 752.19 564.14
(M1/V)+Lo 1192.477 1218.555 1218.555 1192.477 1736.189
Design Parametres:-
Effective depth provided 'd' in 'mm' 404 404 404 404 404
Actual depth of neutral axis 'xu' in 'mm' 29.86 39.69 39.69 29.86 40.99866848
Maximum depth of neutral axis 'xumax' in 193.92 193.92 193.92 193.92 193.92
'mm'
Area of steel required Ast in 'mm2' 136.98 182.06 182.06 136.98 188.05
Main Steel provided 2-12mm 2-12mm&1- 2-12mm&1- 2-12mm 3-12mm
12mm 12mm extra
extra
Side face reinforcement required in mm2 on 0 0 0 0 0
each face
Side face reinforcement provided on Nil Nil Nil Nil Nil
each face
Side face reinforcement provided in mm2 on 0 0 0 0 0
each face
Total Area of steel provided in 'mm2' 226.08 339.12 339.12 226.08 339.12
Percentage of steel provided pt 0.24 0.36 0.36 0.24 0.36
Equivalent shear force Ve in KN 66.43 70.13 70.13 66.43 46.43
Equivalent shear stress tve in N/sqmm 0.71 0.75 0.75 0.71 0.5
Max.shear strength of section tcmax in 2.8 2.8 2.8 2.8 2.8
N/sqmm
Design shear strength of section tc in 0.36 0.42 0.42 0.36 0.42
N/sqmm
Shear force Vus for which stirrups required 32.9788 31.1036 31.1036 32.9788 7.4036
in KN
Dia of Vertical two legged stirrups 8mm 8mm 8mm 8mm 8mm
assumed
Area of two legged vertical stirrups Asv in 100.48 100.48 100.48 100.48 100.48
mm2
Spacing required Sv in mm 314.12 303.27 303.27 314.12 389.49
Design Bond stress tbd in N/sqmm 1.92 1.92 1.92 1.92 1.92
Development length Ld in mm 564.14 564.14 564.14 564.14 564.14
(M1/V)+Lo 812.513 1066.312 1066.312 812.513 1513.161
Design Parametres:-
252
34.90803103
120.96
160.11
2-16mm
Nil
401.92
0.69
33.23
0.57
2.8
0.54
1.9316
8mm
100.48
384.7
1.92
752.19
1596.972
1--32)
At bottom
1.94m
0.23
0.3
16mm
23
26.5
0.76
1.03
24.03
194.56
252
64.52110379
120.96
295.93
2-16mm&1-
12mm crank
Nil
0
514.96
0.89
31.79
0.55
2.8
0.60
-2.986
8mm
100.48
454.83
1.92
752.19
1959.555
8--33)
At bottom
1.94m
0.23
0.3
12mm
4.7
8.9
2.83
3.84
8.54
115.99
254
21.03480005
121.92
96.48
2-12mm
0
Nil
226.08
0.39
28.59
0.49
2.8
0.43
3.4694
8mm
100.48
313.53
1.92
564.14
1097.148
7--30--33--40)
At bottom
3.82m 5.73m
0.23 0.23
0.45 0.45
12mm 12mm
31.7 14.9
32 32
1.14 1.14
1.98 1.98
33.68 16.88
230.34 163.07
404 404
53.29481684 25.9297645
193.92 193.92
244.44 118.93
2-12mm&1- 2-12mm
16mm crank
0 0
Nil Nil
0 0
427.04 226.08
0.46 0.24
39.93 39.93
0.43 0.43
2.8 2.8
0.46 0.36
-2.8132 6.4788
8mm 8mm
100.48 100.48
616.67 616.67
1.92 1.92
564.14 564.14
2102.802 1231.893
-35)
At bottom
3.82m 5.73m
0.23 0.23
0.45 0.45
12mm 12mm
3.06 20.5
23.4 23.4
3.31 3.31
5.76 5.76
8.82 26.26
117.87 203.39
404 404
13.36919763 40.9986685
193.92 193.92
61.32 188.05
3-12mm 3-12mm
0 0
Nil Nil
0 0
339.12 339.12
0.36 0.36
46.43 46.43
0.5 0.5
2.8 2.8
0.42 0.42
7.4036 7.4036
8mm 8mm
100.48 100.48
389.49 389.49
1.92 1.92
564.14 564.14
1552.941 1513.161
-38 , 26--39)
At bottom
Plinth Beam (21--22--23--24--25--26--27 & 34--35--36--37--38--39--40)
SECTION AT X--X
0.23
21 22 23 24 25 26
X
2-16mm dia
SECTION AT X--X
0.23
1-12mm crank
2-16mm dia
X
28 29
X
2-16mm dia
SECTION AT X--X
0.23
2-16mm dia
X
28 29
X
2-12mm dia
SECTION AT X--X
0.23
21 28 31 34
X
2-12mm dia
Plinth Beam (22--29--32--35)
SECTION AT X--X
0.23
22 29 32 35
X
3-12mm dia
SECTION AT X--X
2-20mm dia
X
23 36
X
2-12mm dia
-40)
27
DESIGN OF COLUMNS
Design Parametres:-
Concrete mix : M20
Steel : Fe415
Cover to Reinforcement d' : 40mm
Unit weight of RCC = 25KN/cum
Characteristic compressive strength of concrete = 20N/sqmm
Yield strength of steel = 415N/sqmm
Item Column 1 Column 2
1st storey 2nd storey 3rd storey 1st storey 2nd storey 3rd storey
Axial load Pu (KN) 227.57 131.4 37.79 311.66 163.78 39.91
Moment about 'y' axis My(KN- 4.75 5.8 6.91 6.25 7.24 8.31
m)
Moment about 'z' axis Mz(KN- 14.92 16.85 14.75 5.92 7.24 15.51
m)
Eccentricity about 'y' axis in 20.87 44.14 182.85 20.05 44.21 208.22
'mm'
Eccentricity about 'z' axis in 65.56 128.23 390.31 19 44.21 388.62
'mm'
Moment about 'y' axis My(KN- 4.75 5.8 6.91 6.25 7.24 8.31
m) for Min.Eccentricity
Moment about 'z' axis Mz(KN- 14.92 16.85 14.75 6.23 7.24 15.51
m) for Min.Eccentricity
Design moment Muz in KN-m 14.92 16.85 14.75 6.23 7.24 15.51
d'/D about 'y' axis 0.17 0.17 0.17 0.17 0.17 0.17
d'/D about 'z' axis 0.13 0.13 0.13 0.13 0.13 0.13
Pu/fckbD 0.165 0.095 0.027 0.226 0.119 0.029
p/fck 0.058 0.058 0.058 0.058 0.058 0.058
Muy1/fckbd2 from SP-16 0.09 0.095 0.085 0.09 0.095 0.085
Muz1/fckbd2 from SP-16 0.08 0.09 0.08 0.095 0.1 0.09
Max.moment carrying 28.57 30.15 26.98 28.57 30.15 26.98
capacity for uniaxial bending
about 'y' axis Muy1
Max.moment carrying 33.12 37.26 33.12 39.33 41.4 37.26
capacity for uniaxial bending
about 'z' axis Muz1
Max.axial load capacity Puz 862.92 862.92 862.92 862.92 862.92 862.92
Pu/Puz 0.26 0.15 0.04 0.36 0.19 0.05
an 1.10 1.00 1.00 1.27 1.00 1.00
(Muy/Muy1)an + (Muz/Muz1)an 0.55 0.74 0.7 0.24 0.54 0.72
Area of steel Required in mm2 800.40 800.40 800.40 800.40 800.40 800.40
Spacing of 8mm ties in 'mm' 190 190 190 190 190 190
Reinforcement provided 4-16 4-16 4-16 4-16 4-16 4-16
Area of steel provideded in 803.84 803.84 803.84 803.84 803.84 803.84
mm2
DESIGN OF COLUMNS
Design Parametres:-
Concrete mix : M20
Steel : Fe415
Cover to Reinforcement d' : 40mm
Unit weight of RCC = 25KN/cum
Characteristic compressive strength of concrete = 20N/sqmm
Yield strength of steel = 415N/sqmm
Item Column 4 Column 5
1st storey 2nd storey 1st storey 2nd storey
Axial load Pu (KN) 358.31 213.55 358.63 213.33
Moment about 'y' axis My(KN- 18.32 255.44 18.6 256.46
m)
Moment about 'z' axis Mz(KN- 0.81 0.4 0.12 1.59
m)
Eccentricity about 'y' axis in 51.13 1196.16 51.86 1202.18
'mm'
Eccentricity about 'z' axis in 2.26 1.87 0.33 7.45
'mm'
Moment about 'y' axis My(KN- 18.32 255.44 18.6 256.46
m) for Min.Eccentricity
Moment about 'z' axis Mz(KN- 7.17 4.27 7.17 4.27
m) for Min.Eccentricity
Moment about 'z' axis Mz(KN- 8.4 8.12 15.72 14.88 14.74
m) for Min.Eccentricity
DESIGN OF COLUMNS
Design Parametres:-
Concrete mix : M20
Steel : Fe415
Cover to Reinforcement d' : 40mm
Unit weight of RCC = 25KN/cum
Characteristic compressive strength of concrete = 20N/sqmm
Yield strength of steel = 415N/sqmm
Item Column 10 Column 11
1st storey 2nd storey 1st storey 2nd storey 3rd storey
Axial load Pu (KN) 250.84 102.23 467.54 283.77 86.05
Moment about 'y' axis My(KN- 6.47 7.55 5.77 9.1 11.92
m)
Moment about 'z' axis Mz(KN- 8.09 19.36 15.72 14.88 14.74
m)
Eccentricity about 'y' axis in 25.79 73.85 12.34 32.07 138.52
'mm'
Eccentricity about 'z' axis in 32.25 189.38 33.62 52.44 171.3
'mm'
Moment about 'y' axis My(KN- 6.47 7.55 9.35 9.1 11.92
m) for Min.Eccentricity
Moment about 'z' axis Mz(KN- 8.09 19.36 15.72 14.88 14.74
m) for Min.Eccentricity
DESIGN OF COLUMNS
Design Parametres:-
Concrete mix : M20
Steel : Fe415
Cover to Reinforcement d' : 40mm
Unit weight of RCC = 25KN/cum
Characteristic compressive strength of concrete = 20N/sqmm
Yield strength of steel = 415N/sqmm
Item Column 13 Column 14
1st storey 2nd storey 1st storey 2nd storey 3rd storey
Axial load Pu (KN) 250.84 102.23 227.57 131.4 37.79
Moment about 'y' axis My(KN- 6.47 7.55 4.75 5.8 6.91
m)
Moment about 'z' axis Mz(KN- 8.09 19.36 14.92 16.85 14.75
m)
Eccentricity about 'y' axis in 25.79 73.85 20.87 44.14 182.85
'mm'
Eccentricity about 'z' axis in 32.25 189.38 65.56 128.23 390.31
'mm'
Moment about 'y' axis My(KN- 6.47 7.55 4.75 5.8 6.91
m) for Min.Eccentricity
Moment about 'z' axis Mz(KN- 8.09 19.36 14.92 16.85 14.75
m) for Min.Eccentricity
DESIGN OF COLUMNS
Design Parametres:-
Concrete mix : M20
Steel : Fe415
Cover to Reinforcement d' : 40mm
Unit weight of RCC = 25KN/cum
Characteristic compressive strength of concrete = 20N/sqmm
Yield strength of steel = 415N/sqmm
Item Column 16 Column 17
1st storey 2nd storey 1st storey 2nd storey 3rd storey
Axial load Pu (KN) 341.43 184.77 358.32 213.55
Moment about 'y' axis My(KN- 12.7 212.52 18.32 255.45
m)
Moment about 'z' axis Mz(KN- 0.5 9.8 0.9 0.4
m)
Eccentricity about 'y' axis in 37.2 1150.19 51.13 1196.21
'mm'
Eccentricity about 'z' axis in 1.46 53.04 2.51 1.87
'mm'
Moment about 'y' axis My(KN- 12.7 212.52 18.32 255.45
m) for Min.Eccentricity
DESIGN OF COLUMNS
Design Parametres:-
Concrete mix : M20
Steel : Fe415
Cover to Reinforcement d' : 40mm
Unit weight of RCC = 25KN/cum
Characteristic compressive strength of concrete = 20N/sqmm
Yield strength of steel = 415N/sqmm
Item Column 19 Column 20
1st storey 2nd storey 1st storey 2nd storey
Axial load Pu (KN) 359.18 198.66 113.38 30.24
Moment about 'y' axis My(KN- 12.53 226.35 3.96 4.31
m)
Moment about 'z' axis Mz(KN- 1.26 4.92 8.4 8.12
m)
Eccentricity about 'y' axis in 34.89 1139.38 34.93 142.53
'mm'
Eccentricity about 'z' axis in 3.51 24.77 74.09 268.52
'mm'
Moment about 'y' axis My(KN- 12.53 226.35 3.96 4.31
m) for Min.Eccentricity
0.5 9.8
37.2 1150.46
1.46 53.04
12.7 212.57
6.83 9.8
1.95 4
1.95 4
0.6 0.6
0.3 0.3
1.56 3.2
1.56 3.2
2.6 5.33
5.2 10.67
1.59 1.59
0 0
0 0
12.7 212.57
6.83 9.8
0.07 0.07
0.13 0.13
0.095 0.051
0.0795 0.0795
0.097 0.12
0.09 0.11
209.52 259.2
97.2 118.8
2485.04 2485.04
0.14 0.07
1.00 1.00
0.13 0.9
2862.00 2862.00
190 190
4-20&8-16 4-20&8-16
2863.68 2863.68
Column 6
1st storey 2nd storey
359.18 198.66
12.53 226.35
1.3 4.92
34.89 1139.38
3.62 24.77
12.53 226.35
7.18 4.92
1.95 4
1.95 4
0.6 0.6
0.3 0.3
1.56 3.2
1.56 3.2
2.6 5.33
5.2 10.67
1.59 1.59
0 0
0 0
12.53 226.35
7.18 4.92
0.07 0.07
0.13 0.13
0.1 0.055
0.0795 0.0795
0.13 0.12
0.12 0.11
280.8 259.2
129.6 118.8
2485.04 2485.04
0.14 0.08
1.00 1.00
0.1 0.91
2862.00 2862.00
190 190
4-20&8-16 4-20&8-16
2863.68 2863.68
Column 9
1st storey 2nd storey 3rd storey
498.41 375.53 78.31
4.96 9.62 11.75
1.95 4 3.35
1.95 4 3.35
0 0 0
9.97 17.98 11.75
Column 12
1st storey 2nd storey 3rd storey
498.41 375.53 78.31
4.96 9.62 11.75
1.95 4 3.35
1.95 4 3.35
0 0 0
Column 15
1st storey 2nd storey 3rd storey
311.66 163.78 39.91
6.25 7.24 8.31
19 44.21 388.62
1.95 4 3.35
1.95 4 3.35
0 0 0
Column 18
1st storey 2nd storey 3rd storey
358.37 213.33
18.61 256.46
0.12 1.59
51.93 1202.18
0.33 7.45
18.61 256.46
7.17 4.27
1.95 4
1.95 4
0.6 0.6
0.3 0.3
1.56 3.2
1.56 3.2
2.6 5.33
5.2 10.67
1.59 1.59
0 0
0 0
18.61 256.46
7.17 4.27
0.07 0.07
0.13 0.13
0.1 0.059
0.0795 0.0795
0.13 0.125
0.12 0.11
280.8 270
129.6 118.8
2485.04 2485.04
0.14 0.09
1.00 1.00
0.12 0.99
2862.00 2862.00
190 190
4-20&8-16 4-20&8-16
2863.68 2863.68
DESIGN OF FOOTING
Design Parametres:-
Footing designation = F1
Concrete mix M20
Steel Fe415
Cover to Reinforcement 40mm
Safe Bearing Capacity(From soil Report)= 98.00KN/sqm
Unit weight of RCC = 25.0KN/cum
Width of Column b = 0.23m
Depth of Column d = 0.30m
Characteristic compressive strength of concrete = 20.00N/sqmm
Yield strength of steel = 415.00N/sqmm
Load calculations:-
The net ultimate bearing pressure acting on the footing due to direct load = 82.04KN/sqm
substituting the above value and finding out the effective depth by solving the above
equation,
11112055.4 11110000
d= 63.46mm
Assuming 40mm effective cover and 8mm dia bars,the over all depth comes to
107.46mm
However provide over all depth of 250mm and the effective depth is 206mm
The critical section for beam shear is at distance of 'd' from the face of the column
The design shear strength of concrete for the above steel percentage from
Table 19 of IS 456 is
0.50 N/sqmm Hence Vuc = 103.00KN
0.50>0.13
The critical section for two-way shear is along the perphery of the square at a
distance d/2 from the face of the column
Tc' =ks . Tc
ks = (0.5+l/b)> 1
Hence ks = 1
1.12>0.27
11188187.5753 11110000N-mm
The actual depth of neutral axis is less than the X umax.Hence,the section remains
under reinforced.
Hence Safe
Design Parametres:-
Footing designation = F2
Concrete mix M20
Steel Fe415
Cover to Reinforcement 40mm
Safe Bearing Capacity(From soil Report)= 98.00KN/sqm
Unit weight of RCC = 25.0KN/cum
Width of Column b = 0.23m
Depth of Column d = 0.30m
Characteristic compressive strength of concrete = 20.00N/sqmm
Yield strength of steel = 415.00N/sqmm
Load calculations:-
The net ultimate bearing pressure acting on the footing due to direct load = 113.33KN/sqm
substituting the above value and finding out the effective depth by solving the above
equation,
24620119 24580000
d= 94.46mm
Assuming 40mm effective cover and 8mm dia bars,the over all depth comes to
138.46mm
However provide over all depth of 250mm and the effective depth is 206mm
The critical section for beam shear is at distance of 'd' from the face of the column
The design shear strength of concrete for the above steel percentage from
Table 19 of IS 456 is
0.50 N/sqmm Hence Vuc = 103.00KN
0.50>0.25
The critical section for two-way shear is along the perphery of the square at a
distance d/2 from the face of the column
Hence perimetre of the preriphery b0 = 2260mm
Permissible shear stress in concrete for two-way shear for M20 grade concrete
Tc' =ks . Tc
ks = (0.5+l/b)> 1
Hence ks = 1
1.12>0.53
24620557.336 24580000N-mm
The actual depth of neutral axis is less than the X umax.Hence,the section remains
under reinforced.
Hence Safe
Design Parametres:-
Footing designation = F3
Concrete mix M20
Steel Fe415
Cover to Reinforcement 40mm
Safe Bearing Capacity(From soil Report)= 98.00KN/sqm
Unit weight of RCC = 25.0KN/cum
Width of Column b = 0.30m
Depth of Column d = 0.60m
Characteristic compressive strength of concrete = 20.00N/sqmm
Yield strength of steel = 415.00N/sqmm
Load calculations:-
The net ultimate bearing pressure acting on the footing due to direct load = 114.44KN/sqm
substituting the above value and finding out the effective depth by solving the above
equation,
35897235 35790000
d= 114.06mm
Assuming 40mm effective cover and 8mm dia bars,the over all depth comes to
158.06mm
However provide over all depth of 300mm and the effective depth is 256mm
The critical section for beam shear is at distance of 'd' from the face of the column
The design shear strength of concrete for the above steel percentage from
Table 19 of IS 456 is
0.50 N/sqmm Hence Vuc = 128.00KN
0.50>0.25
The critical section for two-way shear is along the perphery of the square at a
distance d/2 from the face of the column
Hence perimetre of the preriphery b0 = 4200mm
Permissible shear stress in concrete for two-way shear for M20 grade concrete
Tc' =ks . Tc
ks = (0.5+l/b)> 1
Hence ks = 1
1.12>0.36
35521769.5907 35790000N-mm
The actual depth of neutral axis is less than the X umax.Hence,the section remains
under reinforced.
Hence Safe
Design Parametres:-
Footing designation = F4
Concrete mix M20
Steel Fe415
Cover to Reinforcement 40mm
Safe Bearing Capacity(From soil Report)= 98.00KN/sqm
Unit weight of RCC = 25.0KN/cum
Width of Column b = 0.23m
Depth of Column d = 0.30m
Characteristic compressive strength of concrete = 20.00N/sqmm
Yield strength of steel = 415.00N/sqmm
Load calculations:-
The net ultimate bearing pressure acting on the footing due to direct load = 155.56KN/sqm
substituting the above value and finding out the effective depth by solving the above
equation,
50855499 50830000
d= 135.76mm
Assuming 40mm effective cover and 8mm dia bars,the over all depth comes to
179.76mm
However provide over all depth of 300mm and the effective depth is 256mm
The critical section for beam shear is at distance of 'd' from the face of the column
The design shear strength of concrete for the above steel percentage from
Table 19 of IS 456 is
0.50 N/sqmm Hence Vuc = 128.00KN
0.50>0.34
The critical section for two-way shear is along the perphery of the square at a
distance d/2 from the face of the column
Hence perimetre of the preriphery b0 = 2260mm
Permissible shear stress in concrete for two-way shear for M20 grade concrete
Tc' =ks . Tc
ks = (0.5+l/b)> 1
Hence ks = 1
1.12>0.86
51114710.6339 50830000N-mm
The actual depth of neutral axis is less than the X umax.Hence,the section remains
under reinforced.
Hence Safe
0.23
Columns C3,C4,C5,C6,C16,C17,C18,C19
0.3
Footing---F1(7,20)
0.25m
1.2m
0.25m
1.5m
0.3m
1.8m
0.3m
1.8m