Beruflich Dokumente
Kultur Dokumente
WELINTON TAPUY
DENNY DAMIAN
KARINA LESANO
CAROLINA ATI
JOFFRE CABRERA
STALIN SALTOS
EDWIN MORALES
2017 Cisco and/or its affiliates. All rights reserved. This document is Cisco Public. Page 1 of 13
Lab - Configuring Multiarea OSPFv3
Topology
++||
2017 Cisco and/or its affiliates. All rights reserved. This document is Cisco Public. Page 2 of 13
Lab - Configuring Multiarea OSPFv3
Addressing Table
2001:DB8:ACAD:12::1/64
R1 S0/0/0 (DCE)
FE80::1 link-local N/A
Lo0 2001:DB8:ACAD::1/64 N/A
Lo1 2001:DB8:ACAD:1::1/64 N/A
Lo2 2001:DB8:ACAD:2::1/64 N/A
Lo3 2001:DB8:ACAD:3::1/64 N/A
2001:DB8:ACAD:12::2/64
R2 S0/0/0
FE80::2 link-local N/A
2001:DB8:ACAD:23::2/64
S0/0/1 (DCE)
FE80::2 link-local N/A
Lo8 2001:DB8:ACAD:8::1/64 N/A
2001:DB8:ACAD:23::3/64
R3 S0/0/1
FE80::3 link-local N/A
Lo4 2001:DB8:ACAD:4::1/64 N/A
Lo5 2001:DB8:ACAD:5::1/64 N/A
Lo6 2001:DB8:ACAD:6::1/64 N/A
Lo7 2001:DB8:ACAD:7::1/64 N/A
Objectives
Part 1: Build the Network and Configure Basic Device Settings
Part 2: Configure Multiarea OSPFv3 Routing
Part 3: Configure Interarea Route Summarization
Background / Scenario
Using multiarea OSPFv3 in large IPv6 network deployments can reduce router processing by creating smaller
routing tables and requiring less memory overhead. In multiarea OSPFv3, all areas are connected to the
backbone area (area 0) through area border routers (ABRs).
In this lab, you will implement OSPFv3 routing for multiple areas and configure interarea route
summarizations on the Area Border Routers (ABRs). You will also use a number of show commands to
display and verify OSPFv3 routing information. This lab uses loopback addresses to simulate networks in
multiple OSPFv3 areas.
Note: The routers used with CCNA hands-on labs are Cisco 1941 Integrated Services Routers (ISRs) with
Cisco IOS Release 15.2(4)M3 (universalk9 image). Other routers and Cisco IOS versions can be used.
Depending on the model and Cisco IOS version, the commands available and output produced might vary
from what is shown in the labs. Refer to the Router Interface Summary Table at this end of this lab for the
correct interface identifiers.
Note: Make sure that the routers have been erased and have no startup configurations. If you are unsure,
contact your instructor.
2017 Cisco and/or its affiliates. All rights reserved. This document is Cisco Public. Page 3 of 13
Lab - Configuring Multiarea OSPFv3
Required Resources
3 Routers (Cisco 1941 with Cisco IOS Release 15.2(4)M3 universal image or comparable)
3 PCs (Windows 7, Vista, or XP with terminal emulation program, such as Tera Term)
Console cables to configure the Cisco IOS devices via the console ports
Serial cables as shown in the topology
2017 Cisco and/or its affiliates. All rights reserved. This document is Cisco Public. Page 4 of 13
Lab - Configuring Multiarea OSPFv3
d. Issue the show ipv6 ospf command to verify the router IDs on all routers.
R2# show ipv6 ospf
Routing Process "ospfv3 1" with ID 2.2.2.2
Event-log enabled, Maximum number of events: 1000, Mode: cyclic
Router is not originating router-LSAs with maximum metric
<output omitted>
2017 Cisco and/or its affiliates. All rights reserved. This document is Cisco Public. Page 5 of 13
Lab - Configuring Multiarea OSPFv3
c. Assign all interfaces on R2 to participate in OSPFv3 area 0. For the loopback interface, change the
network type to point-to point. Write the commands used in the space below.
R2(config)#
interface lo8
R2(config-if)#
ipv6 ospf 1 area 0
R2(config-if)#
ipv6 ospf network point-to-point
R2(config-if)#
interface s0/0/0
R2(config-if)#
ipv6 ospf 1 area 0
R2(config-if)#
interface s0/0/1
R2(config-if)#
ipv6 ospf 1 area 0
d. Use the show ipv6 ospf interface brief command to view OSPFv3 enabled interfaces.
R2# show ipv6 ospf interface brief
Interface PID Area Intf ID Cost State Nbrs F/C
Lo8 1 0 13 1 P2P 0/0
Se0/0/1 1 0 7 64 P2P 1/1
Se0/0/0 1 0 6 64 P2P 1/1
e. Assign the loopback interfaces on R3 to participate in OSPFv3 area 2 and change the network type to
point-to-point. Assign the serial interface to participate in OSPFv3 area 0. Write the commands used in
the space below.
R3(config)#
interface lo4
R3(config-if)#
ipv6 ospf 1 area 2
R3(config-if)#
ipv6 ospf network point-to-point
R3(config-if)#
interface lo5
R3(config-if)#
ipv6 ospf 1 area 2
R3(config-if)#
ipv6 ospf network point-to-point
R3(config-if)#
interface lo6
R3(config-if)#
ipv6 ospf 1 area 2
R3(config-if)#
ipv6 ospf network point-to-point
R3(config-if)#
2017 Cisco and/or its affiliates. All rights reserved. This document is Cisco Public. Page 6 of 13
Lab - Configuring Multiarea OSPFv3
interface lo7
R3(config-if)#
ipv6 ospf 1 area 2
R3(config-if)#
ipv6 ospf network point-to-point
R3(config-if)#
interface s0/0/1
R3(config-if)#
ipv6 ospf 1 area 0
2017 Cisco and/or its affiliates. All rights reserved. This document is Cisco Public. Page 7 of 13
Lab - Configuring Multiarea OSPFv3
2017 Cisco and/or its affiliates. All rights reserved. This document is Cisco Public. Page 8 of 13
Lab - Configuring Multiarea OSPFv3
2017 Cisco and/or its affiliates. All rights reserved. This document is Cisco Public. Page 9 of 13
Lab - Configuring Multiarea OSPFv3
2017 Cisco and/or its affiliates. All rights reserved. This document is Cisco Public. Page 10 of 13
Lab - Configuring Multiarea OSPFv3
2017 Cisco and/or its affiliates. All rights reserved. This document is Cisco Public. Page 11 of 13
Lab - Configuring Multiarea OSPFv3
b. Manually configure interarea route summarization on R3. Write the commands in the space provided.
Reflection
1. Why would multiarea OSPFv3 be used?
Multiarea OSPFv3 puede ser usado en grandes dominios de red para mejorar la eficiencia del proceso de
enrutamiento, disminuir el tamao de las tablas de enrutamiento del router y disminuir las necesidades de
procesamiento de CPU/memoria
CONCLUSION
Al establecer ospf multiarea es obligatorio configurar un area de backbone en la cual estarn conectadas las
demas areas El diseo de areas en ospf nos permite tener mayor escabilidad en la red. a mas de la ventaja
de mejorar el proceso de ruteo.
2017 Cisco and/or its affiliates. All rights reserved. This document is Cisco Public. Page 12 of 13
Lab - Configuring Multiarea OSPFv3
Router Model Ethernet Interface #1 Ethernet Interface #2 Serial Interface #1 Serial Interface #2
1800 Fast Ethernet 0/0 Fast Ethernet 0/1 Serial 0/0/0 (S0/0/0) Serial 0/0/1 (S0/0/1)
(F0/0) (F0/1)
1900 Gigabit Ethernet 0/0 Gigabit Ethernet 0/1 Serial 0/0/0 (S0/0/0) Serial 0/0/1 (S0/0/1)
(G0/0) (G0/1)
2801 Fast Ethernet 0/0 Fast Ethernet 0/1 Serial 0/1/0 (S0/1/0) Serial 0/1/1 (S0/1/1)
(F0/0) (F0/1)
2811 Fast Ethernet 0/0 Fast Ethernet 0/1 Serial 0/0/0 (S0/0/0) Serial 0/0/1 (S0/0/1)
(F0/0) (F0/1)
2900 Gigabit Ethernet 0/0 Gigabit Ethernet 0/1 Serial 0/0/0 (S0/0/0) Serial 0/0/1 (S0/0/1)
(G0/0) (G0/1)
Note: To find out how the router is configured, look at the interfaces to identify the type of router and how many
interfaces the router has. There is no way to effectively list all the combinations of configurations for each router
class. This table includes identifiers for the possible combinations of Ethernet and Serial interfaces in the device.
The table does not include any other type of interface, even though a specific router may contain one. An
example of this might be an ISDN BRI interface. The string in parenthesis is the legal abbreviation that can be
used in Cisco IOS commands to represent the interface.
2017 Cisco and/or its affiliates. All rights reserved. This document is Cisco Public. Page 13 of 13