Beruflich Dokumente
Kultur Dokumente
Title page
Alcatel-Lucent 9353
Wireless Management System | UA08.1
Activation of MC-RRH
9YZ-03450-3547-PGZZA
Issue 2 | January 2013
Alcatel-Lucent Proprietary
Use pursuant to applicable agreements
Use pursuant to applicable agreements
Legal notice
Legal notice
Alcatel, Lucent, Alcatel-Lucent and the Alcatel-Lucent logo are trademarks of Alcatel-Lucent. All other trademarks are the property of their respective
owners.
The information presented is subject to change without notice. Alcatel-Lucent assumes no responsibility for inaccuracies contained herein.
Copyright 2013 Alcatel-Lucent. All rights reserved.
Contains proprietary/trade secret information which is the property of Alcatel-Lucent and must not be made available to, or copied or used by anyone outside
Alcatel-Lucent without its written authorization.
Not to be used or disclosed except in accordance with applicable agreements.
Alcatel-Lucent Proprietary
Use pursuant to applicable agreements
Contents
2 MC-RRH overview
MC-RRH architecture
....................................................................................................................................................................................................................................
Alcatel-Lucent 9353 WMS Alcatel-Lucent Proprietary iii
9YZ-03450-3547-PGZZA UA08.1 Use pursuant to applicable agreements
Issue 2 January 2013
Contents
....................................................................................................................................................................................................................................
3 Configuration basics
Configuration requirements
Configuration parameters
4 Configuration procedures
....................................................................................................................................................................................................................................
iv Alcatel-Lucent Proprietary Alcatel-Lucent 9353 WMS
Use pursuant to applicable agreements 9YZ-03450-3547-PGZZA UA08.1
Issue 2 January 2013
Contents
....................................................................................................................................................................................................................................
Configuring multi-mode MC-RRH parameters .......................................................................................................... 4-22
4-22
Index
....................................................................................................................................................................................................................................
Alcatel-Lucent 9353 WMS Alcatel-Lucent Proprietary v
9YZ-03450-3547-PGZZA UA08.1 Use pursuant to applicable agreements
Issue 2 January 2013
Contents
....................................................................................................................................................................................................................................
....................................................................................................................................................................................................................................
vi Alcatel-Lucent Proprietary Alcatel-Lucent 9353 WMS
Use pursuant to applicable agreements 9YZ-03450-3547-PGZZA UA08.1
Issue 2 January 2013
List of tables
....................................................................................................................................................................................................................................
Alcatel-Lucent 9353 WMS Alcatel-Lucent Proprietary vii
9YZ-03450-3547-PGZZA UA08.1 Use pursuant to applicable agreements
Issue 2 January 2013
List of tables
....................................................................................................................................................................................................................................
....................................................................................................................................................................................................................................
viii Alcatel-Lucent Proprietary Alcatel-Lucent 9353 WMS
Use pursuant to applicable agreements 9YZ-03450-3547-PGZZA UA08.1
Issue 2 January 2013
List of figures
....................................................................................................................................................................................................................................
Alcatel-Lucent 9353 WMS Alcatel-Lucent Proprietary ix
9YZ-03450-3547-PGZZA UA08.1 Use pursuant to applicable agreements
Issue 2 January 2013
List of figures
....................................................................................................................................................................................................................................
....................................................................................................................................................................................................................................
x Alcatel-Lucent Proprietary Alcatel-Lucent 9353 WMS
Use pursuant to applicable agreements 9YZ-03450-3547-PGZZA UA08.1
Issue 2 January 2013
About this document
About this document
Purpose
The purpose of this document is describe the procedures for configuring a BTS
equipment to use Alcatel-Lucent Multi-Carrier Remote Radio Head (MC-RRH) 900
MHz.
Intended audience
The audience for this document is configuration management personnel.
...................................................................................................................................................................................................................................
Alcatel-Lucent 9353 WMS Alcatel-Lucent Proprietary xi
9YZ-03450-3547-PGZZA UA08.1 Use pursuant to applicable agreements
Issue 2 January 2013
About this document
....................................................................................................................................................................................................................................
Supported systems
This document applies to Alcatel-Lucent W-CDMA UA08.1 system release.
This document applies to the following systems:
Alcatel-Lucent 9326 d2U
Alcatel-Lucent 9353 Wireless Management System
Alcatel-Lucent 9952 Wireless Provisioning System
Prerequisites
None.
Conventions used
Vocabulary conventions
Typographical conventions
The following typographical conventions are used in this document:
Appearance Description
italicized text File and directory names
Emphasized information
graphical user interface text Text that is displayed in a graphical user interface or in
a hardware label
variable A value that the user supplies
....................................................................................................................................................................................................................................
xii Alcatel-Lucent Proprietary Alcatel-Lucent 9353 WMS
Use pursuant to applicable agreements 9YZ-03450-3547-PGZZA UA08.1
Issue 2 January 2013
About this document
....................................................................................................................................................................................................................................
Appearance Description
key name The name of a key on the keyboard
command-syntax Command names that the user types
input text Text that the user types or selects as input to a system
output text Text that a system displays or prints
IP reference, reference number Related document that is referenced in the document
Related information
For information on subjects related to the content of this document, refer to the
documents listed in the following table:
....................................................................................................................................................................................................................................
Alcatel-Lucent 9353 WMS Alcatel-Lucent Proprietary xiii
9YZ-03450-3547-PGZZA UA08.1 Use pursuant to applicable agreements
Issue 2 January 2013
About this document
....................................................................................................................................................................................................................................
Document support
For support on using this or any other Alcatel-Lucent document, contact Alcatel-Lucent at
one of the following telephone numbers:
1-888-582-3688 (for the United States)
1-317-377-8618 (for all other countries)
Technical support
For technical support, contact your local Alcatel-Lucent customer support team. See the
Alcatel-Lucent Support web site (http://www.alcatel-lucent.com/support/) for contact
information.
How to order
To order Alcatel-Lucent documents, contact your local sales representative or use Online
Customer Support (OLCS) (http://support.alcatel-lucent.com).
How to comment
To comment on this document, go to the Online Comment Form (http://infodoc.alcatel-
lucent.com/comments/) or e-mail your comments to the Comments Hotline
(comments@alcatel-lucent.com).
....................................................................................................................................................................................................................................
xiv Alcatel-Lucent Proprietary Alcatel-Lucent 9353 WMS
Use pursuant to applicable agreements 9YZ-03450-3547-PGZZA UA08.1
Issue 2 January 2013
1 1oadmap to Configuration
R
Management
documentation
Overview
Purpose
This chapter provides the roadmap for Configuration Management documentation.
Contents
...................................................................................................................................................................................................................................
Alcatel-Lucent 9353 WMS Alcatel-Lucent Proprietary 1-1
9YZ-03450-3547-PGZZA UA08.1 Use pursuant to applicable agreements
Issue 2 January 2013
Roadmap to Configuration Management documentation Roadmap to Configuration Management documentation
....................................................................................................................................................................................................................................
....................................................................................................................................................................................................................................
1-2 Alcatel-Lucent Proprietary Alcatel-Lucent 9353 WMS
Use pursuant to applicable agreements 9YZ-03450-3547-PGZZA UA08.1
Issue 2 January 2013
2 MC-RRH overview
2
Overview
Purpose
This chapter provides generic information about Alcatel-Lucent Multi-Carrier Remote
Radio Head (MC-RRH) 900 MHz, its general architecture, its operating modes, and its
functions and benefits in the W-CDMA access network.
MC-RRH is radio module that facilitates NodeB to receive and transmit multiple carrier
signals, such as 2G or GSM and 3G or W-CDMA signals, on the same frequency band.
Thus, it helps the operators serve the GSM customers with W-CDMA users on the same
frequency band.
Contents
...................................................................................................................................................................................................................................
Alcatel-Lucent 9353 WMS Alcatel-Lucent Proprietary 2-1
9YZ-03450-3547-PGZZA UA08.1 Use pursuant to applicable agreements
Issue 2 January 2013
MC-RRH overview Overview
MC-RRH architecture
....................................................................................................................................................................................................................................
MC-RRH architecture
Overview
Purpose
This section describes the MC-RRH module and architecture.
Contents
....................................................................................................................................................................................................................................
2-2 Alcatel-Lucent Proprietary Alcatel-Lucent 9353 WMS
Use pursuant to applicable agreements 9YZ-03450-3547-PGZZA UA08.1
Issue 2 January 2013
MC-RRH overview MC-RRH and distributed BTS
MC-RRH architecture
....................................................................................................................................................................................................................................
....................................................................................................................................................................................................................................
Alcatel-Lucent 9353 WMS Alcatel-Lucent Proprietary 2-3
9YZ-03450-3547-PGZZA UA08.1 Use pursuant to applicable agreements
Issue 2 January 2013
MC-RRH overview MC-RRH and distributed BTS
MC-RRH architecture
....................................................................................................................................................................................................................................
For more details on MC-RRH equipment and hardware architecture, see Alcatel-Lucent
Remote Radio Head 2X40W - 900 MHz for GSM and W-CDMA - Technical Description,
NN-20500-281 and Alcatel-Lucent Remote Radio Head 2X40W - 900 MHz for GSM and
W-CDMA - Maintenance Guide, NN-20500-282.
Components of MC-RRH
MC-RRH is a single-sector radio module with the following components:
Two transmit paths of up to 40 W each
Two receive paths
Two PAs
Two CPRI interfaces and two GE interfaces
AISG connector
One external alarm connector for two open or close alarms
A LED unit
Hardware capable of supporting a single or multiple GSM and WCDMA carriers up
to 25 MHz of spectrum of bandwidth anywhere within the 35 MHz band.
MC-RRH characteristics
The MC-RRH has the following properties and benefits:
Supports an instantaneous bandwidth of 25 MHz in all RF paths
Configurable RF power on a per carrier basis
Supports up to four GSM and one W-CDMA carriers distributed over two PAs
Allows configuring a PA is dedicated to a particular technology (GSM or W-CDMA)
Supports multi-mode dual fiber
With the current system release, MC-RRH shall support multi-generation carriers (GSM
+ W-CDMA) operations.
....................................................................................................................................................................................................................................
2-4 Alcatel-Lucent Proprietary Alcatel-Lucent 9353 WMS
Use pursuant to applicable agreements 9YZ-03450-3547-PGZZA UA08.1
Issue 2 January 2013
MC-RRH overview MC-RRH and distributed BTS
MC-RRH architecture
....................................................................................................................................................................................................................................
As the SUMx 19-inch module supports only the MC-RRH, the TRE modules are
supported.
MC-RRH supports Antenna Line Device (ALD) interface port, antenna connections,
maintenance and diagnostic port, and electrical power input.
....................................................................................................................................................................................................................................
Alcatel-Lucent 9353 WMS Alcatel-Lucent Proprietary 2-5
9YZ-03450-3547-PGZZA UA08.1 Use pursuant to applicable agreements
Issue 2 January 2013
MC-RRH overview MC-RRH and distributed BTS
....................................................................................................................................................................................................................................
....................................................................................................................................................................................................................................
2-6 Alcatel-Lucent Proprietary Alcatel-Lucent 9353 WMS
Use pursuant to applicable agreements 9YZ-03450-3547-PGZZA UA08.1
Issue 2 January 2013
3 Configuration basics
3
Overview
Purpose
This chapter provides information about the configuration requirements, tasks, and
parameters required for configuring MC-RRH.
Contents
...................................................................................................................................................................................................................................
Alcatel-Lucent 9353 WMS Alcatel-Lucent Proprietary 3-1
9YZ-03450-3547-PGZZA UA08.1 Use pursuant to applicable agreements
Issue 2 January 2013
Configuration basics Overview
Configuration requirements
....................................................................................................................................................................................................................................
Configuration requirements
Overview
Purpose
This section provides information about the configuration requirements for using
MC-RRH.
Contents
....................................................................................................................................................................................................................................
3-2 Alcatel-Lucent Proprietary Alcatel-Lucent 9353 WMS
Use pursuant to applicable agreements 9YZ-03450-3547-PGZZA UA08.1
Issue 2 January 2013
Configuration basics Impacted network elements
Configuration requirements
....................................................................................................................................................................................................................................
....................................................................................................................................................................................................................................
Alcatel-Lucent 9353 WMS Alcatel-Lucent Proprietary 3-3
9YZ-03450-3547-PGZZA UA08.1 Use pursuant to applicable agreements
Issue 2 January 2013
Configuration basics Required access and restrictions
Configuration requirements
....................................................................................................................................................................................................................................
....................................................................................................................................................................................................................................
3-4 Alcatel-Lucent Proprietary Alcatel-Lucent 9353 WMS
Use pursuant to applicable agreements 9YZ-03450-3547-PGZZA UA08.1
Issue 2 January 2013
Configuration basics Overview
Configuration tasks and duration
....................................................................................................................................................................................................................................
Overview
Purpose
This section provides information about the configuration tasks and duration for using
MC-RRH.
Contents
....................................................................................................................................................................................................................................
Alcatel-Lucent 9353 WMS Alcatel-Lucent Proprietary 3-5
9YZ-03450-3547-PGZZA UA08.1 Use pursuant to applicable agreements
Issue 2 January 2013
Configuration basics Configuration tasks
Configuration tasks and duration
....................................................................................................................................................................................................................................
Configuration tasks
Prerequisites
The prerequisites for configuring MC-RRH are as follows:
MC-RRH must be installed and commissioned.
BTS must be installed and commissioned.
Global parameters must be set.
Latest applicable WPS must be installed.
Most up-to-date snapshot must be imported into WPS.
The templates for BTSEquipment configuration must be available in WPS.
WPS network view is configured.
See the table Table 3-1, Configuration task sequence (p. 3-6) for the sequence and
duration of tasks required for activation of MC-RRH.
....................................................................................................................................................................................................................................
3-6 Alcatel-Lucent Proprietary Alcatel-Lucent 9353 WMS
Use pursuant to applicable agreements 9YZ-03450-3547-PGZZA UA08.1
Issue 2 January 2013
Configuration basics Overview
Configuration parameters
....................................................................................................................................................................................................................................
Configuration parameters
Overview
Purpose
This section provides information about the configuration parameters for using MC-RRH.
Contents
....................................................................................................................................................................................................................................
Alcatel-Lucent 9353 WMS Alcatel-Lucent Proprietary 3-7
9YZ-03450-3547-PGZZA UA08.1 Use pursuant to applicable agreements
Issue 2 January 2013
Configuration basics Parameters for BTSEquipment and MC-RRH configuration
Configuration parameters
....................................................................................................................................................................................................................................
....................................................................................................................................................................................................................................
3-8 Alcatel-Lucent Proprietary Alcatel-Lucent 9353 WMS
Use pursuant to applicable agreements 9YZ-03450-3547-PGZZA UA08.1
Issue 2 January 2013
Configuration basics Parameters for BTSEquipment and MC-RRH configuration
Configuration parameters
....................................................................................................................................................................................................................................
RRH configuration parameters
Table RRH configuration parameters (p. 3-9)provides a list of parameters to be set at
the RRH object level.
....................................................................................................................................................................................................................................
Alcatel-Lucent 9353 WMS Alcatel-Lucent Proprietary 3-9
9YZ-03450-3547-PGZZA UA08.1 Use pursuant to applicable agreements
Issue 2 January 2013
Configuration basics Parameters for BTSEquipment and MC-RRH configuration
Configuration parameters
....................................................................................................................................................................................................................................
....................................................................................................................................................................................................................................
3-10 Alcatel-Lucent Proprietary Alcatel-Lucent 9353 WMS
Use pursuant to applicable agreements 9YZ-03450-3547-PGZZA UA08.1
Issue 2 January 2013
Configuration basics Parameters for BTSEquipment and MC-RRH configuration
Configuration parameters
....................................................................................................................................................................................................................................
....................................................................................................................................................................................................................................
Alcatel-Lucent 9353 WMS Alcatel-Lucent Proprietary 3-11
9YZ-03450-3547-PGZZA UA08.1 Use pursuant to applicable agreements
Issue 2 January 2013
Configuration basics Parameters for BTSEquipment and MC-RRH configuration
....................................................................................................................................................................................................................................
....................................................................................................................................................................................................................................
3-12 Alcatel-Lucent Proprietary Alcatel-Lucent 9353 WMS
Use pursuant to applicable agreements 9YZ-03450-3547-PGZZA UA08.1
Issue 2 January 2013
4 Configuration procedures
4
Overview
Purpose
This chapter provides information about the procedures for configuring the BTS
equipment with MC-RRH.
Note: These procedures are optional. Use these procedures only if the BTS equipment is
not available in the WPS network tree. If the BTS equipment is available, skip to
Configuring multi-mode MC-RRH parameters (p. 4-22).
Contents
...................................................................................................................................................................................................................................
Alcatel-Lucent 9353 WMS Alcatel-Lucent Proprietary 4-1
9YZ-03450-3547-PGZZA UA08.1 Use pursuant to applicable agreements
Issue 2 January 2013
Configuration procedures Overview
Initial configuration procedures
....................................................................................................................................................................................................................................
Overview
Purpose
This section provides information about the initial configuration procedures for using
MC-RRH.
Contents
....................................................................................................................................................................................................................................
4-2 Alcatel-Lucent Proprietary Alcatel-Lucent 9353 WMS
Use pursuant to applicable agreements 9YZ-03450-3547-PGZZA UA08.1
Issue 2 January 2013
Configuration procedures Setting global parameters
Initial configuration procedures
....................................................................................................................................................................................................................................
....................................................................................................................................................................................................................................
Alcatel-Lucent 9353 WMS Alcatel-Lucent Proprietary 4-3
9YZ-03450-3547-PGZZA UA08.1 Use pursuant to applicable agreements
Issue 2 January 2013
Configuration procedures Overview
Configuring BTS equipment with MC-RRH
....................................................................................................................................................................................................................................
Overview
Purpose
The purpose of this section is to provide step-by-step procedures to configure a BTS
equipment to use MC-RRH with the WPS.
Note: This section also describes the procedure to create a BTSEquipment in WPS. If the
BTS equipment to configure is already available in the WPS network tree, follow the
procedures described in Configuring multi-mode MC-RRH parameters (p. 4-22).
Contents
....................................................................................................................................................................................................................................
4-4 Alcatel-Lucent Proprietary Alcatel-Lucent 9353 WMS
Use pursuant to applicable agreements 9YZ-03450-3547-PGZZA UA08.1
Issue 2 January 2013
Configuration procedures Creating a BTSEquipment for multi mode MC-RRH
Configuring BTS equipment with MC-RRH
....................................................................................................................................................................................................................................
Related information
For more information about the parameters set for this procedure, use the embedded Help
function (F1 key) or see Alcatel-Lucent 9353 Wireless Management System - Parameters
Reference Guide, NN-20500-027.
Procedure
Perform these steps for configuring the BTSEquipment for MC-RRH configuration.
...................................................................................................................................................................................................
3 From the Object Editor: Overview panel, click the NodeB wizard link.
....................................................................................................................................................................................................................................
Alcatel-Lucent 9353 WMS Alcatel-Lucent Proprietary 4-5
9YZ-03450-3547-PGZZA UA08.1 Use pursuant to applicable agreements
Issue 2 January 2013
Configuration procedures Creating a BTSEquipment for multi mode MC-RRH
Configuring BTS equipment with MC-RRH
....................................................................................................................................................................................................................................
Result: The NodeB wizard window appears.
...................................................................................................................................................................................................
4 From the NodeB wizard task tree, select the BTS Equipment Configuration task.
...................................................................................................................................................................................................
...................................................................................................................................................................................................
....................................................................................................................................................................................................................................
4-6 Alcatel-Lucent Proprietary Alcatel-Lucent 9353 WMS
Use pursuant to applicable agreements 9YZ-03450-3547-PGZZA UA08.1
Issue 2 January 2013
Configuration procedures Creating a BTSEquipment for multi mode MC-RRH
Configuring BTS equipment with MC-RRH
....................................................................................................................................................................................................................................
...................................................................................................................................................................................................
10 Select an appropriate RRH Configuration from the drop-down list and click OK.
Note: For STSR1, select RRH1 from the drop-down list.
A BTSEquipment has been created successfully.
E...................................................................................................................................................................................................
N D O F S T E P S
....................................................................................................................................................................................................................................
Alcatel-Lucent 9353 WMS Alcatel-Lucent Proprietary 4-7
9YZ-03450-3547-PGZZA UA08.1 Use pursuant to applicable agreements
Issue 2 January 2013
Configuration procedures Configuring a BTSEquipment for multi-mode MC-RRH
Configuring BTS equipment with MC-RRH
....................................................................................................................................................................................................................................
Related information
For more information about the parameters set for this procedure, use the embedded Help
function (F1 key) or see Alcatel-Lucent 9353 Wireless Management System - Parameters
Reference Guide, NN-20500-027.
Procedure
Perform the following steps to configure MC-RRH usage in multi mode:
...................................................................................................................................................................................................
3 From the Object Editor: Overview panel, click the NodeB wizard link.
Result: The NodeB wizard window appears.
...................................................................................................................................................................................................
4 From the NodeB wizard task tree, select the BTS Equipment Configuration task.
...................................................................................................................................................................................................
6 Make the necessary configuration changes in the Operation: Configure BTS Equipment
window and click OK.
....................................................................................................................................................................................................................................
4-8 Alcatel-Lucent Proprietary Alcatel-Lucent 9353 WMS
Use pursuant to applicable agreements 9YZ-03450-3547-PGZZA UA08.1
Issue 2 January 2013
Configuration procedures Configuring a BTSEquipment for multi-mode MC-RRH
Configuring BTS equipment with MC-RRH
....................................................................................................................................................................................................................................
The figure Figure 4-2, Configuring BTSEquipment - one frequency (p. 4-9) shows an
example for configuring BTSEquipment for one frequency.
....................................................................................................................................................................................................................................
Alcatel-Lucent 9353 WMS Alcatel-Lucent Proprietary 4-9
9YZ-03450-3547-PGZZA UA08.1 Use pursuant to applicable agreements
Issue 2 January 2013
Configuration procedures Configuring a BTSEquipment for multi-mode MC-RRH
Configuring BTS equipment with MC-RRH
....................................................................................................................................................................................................................................
The figure Figure 4-3, Configuring BTSEquipment - two frequencies (p. 4-10) shows an
example for configuring BTSEquipment for two frequencies.
....................................................................................................................................................................................................................................
4-10 Alcatel-Lucent Proprietary Alcatel-Lucent 9353 WMS
Use pursuant to applicable agreements 9YZ-03450-3547-PGZZA UA08.1
Issue 2 January 2013
Configuration procedures Configuring BTS Cells
Configuring BTS equipment with MC-RRH
....................................................................................................................................................................................................................................
Related information
For more information about the parameters set for this procedure, use the embedded Help
function (F1 key) or see Alcatel-Lucent 9353 Wireless Management System - Parameters
Reference Guide, NN-20500-027.
Procedure
Perform these steps for configuring the BTS Cells for MC-RRH:
...................................................................................................................................................................................................
3 From the Object Editor: Overview panel, click the NodeB wizard link.
Result: The NodeB wizard window appears.
...................................................................................................................................................................................................
4 From the NodeB wizard task tree, select the BTS Equipment Configuration task.
...................................................................................................................................................................................................
....................................................................................................................................................................................................................................
Alcatel-Lucent 9353 WMS Alcatel-Lucent Proprietary 4-11
9YZ-03450-3547-PGZZA UA08.1 Use pursuant to applicable agreements
Issue 2 January 2013
Configuration procedures Configuring BTS Cells
Configuring BTS equipment with MC-RRH
....................................................................................................................................................................................................................................
Result: The Operation: Configure BTS Cells window is displayed, as shown in the
Figure 4-4, Operation: Configure BTS cells (p. 4-12).
...................................................................................................................................................................................................
6 Make the necessary configuration changes in the Operation: Configure BTS Cells
window and click OK.
The BTS Cells have been configured successfully.
E...................................................................................................................................................................................................
N D O F S T E P S
....................................................................................................................................................................................................................................
4-12 Alcatel-Lucent Proprietary Alcatel-Lucent 9353 WMS
Use pursuant to applicable agreements 9YZ-03450-3547-PGZZA UA08.1
Issue 2 January 2013
Configuration procedures Configuring NodeB
Configuring BTS equipment with MC-RRH
....................................................................................................................................................................................................................................
Configuring NodeB
Purpose
This procedure describes how to configure NodeB for multi mode MC-RRH.
Related information
For more information about the parameters set for this procedure, use the embedded Help
function (F1 key) or see Alcatel-Lucent 9353 Wireless Management System - Parameters
Reference Guide, NN-20500-027.
Procedure
Perform these steps for configuring the NodeB for an MC-RRH:
...................................................................................................................................................................................................
3 From the Object Editor: Overview panel, click the NodeB wizard link.
Result: The NodeB wizard window appears.
...................................................................................................................................................................................................
4 From the NodeB wizard task tree, select the NodeB Configuration task.
...................................................................................................................................................................................................
....................................................................................................................................................................................................................................
Alcatel-Lucent 9353 WMS Alcatel-Lucent Proprietary 4-13
9YZ-03450-3547-PGZZA UA08.1 Use pursuant to applicable agreements
Issue 2 January 2013
Configuration procedures Configuring NodeB
Configuring BTS equipment with MC-RRH
....................................................................................................................................................................................................................................
Result: The Operation: Configure NodeB window is displayed, as shown in the
figure Figure 4-5, Operation: Configure NodeB (p. 4-14).
...................................................................................................................................................................................................
6 Make the necessary configuration changes in the Operation: Configure NodeB window
and click OK.
...................................................................................................................................................................................................
7 From the NodeB Configuration task tree, click Define FddCell Radio Configuration.
Result: The Operation: Define FddCell Radio Configuration window appears.
...................................................................................................................................................................................................
8 Enter the appropriate values for the required attributes and click OK.
....................................................................................................................................................................................................................................
4-14 Alcatel-Lucent Proprietary Alcatel-Lucent 9353 WMS
Use pursuant to applicable agreements 9YZ-03450-3547-PGZZA UA08.1
Issue 2 January 2013
Configuration procedures Configuring NodeB
Configuring BTS equipment with MC-RRH
....................................................................................................................................................................................................................................
Result: The Define FddCell Localization Configuration operation is available.
...................................................................................................................................................................................................
9 From the NodeB Configuration task tree, click Define FddCell Localization
Configuration.
Result: The Operation: Define FddCell Localization Configuration window
appears.
...................................................................................................................................................................................................
10 Enter the appropriate values for the required attributes, and then click OK.
...................................................................................................................................................................................................
11 From the NodeB Configuration task tree, click Define FddCell GaiCoord configuration.
Result: The Operation: Define FddCell GaiCoord configuration window appears.
...................................................................................................................................................................................................
12 Enter an appropriate value for the Number of geographical points parameter and click
the Number of geographical points field to display the List of GaiCoord.
...................................................................................................................................................................................................
13 Enter the appropriate values for the required attributes, and then click OK.
...................................................................................................................................................................................................
14 From the NodeB wizard task tree, select the Channels Configuration sub-task.
...................................................................................................................................................................................................
16 Enter the appropriate values for the required attributes, and then click OK.
Result: The NodeB Configuration task turns green.
...................................................................................................................................................................................................
....................................................................................................................................................................................................................................
Alcatel-Lucent 9353 WMS Alcatel-Lucent Proprietary 4-15
9YZ-03450-3547-PGZZA UA08.1 Use pursuant to applicable agreements
Issue 2 January 2013
Configuration procedures Configuring BTS site
Configuring BTS equipment with MC-RRH
....................................................................................................................................................................................................................................
Related information
For more information about the parameters set for this procedure, use the embedded Help
function (F1 key) or see Alcatel-Lucent 9353 Wireless Management System - Parameters
Reference Guide, NN-20500-027.
Procedure
Perform these steps for configuring the BTS site in STSR1 configuration.
...................................................................................................................................................................................................
3 From the Object Editor: Overview panel, click the NodeB wizard link.
Result: The NodeB wizard window appears.
...................................................................................................................................................................................................
4 From the NodeB wizard task tree, select the Site Configuration task.
...................................................................................................................................................................................................
....................................................................................................................................................................................................................................
4-16 Alcatel-Lucent Proprietary Alcatel-Lucent 9353 WMS
Use pursuant to applicable agreements 9YZ-03450-3547-PGZZA UA08.1
Issue 2 January 2013
Configuration procedures Configuring BTS site
Configuring BTS equipment with MC-RRH
....................................................................................................................................................................................................................................
Result: The Operation: Configure site window is displayed, as shown in the
following diagram.
...................................................................................................................................................................................................
....................................................................................................................................................................................................................................
Alcatel-Lucent 9353 WMS Alcatel-Lucent Proprietary 4-17
9YZ-03450-3547-PGZZA UA08.1 Use pursuant to applicable agreements
Issue 2 January 2013
Configuration procedures Configuring MC-RRH site
Configuring BTS equipment with MC-RRH
....................................................................................................................................................................................................................................
Related information
For more information about the parameters set for this procedure, use the embedded Help
function (F1 key) or see Alcatel-Lucent 9353 Wireless Management System - Parameters
Reference Guide, NN-20500-027.
Procedure
Perform the following steps for configuring the MC-RRH site.
...................................................................................................................................................................................................
3 From the Object Editor: Overview panel, click the NodeB wizard link.
Result: The NodeB wizard window appears.
...................................................................................................................................................................................................
4 From the NodeB wizard task tree, select the Site Configuration task.
...................................................................................................................................................................................................
....................................................................................................................................................................................................................................
4-18 Alcatel-Lucent Proprietary Alcatel-Lucent 9353 WMS
Use pursuant to applicable agreements 9YZ-03450-3547-PGZZA UA08.1
Issue 2 January 2013
Configuration procedures Configuring MC-RRH site
Configuring BTS equipment with MC-RRH
....................................................................................................................................................................................................................................
Result: The Operation: Configure site window is displayed, as shown in the
following diagram.
...................................................................................................................................................................................................
....................................................................................................................................................................................................................................
Alcatel-Lucent 9353 WMS Alcatel-Lucent Proprietary 4-19
9YZ-03450-3547-PGZZA UA08.1 Use pursuant to applicable agreements
Issue 2 January 2013
Configuration procedures Defining antenna system
Configuring BTS equipment with MC-RRH
....................................................................................................................................................................................................................................
Related information
For more information about the parameters set for this procedure, use the embedded Help
function (F1 key) or see Alcatel-Lucent 9353 Wireless Management System - Parameters
Reference Guide, NN-20500-027.
Procedure
Perform these steps for defining antenna system for MC-RRH.
...................................................................................................................................................................................................
3 From the Object Editor: Overview panel, click the NodeB wizard link.
Result: The NodeB wizard window appears.
...................................................................................................................................................................................................
4 From the NodeB wizard task tree, select the Site Configuration task.
...................................................................................................................................................................................................
....................................................................................................................................................................................................................................
4-20 Alcatel-Lucent Proprietary Alcatel-Lucent 9353 WMS
Use pursuant to applicable agreements 9YZ-03450-3547-PGZZA UA08.1
Issue 2 January 2013
Configuration procedures Defining antenna system
Configuring BTS equipment with MC-RRH
....................................................................................................................................................................................................................................
Result: The Operation: Antenna System Definition window is displayed, as shown
in Figure 4-6, Operation: Antenna system definition (p. 4-21).
...................................................................................................................................................................................................
6 Make the necessary configuration changes in the Operation: Configure NodeB window
and click OK.
The antenna system has been defined successfully.
E...................................................................................................................................................................................................
N D O F S T E P S
....................................................................................................................................................................................................................................
Alcatel-Lucent 9353 WMS Alcatel-Lucent Proprietary 4-21
9YZ-03450-3547-PGZZA UA08.1 Use pursuant to applicable agreements
Issue 2 January 2013
Configuration procedures Configuring multi-mode MC-RRH parameters
Configuring BTS equipment with MC-RRH
....................................................................................................................................................................................................................................
4 Ensure that the appropriate values are set for this parameter.
Note: The recommended value for this parameter depends on commercial agreement
and installed PA resources.
...................................................................................................................................................................................................
6 Ensure that the appropriate values are set for this parameter.
....................................................................................................................................................................................................................................
4-22 Alcatel-Lucent Proprietary Alcatel-Lucent 9353 WMS
Use pursuant to applicable agreements 9YZ-03450-3547-PGZZA UA08.1
Issue 2 January 2013
Configuration procedures Configuring multi-mode MC-RRH parameters
Configuring BTS equipment with MC-RRH
....................................................................................................................................................................................................................................
Note: The value 0 means that all RRH modules are WCDMA mono-carrier, whereas
value 1 means that all RRH modules are WCDMA bi-carriers (not allowed for
MC-RRH in V7.1.3).
...................................................................................................................................................................................................
7 In the Object Editor: Edition panel, check for the following parameter:
rrhTrduThirdCarrierCapacityLicensing
E...................................................................................................................................................................................................
N D O F S T E P S
3 From the Object Editor: Edition panel, select the rrhNumberFrequency parameter.
Note: This attribute cannot be used if carrier capacity licensing is not unlimited. Value
0 means no software locking of Number Frequency for an RRH; 1 means that RRH
can manage one frequency only; and 2 means that RRH can manage two frequencies.
The default value is 1 in the current release.
...................................................................................................................................................................................................
4 In the Object Editor: Edition panel, check for the following parameters:
rrhGroupId - is an optional parameter.
rrhMode - has to be set to 0 (sectorMode) as repeaterMode is not supported.
AntennaConnectionId
E...................................................................................................................................................................................................
N D O F S T E P S
3 From the Object Editor: Edition panel, select the maxRrhPowerAmplification parameter.
Ensure that appropriate values have been set for this parameter.
Note: This attribute can have allowed values, fullMode, max10W, max20W, max30W,
and max40W. The value fullMode is equivalent with the value max40W. The value
max60W cannot be used in the current release.
Note: Only one PaResource object per RemoteRadioHead object is instantiated in the
multi mode currently.
E...................................................................................................................................................................................................
N D O F S T E P S
....................................................................................................................................................................................................................................
4-24 Alcatel-Lucent Proprietary Alcatel-Lucent 9353 WMS
Use pursuant to applicable agreements 9YZ-03450-3547-PGZZA UA08.1
Issue 2 January 2013
Configuration procedures Exporting workorders
Configuring BTS equipment with MC-RRH
....................................................................................................................................................................................................................................
Exporting workorders
Purpose
Use this procedure to generate the XML file with configuration settings for activating
MC-RRH.
Related information
This procedure facilitates speeding up the whole process, by exporting only the relevant
applicable modifications on the Main Server.
Procedure
...................................................................................................................................................................................................
2 Select an option to save the workspace. If required, enter a new workspace name, and
click Run.
...................................................................................................................................................................................................
5 Right-click on the selected workorder and select Export workorder from the contextual
menu.
To export the workorder to a local directory, select the on local file system option.
To export the workorder to a live server repository, select on live server repository
option.
....................................................................................................................................................................................................................................
Alcatel-Lucent 9353 WMS Alcatel-Lucent Proprietary 4-25
9YZ-03450-3547-PGZZA UA08.1 Use pursuant to applicable agreements
Issue 2 January 2013
Configuration procedures Exporting workorders
Configuring BTS equipment with MC-RRH
....................................................................................................................................................................................................................................
...................................................................................................................................................................................................
....................................................................................................................................................................................................................................
4-26 Alcatel-Lucent Proprietary Alcatel-Lucent 9353 WMS
Use pursuant to applicable agreements 9YZ-03450-3547-PGZZA UA08.1
Issue 2 January 2013
5 5erforming checks and
P
workorder activation
Overview
Purpose
This chapter provides information about procedures used to perform post-activation
checks and to activate a workorder in WMS.
Contents
...................................................................................................................................................................................................................................
Alcatel-Lucent 9353 WMS Alcatel-Lucent Proprietary 5-1
9YZ-03450-3547-PGZZA UA08.1 Use pursuant to applicable agreements
Issue 2 January 2013
Performing checks and workorder activation Overview
Verifying the configuration and workorder activation in
WMS
....................................................................................................................................................................................................................................
Overview
Purpose
This section provides information about the procedures for verifying the configuration of
multi-mode MC-RRH and activating the workorder in WMS.
Contents
....................................................................................................................................................................................................................................
5-2 Alcatel-Lucent Proprietary Alcatel-Lucent 9353 WMS
Use pursuant to applicable agreements 9YZ-03450-3547-PGZZA UA08.1
Issue 2 January 2013
Performing checks and workorder activation Performing pre-activation checks
Verifying the configuration and workorder activation in
WMS
....................................................................................................................................................................................................................................
Actions
Perform the following actions:
Check that no impacting alarms exist.
For more information, see the following documents:
Alcatel-Lucent 9353 Wireless Management System - User Guide, NN-20500-032
Alcatel-Lucent W-CDMA System - Document Collection Overview, NN-20500-050
Perform an audit of the impacted RNCs. For more information, see Alcatel-Lucent
9353 Wireless Management System - User Guide, NN-20500-032.
Check if calls can be established on the RNC and cells impacted by the feature
activation.
The network and the OMC are running without any problem.
....................................................................................................................................................................................................................................
Alcatel-Lucent 9353 WMS Alcatel-Lucent Proprietary 5-3
9YZ-03450-3547-PGZZA UA08.1 Use pursuant to applicable agreements
Issue 2 January 2013
Performing checks and workorder activation Activating a workorder in WMS
Verifying the configuration and workorder activation in
WMS
....................................................................................................................................................................................................................................
Input parameters
The workorder (CM XML) file generated by WPS ACCESS is transferred to a destination
directory on the main server as described in Alcatel-Lucent 9353 Wireless Management
System - User Guide, NN-20500-032.
Procedure
...................................................................................................................................................................................................
1 From the WMS client menu bar, select Configuration -> Sessions Manager.
Result: The Sessions Manager window appears.
...................................................................................................................................................................................................
3 In the Create Session window - Creation parameters pane, enter a <Session Name>.
...................................................................................................................................................................................................
....................................................................................................................................................................................................................................
5-4 Alcatel-Lucent Proprietary Alcatel-Lucent 9353 WMS
Use pursuant to applicable agreements 9YZ-03450-3547-PGZZA UA08.1
Issue 2 January 2013
Performing checks and workorder activation Activating a workorder in WMS
Verifying the configuration and workorder activation in
WMS
....................................................................................................................................................................................................................................
Result: The workorder is added in the right pane.
...................................................................................................................................................................................................
8 After session creation completion without errors, in the Actions for <session name> tab,
click Activation.
...................................................................................................................................................................................................
10 When all tasks are completed, in the Sessions Manager window, click on Summary for
<session name> to check that the impacted BTS is in Activated state.
...................................................................................................................................................................................................
11 In the Session list, right-click <session name> and select Terminate from the contextual
menu to delete the session.
Result: The new configuration is activated on the BTS.
E...................................................................................................................................................................................................
N D O F S T E P S
....................................................................................................................................................................................................................................
Alcatel-Lucent 9353 WMS Alcatel-Lucent Proprietary 5-5
9YZ-03450-3547-PGZZA UA08.1 Use pursuant to applicable agreements
Issue 2 January 2013
Performing checks and workorder activation Performing post-activation checks
Verifying the configuration and workorder activation in
WMS
....................................................................................................................................................................................................................................
Steps
Perform the following operations:
Check that no impacting alarms exist.
For more information, see the following documents:
Alcatel-Lucent 9353 Wireless Management System - User Guide, NN-20500-032
Alcatel-Lucent 9300 W-CDMA System - Document Collection Overview and
Update Summary, NN-20500-050
Perform calls on the RNCs and the cells for which the feature is activated.
....................................................................................................................................................................................................................................
5-6 Alcatel-Lucent Proprietary Alcatel-Lucent 9353 WMS
Use pursuant to applicable agreements 9YZ-03450-3547-PGZZA UA08.1
Issue 2 January 2013
Performing checks and workorder activation Activating reverse workorder
Verifying the configuration and workorder activation in
WMS
....................................................................................................................................................................................................................................
Steps
Perform the following steps to reverse a workorder activation:
...................................................................................................................................................................................................
1 From the WMS menu bar, select Configuration -> Sessions Manager.
Result: The Sessions Manager window appears.
...................................................................................................................................................................................................
2 From the Sessions Manager window, select any of the following options:
In the Session Tasks panel, click Create new session.
InAvailable Sessions panel, right-click Sessions list and select New.
Result: The Create Session window appears.
...................................................................................................................................................................................................
....................................................................................................................................................................................................................................
Alcatel-Lucent 9353 WMS Alcatel-Lucent Proprietary 5-7
9YZ-03450-3547-PGZZA UA08.1 Use pursuant to applicable agreements
Issue 2 January 2013
Performing checks and workorder activation Activating reverse workorder
Verifying the configuration and workorder activation in
WMS
....................................................................................................................................................................................................................................
Result: The Excluded Nodes panel on the Create Session window appears.
...................................................................................................................................................................................................
8 After the session is created without any errors, click Validation in the Actions for
<reverse session name> panel.
...................................................................................................................................................................................................
9 Click Launch.
...................................................................................................................................................................................................
13 Perform the following actions to check the validation report for each node in the summary
section:
Click Summary for <reverse session name>.
Ensure that the impacted nodes are in the Excluded state.
Ensure that the NodesBs are removed.
...................................................................................................................................................................................................
14 After the validation is completed without any errors, if the I-Nodes are not listed in the
summary, go to Step 15. Otherwise, perform the following actions:
In the Actions for <reverse session name> panel, click Activation.
Select all the impacted nodes, and then click Launch.
Click Summary for <reverse session name> and ensure that all the impacted nodes
are in the Activated state.
....................................................................................................................................................................................................................................
5-8 Alcatel-Lucent Proprietary Alcatel-Lucent 9353 WMS
Use pursuant to applicable agreements 9YZ-03450-3547-PGZZA UA08.1
Issue 2 January 2013
Performing checks and workorder activation Activating reverse workorder
Verifying the configuration and workorder activation in
WMS
....................................................................................................................................................................................................................................
...................................................................................................................................................................................................
15 After the changed NEs are validated without errors, click Activation in the Actions for
<reverse session name> panel, and perform the following actions:
Select all the impacted RNCs and click Launch.
When all tasks are completed, click Summary for <reverse session name> to ensure
that the impacted RNCs are in the Activated state.
...................................................................................................................................................................................................
16 From the Sessions Manager window, right-click on the Session List, and select
Terminate.
E...................................................................................................................................................................................................
N D O F S T E P S
Troubleshooting
Table 5-1, Reverse workorder activation (p. 5-9) describes the troubleshooting actions
to perform, in case of failed operations.
....................................................................................................................................................................................................................................
Alcatel-Lucent 9353 WMS Alcatel-Lucent Proprietary 5-9
9YZ-03450-3547-PGZZA UA08.1 Use pursuant to applicable agreements
Issue 2 January 2013
Performing checks and workorder activation Activating reverse workorder
Verifying the configuration and workorder activation in
WMS
....................................................................................................................................................................................................................................
Table 5-1 Reverse workorder activation (continued)
....................................................................................................................................................................................................................................
5-10 Alcatel-Lucent Proprietary Alcatel-Lucent 9353 WMS
Use pursuant to applicable agreements 9YZ-03450-3547-PGZZA UA08.1
Issue 2 January 2013
Index
....................................................................................................................................................................................................................................
impacted NEs and system, 3-3 workorders
important features, 2-4 exporting online, 4-25
introduction, 2-1, 3-1
login, 3-4
MC-RRH and distributed BTS, 2-3
overview, 2-3
post activation checks, 5-1
restrictions, 3-4
supported equipments, 2-4
................................................................................................
P procedures
................................................................................................
W WMS
....................................................................................................................................................................................................................................
IN-2 Alcatel-Lucent Proprietary Alcatel-Lucent 9353 WMS
Use pursuant to applicable agreements 9YZ-03450-3547-PGZZA UA08.1
Issue 2 January 2013