Beruflich Dokumente
Kultur Dokumente
Title page
Alcatel-Lucent 9311
Macro V2 Node B Outdoor | UA08.1
Corrective Maintenance
NN-20500-011
Issue 09.07 | January 2013
Alcatel-Lucent Proprietary
Use pursuant to applicable agreements
Use pursuant to applicable agreements
Legal notice
Legal notice
Alcatel, Lucent, Alcatel-Lucent and the Alcatel-Lucent logo are trademarks of Alcatel-Lucent. All other trademarks are the property of their respective
owners.
The information presented is subject to change without notice. Alcatel-Lucent assumes no responsibility for inaccuracies contained herein.
Copyright 2013 Alcatel-Lucent. All rights reserved.
Contains proprietary/trade secret information which is the property of Alcatel-Lucent and must not be made available to, or copied or used by anyone outside
Alcatel-Lucent without its written authorization.
Not to be used or disclosed except in accordance with applicable agreements.
Alcatel-Lucent Proprietary
Use pursuant to applicable agreements
Contents
2 Safety statements
....................................................................................................................................................................................................................................
Corrective maintenance activity .......................................................................................................................................... 3-2
3-2
Replacing the GPS interface and Alarm Module (GPSAM) .................................................................................. 8-23
8-23
Replacing the optional xCCM radio interface Board (xCOB) ............................................................................... 8-50
8-50
....................................................................................................................................................................................................................................
iv Alcatel-Lucent Proprietary Alcatel-Lucent 9311 Macro V2 OD
Use pursuant to applicable agreements NN-20500-011 UA08.1
Issue 09.07 January 2013
Contents
....................................................................................................................................................................................................................................
Replacing the RF block equipment
Replacing the Multi-Carrier Power Amplifier module (MCPA) or Single-Carrier Power Amplifier
module (SCPA) ............................................................................................................................................................... 8-64
8-64
Replacing the Manufacturing Commissioning and Alarm (MCA) module .................................................... 8-126
8-126
Replacing the Power Amplifier InterCOnnection (PA ICO) module ................................................................ 8-145
8-145
....................................................................................................................................................................................................................................
Alcatel-Lucent 9311 Macro V2 OD Alcatel-Lucent Proprietary v
NN-20500-011 UA08.1 Use pursuant to applicable agreements
Issue 09.07 January 2013
Contents
....................................................................................................................................................................................................................................
Replacing the Radio Frequency InterCOnnection (RF ICO) module ............................................................... 8-149
8-149
Index
....................................................................................................................................................................................................................................
vi Alcatel-Lucent Proprietary Alcatel-Lucent 9311 Macro V2 OD
Use pursuant to applicable agreements NN-20500-011 UA08.1
Issue 09.07 January 2013
List of tables
....................................................................................................................................................................................................................................
Alcatel-Lucent 9311 Macro V2 OD Alcatel-Lucent Proprietary vii
NN-20500-011 UA08.1 Use pursuant to applicable agreements
Issue 09.07 January 2013
List of tables
....................................................................................................................................................................................................................................
....................................................................................................................................................................................................................................
viii Alcatel-Lucent Proprietary Alcatel-Lucent 9311 Macro V2 OD
Use pursuant to applicable agreements NN-20500-011 UA08.1
Issue 09.07 January 2013
List of figures
5-1 9311 Macro V2 OD general view with PA, DDM ....................................................................................... 5-3
....................................................................................................................................................................................................................................
Alcatel-Lucent 9311 Macro V2 OD Alcatel-Lucent Proprietary ix
NN-20500-011 UA08.1 Use pursuant to applicable agreements
Issue 09.07 January 2013
List of figures
....................................................................................................................................................................................................................................
8-17 GPxOIM front panel (with C2OIM inserted) ............................................................................................... 8-36
....................................................................................................................................................................................................................................
8-44 ECU ASSY S180 .................................................................................................................................................. 8-100
8-62 Disconnection of the User ICO supply cable from the DDU ............................................................... 8-166
....................................................................................................................................................................................................................................
Alcatel-Lucent 9311 Macro V2 OD Alcatel-Lucent Proprietary xi
NN-20500-011 UA08.1 Use pursuant to applicable agreements
Issue 09.07 January 2013
List of figures
....................................................................................................................................................................................................................................
....................................................................................................................................................................................................................................
xii Alcatel-Lucent Proprietary Alcatel-Lucent 9311 Macro V2 OD
Use pursuant to applicable agreements NN-20500-011 UA08.1
Issue 09.07 January 2013
About this document
About this document
Purpose
The purpose of this document is to describe the corrective maintenance procedures
applicable to the Alcatel-Lucent 9311 Macro V2 Node B Outdoor. Its short name is 9311
Macro V2 OD.
...................................................................................................................................................................................................................................
Alcatel-Lucent 9311 Macro V2 OD Alcatel-Lucent Proprietary xiii
NN-20500-011 UA08.1 Use pursuant to applicable agreements
Issue 09.07 January 2013
About this document
....................................................................................................................................................................................................................................
Intended audience
The audience for this document is Operations and maintenance personnel, and for those
who want to know the principles of 9311 Macro OD corrective maintenance.
Supported systems
This document applies to Alcatel-Lucent W-CDMA UA08.1 system release.
Safety information
For your safety, this document contains safety statements. Safety statements are given at
points where risks of damage to personnel, equipment, and operation may exist. Failure to
follow the directions in a safety statement may result in serious consequences.
Prerequisites
It is recommended that readers become familiar with the following publications:
Alcatel-Lucent 9311 Macro V2 Node B Outdoor documentation:
Technical Description, NN-20500-004
Preventive Maintenance, NN-20500-010
Conventions used
Vocabulary conventions
For a list of the terms used in this document, see Alcatel-Lucent W-CDMA System -
Terminology, NN-20500-002
This document uses some terms generically.
....................................................................................................................................................................................................................................
xiv Alcatel-Lucent Proprietary Alcatel-Lucent 9311 Macro V2 OD
Use pursuant to applicable agreements NN-20500-011 UA08.1
Issue 09.07 January 2013
About this document
....................................................................................................................................................................................................................................
Table 1 Generic terms (continued)
Typographical conventions
The following typographical conventions are used in this document:
Appearance Description
IP reference, reference number Related document that is referenced in the document
Bold text or Italicized text Emphasized information
graphical user interface text Text that is displayed in a graphical user interface or
in a hardware label
Related information
For information on subjects related to the content of this document, refer to the
documents listed in the following table:
....................................................................................................................................................................................................................................
Alcatel-Lucent 9311 Macro V2 OD Alcatel-Lucent Proprietary xv
NN-20500-011 UA08.1 Use pursuant to applicable agreements
Issue 09.07 January 2013
About this document
....................................................................................................................................................................................................................................
Document support
For support in using this or any other Alcatel-Lucent document, contact Alcatel-Lucent at
one of the following telephone numbers:
1-888-582-3688 (for the United States)
1-630-224-2485 (for all other countries)
Technical support
For technical support, contact your local Alcatel-Lucent customer support team. See the
Alcatel-Lucent Support web site (http://www.alcatel-lucent.com/support/) for contact
information.
How to order
To order Alcatel-Lucent documents, contact your local sales representative or use Online
Customer Support (OLCS) (http://support.alcatel-lucent.com)
How to comment
To comment on this document, go to the Online Comment Form (http://infodoc.alcatel-
lucent.com/comments/) or e-mail your comments to the Comments Hotline
(comments@alcatel-lucent.com).
....................................................................................................................................................................................................................................
xvi Alcatel-Lucent Proprietary Alcatel-Lucent 9311 Macro V2 OD
Use pursuant to applicable agreements NN-20500-011 UA08.1
Issue 09.07 January 2013
1 1oadmap to Conventional
R
Base Station
documentation
Overview
Purpose
This chapter provides the roadmap for Conventional Base Station documentation.
Contents
...................................................................................................................................................................................................................................
Alcatel-Lucent 9311 Macro V2 OD Alcatel-Lucent Proprietary 1-1
NN-20500-011 UA08.1 Use pursuant to applicable agreements
Issue 09.07 January 2013
Roadmap to Conventional Base Station documentation Roadmap to Conventional Base Station documentation
....................................................................................................................................................................................................................................
....................................................................................................................................................................................................................................
1-2 Alcatel-Lucent Proprietary Alcatel-Lucent 9311 Macro V2 OD
Use pursuant to applicable agreements NN-20500-011 UA08.1
Issue 09.07 January 2013
Roadmap to Conventional Base Station documentation Roadmap to Conventional Base Station documentation
....................................................................................................................................................................................................................................
....................................................................................................................................................................................................................................
Alcatel-Lucent 9311 Macro V2 OD Alcatel-Lucent Proprietary 1-3
NN-20500-011 UA08.1 Use pursuant to applicable agreements
Issue 09.07 January 2013
Roadmap to Conventional Base Station documentation Roadmap to Conventional Base Station documentation
....................................................................................................................................................................................................................................
....................................................................................................................................................................................................................................
1-4 Alcatel-Lucent Proprietary Alcatel-Lucent 9311 Macro V2 OD
Use pursuant to applicable agreements NN-20500-011 UA08.1
Issue 09.07 January 2013
2 Safety statements
2
Overview
Purpose
This chapter provides information on the structure of safety statements which may arise
in the course of your work.
Contents
...................................................................................................................................................................................................................................
Alcatel-Lucent 9311 Macro V2 OD Alcatel-Lucent Proprietary 2-1
NN-20500-011 UA08.1 Use pursuant to applicable agreements
Issue 09.07 January 2013
Safety statements Structure of safety statements
....................................................................................................................................................................................................................................
General structure
Safety statements include the following structural elements:
B C D
CAUTION
MP L E
Lifting hazard E F
SA
Lifting this equipment by yourself can result in injury
due to the size and weight of the equipment.
G
Always use three people or a lifting device to transport
and position this equipment. [ABC123]
H
Item Structure element Purpose
1 Safety alert symbol Indicates the potential for personal injury
(optional)
2 Safety symbol Indicates hazard type (optional)
3 Signal word Indicates the severity of the hazard
4 Hazard type Describes the source of the risk of damage or
injury
5 Safety message Consequences if protective measures fail
6 Avoidance message Protective measures to take to avoid the hazard
7 Identifier The reference ID of the safety statement
(optional)
....................................................................................................................................................................................................................................
2-2 Alcatel-Lucent Proprietary Alcatel-Lucent 9311 Macro V2 OD
Use pursuant to applicable agreements NN-20500-011 UA08.1
Issue 09.07 January 2013
Safety statements Structure of safety statements
....................................................................................................................................................................................................................................
Signal words
The signal words identify the hazard severity levels as follows:
....................................................................................................................................................................................................................................
Alcatel-Lucent 9311 Macro V2 OD Alcatel-Lucent Proprietary 2-3
NN-20500-011 UA08.1 Use pursuant to applicable agreements
Issue 09.07 January 2013
Safety statements Structure of safety statements
....................................................................................................................................................................................................................................
....................................................................................................................................................................................................................................
2-4 Alcatel-Lucent Proprietary Alcatel-Lucent 9311 Macro V2 OD
Use pursuant to applicable agreements NN-20500-011 UA08.1
Issue 09.07 January 2013
3 3 orrective maintenance
C
activity
Overview
Purpose
This part describes the corrective maintenance activity applicable to the 9311 Macro OD
cabinets.
Contents
...................................................................................................................................................................................................................................
Alcatel-Lucent 9311 Macro V2 OD Alcatel-Lucent Proprietary 3-1
NN-20500-011 UA08.1 Use pursuant to applicable agreements
Issue 09.07 January 2013
Corrective maintenance activity Corrective maintenance activity
....................................................................................................................................................................................................................................
....................................................................................................................................................................................................................................
3-2 Alcatel-Lucent Proprietary Alcatel-Lucent 9311 Macro V2 OD
Use pursuant to applicable agreements NN-20500-011 UA08.1
Issue 09.07 January 2013
Corrective maintenance activity Corrective maintenance activity
....................................................................................................................................................................................................................................
....................................................................................................................................................................................................................................
Alcatel-Lucent 9311 Macro V2 OD Alcatel-Lucent Proprietary 3-3
NN-20500-011 UA08.1 Use pursuant to applicable agreements
Issue 09.07 January 2013
Corrective maintenance activity Corrective maintenance activity
....................................................................................................................................................................................................................................
....................................................................................................................................................................................................................................
3-4 Alcatel-Lucent Proprietary Alcatel-Lucent 9311 Macro V2 OD
Use pursuant to applicable agreements NN-20500-011 UA08.1
Issue 09.07 January 2013
Corrective maintenance activity Corrective maintenance activity
....................................................................................................................................................................................................................................
....................................................................................................................................................................................................................................
Alcatel-Lucent 9311 Macro V2 OD Alcatel-Lucent Proprietary 3-5
NN-20500-011 UA08.1 Use pursuant to applicable agreements
Issue 09.07 January 2013
Corrective maintenance activity Corrective maintenance activity
....................................................................................................................................................................................................................................
....................................................................................................................................................................................................................................
3-6 Alcatel-Lucent Proprietary Alcatel-Lucent 9311 Macro V2 OD
Use pursuant to applicable agreements NN-20500-011 UA08.1
Issue 09.07 January 2013
Corrective maintenance activity Corrective maintenance activity
....................................................................................................................................................................................................................................
....................................................................................................................................................................................................................................
Alcatel-Lucent 9311 Macro V2 OD Alcatel-Lucent Proprietary 3-7
NN-20500-011 UA08.1 Use pursuant to applicable agreements
Issue 09.07 January 2013
Corrective maintenance activity Corrective maintenance activity
....................................................................................................................................................................................................................................
Notes:
1. Manufacture Discontinue
Intervention restrictions
There may be a lapse of time between the identification of the alarm at the Access OAM
Graphic User Interface (GUI) and the time you arrive at the site.
You must be synchronized with the access network controller or system administrator (by
telephone) before an on-site intervention, in the following cases:
Isolating procedures
Completion of an on-site intervention
Return to service procedure
....................................................................................................................................................................................................................................
3-8 Alcatel-Lucent Proprietary Alcatel-Lucent 9311 Macro V2 OD
Use pursuant to applicable agreements NN-20500-011 UA08.1
Issue 09.07 January 2013
Corrective maintenance activity Corrective maintenance activity
....................................................................................................................................................................................................................................
Equipment safety instructions
The 9311 Macro V2 OD normally operates when the external temperature is between
-40C and +50C.
....................................................................................................................................................................................................................................
Alcatel-Lucent 9311 Macro V2 OD Alcatel-Lucent Proprietary 3-9
NN-20500-011 UA08.1 Use pursuant to applicable agreements
Issue 09.07 January 2013
Corrective maintenance activity Corrective maintenance activity
....................................................................................................................................................................................................................................
....................................................................................................................................................................................................................................
3-10 Alcatel-Lucent Proprietary Alcatel-Lucent 9311 Macro V2 OD
Use pursuant to applicable agreements NN-20500-011 UA08.1
Issue 09.07 January 2013
4 4311 Macro V2 OD
9
introduction
Overview
Purpose
This part gives an overview of the Alcatel-Lucent 9311Macro V2 Node B Outdoor
Contents
...................................................................................................................................................................................................................................
Alcatel-Lucent 9311 Macro V2 OD Alcatel-Lucent Proprietary 4-1
NN-20500-011 UA08.1 Use pursuant to applicable agreements
Issue 09.07 January 2013
9311 Macro V2 OD introduction 9311 Macro V2 OD introduction
....................................................................................................................................................................................................................................
....................................................................................................................................................................................................................................
4-2 Alcatel-Lucent Proprietary Alcatel-Lucent 9311 Macro V2 OD
Use pursuant to applicable agreements NN-20500-011 UA08.1
Issue 09.07 January 2013
9311 Macro V2 OD introduction 9311 Macro V2 OD introduction
....................................................................................................................................................................................................................................
The 9311 Macro V2 OD can operate into the following bandwidths:
2100 MHz
900 MHz
850 MHz
2100/900 MHz (dual-band)
2100/850 MHz (dual-band)
The following figure shows an outside view of the 9311 Macro V2 OD cabinet.
....................................................................................................................................................................................................................................
Alcatel-Lucent 9311 Macro V2 OD Alcatel-Lucent Proprietary 4-3
NN-20500-011 UA08.1 Use pursuant to applicable agreements
Issue 09.07 January 2013
9311 Macro V2 OD introduction 9311 Macro V2 OD introduction
....................................................................................................................................................................................................................................
9311 Macro V2 OD modules
The alpha-modules were the first generation of modules delivered by Alcatel-Lucent.
Note: The alpha-CEM is not supported since UA06.0.
Then Alcatel-Lucent delivered a second generation of modules:
iModules (also called beta-modules) and iModules-2
These modules are compatible with existing ones. They are transparent to the user as
they do not provide a capacity change (except for iCEM).
MCPA-2
The MCPA-2 module operates into the 2100 bandwidth.
The third generation of modules delivered by Alcatel-Lucent were the following:
xCCM
xCEM
xTRM
MCPA-3
The MCPA-3 module operates into the 2100 bandwidth.
The last generation of modules delivered by Alcatel-Lucent were the following:
xTRM-2
The latest xTRM generation. The xTRM-2 module operates into the 2100 bandwidth.
MCPA 60W
The latest MCPA generation. The MCPA 60W module operates into the 2100 MHz
and 850 MHz bandwidths.
SCPA 55W
The SCPA 55W module operates into the 900 MHz bandwidth.
DDM-E
The DDM-E module operates into the 900 MHz bandwidth.
DDM-P
The DDM-P module operates into the 900 MHz bandwidth.
eCEM
TRDU
The TRDU module operates into the 2100 bandwidth.
....................................................................................................................................................................................................................................
4-4 Alcatel-Lucent Proprietary Alcatel-Lucent 9311 Macro V2 OD
Use pursuant to applicable agreements NN-20500-011 UA08.1
Issue 09.07 January 2013
5 5311 Macro V2 OD
9
hardware presentation
Overview
Purpose
This part is a hardware presentation of the 9311 Macro V2 OD cabinet types.
Contents
...................................................................................................................................................................................................................................
Alcatel-Lucent 9311 Macro V2 OD Alcatel-Lucent Proprietary 5-1
NN-20500-011 UA08.1 Use pursuant to applicable agreements
Issue 09.07 January 2013
9311 Macro V2 OD hardware presentation 9311 Macro V2 OD hardware presentation
....................................................................................................................................................................................................................................
....................................................................................................................................................................................................................................
One Univity Compact Power System (UCPS) which houses the following modules:
One rectifier shelf (up to five rectifiers)
One DC Distribution Unit (DDU)
One Cabinet Control Unit (CCU)
one AC Distribution Unit (ADU)
The following figure shows the 9311 Macro V2 OD 2100. inside view and layout
....................................................................................................................................................................................................................................
Alcatel-Lucent 9311 Macro V2 OD Alcatel-Lucent Proprietary 5-3
NN-20500-011 UA08.1 Use pursuant to applicable agreements
Issue 09.07 January 2013
9311 Macro V2 OD hardware presentation 9311 Macro V2 OD hardware presentation
....................................................................................................................................................................................................................................
Figure 5-2 9311 Macro V2 OD general view with TRDU
....................................................................................................................................................................................................................................
5-4 Alcatel-Lucent Proprietary Alcatel-Lucent 9311 Macro V2 OD
Use pursuant to applicable agreements NN-20500-011 UA08.1
Issue 09.07 January 2013
9311 Macro V2 OD hardware presentation 9311 Macro V2 OD hardware presentation
....................................................................................................................................................................................................................................
Figure 5-3 9311 Macro V2 OD 2100 cabinet layout
Note: The ECU control box is located on the right side of the upper compartment (1).
The bulkhead allows cable connection and lightning protection.
The following figure shows the 9311 Macro V2 OD 2100 bulkhead.
....................................................................................................................................................................................................................................
Alcatel-Lucent 9311 Macro V2 OD Alcatel-Lucent Proprietary 5-5
NN-20500-011 UA08.1 Use pursuant to applicable agreements
Issue 09.07 January 2013
9311 Macro V2 OD hardware presentation 9311 Macro V2 OD hardware presentation
....................................................................................................................................................................................................................................
....................................................................................................................................................................................................................................
The DC input voltage range is -40.5 V up to -57 V DC with the following behaviors:
Limitation associated to the cabinet start up: the DC power supply voltage must be
higher than 52 V to start up the Node B.
Limitation associated to the LVD Threshold: the LVD Threshold is unchanged from
the AC version and is set to -44 V DC. The Node B operates only if the DC power
supply voltage is higher than -44 V at the entry of the Node B.
The following figure shows the inside view of the 9311 Macro V2 ODAC/DC variant.
....................................................................................................................................................................................................................................
Alcatel-Lucent 9311 Macro V2 OD Alcatel-Lucent Proprietary 5-7
NN-20500-011 UA08.1 Use pursuant to applicable agreements
Issue 09.07 January 2013
9311 Macro V2 OD hardware presentation 9311 Macro V2 OD hardware presentation
....................................................................................................................................................................................................................................
Note: The ECU control box is located on the right side of the upper compartment (1).
The checks and replacement procedures described for the standard AC powered
9311 Macro V2 OD cabinet also apply to the AC/DC variant of the 9311 Macro V2
ODcabinet.
....................................................................................................................................................................................................................................
5-8 Alcatel-Lucent Proprietary Alcatel-Lucent 9311 Macro V2 OD
Use pursuant to applicable agreements NN-20500-011 UA08.1
Issue 09.07 January 2013
9311 Macro V2 OD hardware presentation 9311 Macro V2 OD hardware presentation
....................................................................................................................................................................................................................................
When the cabinet is powered on and in operational state, the corporate LEDs of the UCPS
CCU module have the following behavior: C1 rectangular LED ON (green) and C2
triangular LED ON (red). This is a normal behavior, specific to the AC/DC variant.
....................................................................................................................................................................................................................................
Alcatel-Lucent 9311 Macro V2 OD Alcatel-Lucent Proprietary 5-9
NN-20500-011 UA08.1 Use pursuant to applicable agreements
Issue 09.07 January 2013
9311 Macro V2 OD hardware presentation 9311 Macro V2 OD hardware presentation
....................................................................................................................................................................................................................................
9311 Macro V2 OD 2100/850 hardware presentation
The 9311 Macro V2 OD 2100/850 hardware is similar to the 9311 Macro V2 OD 2100
hardware, with dedicated (bandwidth-specific) and shared modules:
Dedicated modules:
For 2100 MHz: TRM/iTRM/xTRM 2100 + MCPA/MCPA-2/MCPA-3/MCPA
60W 2100 + DDM/DDM-2 2100
For 850 MHz: TRM/iTRM/xTRM 850 + MCPA/MCPA 60W 850 + DDM 850
Shared modules: GPSAM, GPxOIM, iCEM/iCEM-2/xCEM/eCEM,
iCCM/iCCM-2/xCCM
....................................................................................................................................................................................................................................
5-10 Alcatel-Lucent Proprietary Alcatel-Lucent 9311 Macro V2 OD
Use pursuant to applicable agreements NN-20500-011 UA08.1
Issue 09.07 January 2013
6 Checking the door alarm
6
Overview
Purpose
This part describes how to check the door alarm.
Contents
...................................................................................................................................................................................................................................
Alcatel-Lucent 9311 Macro V2 OD Alcatel-Lucent Proprietary 6-1
NN-20500-011 UA08.1 Use pursuant to applicable agreements
Issue 09.07 January 2013
Checking the door alarm Checking the door alarm
....................................................................................................................................................................................................................................
Intervention time
Two minutes
Tools required
None
Important! This procedure requires to be in contact with the OMC administrator.
Important! For outdoor models, do not forget to ask the site manager for the Node B
key.
Procedure
...................................................................................................................................................................................................
1 Contact the OMC administrator to check that the door alarm is OFF.
...................................................................................................................................................................................................
3 An alarm must be observed at the OMC. Request confirmation from the OMC
administrator.
...................................................................................................................................................................................................
5 Check with the OMC administrator that the door alarm is OFF.
E...................................................................................................................................................................................................
N D O F S T E P S
....................................................................................................................................................................................................................................
6-2 Alcatel-Lucent Proprietary Alcatel-Lucent 9311 Macro V2 OD
Use pursuant to applicable agreements NN-20500-011 UA08.1
Issue 09.07 January 2013
7 7311 Macro V2 OD power
9
down and power up
procedures
Overview
Purpose
This part describes how to power down and power up the 9311 Macro V2 OD cabinets.
Contents
...................................................................................................................................................................................................................................
Alcatel-Lucent 9311 Macro V2 OD Alcatel-Lucent Proprietary 7-1
NN-20500-011 UA08.1 Use pursuant to applicable agreements
Issue 09.07 January 2013
9311 Macro V2 OD power down and power up procedures Powering down a 9311 Macro V2 OD
....................................................................................................................................................................................................................................
Preliminary operations
Make sure the state of the btsSiteManager object is "locked". For more information about
the OMC, please refer to Alcatel-Lucent 9353 Wireless Management System - User
Guide, NN-20500-032.
NOTICE
Service-disruption hazard
This procedure will result in service disruption. Notify the OMC administrator of a
service outage before commencing.
Important! Do not forget to ask the site manager for the Node B key.
Important! If an AC power down is required, notify the site manager then locate the
ac power supply on the customer site. Disconnect and lock out the AC main power
supply before servicing the equipment.
Procedure
...................................................................................................................................................................................................
2 Switch OFF the four DDU circuit breakers in the following order:
DIGITAL/RICO/USER ICO
RF0 and RF1
ECU
Note: To locate DDU circuit breakers, see legend 8 in Figure 5-3, 9311 Macro V2
OD 2100 cabinet layout (p. 5-5)
...................................................................................................................................................................................................
....................................................................................................................................................................................................................................
Note: To locate ADU circuit breakers, see legend 5 in Figure 5-3, 9311 Macro V2
OD 2100 cabinet layout (p. 5-5)
...................................................................................................................................................................................................
5 At the customer AC power supply, switch OFF the cabinet circuit breaker.
...................................................................................................................................................................................................
....................................................................................................................................................................................................................................
Alcatel-Lucent 9311 Macro V2 OD Alcatel-Lucent Proprietary 7-3
NN-20500-011 UA08.1 Use pursuant to applicable agreements
Issue 09.07 January 2013
9311 Macro V2 OD power down and power up procedures Powering up a 9311 Macro V2 OD
....................................................................................................................................................................................................................................
Tools required
Local Installation Terminal (TIL)
Preliminary operations
Open the Node B doors and check the following:
The three ADU circuit breakers are switched OFF.
See legend 5 in Figure 5-3, 9311 Macro V2 OD 2100 cabinet layout (p. 5-5).
The four DDU circuit breakers are switched OFF.
See legend 8 in Figure 5-3, 9311 Macro V2 OD 2100 cabinet layout (p. 5-5).
The battery circuit breaker below the UCPS is switched OFF.
See legend 10 in Figure 5-3, 9311 Macro V2 OD 2100 cabinet layout (p. 5-5).
Important! This procedure requires to be in contact with the OMC administrator.
Important! Do not forget to ask the site manager for the Node B key.
Important! On the customer site, locate the AC power supply and notify the site
manager of the Node B start up.
Procedure
...................................................................................................................................................................................................
3 Check that the green LED on each rectifier front face is lit, as well as the green LED on
the CCU.
...................................................................................................................................................................................................
....................................................................................................................................................................................................................................
7-4 Alcatel-Lucent Proprietary Alcatel-Lucent 9311 Macro V2 OD
Use pursuant to applicable agreements NN-20500-011 UA08.1
Issue 09.07 January 2013
9311 Macro V2 OD power down and power up procedures Powering up a 9311 Macro V2 OD
....................................................................................................................................................................................................................................
...................................................................................................................................................................................................
6 In the upper compartment of the cabinet, check that the LEDs of the ECU control module
are lit.
Note: If the temperature is around freezing point or below, close the doors to warm up
the Node B.
...................................................................................................................................................................................................
10 Check that the green LEDs on the CCM, GPSAM, and DDM modules are lit.
...................................................................................................................................................................................................
11 If battery back-up is used, and only if the green LED on the CCU is lit, switch ON the
battery circuit breaker below the UCPS.
...................................................................................................................................................................................................
12 Check on the TIL and with the OMC administrator that the Node B is operational.
...................................................................................................................................................................................................
....................................................................................................................................................................................................................................
Alcatel-Lucent 9311 Macro V2 OD Alcatel-Lucent Proprietary 7-5
NN-20500-011 UA08.1 Use pursuant to applicable agreements
Issue 09.07 January 2013
9311 Macro V2 OD power down and power up procedures Powering up a 9311 Macro V2 OD
....................................................................................................................................................................................................................................
....................................................................................................................................................................................................................................
7-6 Alcatel-Lucent Proprietary Alcatel-Lucent 9311 Macro V2 OD
Use pursuant to applicable agreements NN-20500-011 UA08.1
Issue 09.07 January 2013
8 8311 Macro V2 OD
9
corrective maintenance
procedures
Overview
Purpose
This part contains the replacement procedures applicable to the 9311 Macro V2 OD.
Contents
...................................................................................................................................................................................................................................
Alcatel-Lucent 9311 Macro V2 OD Alcatel-Lucent Proprietary 8-1
NN-20500-011 UA08.1 Use pursuant to applicable agreements
Issue 09.07 January 2013
9311 Macro V2 OD corrective maintenance procedures Overview
....................................................................................................................................................................................................................................
....................................................................................................................................................................................................................................
8-2 Alcatel-Lucent Proprietary Alcatel-Lucent 9311 Macro V2 OD
Use pursuant to applicable agreements NN-20500-011 UA08.1
Issue 09.07 January 2013
9311 Macro V2 OD corrective maintenance procedures Overview
Replacing the digital shelf equipment
....................................................................................................................................................................................................................................
Overview
Purpose
This section presents the replacement procedures applicable to the digital shelf
Contents
....................................................................................................................................................................................................................................
Alcatel-Lucent 9311 Macro V2 OD Alcatel-Lucent Proprietary 8-3
NN-20500-011 UA08.1 Use pursuant to applicable agreements
Issue 09.07 January 2013
9311 Macro V2 OD corrective maintenance procedures Replacing the Channel Element Module (CEM)
Replacing the digital shelf equipment
....................................................................................................................................................................................................................................
Intervention time
Ten minutes
Tools required
Screwdriver
Local Installation Terminal (TIL)
....................................................................................................................................................................................................................................
8-4 Alcatel-Lucent Proprietary Alcatel-Lucent 9311 Macro V2 OD
Use pursuant to applicable agreements NN-20500-011 UA08.1
Issue 09.07 January 2013
9311 Macro V2 OD corrective maintenance procedures Replacing the Channel Element Module (CEM)
Replacing the digital shelf equipment
....................................................................................................................................................................................................................................
....................................................................................................................................................................................................................................
Alcatel-Lucent 9311 Macro V2 OD Alcatel-Lucent Proprietary 8-5
NN-20500-011 UA08.1 Use pursuant to applicable agreements
Issue 09.07 January 2013
9311 Macro V2 OD corrective maintenance procedures Replacing the Channel Element Module (CEM)
Replacing the digital shelf equipment
....................................................................................................................................................................................................................................
Figure 8-2 iCEM-2 64 front panel
....................................................................................................................................................................................................................................
8-6 Alcatel-Lucent Proprietary Alcatel-Lucent 9311 Macro V2 OD
Use pursuant to applicable agreements NN-20500-011 UA08.1
Issue 09.07 January 2013
9311 Macro V2 OD corrective maintenance procedures Replacing the Channel Element Module (CEM)
Replacing the digital shelf equipment
....................................................................................................................................................................................................................................
Figure 8-3 iCEM 128 front panel
....................................................................................................................................................................................................................................
Alcatel-Lucent 9311 Macro V2 OD Alcatel-Lucent Proprietary 8-7
NN-20500-011 UA08.1 Use pursuant to applicable agreements
Issue 09.07 January 2013
9311 Macro V2 OD corrective maintenance procedures Replacing the Channel Element Module (CEM)
Replacing the digital shelf equipment
....................................................................................................................................................................................................................................
Figure 8-4 iCEM-2 128 front panel
....................................................................................................................................................................................................................................
8-8 Alcatel-Lucent Proprietary Alcatel-Lucent 9311 Macro V2 OD
Use pursuant to applicable agreements NN-20500-011 UA08.1
Issue 09.07 January 2013
9311 Macro V2 OD corrective maintenance procedures Replacing the Channel Element Module (CEM)
Replacing the digital shelf equipment
....................................................................................................................................................................................................................................
Figure 8-5 xCEM front panel
....................................................................................................................................................................................................................................
Alcatel-Lucent 9311 Macro V2 OD Alcatel-Lucent Proprietary 8-9
NN-20500-011 UA08.1 Use pursuant to applicable agreements
Issue 09.07 January 2013
9311 Macro V2 OD corrective maintenance procedures Replacing the Channel Element Module (CEM)
Replacing the digital shelf equipment
....................................................................................................................................................................................................................................
Figure 8-6 eCEM front panel
....................................................................................................................................................................................................................................
8-10 Alcatel-Lucent Proprietary Alcatel-Lucent 9311 Macro V2 OD
Use pursuant to applicable agreements NN-20500-011 UA08.1
Issue 09.07 January 2013
9311 Macro V2 OD corrective maintenance procedures Replacing the Channel Element Module (CEM)
Replacing the digital shelf equipment
....................................................................................................................................................................................................................................
NOTICE
ESD hazard
We recommend wearing an antistatic bracelet connected to ground via a protective
resistance to avoid damaging circuits when handling printed circuits.
Electronic boards must be stored in antistatic envelopes or inside packages both during
transportation and storage.
Important! Notify the OMC administrator in case of service outage or reduction.
Important! If the defective CEM is configured in HSDPA mode, the procedure to
replace it may trigger an alarm "NO HSDPA HARDWARE RECOVERY
INFORMATION" on the OMC-R (RNC side). For information on how to recover an
HSDPA capability, refer to Alcatel-Lucent 9300 W-CDMA Product Family - RNC and
MSS POC Alarms Reference, NN-20500-024.
Procedure
...................................................................................................................................................................................................
2 Locate the faulty CEM in the digital shelf: its red triangular LED is lit.
...................................................................................................................................................................................................
3 Ask the OMC administrator to lock the faulty cem object at the OMC (through Set
Administrative State). For more information, please refer to Alcatel-Lucent 9353 Wireless
Management System - User Guide, NN-20500-032.
...................................................................................................................................................................................................
5 Remove the defective CEM using the front panel handle (1).
...................................................................................................................................................................................................
7 Insert the new CEM into the digital shelf, in the same slot as the defective CEM.
...................................................................................................................................................................................................
....................................................................................................................................................................................................................................
Alcatel-Lucent 9311 Macro V2 OD Alcatel-Lucent Proprietary 8-11
NN-20500-011 UA08.1 Use pursuant to applicable agreements
Issue 09.07 January 2013
9311 Macro V2 OD corrective maintenance procedures Replacing the Channel Element Module (CEM)
Replacing the digital shelf equipment
....................................................................................................................................................................................................................................
...................................................................................................................................................................................................
9 Ask the OMC administrator to unlock the cem object previously locked on step 3.
...................................................................................................................................................................................................
10 Note: If the new CEM module requires a manual upgrade from the TIL, and if it is
used without being upgraded, it will run out of service.
Depending on the spare release and the OAM release, an intermediary manual upgrade
through the TIL might be necessary (see table below). For more information on how to
upgrade manually a CEM, refer to Alcatel-Lucent 9100 and 93xx Node B -
Commissioning and Fault Management User Manual: TIL, NN-20500-019.
12 Check on the TIL and with the OMC administrator that the Node B is operational.
...................................................................................................................................................................................................
....................................................................................................................................................................................................................................
8-12 Alcatel-Lucent Proprietary Alcatel-Lucent 9311 Macro V2 OD
Use pursuant to applicable agreements NN-20500-011 UA08.1
Issue 09.07 January 2013
9311 Macro V2 OD corrective maintenance procedures Replacing the Core Controller Module (CCM)
Replacing the digital shelf equipment
....................................................................................................................................................................................................................................
Intervention time
Ten minutes
Tools required
Screwdriver
Extraction handle (3JR08430AA)
Local Installation Terminal (TIL)
....................................................................................................................................................................................................................................
Alcatel-Lucent 9311 Macro V2 OD Alcatel-Lucent Proprietary 8-13
NN-20500-011 UA08.1 Use pursuant to applicable agreements
Issue 09.07 January 2013
9311 Macro V2 OD corrective maintenance procedures Replacing the Core Controller Module (CCM)
Replacing the digital shelf equipment
....................................................................................................................................................................................................................................
....................................................................................................................................................................................................................................
8-14 Alcatel-Lucent Proprietary Alcatel-Lucent 9311 Macro V2 OD
Use pursuant to applicable agreements NN-20500-011 UA08.1
Issue 09.07 January 2013
9311 Macro V2 OD corrective maintenance procedures Replacing the Core Controller Module (CCM)
Replacing the digital shelf equipment
....................................................................................................................................................................................................................................
Figure 8-8 iCCM front panel
....................................................................................................................................................................................................................................
Alcatel-Lucent 9311 Macro V2 OD Alcatel-Lucent Proprietary 8-15
NN-20500-011 UA08.1 Use pursuant to applicable agreements
Issue 09.07 January 2013
9311 Macro V2 OD corrective maintenance procedures Replacing the Core Controller Module (CCM)
Replacing the digital shelf equipment
....................................................................................................................................................................................................................................
Figure 8-9 iCCM-2 front panel
....................................................................................................................................................................................................................................
8-16 Alcatel-Lucent Proprietary Alcatel-Lucent 9311 Macro V2 OD
Use pursuant to applicable agreements NN-20500-011 UA08.1
Issue 09.07 January 2013
9311 Macro V2 OD corrective maintenance procedures Replacing the Core Controller Module (CCM)
Replacing the digital shelf equipment
....................................................................................................................................................................................................................................
Figure 8-10 xCCM front panel in configuration xCCM-4E1
....................................................................................................................................................................................................................................
Alcatel-Lucent 9311 Macro V2 OD Alcatel-Lucent Proprietary 8-17
NN-20500-011 UA08.1 Use pursuant to applicable agreements
Issue 09.07 January 2013
9311 Macro V2 OD corrective maintenance procedures Replacing the Core Controller Module (CCM)
Replacing the digital shelf equipment
....................................................................................................................................................................................................................................
Figure 8-11 xCCM front panel in configuration xCCM-GE
....................................................................................................................................................................................................................................
8-18 Alcatel-Lucent Proprietary Alcatel-Lucent 9311 Macro V2 OD
Use pursuant to applicable agreements NN-20500-011 UA08.1
Issue 09.07 January 2013
9311 Macro V2 OD corrective maintenance procedures Replacing the Core Controller Module (CCM)
Replacing the digital shelf equipment
....................................................................................................................................................................................................................................
NOTICE
ESD hazard
Electronic components can be destroyed by electrostatic discharge (ESD). Hold circuit
packs only at the edges or on the insertion and removal facilities. Always observe the
general ESD instructions.
Important! Notify the OMC administrator in case of service outage or reduction.
Procedure
...................................................................................................................................................................................................
2 NOTICE
Service-disruption hazard
Following the procedure below will result in a loss of service.
Ask the OMC administrator to lock all objects (through Set Administrative State)
associated with Remote Radio devices connected to this faulty CCM. For more
information, please refer to Alcatel-Lucent 9353 Wireless Management System - User
Guide, NN-20500-032.
...................................................................................................................................................................................................
4 Case 1: On the CCM/iCCM/iCCM-2 front panel, disconnect the E1/T1 connector (PCM
link).
or
Case 2: On the xCCM (in the configuration xCCM-4E1) front panel, disconnect the two
E1/T1 connectors (PCM and MDA links) and the Ethernet connector (port1) if hybrid Iub
is implemented.
or
Case 3: On the xCCM (in the configuration xCCM-GE) front panel, disconnect the Giga
Ethernet connector (MDA links).
...................................................................................................................................................................................................
5 Case 1: If you replace a CCM, loosen the two CCM module screws. (See legend 2 on
Figure 8-7, CCM front panel (p. 8-14).)
or
....................................................................................................................................................................................................................................
Alcatel-Lucent 9311 Macro V2 OD Alcatel-Lucent Proprietary 8-19
NN-20500-011 UA08.1 Use pursuant to applicable agreements
Issue 09.07 January 2013
9311 Macro V2 OD corrective maintenance procedures Replacing the Core Controller Module (CCM)
Replacing the digital shelf equipment
....................................................................................................................................................................................................................................
Case 2: If you replace an iCCM/iCCM-2/xCCM, only its board needs to be replaced. In
that case, loosen the two iCCM/iCCM-2/xCCM board screws. (See legend 2 on Figure
8-9, iCCM-2 front panel (p. 8-16) or legend 10 on Figure 8-10, xCCM front panel in
configuration xCCM-4E1 (p. 8-17).)
...................................................................................................................................................................................................
6 Case 1: Remove the defective CCM using the front panel handle.
or
Case 2: Remove the defective iCCM/iCCM-2/xCCM using the extraction handle. (See
Tools required (p. 8-13).)
...................................................................................................................................................................................................
7 Case 1: If you replace a CCM by another CCM, insert the new CCM into the digital
shelf, in the same slot as the defective CCM.
or
Case 2: If you replace a CCM by an iCCM/iCCM-2, insert the new iCCM/iCCM-2
module (board + filler) into the digital shelf, in the same slot as the defective CCM.
or
Case 3: If you replace an iCCM/iCCM-2/xCCM by an iCCM/iCCM-2/xCCM, insert the
new iCCM/iCCM-2/xCCM board into the digital shelf, in the same dual slot as the
defective iCCM/iCCM-2/xCCM board.
...................................................................................................................................................................................................
8 Depending on the case, tighten the two CCM front module screws or the two
iCCM/iCCM-2/xCCM front board screws.
...................................................................................................................................................................................................
11 Note: If the new CCM module requires a manual upgrade from the TIL, and if it is
used without being upgraded, it will run out of service.
Depending on the spare release and the OAM software release, an intermediary upgrade
through the TIL might be necessary.
....................................................................................................................................................................................................................................
8-20 Alcatel-Lucent Proprietary Alcatel-Lucent 9311 Macro V2 OD
Use pursuant to applicable agreements NN-20500-011 UA08.1
Issue 09.07 January 2013
9311 Macro V2 OD corrective maintenance procedures Replacing the Core Controller Module (CCM)
Replacing the digital shelf equipment
....................................................................................................................................................................................................................................
Upgrade the software, if necessary, according to the table below. For more information on
how to upgrade the CCM module through the TIL, refer to Alcatel-Lucent 9100 and 93xx
Node B - Commissioning and Fault Management User Manual: TIL, NN-20500-019.
The second upgrade is done by the OMC-B, automatically.
...................................................................................................................................................................................................
13 Ask the OMC administrator to unlock the objects previously locked on step 2.
...................................................................................................................................................................................................
14 Check the MCA module with the TIL. For more information, refer to the TIL main
window and the GPSAM module in Alcatel-Lucent 9100 and 93xx Node B -
Commissioning and Fault Management User Manual: TIL, NN-20500-019.
....................................................................................................................................................................................................................................
Alcatel-Lucent 9311 Macro V2 OD Alcatel-Lucent Proprietary 8-21
NN-20500-011 UA08.1 Use pursuant to applicable agreements
Issue 09.07 January 2013
9311 Macro V2 OD corrective maintenance procedures Replacing the Core Controller Module (CCM)
Replacing the digital shelf equipment
....................................................................................................................................................................................................................................
...................................................................................................................................................................................................
16 Check on the TIL and with the OMC administrator that the Node B is operational.
...................................................................................................................................................................................................
....................................................................................................................................................................................................................................
8-22 Alcatel-Lucent Proprietary Alcatel-Lucent 9311 Macro V2 OD
Use pursuant to applicable agreements NN-20500-011 UA08.1
Issue 09.07 January 2013
9311 Macro V2 OD corrective maintenance procedures Replacing the GPS interface and Alarm Module (GPSAM)
Replacing the digital shelf equipment
....................................................................................................................................................................................................................................
Intervention time
Ten minutes
Tools required
Screwdriver
....................................................................................................................................................................................................................................
Alcatel-Lucent 9311 Macro V2 OD Alcatel-Lucent Proprietary 8-23
NN-20500-011 UA08.1 Use pursuant to applicable agreements
Issue 09.07 January 2013
9311 Macro V2 OD corrective maintenance procedures Replacing the GPS interface and Alarm Module (GPSAM)
Replacing the digital shelf equipment
....................................................................................................................................................................................................................................
....................................................................................................................................................................................................................................
8-24 Alcatel-Lucent Proprietary Alcatel-Lucent 9311 Macro V2 OD
Use pursuant to applicable agreements NN-20500-011 UA08.1
Issue 09.07 January 2013
9311 Macro V2 OD corrective maintenance procedures Replacing the GPS interface and Alarm Module (GPSAM)
Replacing the digital shelf equipment
....................................................................................................................................................................................................................................
NOTICE
ESD hazard
Electronic components can be destroyed by electrostatic discharge (ESD). Hold circuit
packs only at the edges or on the insertion and removal facilities. Always observe the
general ESD instructions.
Procedure
...................................................................................................................................................................................................
2 Locate the faulty GPSAM on the right-hand side of the digital shelf.
...................................................................................................................................................................................................
6 Remove the defective GPSAM using the front panel handle (1).
...................................................................................................................................................................................................
8 Reconnect the digital cable to the front of the GPSAM, in the "Internal bus" slot.
...................................................................................................................................................................................................
11 To power up the digital shelf, switch ON the Digital circuit breaker on the DC power
system shelf.
....................................................................................................................................................................................................................................
Alcatel-Lucent 9311 Macro V2 OD Alcatel-Lucent Proprietary 8-25
NN-20500-011 UA08.1 Use pursuant to applicable agreements
Issue 09.07 January 2013
9311 Macro V2 OD corrective maintenance procedures Replacing the GPS interface and Alarm Module (GPSAM)
Replacing the digital shelf equipment
....................................................................................................................................................................................................................................
Result: The GPSAM will go through a power-up sequence.
...................................................................................................................................................................................................
12 Check the state of the LEDs. They should go on, then take the following states:
Result: Red triangular LED OFF, green rectangular LED ON
...................................................................................................................................................................................................
....................................................................................................................................................................................................................................
8-26 Alcatel-Lucent Proprietary Alcatel-Lucent 9311 Macro V2 OD
Use pursuant to applicable agreements NN-20500-011 UA08.1
Issue 09.07 January 2013
9311 Macro V2 OD corrective maintenance procedures Replacing the TRansceiver Module (TRM)
Replacing the digital shelf equipment
....................................................................................................................................................................................................................................
Intervention time
Ten minutes
Tools required
Screwdriver
SMA torque wrench
Local Installation Terminal (TIL)
....................................................................................................................................................................................................................................
Alcatel-Lucent 9311 Macro V2 OD Alcatel-Lucent Proprietary 8-27
NN-20500-011 UA08.1 Use pursuant to applicable agreements
Issue 09.07 January 2013
9311 Macro V2 OD corrective maintenance procedures Replacing the TRansceiver Module (TRM)
Replacing the digital shelf equipment
....................................................................................................................................................................................................................................
....................................................................................................................................................................................................................................
8-28 Alcatel-Lucent Proprietary Alcatel-Lucent 9311 Macro V2 OD
Use pursuant to applicable agreements NN-20500-011 UA08.1
Issue 09.07 January 2013
9311 Macro V2 OD corrective maintenance procedures Replacing the TRansceiver Module (TRM)
Replacing the digital shelf equipment
....................................................................................................................................................................................................................................
Figure 8-14 iTRM front panel
....................................................................................................................................................................................................................................
Alcatel-Lucent 9311 Macro V2 OD Alcatel-Lucent Proprietary 8-29
NN-20500-011 UA08.1 Use pursuant to applicable agreements
Issue 09.07 January 2013
9311 Macro V2 OD corrective maintenance procedures Replacing the TRansceiver Module (TRM)
Replacing the digital shelf equipment
....................................................................................................................................................................................................................................
Figure 8-15 xTRM front panel
....................................................................................................................................................................................................................................
8-30 Alcatel-Lucent Proprietary Alcatel-Lucent 9311 Macro V2 OD
Use pursuant to applicable agreements NN-20500-011 UA08.1
Issue 09.07 January 2013
9311 Macro V2 OD corrective maintenance procedures Replacing the TRansceiver Module (TRM)
Replacing the digital shelf equipment
....................................................................................................................................................................................................................................
Figure 8-16 xTRM-2 front panel
....................................................................................................................................................................................................................................
Alcatel-Lucent 9311 Macro V2 OD Alcatel-Lucent Proprietary 8-31
NN-20500-011 UA08.1 Use pursuant to applicable agreements
Issue 09.07 January 2013
9311 Macro V2 OD corrective maintenance procedures Replacing the TRansceiver Module (TRM)
Replacing the digital shelf equipment
....................................................................................................................................................................................................................................
NOTICE
ESD hazard
We recommend wearing an antistatic bracelet connected to ground via a protective
resistance to avoid damaging circuits when handling printed circuits.
Electronic boards must be stored in antistatic envelopes or inside packages both during
transportation and storage.
NOTICE
Service-disruption hazard
This procedure will result in service disruption. Notify the OMC administrator of a
service outage before commencing.
Important! Precautions to be observed when plugging/unplugging the TRM Rx
connector
The TRM Rx connector (coaxpack) is very sensitive in the Node B design,
contributing to the global quality reception. It has therefore to be treated with care
when removed or replaced for maintenance purpose.
Ensure at any time its correct alignment with guides, the lock system being placed
on the left.
Ensure the lock system operates properly.
Do not apply force when inserting it.
Ensure a perfect straight angle with the TRM front panel.
If tie-raps are applied to secure the cable within the cabinet, ensure they are not
putting any constraint to that connector.
Important! The tightening torque of the front panel screws must be 0.25 N.m (0.2375
N.m to 0.2625 N.m).
The SMA tightening torque must be 0.8 N.m to 1.2 N.m.
Procedure
...................................................................................................................................................................................................
2 Locate the faulty TRM in the digital shelf: its red triangular LED is lit.
...................................................................................................................................................................................................
3 Ask the OMC administrator to lock the faulty trm object at the OMC (by Set
Administrative State). For more information, please refer to Alcatel-Lucent 9353 Wireless
Management System - User Guide, NN-20500-032.
....................................................................................................................................................................................................................................
8-32 Alcatel-Lucent Proprietary Alcatel-Lucent 9311 Macro V2 OD
Use pursuant to applicable agreements NN-20500-011 UA08.1
Issue 09.07 January 2013
9311 Macro V2 OD corrective maintenance procedures Replacing the TRansceiver Module (TRM)
Replacing the digital shelf equipment
....................................................................................................................................................................................................................................
...................................................................................................................................................................................................
7 Remove the defective TRM using the front panel handle (1).
...................................................................................................................................................................................................
13 Note: If the new TRM module requires a manual upgrade at the TIL, and if it is used
without being upgraded, it will run out of service.
Depending on the spare release and on the OAM release, an intermediary upgrade might
be necessary through the TIL.
....................................................................................................................................................................................................................................
Alcatel-Lucent 9311 Macro V2 OD Alcatel-Lucent Proprietary 8-33
NN-20500-011 UA08.1 Use pursuant to applicable agreements
Issue 09.07 January 2013
9311 Macro V2 OD corrective maintenance procedures Replacing the TRansceiver Module (TRM)
Replacing the digital shelf equipment
....................................................................................................................................................................................................................................
Upgrade the software, if necessary according to the table below. For more information on
how to upgrade the TRM through the TIL, refer to Alcatel-Lucent 9100 and 93xx Node B
- Commissioning and Fault Management User Manual: TIL, NN-20500-019.
The second upgrade is done by the OMC-B automatically.
...................................................................................................................................................................................................
15 Ask the OMC administrator to unlock the trm object previously locked in step 3.
...................................................................................................................................................................................................
16 Check the state of the LEDs. They should go on, then take the following states.
Result: Red triangular LED OFF, green triangular LED ON
...................................................................................................................................................................................................
17 Check on the TIL and with the OMC administrator that the Node B is operational.
...................................................................................................................................................................................................
....................................................................................................................................................................................................................................
8-34 Alcatel-Lucent Proprietary Alcatel-Lucent 9311 Macro V2 OD
Use pursuant to applicable agreements NN-20500-011 UA08.1
Issue 09.07 January 2013
9311 Macro V2 OD corrective maintenance procedures Replacing the GPxOIM
Replacing the digital shelf equipment
....................................................................................................................................................................................................................................
Intervention time
Ten minutes
Tools required
Screwdriver
Extraction handle (P/N: P0850747)
....................................................................................................................................................................................................................................
Alcatel-Lucent 9311 Macro V2 OD Alcatel-Lucent Proprietary 8-35
NN-20500-011 UA08.1 Use pursuant to applicable agreements
Issue 09.07 January 2013
9311 Macro V2 OD corrective maintenance procedures Replacing the GPxOIM
Replacing the digital shelf equipment
....................................................................................................................................................................................................................................
NOTICE
Service-disruption hazard
This procedure will result in service disruption. Notify the OMC administrator of a
service outage before commencing.
....................................................................................................................................................................................................................................
8-36 Alcatel-Lucent Proprietary Alcatel-Lucent 9311 Macro V2 OD
Use pursuant to applicable agreements NN-20500-011 UA08.1
Issue 09.07 January 2013
9311 Macro V2 OD corrective maintenance procedures Replacing the GPxOIM
Replacing the digital shelf equipment
....................................................................................................................................................................................................................................
NOTICE
ESD hazard
Electronic components can be destroyed by electrostatic discharge (ESD). Hold circuit
packs only at the edges or on the insertion and removal facilities. Always observe the
general ESD instructions.
Procedure
...................................................................................................................................................................................................
2 Locate the faulty GPxOIM on the right-hand side of the digital shelf: its red triangular
LED is lit. (See Figure 5-3, 9311 Macro V2 OD 2100 cabinet layout (p. 5-5))
...................................................................................................................................................................................................
3 NOTICE
Service-disruption hazard
Following the procedure below will result in a loss of service.
Ask the OMC administrator to lock (by Set Administrative State) all objects associated
with the RRH modules connected to the faulty GPxOIM. For more information, refer to
Alcatel-Lucent 9353 Wireless Management System - User Guide, NN-20500-032.
...................................................................................................................................................................................................
4 Disconnect the two optical fibers from the C2OIM front panel.
...................................................................................................................................................................................................
5 Disconnect the digital cable ("Internal Bus" connector) from the GPxOIM front panel.
...................................................................................................................................................................................................
7 Extract the C2OIM from the GPxOIM mechanics using the extraction handle.
...................................................................................................................................................................................................
8 Unscrew the two front panel screws located at the top and at the bottom of the 50-mm
GPxOIM mechanics (1).
...................................................................................................................................................................................................
....................................................................................................................................................................................................................................
Alcatel-Lucent 9311 Macro V2 OD Alcatel-Lucent Proprietary 8-37
NN-20500-011 UA08.1 Use pursuant to applicable agreements
Issue 09.07 January 2013
9311 Macro V2 OD corrective maintenance procedures Replacing the GPxOIM
Replacing the digital shelf equipment
....................................................................................................................................................................................................................................
...................................................................................................................................................................................................
13 Select the "Base" position for the three-position switch on the GPxOIM front panel.
...................................................................................................................................................................................................
...................................................................................................................................................................................................
17 Ask the OMC administrator to unlock the objects previously locked on step 3.
....................................................................................................................................................................................................................................
8-38 Alcatel-Lucent Proprietary Alcatel-Lucent 9311 Macro V2 OD
Use pursuant to applicable agreements NN-20500-011 UA08.1
Issue 09.07 January 2013
9311 Macro V2 OD corrective maintenance procedures Replacing the GPxOIM
Replacing the digital shelf equipment
....................................................................................................................................................................................................................................
...................................................................................................................................................................................................
18 Check the state of the LEDs. They should turn on, then take the following states:
On the GPxOIM, red triangular LED OFF and green rectangular LED ON
On the C2OIM, Tx Act and Rx Act green LEDs ON
...................................................................................................................................................................................................
....................................................................................................................................................................................................................................
Alcatel-Lucent 9311 Macro V2 OD Alcatel-Lucent Proprietary 8-39
NN-20500-011 UA08.1 Use pursuant to applicable agreements
Issue 09.07 January 2013
9311 Macro V2 OD corrective maintenance procedures Replacing the C2OIM
Replacing the digital shelf equipment
....................................................................................................................................................................................................................................
Intervention time
Five minutes
Tools required
Screwdriver
Extraction handle (P/N: P0850747)
....................................................................................................................................................................................................................................
8-40 Alcatel-Lucent Proprietary Alcatel-Lucent 9311 Macro V2 OD
Use pursuant to applicable agreements NN-20500-011 UA08.1
Issue 09.07 January 2013
9311 Macro V2 OD corrective maintenance procedures Replacing the C2OIM
Replacing the digital shelf equipment
....................................................................................................................................................................................................................................
....................................................................................................................................................................................................................................
Alcatel-Lucent 9311 Macro V2 OD Alcatel-Lucent Proprietary 8-41
NN-20500-011 UA08.1 Use pursuant to applicable agreements
Issue 09.07 January 2013
9311 Macro V2 OD corrective maintenance procedures Replacing the C2OIM
Replacing the digital shelf equipment
....................................................................................................................................................................................................................................
Figure 8-20 C2OIM-GS front panel
NOTICE
Service-disruption hazard
This procedure will result in service disruption. Notify the OMC administrator of a
service outage before commencing.
....................................................................................................................................................................................................................................
8-42 Alcatel-Lucent Proprietary Alcatel-Lucent 9311 Macro V2 OD
Use pursuant to applicable agreements NN-20500-011 UA08.1
Issue 09.07 January 2013
9311 Macro V2 OD corrective maintenance procedures Replacing the C2OIM
Replacing the digital shelf equipment
....................................................................................................................................................................................................................................
NOTICE
ESD hazard
Electronic components can be destroyed by electrostatic discharge (ESD). Hold circuit
packs only at the edges or on the insertion and removal facilities. Always observe the
general ESD instructions.
Procedure
...................................................................................................................................................................................................
2 Locate the faulty C2OIM on the right-hand side of the digital shelf: its red triangular LED
is lit. (See Figure 5-3, 9311 Macro V2 OD 2100 cabinet layout (p. 5-5))
...................................................................................................................................................................................................
3 NOTICE
Service-disruption hazard
Following the procedure below will result in a loss of service.
Ask the OMC administrator to lock all optical link objects (by Set Administrative State).
For more information, refer to Alcatel-Lucent 9353 Wireless Management System - User
Guide, NN-20500-032.
...................................................................................................................................................................................................
4 Disconnect the two optical fibers from the C2OIM front panel.
...................................................................................................................................................................................................
6 Extract the defective C2OIM from the GPxOIM mechanics using the extraction handle.
...................................................................................................................................................................................................
....................................................................................................................................................................................................................................
Alcatel-Lucent 9311 Macro V2 OD Alcatel-Lucent Proprietary 8-43
NN-20500-011 UA08.1 Use pursuant to applicable agreements
Issue 09.07 January 2013
9311 Macro V2 OD corrective maintenance procedures Replacing the C2OIM
Replacing the digital shelf equipment
....................................................................................................................................................................................................................................
Reconnect the two optical fibers on the C2OIM front panel.
...................................................................................................................................................................................................
10 Ask the OMC administrator to unlock all optical link objects previously locked on step 3.
...................................................................................................................................................................................................
11 Check the state of the LEDs on the C2OIM front panel. They should turn on, then take
the following state:
Result: Tx Act and Rx Act green LEDs ON
...................................................................................................................................................................................................
....................................................................................................................................................................................................................................
8-44 Alcatel-Lucent Proprietary Alcatel-Lucent 9311 Macro V2 OD
Use pursuant to applicable agreements NN-20500-011 UA08.1
Issue 09.07 January 2013
9311 Macro V2 OD corrective maintenance procedures Replacing the digital backplane of the 9311 Macro V2 OD
Replacing the digital shelf equipment
....................................................................................................................................................................................................................................
Intervention time
60 minutes
Tools required
Flat screwdriver
Cross-head screwdriver
Screwdriver for bolts (specific for 4-40 screws)
Wrench
NOTICE
ESD hazard
We recommend wearing an antistatic bracelet connected to ground via a protective
resistance to avoid damaging circuits when handling printed circuits.
Electronic boards must be stored in antistatic envelopes or inside packages both during
transportation and storage.
Important! Notify the OMC administrator in case of service outage or reduction.
Important! The tightening torque of the 4-40 UNC bolts must be 46 N.cm.
Procedure
...................................................................................................................................................................................................
2 Power down the Node B. (See Powering down a 9311 Macro V2 OD (p. 7-2))
...................................................................................................................................................................................................
...................................................................................................................................................................................................
4 Unscrew the two screws (1) per module for each digital module and filler.
...................................................................................................................................................................................................
....................................................................................................................................................................................................................................
8-46 Alcatel-Lucent Proprietary Alcatel-Lucent 9311 Macro V2 OD
Use pursuant to applicable agreements NN-20500-011 UA08.1
Issue 09.07 January 2013
9311 Macro V2 OD corrective maintenance procedures Replacing the digital backplane of the 9311 Macro V2 OD
Replacing the digital shelf equipment
....................................................................................................................................................................................................................................
...................................................................................................................................................................................................
....................................................................................................................................................................................................................................
Alcatel-Lucent 9311 Macro V2 OD Alcatel-Lucent Proprietary 8-47
NN-20500-011 UA08.1 Use pursuant to applicable agreements
Issue 09.07 January 2013
9311 Macro V2 OD corrective maintenance procedures Replacing the digital backplane of the 9311 Macro V2 OD
Replacing the digital shelf equipment
....................................................................................................................................................................................................................................
...................................................................................................................................................................................................
13 Tighten the two captive screws per digital module and filler (see legend 1 in Figure 8-22,
Digital rack front panel (p. 8-46)).
....................................................................................................................................................................................................................................
8-48 Alcatel-Lucent Proprietary Alcatel-Lucent 9311 Macro V2 OD
Use pursuant to applicable agreements NN-20500-011 UA08.1
Issue 09.07 January 2013
9311 Macro V2 OD corrective maintenance procedures Replacing the digital backplane of the 9311 Macro V2 OD
Replacing the digital shelf equipment
....................................................................................................................................................................................................................................
...................................................................................................................................................................................................
15 Reconnect the SMA connectors (2) and the UNC bolts of the Sub D connectors (5).
Note: For tightening torque, see Tools required (p. 8-45)
...................................................................................................................................................................................................
17 Check with the OMC administrator that all alarms are OK.
...................................................................................................................................................................................................
....................................................................................................................................................................................................................................
Alcatel-Lucent 9311 Macro V2 OD Alcatel-Lucent Proprietary 8-49
NN-20500-011 UA08.1 Use pursuant to applicable agreements
Issue 09.07 January 2013
9311 Macro V2 OD corrective maintenance procedures Replacing the optional xCCM radio interface Board (xCOB)
Replacing the digital shelf equipment
....................................................................................................................................................................................................................................
Tools required
To complete this procedure you will require:
Screwdriver
Extraction handle (3JR08430AA)
Local Installation Terminal (TIL)
....................................................................................................................................................................................................................................
8-50 Alcatel-Lucent Proprietary Alcatel-Lucent 9311 Macro V2 OD
Use pursuant to applicable agreements NN-20500-011 UA08.1
Issue 09.07 January 2013
9311 Macro V2 OD corrective maintenance procedures Replacing the optional xCCM radio interface Board (xCOB)
Replacing the digital shelf equipment
....................................................................................................................................................................................................................................
....................................................................................................................................................................................................................................
Alcatel-Lucent 9311 Macro V2 OD Alcatel-Lucent Proprietary 8-51
NN-20500-011 UA08.1 Use pursuant to applicable agreements
Issue 09.07 January 2013
9311 Macro V2 OD corrective maintenance procedures Replacing the optional xCCM radio interface Board (xCOB)
Replacing the digital shelf equipment
....................................................................................................................................................................................................................................
....................................................................................................................................................................................................................................
8-52 Alcatel-Lucent Proprietary Alcatel-Lucent 9311 Macro V2 OD
Use pursuant to applicable agreements NN-20500-011 UA08.1
Issue 09.07 January 2013
9311 Macro V2 OD corrective maintenance procedures Replacing the optional xCCM radio interface Board (xCOB)
Replacing the digital shelf equipment
....................................................................................................................................................................................................................................
Figure 8-26 xCOB front panel
NOTICE
Service-disruption hazard
This procedure can cause a service outage or reduction.
Notify the OMC administrator in case of service outage or reduction.
....................................................................................................................................................................................................................................
Alcatel-Lucent 9311 Macro V2 OD Alcatel-Lucent Proprietary 8-53
NN-20500-011 UA08.1 Use pursuant to applicable agreements
Issue 09.07 January 2013
9311 Macro V2 OD corrective maintenance procedures Replacing the optional xCCM radio interface Board (xCOB)
Replacing the digital shelf equipment
....................................................................................................................................................................................................................................
Procedure
Carry out the following procedure to replace XCOB module
...................................................................................................................................................................................................
2 Locate the faulty XCOB in the digital shelf: its red triangular LED is lit.
...................................................................................................................................................................................................
3 On the XCOB front panel, disconnect the six CPRI bi-directional optical or electrical
links.
...................................................................................................................................................................................................
6 Insert the new XCOB into the mini backplane of XCCM module
...................................................................................................................................................................................................
8 On the XCOB front panel, connect the six CPRI bi-directional optical or electrical links.
...................................................................................................................................................................................................
10 Check on the TIL and with the OMC administrator that the Node B is operational.
...................................................................................................................................................................................................
....................................................................................................................................................................................................................................
8-54 Alcatel-Lucent Proprietary Alcatel-Lucent 9311 Macro V2 OD
Use pursuant to applicable agreements NN-20500-011 UA08.1
Issue 09.07 January 2013
9311 Macro V2 OD corrective maintenance procedures Overview
Replacing the RF block equipment
....................................................................................................................................................................................................................................
Overview
Purpose
This section presents the replacement procedures applicable to the RF block.
Contents
....................................................................................................................................................................................................................................
Alcatel-Lucent 9311 Macro V2 OD Alcatel-Lucent Proprietary 8-55
NN-20500-011 UA08.1 Use pursuant to applicable agreements
Issue 09.07 January 2013
9311 Macro V2 OD corrective maintenance procedures Replacing the Dual Duplexer Module (DDM)
Replacing the RF block equipment
....................................................................................................................................................................................................................................
Intervention time
Ten minutes
Tools required
Extraction handle (3JR08430AA)
Flat screwdriver
SMA torque wrench
7/16 torque wrench
N torque wrench
Local Installation Terminal (TIL)
....................................................................................................................................................................................................................................
8-56 Alcatel-Lucent Proprietary Alcatel-Lucent 9311 Macro V2 OD
Use pursuant to applicable agreements NN-20500-011 UA08.1
Issue 09.07 January 2013
9311 Macro V2 OD corrective maintenance procedures Replacing the Dual Duplexer Module (DDM)
Replacing the RF block equipment
....................................................................................................................................................................................................................................
....................................................................................................................................................................................................................................
Alcatel-Lucent 9311 Macro V2 OD Alcatel-Lucent Proprietary 8-57
NN-20500-011 UA08.1 Use pursuant to applicable agreements
Issue 09.07 January 2013
9311 Macro V2 OD corrective maintenance procedures Replacing the Dual Duplexer Module (DDM)
Replacing the RF block equipment
....................................................................................................................................................................................................................................
Figure 8-28 DDM-2/DDM-E 900/DDM-P 900 front panel
....................................................................................................................................................................................................................................
8-58 Alcatel-Lucent Proprietary Alcatel-Lucent 9311 Macro V2 OD
Use pursuant to applicable agreements NN-20500-011 UA08.1
Issue 09.07 January 2013
9311 Macro V2 OD corrective maintenance procedures Replacing the Dual Duplexer Module (DDM)
Replacing the RF block equipment
....................................................................................................................................................................................................................................
Important!
The tightening torque of the front panel screws must be 0.25 N.m (0.2375 N.m to
0.2625 N.m).
The SMA tightening torque must be 0.8 N.m to 1.2 N.m.
The 7/16 tightening torque must be 25 N.m (24 N.m to 27 N.m).
The N tightening torque must be 1.7 N.m (1.6 N.m to 1.8 N.m).
CAUTION
RF hazard
RF exposure in excess of applicable limits can result in serious personal injury.
Observe the following:
Turn off and lockout the transmit power before working on the antenna system.
If the transmitters must be tested with the antennas connected, adhere to appropriate
antenna stand-off distances.
Do not use auxiliary antennas.
Consult with the Antenna exposure statements before begining work.
NOTICE
ESD hazard
We recommend wearing an antistatic bracelet connected to ground via a protective
resistance to avoid damaging circuits when handling printed circuits.
Electronic boards must be stored in antistatic envelopes or inside packages both during
transportation and storage.
Important! This procedure requires a service reduction from the Node B estimated at
ten minutes. Notify the OMC administrator.
Procedure
...................................................................................................................................................................................................
2 Locate the faulty DDM in the DDM shelf: its red triangular LED is lit.
...................................................................................................................................................................................................
3 Ask the OMC administrator to lock the ddm object (by Set Administrative State). It is
also recommended to lock the mcpa object of the associated MCPA/SCPA module. For
more information, refer to Alcatel-Lucent 9353 Wireless Management System - User
Guide, NN-20500-032.
....................................................................................................................................................................................................................................
Alcatel-Lucent 9311 Macro V2 OD Alcatel-Lucent Proprietary 8-59
NN-20500-011 UA08.1 Use pursuant to applicable agreements
Issue 09.07 January 2013
9311 Macro V2 OD corrective maintenance procedures Replacing the Dual Duplexer Module (DDM)
Replacing the RF block equipment
....................................................................................................................................................................................................................................
...................................................................................................................................................................................................
5 Disconnect the following cables and connectors from the DDM front panel:
The power cable (connection with the Interco module)
For AISG DDM, the AISG cable (connection with CCU)
The two antenna cables using the 7/16 wrench (connection with RF bulkheads)
The Rx cables using the SMA wrench (connection with the TRM/iTRM module)
The transmitter cable using the N wrench (connection with the MCPA/SCPA module)
...................................................................................................................................................................................................
7 Extract the defective DDM with the extraction handle and remove it.
...................................................................................................................................................................................................
9 Remove the 50-ohm loads from the Rx ports that are to be plugged.
These 50-ohm loads are present on the Rx ports labelled Rx1, Rx2, Rx3 on the DDM
front panel.
...................................................................................................................................................................................................
....................................................................................................................................................................................................................................
8-60 Alcatel-Lucent Proprietary Alcatel-Lucent 9311 Macro V2 OD
Use pursuant to applicable agreements NN-20500-011 UA08.1
Issue 09.07 January 2013
9311 Macro V2 OD corrective maintenance procedures Replacing the Dual Duplexer Module (DDM)
Replacing the RF block equipment
....................................................................................................................................................................................................................................
...................................................................................................................................................................................................
13 Reconnect the following cables and connectors to the DDM front panel:
The two antenna cables using the 7/16 wrench
The Rx cables using the SMA wrench
The transmitter cable using the N wrench
The AISG cable for AISG DDM
Important! Pay attention to cable torsion and bend radius for the two antenna cables
(between DDM and Bulkhead).
The following figure gives the bad example for the assembly of antenna cables. The curve
may damage the cable
....................................................................................................................................................................................................................................
Alcatel-Lucent 9311 Macro V2 OD Alcatel-Lucent Proprietary 8-61
NN-20500-011 UA08.1 Use pursuant to applicable agreements
Issue 09.07 January 2013
9311 Macro V2 OD corrective maintenance procedures Replacing the Dual Duplexer Module (DDM)
Replacing the RF block equipment
....................................................................................................................................................................................................................................
The following figure gives a correct example for the assembly of antenna cables
Note: For tightening torques, see Caution table in Tools required (p. 8-56) section.
...................................................................................................................................................................................................
14 Reset the Node B by using the TIL tool or from the OMC. For more information, refer to
the following documents:
Alcatel-Lucent 9100 and 93xx Node B - Commissioning and Fault Management User
Manual: TIL, NN-20500-019
Alcatel-Lucent 9353 Wireless Management System - User Guide, NN-20500-032
...................................................................................................................................................................................................
15 Ask the OMC administrator to unlock the ddm and mcpa objects previously locked on
step 3. For more information, refer to Alcatel-Lucent 9353 Wireless Management System -
User Guide, NN-20500-032.
...................................................................................................................................................................................................
16 Check the state of the DDM LEDs. They should go on then take the following states:
Result: Red triangular LED OFF, green rectangular LED ON
...................................................................................................................................................................................................
18 Check on the TIL and with the OMC administrator that the Node B is operational.
....................................................................................................................................................................................................................................
8-62 Alcatel-Lucent Proprietary Alcatel-Lucent 9311 Macro V2 OD
Use pursuant to applicable agreements NN-20500-011 UA08.1
Issue 09.07 January 2013
9311 Macro V2 OD corrective maintenance procedures Replacing the Dual Duplexer Module (DDM)
Replacing the RF block equipment
....................................................................................................................................................................................................................................
...................................................................................................................................................................................................
....................................................................................................................................................................................................................................
Alcatel-Lucent 9311 Macro V2 OD Alcatel-Lucent Proprietary 8-63
NN-20500-011 UA08.1 Use pursuant to applicable agreements
Issue 09.07 January 2013
9311 Macro V2 OD corrective maintenance procedures Replacing the Multi-Carrier Power Amplifier module (MCPA)
Replacing the RF block equipment or Single-Carrier Power Amplifier module (SCPA)
....................................................................................................................................................................................................................................
Intervention time
15 minutes
Tools required
SMA torque wrench
N torque wrench
Phillips and flat screwdrivers
....................................................................................................................................................................................................................................
8-64 Alcatel-Lucent Proprietary Alcatel-Lucent 9311 Macro V2 OD
Use pursuant to applicable agreements NN-20500-011 UA08.1
Issue 09.07 January 2013
9311 Macro V2 OD corrective maintenance procedures Replacing the Multi-Carrier Power Amplifier module (MCPA)
Replacing the RF block equipment or Single-Carrier Power Amplifier module (SCPA)
....................................................................................................................................................................................................................................
....................................................................................................................................................................................................................................
Alcatel-Lucent 9311 Macro V2 OD Alcatel-Lucent Proprietary 8-65
NN-20500-011 UA08.1 Use pursuant to applicable agreements
Issue 09.07 January 2013
9311 Macro V2 OD corrective maintenance procedures Replacing the Multi-Carrier Power Amplifier module (MCPA)
Replacing the RF block equipment or Single-Carrier Power Amplifier module (SCPA)
....................................................................................................................................................................................................................................
Figure 8-33 MCPA 60W-A front panel
....................................................................................................................................................................................................................................
8-66 Alcatel-Lucent Proprietary Alcatel-Lucent 9311 Macro V2 OD
Use pursuant to applicable agreements NN-20500-011 UA08.1
Issue 09.07 January 2013
9311 Macro V2 OD corrective maintenance procedures Replacing the Multi-Carrier Power Amplifier module (MCPA)
Replacing the RF block equipment or Single-Carrier Power Amplifier module (SCPA)
....................................................................................................................................................................................................................................
Figure 8-34 MCPA 60W-B front panel
Unlike the MCPA 60W-B module, the MCPA 60W-A module is not equipped with two
RF connectors for feedback links to xTRM (see FB1 and FB2 in Figure 8-34, MCPA
60W-B front panel (p. 8-67)).
For differences between MCPA 60W-A and MCPA 60W-B, refer to Alcatel-Lucent 9311
Macro V2 Node B Outdoor Technical Description, NN-20500-004.
....................................................................................................................................................................................................................................
Alcatel-Lucent 9311 Macro V2 OD Alcatel-Lucent Proprietary 8-67
NN-20500-011 UA08.1 Use pursuant to applicable agreements
Issue 09.07 January 2013
9311 Macro V2 OD corrective maintenance procedures Replacing the Multi-Carrier Power Amplifier module (MCPA)
Replacing the RF block equipment or Single-Carrier Power Amplifier module (SCPA)
....................................................................................................................................................................................................................................
CAUTION
RF hazard
RF exposure in excess of applicable limits can result in serious personal injury.
Observe the following:
Turn off and lockout the transmit power before working on the antenna system.
If the transmitters must be tested with the antennas connected, adhere to appropriate
antenna stand-off distances.
Do not use auxiliary antennas.
Consult with the Antenna exposure statements before begining work.
....................................................................................................................................................................................................................................
8-68 Alcatel-Lucent Proprietary Alcatel-Lucent 9311 Macro V2 OD
Use pursuant to applicable agreements NN-20500-011 UA08.1
Issue 09.07 January 2013
9311 Macro V2 OD corrective maintenance procedures Replacing the Multi-Carrier Power Amplifier module (MCPA)
Replacing the RF block equipment or Single-Carrier Power Amplifier module (SCPA)
....................................................................................................................................................................................................................................
NOTICE
ESD hazard
We recommend wearing an antistatic bracelet connected to ground via a protective
resistance to avoid damaging circuits when handling printed circuits.
Electronic boards must be stored in antistatic envelopes or inside packages both during
transportation and storage.
NOTICE
Service-disruption hazard
This procedure will result in service disruption. Notify the OMC administrator of a
service outage before commencing.
Important!
The tightening torque of the front panel screws must be 0.25 N.m (0.2375 N.m to
0.2625 N.m).
The SMA tightening torque must be 0.8 N.m to 1.2 N.m.
The N tightening torque must be 1.7 N.m (1.6 N.m to 1.8 N.m).
Procedure
...................................................................................................................................................................................................
6 Important! Beware that if you do not disconnect the power cable at the
interconnection module, there is a risk of destroying the equipment, because of a
connected -48 V cable hanging down.
First, remove the power cable at the interconnection module (do not remove the data
cable). Then, in front of the faulty MCPA/SCPA module, disconnect the power cable that
is connected to the "Power IN" connector.
...................................................................................................................................................................................................
7 Untighten the four MCPA/SCPA module front panel screws (2) using the Phillips
screwdriver.
...................................................................................................................................................................................................
8 Remove the faulty MCPA/SCPA module using the front panel handle (1).
...................................................................................................................................................................................................
10 Tighten the four MCPA/SCPA module front panel screws, using the Phillips screwdriver.
...................................................................................................................................................................................................
12 Important! Before connecting the power cable to the MCPA/SCPA module connector
:
Check the correct side of the D-sub connector.
Make sure the small side of the MCPA/SCPA module connector is connected to
the small side of the MCPA/SCPA module cable connector.
Never connect the small side with the large side, otherwise there is a risk of
MCPA/SCPA module failure.
Notice that the MCPA/SCPA modules stand upside down in the 9311 Macro V2 OD
cabinet.
In front of the MCPA/SCPA module, connect the power cable to the "Power IN"
connector.
....................................................................................................................................................................................................................................
8-70 Alcatel-Lucent Proprietary Alcatel-Lucent 9311 Macro V2 OD
Use pursuant to applicable agreements NN-20500-011 UA08.1
Issue 09.07 January 2013
9311 Macro V2 OD corrective maintenance procedures Replacing the Multi-Carrier Power Amplifier module (MCPA)
Replacing the RF block equipment or Single-Carrier Power Amplifier module (SCPA)
....................................................................................................................................................................................................................................
...................................................................................................................................................................................................
13 DANGER
Personnel protection
When connecting the power cable to the interconnection module, be careful not to touch
the interconnection module.
Connect the power cable to the interconnection module.
...................................................................................................................................................................................................
17 <Optional> If the MCPA/SCPA module is not automatically unlocked, ask the OMC
administrator to unlock the mcpa object previously locked on step 3. For more
information, refer to Alcatel-Lucent 9353 Wireless Management System - User Guide,
NN-20500-032.
....................................................................................................................................................................................................................................
Alcatel-Lucent 9311 Macro V2 OD Alcatel-Lucent Proprietary 8-71
NN-20500-011 UA08.1 Use pursuant to applicable agreements
Issue 09.07 January 2013
9311 Macro V2 OD corrective maintenance procedures Replacing the Multi-Carrier Power Amplifier module (MCPA)
Replacing the RF block equipment or Single-Carrier Power Amplifier module (SCPA)
....................................................................................................................................................................................................................................
...................................................................................................................................................................................................
18 Check the MCPA/SCPA LED if the Node B is connected and configured by the network:
The MCPA/SCPA LED is Green if it is configured to transmit
The MCPA/SCPA LED is Red as long as it is not configured to transmit
...................................................................................................................................................................................................
....................................................................................................................................................................................................................................
8-72 Alcatel-Lucent Proprietary Alcatel-Lucent 9311 Macro V2 OD
Use pursuant to applicable agreements NN-20500-011 UA08.1
Issue 09.07 January 2013
9311 Macro V2 OD corrective maintenance procedures Replacing the Multi-Carrier Power Amplifier module (MCPA)
Replacing the RF block equipment or Single-Carrier Power Amplifier module (SCPA)
....................................................................................................................................................................................................................................
Downloading error at the OMC-B
After an MCPA replacement, the firmware of the replacing MCPA is upgraded for the
mentioned MCPA types. Most of the time, this firmware download is successful, and
allows to upgrade the Cajun MCPA module that has just been inserted without resetting
the Node B. But in some rare cases, the download attempt may result in a Downloading
Error and a minor alarm reporting to the OMC-B, with the following status:
Cause: Downloading Error
Equipment Type: MCPA
Perceived Severity: minor
This alarm is minor since the MCPA continues to be operational in its not upgraded
version. The Downloading Error cause has four sub-causes, that are described in the
following table.
....................................................................................................................................................................................................................................
Alcatel-Lucent 9311 Macro V2 OD Alcatel-Lucent Proprietary 8-73
NN-20500-011 UA08.1 Use pursuant to applicable agreements
Issue 09.07 January 2013
9311 Macro V2 OD corrective maintenance procedures Replacing the Multi-Carrier Power Amplifier module (MCPA)
Replacing the RF block equipment or Single-Carrier Power Amplifier module (SCPA)
....................................................................................................................................................................................................................................
Table 8-1 Downloading error sub-causes (continued)
The following flow diagram illustrates the global Cajun MCPA download process,
including the maintenance actions to be performed in case of a Downloading Error
alarm.
....................................................................................................................................................................................................................................
8-74 Alcatel-Lucent Proprietary Alcatel-Lucent 9311 Macro V2 OD
Use pursuant to applicable agreements NN-20500-011 UA08.1
Issue 09.07 January 2013
9311 Macro V2 OD corrective maintenance procedures Replacing the Multi-Carrier Power Amplifier module (MCPA)
Replacing the RF block equipment or Single-Carrier Power Amplifier module (SCPA)
....................................................................................................................................................................................................................................
....................................................................................................................................................................................................................................
Alcatel-Lucent 9311 Macro V2 OD Alcatel-Lucent Proprietary 8-75
NN-20500-011 UA08.1 Use pursuant to applicable agreements
Issue 09.07 January 2013
9311 Macro V2 OD corrective maintenance procedures Replacing the Tx Splitter
Replacing the RF block equipment
....................................................................................................................................................................................................................................
Intervention time
Ten minutes
Tools required
N torque wrench
Phillips screwdriver
Flat screwdriver
Local Installation Terminal (TIL)
....................................................................................................................................................................................................................................
8-76 Alcatel-Lucent Proprietary Alcatel-Lucent 9311 Macro V2 OD
Use pursuant to applicable agreements NN-20500-011 UA08.1
Issue 09.07 January 2013
9311 Macro V2 OD corrective maintenance procedures Replacing the Tx Splitter
Replacing the RF block equipment
....................................................................................................................................................................................................................................
CAUTION
RF hazard
RF exposure in excess of applicable limits can result in serious personal injury.
Observe the following:
Turn off and lockout the transmit power before working on the antenna system.
If the transmitters must be tested with the antennas connected, adhere to appropriate
antenna stand-off distances.
Do not use auxiliary antennas.
Consult with the Antenna exposure statements before begining work.
NOTICE
ESD hazard
Electronic components can be destroyed by electrostatic discharge (ESD). Hold circuit
packs only at the edges or on the insertion and removal facilities. Always observe the
general ESD instructions.
Important!
The N tightening torque must be 1.7 N.m (1.6 N.m to 1.8 N.m).
The tightening torque of the front panel screws must be 0.25 N.m (0.2375 N.m to
0.2625 N.m).
Important! This procedure leads to a service outage from the Node B estimated at ten
minutes. Notify the OMC administrator of a service outage.
Important! Respect bend radius of cables while tightening connectors.
Pay attention to cable torsion and bend radius during maintenance operations.
Procedure
...................................................................................................................................................................................................
2 Locate the faulty Tx Splitter in the MCPA shelf, its LED is OFF (1).
...................................................................................................................................................................................................
5 Disconnect the following cables and connectors from the front panel of the Tx Splitter:
The three DDM cables (N connectors) using the N torque wrench
The MCPA module cable (N connector) using the N torque wrench
...................................................................................................................................................................................................
6 Undo the four securing screws on the front panel of the Tx Splitter (2).
...................................................................................................................................................................................................
7 Extract the faulty Tx Splitter with the handle and remove it.
...................................................................................................................................................................................................
10 Reconnect the following cables and connectors to the front panel of the Tx Splitter:
the MCPA module cable using the N torque wrench
the three DDM cables using the N torque wrench
Note: For tightening torques, see Caution table in Tools required (p. 8-76).
...................................................................................................................................................................................................
12 Reset the Node B by using the TIL tool or from the OMC. For more information, refer to
the following documents:
Alcatel-Lucent 9100 and 93xx Node B - Commissioning and Fault Management User
Manual: TIL, NN-20500-019
Alcatel-Lucent 9353 Management System - User Guide, NN-20500-032
...................................................................................................................................................................................................
13 Ask the OMC administrator to unlock the DDM and MCPA objects previously locked on
step 3. For more information, refer to Alcatel-Lucent 9353 Management System - User
Guide, NN-20500-032.
...................................................................................................................................................................................................
....................................................................................................................................................................................................................................
8-78 Alcatel-Lucent Proprietary Alcatel-Lucent 9311 Macro V2 OD
Use pursuant to applicable agreements NN-20500-011 UA08.1
Issue 09.07 January 2013
9311 Macro V2 OD corrective maintenance procedures Replacing the Tx Splitter
Replacing the RF block equipment
....................................................................................................................................................................................................................................
Result: Green LED ON
...................................................................................................................................................................................................
15 Check on the TIL and with the OMC administrator that the Node B is operational.
...................................................................................................................................................................................................
....................................................................................................................................................................................................................................
Alcatel-Lucent 9311 Macro V2 OD Alcatel-Lucent Proprietary 8-79
NN-20500-011 UA08.1 Use pursuant to applicable agreements
Issue 09.07 January 2013
9311 Macro V2 OD corrective maintenance procedures Replacing a TRDU
Replacing the RF block equipment
....................................................................................................................................................................................................................................
Replacing a TRDU
Carry out the following procedure to replace a TRDU.
Important! Mixity restriction : TRDU model mixity is not allowed within a cluster.
Note: Make sure that the TRDU module type used as a spare part is identical to the
one to be replaced in the MCDA shelf (TRDU60-21, TRDU60-21B). The left and
right parts of the shelf must consist of three modules of the same type per sector (for
example, S1: TRDU60-21, S2: TRDU60-21B).
Note: To exchange a faulty TRDU module, replace it with a module of the same type
in a group of three identical modules.
Intervention time
15 minutes
Tools required
7/16 torque wrench
Phillips screwdriver
Extraction tool (3JR08430AA)
....................................................................................................................................................................................................................................
8-80 Alcatel-Lucent Proprietary Alcatel-Lucent 9311 Macro V2 OD
Use pursuant to applicable agreements NN-20500-011 UA08.1
Issue 09.07 January 2013
9311 Macro V2 OD corrective maintenance procedures Replacing a TRDU
Replacing the RF block equipment
....................................................................................................................................................................................................................................
....................................................................................................................................................................................................................................
Alcatel-Lucent 9311 Macro V2 OD Alcatel-Lucent Proprietary 8-81
NN-20500-011 UA08.1 Use pursuant to applicable agreements
Issue 09.07 January 2013
9311 Macro V2 OD corrective maintenance procedures Replacing a TRDU
Replacing the RF block equipment
....................................................................................................................................................................................................................................
Figure 8-39 TRDU60-21B front panel
CAUTION
Burn hazard
Module becomes very hot during operation.
Wear gloves when removing the module.
....................................................................................................................................................................................................................................
8-82 Alcatel-Lucent Proprietary Alcatel-Lucent 9311 Macro V2 OD
Use pursuant to applicable agreements NN-20500-011 UA08.1
Issue 09.07 January 2013
9311 Macro V2 OD corrective maintenance procedures Replacing a TRDU
Replacing the RF block equipment
....................................................................................................................................................................................................................................
NOTICE
ESD hazard
Electronic components can be destroyed by electrostatic discharge (ESD).
Hold circuit packs only at the edges or on the insertion and removal facilities.
Always observe the general ESD instructions.
NOTICE
Service-disruption hazard
Following the procedure below will result in a loss of service.
Important! Service is lost on the radio links associated with the TRDU being
replaced.
Important! The 7/16 tightening torque must be 25 N.m (24 N.m to 27 N.m).
Important! Respect bend radius of cables while tightening connectors.
Pay attention to cable torsion and bend radius during maintenance operations.
Procedure
...................................................................................................................................................................................................
1 Locate the faulty TRDU in the TRDU sub-rack: its red LED is on.
...................................................................................................................................................................................................
2 At the OMC, lock the faulty TRDU by Set Administrative State. For more information,
refer to Alcatel-Lucent 9353 Wireless Management System - User Guide, NN-20500-032.
...................................................................................................................................................................................................
3 Switch off the faulty TRDU (on the TRDU front panel, put the power switch in the "O"
position).
....................................................................................................................................................................................................................................
Alcatel-Lucent 9311 Macro V2 OD Alcatel-Lucent Proprietary 8-83
NN-20500-011 UA08.1 Use pursuant to applicable agreements
Issue 09.07 January 2013
9311 Macro V2 OD corrective maintenance procedures Replacing a TRDU
Replacing the RF block equipment
....................................................................................................................................................................................................................................
...................................................................................................................................................................................................
4 On the front panel of the faulty TRDU, disconnect the following cables:
The two RF antenna cables (connectors labeled "RX" and "TX/RX"), using the 7/16
wrench
The CPRI cable (connector labeled "DATA I/O SLAVE")
The AISG input digital cable (9-pin D-SUB connector labeled "AISG IN"), if CCU
for RETA is used
...................................................................................................................................................................................................
5 Important! Beware that if you do not disconnect the power cable at the
interconnection module, there is a risk of destroying the equipment, because of a
connected -48 V cable hanging down.
First, remove the power cable at the interconnection module (do not remove the data
cable). Then, in front of the faulty TRDU module, disconnect the power cable that is
connected to the "Power IN" connector.
....................................................................................................................................................................................................................................
8-84 Alcatel-Lucent Proprietary Alcatel-Lucent 9311 Macro V2 OD
Use pursuant to applicable agreements NN-20500-011 UA08.1
Issue 09.07 January 2013
9311 Macro V2 OD corrective maintenance procedures Replacing a TRDU
Replacing the RF block equipment
....................................................................................................................................................................................................................................
...................................................................................................................................................................................................
6 Untighten the four TRDU front panel screws using the Phillips screwdriver.
...................................................................................................................................................................................................
9 Tighten the four screws on the new TRDU front panel using the Phillips screwdriver.
...................................................................................................................................................................................................
10 Check that the power switch on the new TRDU is in the "O" position.
...................................................................................................................................................................................................
11 On the new TRDU front panel, connect the power cable to the "POWER IN" connector.
...................................................................................................................................................................................................
12 DANGER
Personnel protection
When connecting the power cable to the interconnection module, be careful not to touch
the interconnection module.
Connect the power cable to the interconnection module.
...................................................................................................................................................................................................
14 Switch on the new TRDU (on the TRDU front panel, put the power switch in the "I"
position).
The TRDU is automatically unlocked.
During TRDU startup, the green and red LEDs on TRDU front panel are on.
Wait for TRDU startup.
....................................................................................................................................................................................................................................
Alcatel-Lucent 9311 Macro V2 OD Alcatel-Lucent Proprietary 8-85
NN-20500-011 UA08.1 Use pursuant to applicable agreements
Issue 09.07 January 2013
9311 Macro V2 OD corrective maintenance procedures Replacing a TRDU
Replacing the RF block equipment
....................................................................................................................................................................................................................................
...................................................................................................................................................................................................
15 If the TRDU is not automatically unlocked, unlock the TRDU at the OMC by Set
Administrative State. For more information, refer to Alcatel-Lucent 9353 Wireless
Management System - User Guide, NN-20500-032.
...................................................................................................................................................................................................
16 On the xCCM front panel, for the CPRI port concerned, check that the Tx and Rx LEDs
are green (the communication is established between the 9311 Macro V2 OD and the new
TRDU).
...................................................................................................................................................................................................
E...................................................................................................................................................................................................
N D O F S T E P S
....................................................................................................................................................................................................................................
8-86 Alcatel-Lucent Proprietary Alcatel-Lucent 9311 Macro V2 OD
Use pursuant to applicable agreements NN-20500-011 UA08.1
Issue 09.07 January 2013
9311 Macro V2 OD corrective maintenance procedures Overview
Replacing the cooling system equipment
....................................................................................................................................................................................................................................
Overview
Purpose
This section presents the replacement procedures applicable to the cooling system of the
9311 Macro OD cabinets.
Contents
....................................................................................................................................................................................................................................
Alcatel-Lucent 9311 Macro V2 OD Alcatel-Lucent Proprietary 8-87
NN-20500-011 UA08.1 Use pursuant to applicable agreements
Issue 09.07 January 2013
9311 Macro V2 OD corrective maintenance procedures Replacing the air filter
Replacing the cooling system equipment
....................................................................................................................................................................................................................................
Intervention time
Five minutes
Tools required
Phillips screwdriver
WARNING
Electric-shock hazard
Some parts of all electrical installations are energized. Failure to follow safe work
practices and the safety warnings may lead to bodily injury and property damage. For
this reason, only trained and qualified personnel (electrical workers as defined in IEC
60215 or EN 60215 + A1 or in the National Electrical Code or in ANSI/NFPA No.10)
may install or service the installation.
NOTICE
ESD hazard
Electronic components can be destroyed by electrostatic discharge (ESD). Hold circuit
packs only at the edges or on the insertion and removal facilities. Always observe the
general ESD instructions.
Procedure
...................................................................................................................................................................................................
3 Unscrew the captive screw (4) holding the door jam (2).
....................................................................................................................................................................................................................................
8-88 Alcatel-Lucent Proprietary Alcatel-Lucent 9311 Macro V2 OD
Use pursuant to applicable agreements NN-20500-011 UA08.1
Issue 09.07 January 2013
9311 Macro V2 OD corrective maintenance procedures Replacing the air filter
Replacing the cooling system equipment
....................................................................................................................................................................................................................................
...................................................................................................................................................................................................
...................................................................................................................................................................................................
....................................................................................................................................................................................................................................
Alcatel-Lucent 9311 Macro V2 OD Alcatel-Lucent Proprietary 8-89
NN-20500-011 UA08.1 Use pursuant to applicable agreements
Issue 09.07 January 2013
9311 Macro V2 OD corrective maintenance procedures Replacing the air filter
Replacing the cooling system equipment
....................................................................................................................................................................................................................................
...................................................................................................................................................................................................
....................................................................................................................................................................................................................................
8-90 Alcatel-Lucent Proprietary Alcatel-Lucent 9311 Macro V2 OD
Use pursuant to applicable agreements NN-20500-011 UA08.1
Issue 09.07 January 2013
9311 Macro V2 OD corrective maintenance procedures Replacing the ECU control board
Replacing the cooling system equipment
....................................................................................................................................................................................................................................
Intervention time
30 minutes
Tools required
Phillips screwdriver
Flat screwdriver
WARNING
Electric-shock hazard
Some parts of all electrical installations are energized. Failure to follow safe work
practices and the safety warnings may lead to bodily injury and property damage. For
this reason, only trained and qualified personnel (electrical workers as defined in IEC
60215 or EN 60215 + A1 or in the National Electrical Code or in ANSI/NFPA No.10)
may install or service the installation.
NOTICE
ESD hazard
Electronic components can be destroyed by electrostatic discharge (ESD). Hold circuit
packs only at the edges or on the insertion and removal facilities. Always observe the
general ESD instructions.
Procedure
...................................................................................................................................................................................................
3 Switch OFF the CB02 and CB03 circuit breakers on the ADU module.
...................................................................................................................................................................................................
5 Disconnect the two cables (NTT995 PA iss02 cable and DALLAS cable) connected to the
control box.
...................................................................................................................................................................................................
8 Disconnect the nine cables (P1, P2, P3, P9, P10, P11, P12A, P12B, and P13) connected to
the control board.
The following figure indicates the connectors to which cables are connected to the control
board.
....................................................................................................................................................................................................................................
8-92 Alcatel-Lucent Proprietary Alcatel-Lucent 9311 Macro V2 OD
Use pursuant to applicable agreements NN-20500-011 UA08.1
Issue 09.07 January 2013
9311 Macro V2 OD corrective maintenance procedures Replacing the ECU control board
Replacing the cooling system equipment
....................................................................................................................................................................................................................................
...................................................................................................................................................................................................
....................................................................................................................................................................................................................................
Alcatel-Lucent 9311 Macro V2 OD Alcatel-Lucent Proprietary 8-93
NN-20500-011 UA08.1 Use pursuant to applicable agreements
Issue 09.07 January 2013
9311 Macro V2 OD corrective maintenance procedures Replacing the ECU control board
Replacing the cooling system equipment
....................................................................................................................................................................................................................................
...................................................................................................................................................................................................
13 Connect the nine cables (P1, P2, P3, P9, P10, P11, P12A, P12B, and P13) to the control
board.
...................................................................................................................................................................................................
16 Connect the NTT995 PA iss02 cable and DALLAS cable to the control box.
...................................................................................................................................................................................................
19 Switch ON the CB02 and CB03 circuit breakers on the ADU module.
...................................................................................................................................................................................................
....................................................................................................................................................................................................................................
8-94 Alcatel-Lucent Proprietary Alcatel-Lucent 9311 Macro V2 OD
Use pursuant to applicable agreements NN-20500-011 UA08.1
Issue 09.07 January 2013
9311 Macro V2 OD corrective maintenance procedures Replacing a fan
Replacing the cooling system equipment
....................................................................................................................................................................................................................................
Replacing a fan
Purpose
Perform the following procedure to replace a fan of the 9311 Macro V2 OD.
Intervention time
15 minutes
Tools required
Phillips screwdriver
8-mm wrench
NOTICE
ESD hazard
Electronic components can be destroyed by electrostatic discharge (ESD). Hold circuit
packs only at the edges or on the insertion and removal facilities. Always observe the
general ESD instructions.
NOTICE
Temperature range
Do not replace a fan when the temperature exceeds the equipment temperature range.
Procedure
...................................................................................................................................................................................................
2 Switch OFF the ECU, the ADU circuit breaker CB01, and the DDU.
...................................................................................................................................................................................................
4 Disconnect the cable with orange connector from the ECU control box (on the right side
of the upper compartment).
...................................................................................................................................................................................................
....................................................................................................................................................................................................................................
Alcatel-Lucent 9311 Macro V2 OD Alcatel-Lucent Proprietary 8-95
NN-20500-011 UA08.1 Use pursuant to applicable agreements
Issue 09.07 January 2013
9311 Macro V2 OD corrective maintenance procedures Replacing a fan
Replacing the cooling system equipment
....................................................................................................................................................................................................................................
...................................................................................................................................................................................................
7 Unscrew the captive screw (M5 F5-99-143) holding the door jam.
...................................................................................................................................................................................................
9 Turn the two 1/4 turn studs (1), on the left and right sides of the ECU moving part.
...................................................................................................................................................................................................
....................................................................................................................................................................................................................................
8-96 Alcatel-Lucent Proprietary Alcatel-Lucent 9311 Macro V2 OD
Use pursuant to applicable agreements NN-20500-011 UA08.1
Issue 09.07 January 2013
9311 Macro V2 OD corrective maintenance procedures Replacing a fan
Replacing the cooling system equipment
....................................................................................................................................................................................................................................
...................................................................................................................................................................................................
15 Unscrew the four "H-eco-fix" screws (3) holding the fan to its support.
...................................................................................................................................................................................................
17 Tighten the four "H-eco-fix" screws holding the fan to its support.
...................................................................................................................................................................................................
30 Switch ON the ECU, the ADU circuit breaker CB01, and the DDU.
...................................................................................................................................................................................................
....................................................................................................................................................................................................................................
8-98 Alcatel-Lucent Proprietary Alcatel-Lucent 9311 Macro V2 OD
Use pursuant to applicable agreements NN-20500-011 UA08.1
Issue 09.07 January 2013
9311 Macro V2 OD corrective maintenance procedures Replacing the ECU ASSY S180
Replacing the cooling system equipment
....................................................................................................................................................................................................................................
Intervention time
30 minutes
Tools required
Phillips screwdriver
Cutter-pliers
Ty-raps
WARNING
Electric-shock hazard
Some parts of all electrical installations are energized. Failure to follow safe work
practices and the safety warnings may lead to bodily injury and property damage. For
this reason, only trained and qualified personnel (electrical workers as defined in IEC
60215 or EN 60215 + A1 or in the National Electrical Code or in ANSI/NFPA No.10)
may install or service the installation.
NOTICE
ESD hazard
Electronic components can be destroyed by electrostatic discharge (ESD). Hold circuit
packs only at the edges or on the insertion and removal facilities. Always observe the
general ESD instructions.
Procedure
...................................................................................................................................................................................................
....................................................................................................................................................................................................................................
Alcatel-Lucent 9311 Macro V2 OD Alcatel-Lucent Proprietary 8-99
NN-20500-011 UA08.1 Use pursuant to applicable agreements
Issue 09.07 January 2013
9311 Macro V2 OD corrective maintenance procedures Replacing the ECU ASSY S180
Replacing the cooling system equipment
....................................................................................................................................................................................................................................
...................................................................................................................................................................................................
5 Disconnect the cable with the orange connector from the ECU control box (on the right
side of the ECU).
...................................................................................................................................................................................................
8 Remove the captive screw (4) holding the door jam (2) in front of the ECU.
...................................................................................................................................................................................................
11 Turn the two 1/4 turn studs on the left (5) and right (3) sides of the ECU moving part
(ECU ASSY S180).
...................................................................................................................................................................................................
14 Tighten the two 1/4 turn studs holding the ECU moving part.
...................................................................................................................................................................................................
20 Reconnect the cable with the orange connector to the control box.
...................................................................................................................................................................................................
....................................................................................................................................................................................................................................
Alcatel-Lucent 9311 Macro V2 OD Alcatel-Lucent Proprietary 8-101
NN-20500-011 UA08.1 Use pursuant to applicable agreements
Issue 09.07 January 2013
9311 Macro V2 OD corrective maintenance procedures Overview
....................................................................................................................................................................................................................................
Overview
Purpose
This section presents the replacement procedures applicable to the power system of the
9311 Macro OD cabinets.
Contents
....................................................................................................................................................................................................................................
8-102 Alcatel-Lucent Proprietary Alcatel-Lucent 9311 Macro V2 OD
Use pursuant to applicable agreements NN-20500-011 UA08.1
Issue 09.07 January 2013
9311 Macro V2 OD corrective maintenance procedures Replacing the ADU module
Replacing the power system equipment
....................................................................................................................................................................................................................................
Intervention time
20 minutes
Tools required
Flat screwdriver
Phillips screwdriver
10-mm wrench
WARNING
Electric-shock hazard
Some parts of all electrical installations are energized. Failure to follow safe work
practices and the safety warnings may lead to bodily injury and property damage. For
this reason, only trained and qualified personnel (electrical workers as defined in IEC
60215 or EN 60215 + A1 or in the National Electrical Code or in ANSI/NFPA No.10)
may install or service the installation.
NOTICE
ESD hazard
Electronic components can be destroyed by electrostatic discharge (ESD). Hold circuit
packs only at the edges or on the insertion and removal facilities. Always observe the
general ESD instructions.
Important! During the replacement, the service is lost if the ac box breaks down.
Notify the OMC administrator in case of service interruption.
Important! Before visiting the site, check that there has been no mains power failure
on the site within the last 24 hours. After a mains power failure, the cabinet must
operate on the mains for at least 12 hours to recharge the battery.
....................................................................................................................................................................................................................................
Alcatel-Lucent 9311 Macro V2 OD Alcatel-Lucent Proprietary 8-103
NN-20500-011 UA08.1 Use pursuant to applicable agreements
Issue 09.07 January 2013
9311 Macro V2 OD corrective maintenance procedures Replacing the ADU module
Replacing the power system equipment
....................................................................................................................................................................................................................................
Procedure
...................................................................................................................................................................................................
3 Disconnect the following cables connected to the ADU, as well as the ground cable:
"ABM/TB - UIA/ADU/MCA/BC" (1)
"ADU - ECU" (3)
"TB - ADU" (4)
"ADU - UCPS" (2)
Ground cable (5)
....................................................................................................................................................................................................................................
8-104 Alcatel-Lucent Proprietary Alcatel-Lucent 9311 Macro V2 OD
Use pursuant to applicable agreements NN-20500-011 UA08.1
Issue 09.07 January 2013
9311 Macro V2 OD corrective maintenance procedures Replacing the ADU module
Replacing the power system equipment
....................................................................................................................................................................................................................................
...................................................................................................................................................................................................
....................................................................................................................................................................................................................................
Alcatel-Lucent 9311 Macro V2 OD Alcatel-Lucent Proprietary 8-105
NN-20500-011 UA08.1 Use pursuant to applicable agreements
Issue 09.07 January 2013
9311 Macro V2 OD corrective maintenance procedures Replacing the ADU module
Replacing the power system equipment
....................................................................................................................................................................................................................................
...................................................................................................................................................................................................
....................................................................................................................................................................................................................................
8-106 Alcatel-Lucent Proprietary Alcatel-Lucent 9311 Macro V2 OD
Use pursuant to applicable agreements NN-20500-011 UA08.1
Issue 09.07 January 2013
9311 Macro V2 OD corrective maintenance procedures Replacing the Cabinet Control Unit (CCU) module
Replacing the power system equipment
....................................................................................................................................................................................................................................
Intervention time
15 minutes
Tools required
Flat screwdriver
Phillips screwdriver
WARNING
Electric-shock hazard
Some parts of all electrical installations are energized. Failure to follow safe work
practices and the safety warnings may lead to bodily injury and property damage. For
this reason, only trained and qualified personnel (electrical workers as defined in IEC
60215 or EN 60215 + A1 or in the National Electrical Code or in ANSI/NFPA No.10)
may install or service the installation.
NOTICE
Service-disruption hazard
This procedure will result in service disruption. Notify the OMC administrator of a
service outage before commencing.
NOTICE
ESD hazard
Electronic components can be destroyed by electrostatic discharge (ESD). Hold circuit
packs only at the edges or on the insertion and removal facilities. Always observe the
general ESD instructions.
Important! Before visiting the site, check that there has been no mains power failure
on the site within the last 48 hours. After a mains power failure, the cabinet must
operate on the mains for at least 24 hours to reload the batteries.
Procedure
...................................................................................................................................................................................................
2 Locate the CCU module. (See Figure 5-3, 9311 Macro V2 OD 2100 cabinet layout
(p. 5-5).)
...................................................................................................................................................................................................
...................................................................................................................................................................................................
5 Undo the two fixing screws (1) on the CCU front panel.
....................................................................................................................................................................................................................................
8-108 Alcatel-Lucent Proprietary Alcatel-Lucent 9311 Macro V2 OD
Use pursuant to applicable agreements NN-20500-011 UA08.1
Issue 09.07 January 2013
9311 Macro V2 OD corrective maintenance procedures Replacing the Cabinet Control Unit (CCU) module
Replacing the power system equipment
....................................................................................................................................................................................................................................
...................................................................................................................................................................................................
7 Insert the new CCU module into the cabinet, on the top and bottom edges.
...................................................................................................................................................................................................
....................................................................................................................................................................................................................................
Alcatel-Lucent 9311 Macro V2 OD Alcatel-Lucent Proprietary 8-109
NN-20500-011 UA08.1 Use pursuant to applicable agreements
Issue 09.07 January 2013
9311 Macro V2 OD corrective maintenance procedures Replacing the UCPS rectifiers
Replacing the power system equipment
....................................................................................................................................................................................................................................
Intervention time
Five minutes
Tools required
None
Procedure
...................................................................................................................................................................................................
....................................................................................................................................................................................................................................
8-110 Alcatel-Lucent Proprietary Alcatel-Lucent 9311 Macro V2 OD
Use pursuant to applicable agreements NN-20500-011 UA08.1
Issue 09.07 January 2013
9311 Macro V2 OD corrective maintenance procedures Replacing the UCPS rectifiers
Replacing the power system equipment
....................................................................................................................................................................................................................................
...................................................................................................................................................................................................
3 Undo the two fixing screws (2) on the front panel of the defective rectifier.
...................................................................................................................................................................................................
....................................................................................................................................................................................................................................
Alcatel-Lucent 9311 Macro V2 OD Alcatel-Lucent Proprietary 8-111
NN-20500-011 UA08.1 Use pursuant to applicable agreements
Issue 09.07 January 2013
9311 Macro V2 OD corrective maintenance procedures Replacing the rectifier rack and DDU
Replacing the power system equipment
....................................................................................................................................................................................................................................
Intervention time
30 minutes
Tools required
Phillips screwdriver
Torque wrench with socket
7-mm wrench
8-mm wrench
17-mm wrench
Flat screwdriver
WARNING
Electric-shock hazard
Some parts of all electrical installations are energized. Failure to follow safe work
practices and the safety warnings may lead to bodily injury and property damage. For
this reason, only trained and qualified personnel (electrical workers as defined in IEC
60215 or EN 60215 + A1 or in the National Electrical Code or in ANSI/NFPA No.10)
may install or service the installation.
NOTICE
ESD hazard
Electronic components can be destroyed by electrostatic discharge (ESD). Hold circuit
packs only at the edges or on the insertion and removal facilities. Always observe the
general ESD instructions.
Important! The tightening torque for the front panel screws must be 0.25 N.m
(0.2375 N.m to 0.2625 N.m).
Important! During the replacement, the service is lost if the ac box breaks down.
Notify the OMC administrator in case of service interruption.
....................................................................................................................................................................................................................................
8-112 Alcatel-Lucent Proprietary Alcatel-Lucent 9311 Macro V2 OD
Use pursuant to applicable agreements NN-20500-011 UA08.1
Issue 09.07 January 2013
9311 Macro V2 OD corrective maintenance procedures Replacing the rectifier rack and DDU
Replacing the power system equipment
....................................................................................................................................................................................................................................
Important! Before visiting the site, check that there has been no mains power failure
on the site within the last 48 hours. After a mains power failure, the cabinet must
operate on the mains for at least 24 hours to reload the batteries.
Procedure
...................................................................................................................................................................................................
5 Undo the six fixing screws (1) on the front panel of the rectifier rack.
....................................................................................................................................................................................................................................
Alcatel-Lucent 9311 Macro V2 OD Alcatel-Lucent Proprietary 8-113
NN-20500-011 UA08.1 Use pursuant to applicable agreements
Issue 09.07 January 2013
9311 Macro V2 OD corrective maintenance procedures Replacing the rectifier rack and DDU
Replacing the power system equipment
....................................................................................................................................................................................................................................
...................................................................................................................................................................................................
6 Slide out the rack and disconnect the ground cable and three AC connectors on the back
of the rack.
...................................................................................................................................................................................................
....................................................................................................................................................................................................................................
8-114 Alcatel-Lucent Proprietary Alcatel-Lucent 9311 Macro V2 OD
Use pursuant to applicable agreements NN-20500-011 UA08.1
Issue 09.07 January 2013
9311 Macro V2 OD corrective maintenance procedures Replacing the rectifier rack and DDU
Replacing the power system equipment
....................................................................................................................................................................................................................................
NOR 40045
NOR 40055
...................................................................................................................................................................................................
9 Remove the CCU board. (See Replacing the Cabinet Control Unit (CCU) module
(p. 8-107).)
...................................................................................................................................................................................................
12 Position the new rack, connect the ground cable and three AC connectors on its back,
and insert it in place.
...................................................................................................................................................................................................
13 Tighten the six fixing screws on the front panel of the rectifier rack.
...................................................................................................................................................................................................
....................................................................................................................................................................................................................................
Alcatel-Lucent 9311 Macro V2 OD Alcatel-Lucent Proprietary 8-115
NN-20500-011 UA08.1 Use pursuant to applicable agreements
Issue 09.07 January 2013
9311 Macro V2 OD corrective maintenance procedures Replacing the rectifier rack and DDU
Replacing the power system equipment
....................................................................................................................................................................................................................................
...................................................................................................................................................................................................
....................................................................................................................................................................................................................................
8-116 Alcatel-Lucent Proprietary Alcatel-Lucent 9311 Macro V2 OD
Use pursuant to applicable agreements NN-20500-011 UA08.1
Issue 09.07 January 2013
9311 Macro V2 OD corrective maintenance procedures Replacing the batteries
Replacing the power system equipment
....................................................................................................................................................................................................................................
Intervention time
One hour
Tools required
10-mm wrench
Torque wrench with socket
WARNING
Electric-shock hazard
Some parts of all electrical installations are energized. Failure to follow safe work
practices and the safety warnings may lead to bodily injury and property damage. For
this reason, only trained and qualified personnel (electrical workers as defined in IEC
60215 or EN 60215 + A1 or in the National Electrical Code or in ANSI/NFPA No.10)
may install or service the installation.
WARNING
Electric-shock hazard
Never replace a power supply when energized.
Important! During the replacement, the service is lost if the ac box breaks down.
Notify the OMC administrator in case of service interruption.
Important! Before visiting the site, check that there has no main power failure on the
site within the last 48 hours.
After a mains power failure, the cabinet must operate on the mains for at least 24
hours to reload the batteries.
Procedure
...................................................................................................................................................................................................
....................................................................................................................................................................................................................................
Alcatel-Lucent 9311 Macro V2 OD Alcatel-Lucent Proprietary 8-117
NN-20500-011 UA08.1 Use pursuant to applicable agreements
Issue 09.07 January 2013
9311 Macro V2 OD corrective maintenance procedures Replacing the batteries
Replacing the power system equipment
....................................................................................................................................................................................................................................
...................................................................................................................................................................................................
....................................................................................................................................................................................................................................
8-118 Alcatel-Lucent Proprietary Alcatel-Lucent 9311 Macro V2 OD
Use pursuant to applicable agreements NN-20500-011 UA08.1
Issue 09.07 January 2013
9311 Macro V2 OD corrective maintenance procedures Replacing the batteries
Replacing the power system equipment
....................................................................................................................................................................................................................................
...................................................................................................................................................................................................
5 WARNING
Electric-shock hazard
Battery short circuits may be caused from contact with metal objects causing burns to the
face and hands as well as damage to the equipment.
You must therefore ensure the following:
Always use insulated tools when working with or near batteries.
Always use insulated tools when working with or near batteries.
Never place metallic objects on the batteries.
Do not wear jewelry (watches, metal rings or bracelets).
Do not wear outer clothing composed of synthetic material (e.g. nylon).
Remove the NOR 40009 cable. (See legend 3 in Figure 8-49, Batteries cabling
(p. 8-123) figure.)
....................................................................................................................................................................................................................................
Alcatel-Lucent 9311 Macro V2 OD Alcatel-Lucent Proprietary 8-119
NN-20500-011 UA08.1 Use pursuant to applicable agreements
Issue 09.07 January 2013
9311 Macro V2 OD corrective maintenance procedures Replacing the batteries
Replacing the power system equipment
....................................................................................................................................................................................................................................
...................................................................................................................................................................................................
6 WARNING
Electric-shock hazard
Battery short circuits may be caused from contact with metal objects causing burns to the
face and hands as well as damage to the equipment.
You must therefore ensure the following:
Always use insulated tools when working with or near batteries.
Always use insulated tools when working with or near batteries.
Never place metallic objects on the batteries.
Do not wear jewelry (watches, metal rings or bracelets).
Do not wear outer clothing composed of synthetic material (e.g. nylon).
Remove the NOR 40010 cable. (See legend 5 in Figure 8-49, Batteries cabling
(p. 8-123) figure.)
...................................................................................................................................................................................................
7 WARNING
Electric-shock hazard
Battery short circuits may be caused from contact with metal objects causing burns to the
face and hands as well as damage to the equipment.
You must therefore ensure the following:
Always use insulated tools when working with or near batteries.
Always use insulated tools when working with or near batteries.
Never place metallic objects on the batteries.
Do not wear jewelry (watches, metal rings or bracelets).
Do not wear outer clothing composed of synthetic material (e.g. nylon).
Remove the three cables (usually black; see legend 4 in Figure 8-49, Batteries cabling
(p. 8-123) figure) between batteries, delivered with the battery kit.
Disconnect batteries one by one, starting with terminals (-) at the bottom.
...................................................................................................................................................................................................
....................................................................................................................................................................................................................................
8-120 Alcatel-Lucent Proprietary Alcatel-Lucent 9311 Macro V2 OD
Use pursuant to applicable agreements NN-20500-011 UA08.1
Issue 09.07 January 2013
9311 Macro V2 OD corrective maintenance procedures Replacing the batteries
Replacing the power system equipment
....................................................................................................................................................................................................................................
Two M8 wing nuts (see legend 2 in Figure 8-49, Batteries cabling
(p. 8-123) figure.)
The plate blocking the batteries (see legend 1 in Figure 8-49, Batteries cabling
(p. 8-123) figure.)
...................................................................................................................................................................................................
9 Remove the RF diversity cable on the second cell (DDM; see legend 15 in Figure 5-3,
9311 Macro V2 OD 2100 cabinet layout (p. 5-5)) to allow battery removal.
...................................................................................................................................................................................................
11 NOTICE
Working instruction
The four batteries must be identical (brand, data-code, reference number), therefore the
whole set must be replaced.
Replace the batteries only with the same or equivalent type recommended by the
manufacturer.
Dispose of used batteries according to the manufacturer instructions.
Reinsert the four new batteries.
....................................................................................................................................................................................................................................
Alcatel-Lucent 9311 Macro V2 OD Alcatel-Lucent Proprietary 8-121
NN-20500-011 UA08.1 Use pursuant to applicable agreements
Issue 09.07 January 2013
9311 Macro V2 OD corrective maintenance procedures Replacing the batteries
Replacing the power system equipment
....................................................................................................................................................................................................................................
...................................................................................................................................................................................................
....................................................................................................................................................................................................................................
8-122 Alcatel-Lucent Proprietary Alcatel-Lucent 9311 Macro V2 OD
Use pursuant to applicable agreements NN-20500-011 UA08.1
Issue 09.07 January 2013
9311 Macro V2 OD corrective maintenance procedures Replacing the batteries
Replacing the power system equipment
....................................................................................................................................................................................................................................
...................................................................................................................................................................................................
....................................................................................................................................................................................................................................
Alcatel-Lucent 9311 Macro V2 OD Alcatel-Lucent Proprietary 8-123
NN-20500-011 UA08.1 Use pursuant to applicable agreements
Issue 09.07 January 2013
9311 Macro V2 OD corrective maintenance procedures Replacing the batteries
Replacing the power system equipment
....................................................................................................................................................................................................................................
...................................................................................................................................................................................................
....................................................................................................................................................................................................................................
8-124 Alcatel-Lucent Proprietary Alcatel-Lucent 9311 Macro V2 OD
Use pursuant to applicable agreements NN-20500-011 UA08.1
Issue 09.07 January 2013
9311 Macro V2 OD corrective maintenance procedures Overview
Replacing the optional equipment
....................................................................................................................................................................................................................................
Overview
Purpose
This section presents the replacement procedures of modules not contained in the digital
shelf and RF block.
Contents
....................................................................................................................................................................................................................................
Alcatel-Lucent 9311 Macro V2 OD Alcatel-Lucent Proprietary 8-125
NN-20500-011 UA08.1 Use pursuant to applicable agreements
Issue 09.07 January 2013
9311 Macro V2 OD corrective maintenance procedures Replacing the Manufacturing Commissioning and Alarm
Replacing the optional equipment (MCA) module
....................................................................................................................................................................................................................................
Intervention time
Ten minutes
Tools required
Phillips screwdriver
Local Installation Terminal (TIL)
NOTICE
ESD hazard
Electronic components can be destroyed by electrostatic discharge (ESD). Hold circuit
packs only at the edges or on the insertion and removal facilities. Always observe the
general ESD instructions.
NOTICE
Service-disruption hazard
This procedure will result in service disruption. Notify the OMC administrator of a
service outage before commencing.
Important! The personnel working on the cabinet must be authorized to work
according to the security standards.
Procedure
...................................................................................................................................................................................................
1 Important! If you have to leave the site because it is not possible to obtain an MCA
backup file quickly, do not change the faulty MCA and disconnect the PCM cable
from the CCM front panel.
Open the Node B doors.
....................................................................................................................................................................................................................................
8-126 Alcatel-Lucent Proprietary Alcatel-Lucent 9311 Macro V2 OD
Use pursuant to applicable agreements NN-20500-011 UA08.1
Issue 09.07 January 2013
9311 Macro V2 OD corrective maintenance procedures Replacing the Manufacturing Commissioning and Alarm
Replacing the optional equipment (MCA) module
....................................................................................................................................................................................................................................
...................................................................................................................................................................................................
3 Apply the "Creating the MCA backup file" procedure defined in Alcatel-Lucent 9100 and
93xx Node B - Commissioning and Fault Management User Manual: TIL,
NN-20500-019.
...................................................................................................................................................................................................
5 Disconnect the cable (RoHS PEC: NTN097DF) with three connectors on the MCA.
...................................................................................................................................................................................................
....................................................................................................................................................................................................................................
Alcatel-Lucent 9311 Macro V2 OD Alcatel-Lucent Proprietary 8-127
NN-20500-011 UA08.1 Use pursuant to applicable agreements
Issue 09.07 January 2013
9311 Macro V2 OD corrective maintenance procedures Replacing the Manufacturing Commissioning and Alarm
Replacing the optional equipment (MCA) module
....................................................................................................................................................................................................................................
...................................................................................................................................................................................................
11 Apply the "Updating an empty MCA module" procedure defined in Alcatel-Lucent 9100
and 93xx Node B - Commissioning and Fault Management User Manual: TIL,
NN-20500-019.
....................................................................................................................................................................................................................................
8-128 Alcatel-Lucent Proprietary Alcatel-Lucent 9311 Macro V2 OD
Use pursuant to applicable agreements NN-20500-011 UA08.1
Issue 09.07 January 2013
9311 Macro V2 OD corrective maintenance procedures Replacing the Manufacturing Commissioning and Alarm
Replacing the optional equipment (MCA) module
....................................................................................................................................................................................................................................
...................................................................................................................................................................................................
12 If the message is MCA update forbidden, call the next level of support.
...................................................................................................................................................................................................
17 Disconnect the cable (RoHS PEC: NTN097DF) with three connectors on the MCA.
...................................................................................................................................................................................................
18 Undo the two fixing screws on the front panel of the MCA.
...................................................................................................................................................................................................
21 Tighten the two fixing screws on the front panel of the MCA.
...................................................................................................................................................................................................
....................................................................................................................................................................................................................................
Alcatel-Lucent 9311 Macro V2 OD Alcatel-Lucent Proprietary 8-129
NN-20500-011 UA08.1 Use pursuant to applicable agreements
Issue 09.07 January 2013
9311 Macro V2 OD corrective maintenance procedures Replacing the Manufacturing Commissioning and Alarm
Replacing the optional equipment (MCA) module
....................................................................................................................................................................................................................................
...................................................................................................................................................................................................
23 Apply the "Updating an empty MCA module" procedure defined in Alcatel-Lucent 9100
and 93xx Node B - Commissioning and Fault Management User Manual: TIL,
NN-20500-019.
...................................................................................................................................................................................................
24 If the message is MCA update forbidden, call the next level of support.
...................................................................................................................................................................................................
....................................................................................................................................................................................................................................
8-130 Alcatel-Lucent Proprietary Alcatel-Lucent 9311 Macro V2 OD
Use pursuant to applicable agreements NN-20500-011 UA08.1
Issue 09.07 January 2013
9311 Macro V2 OD corrective maintenance procedures Replacing the alarm protection module
Replacing the optional equipment
....................................................................................................................................................................................................................................
Intervention time
Ten minutes
Tools required
Screwdriver
Wrench for hexagonal head nut (M6 nut)
....................................................................................................................................................................................................................................
Alcatel-Lucent 9311 Macro V2 OD Alcatel-Lucent Proprietary 8-131
NN-20500-011 UA08.1 Use pursuant to applicable agreements
Issue 09.07 January 2013
9311 Macro V2 OD corrective maintenance procedures Replacing the alarm protection module
Replacing the optional equipment
....................................................................................................................................................................................................................................
NOTICE
ESD hazard
Electronic components can be destroyed by electrostatic discharge (ESD). Hold circuit
packs only at the edges or on the insertion and removal facilities. Always observe the
general ESD instructions.
Important! Notify the OMC administrator of the alarm protection module
replacement.
....................................................................................................................................................................................................................................
8-132 Alcatel-Lucent Proprietary Alcatel-Lucent 9311 Macro V2 OD
Use pursuant to applicable agreements NN-20500-011 UA08.1
Issue 09.07 January 2013
9311 Macro V2 OD corrective maintenance procedures Replacing the alarm protection module
Replacing the optional equipment
....................................................................................................................................................................................................................................
Procedure
...................................................................................................................................................................................................
4 Remove the two connectors from the bulkhead and undo the wiring.
...................................................................................................................................................................................................
10 Reconnect the two connectors to the bulkhead and redo the wiring.
...................................................................................................................................................................................................
11 Check with the OMC administrator that all alarms are OK.
...................................................................................................................................................................................................
....................................................................................................................................................................................................................................
Alcatel-Lucent 9311 Macro V2 OD Alcatel-Lucent Proprietary 8-133
NN-20500-011 UA08.1 Use pursuant to applicable agreements
Issue 09.07 January 2013
9311 Macro V2 OD corrective maintenance procedures Replacing the double TMA module
Replacing the optional equipment
....................................................................................................................................................................................................................................
Intervention time
15 minutes
Tools required
7/16 torque wrench
13-mm open wrench
Flat screwdriver
Phillips screwdriver
Note: Tightening torques are specified within the procedure.
The following figure shows the double TMA set-up diagram.
....................................................................................................................................................................................................................................
8-134 Alcatel-Lucent Proprietary Alcatel-Lucent 9311 Macro V2 OD
Use pursuant to applicable agreements NN-20500-011 UA08.1
Issue 09.07 January 2013
9311 Macro V2 OD corrective maintenance procedures Replacing the double TMA module
Replacing the optional equipment
....................................................................................................................................................................................................................................
....................................................................................................................................................................................................................................
Alcatel-Lucent 9311 Macro V2 OD Alcatel-Lucent Proprietary 8-135
NN-20500-011 UA08.1 Use pursuant to applicable agreements
Issue 09.07 January 2013
9311 Macro V2 OD corrective maintenance procedures Replacing the double TMA module
Replacing the optional equipment
....................................................................................................................................................................................................................................
CAUTION
RF hazard
RF exposure in excess of applicable limits can result in serious personal injury.
Observe the following:
Turn off and lockout the transmit power before working on the antenna system.
If the transmitters must be tested with the antennas connected, adhere to appropriate
antenna stand-off distances.
Do not use auxiliary antennas.
Consult with the Antenna exposure statements before begining work.
NOTICE
Service-disruption hazard
Following the procedure below will result in a loss of service.
NOTICE
ESD hazard
Electronic components can be destroyed by electrostatic discharge (ESD). Hold circuit
packs only at the edges or on the insertion and removal facilities. Always observe the
general ESD instructions.
Procedure
...................................................................................................................................................................................................
2 If the Node B is operational and connected to the OMC, ask the OMC administrator to
lock the sector associated with the faulty TMA (by Set Administrative State). For more
information, please refer to Alcatel-Lucent 9353 Wireless Management System - User
Guide, NN-20500-032.
...................................................................................................................................................................................................
....................................................................................................................................................................................................................................
8-136 Alcatel-Lucent Proprietary Alcatel-Lucent 9311 Macro V2 OD
Use pursuant to applicable agreements NN-20500-011 UA08.1
Issue 09.07 January 2013
9311 Macro V2 OD corrective maintenance procedures Replacing the double TMA module
Replacing the optional equipment
....................................................................................................................................................................................................................................
...................................................................................................................................................................................................
4 Disconnect the four RF cables from the TMA using the torque wrench.
...................................................................................................................................................................................................
6 Disconnect the ground cable by untightening the nut from the TMA using the 13-mm
wrench.
...................................................................................................................................................................................................
7 On the support plate, untighten the four screws on the support side by using the Phillips
screwdriver.
...................................................................................................................................................................................................
8 Untighten the four nuts which firmly anchor the TMA to the support plate, and remove
the faulty TMA module.
...................................................................................................................................................................................................
9 Append the new TMA module and fix it to the support side with all four screws.
...................................................................................................................................................................................................
10 Tighten the four nuts to firmly anchor the TMA to the support plate.
...................................................................................................................................................................................................
12 Remove the screw, the two flat washers, and the split washer. Take care not to lose items
during the removal.
...................................................................................................................................................................................................
14 Connect the ground cable to the TMA by assembling the following components in the
following order:
Flat washer
Eyelet terminal
Flat washer
Split washer
Hexagonal nut
....................................................................................................................................................................................................................................
Alcatel-Lucent 9311 Macro V2 OD Alcatel-Lucent Proprietary 8-137
NN-20500-011 UA08.1 Use pursuant to applicable agreements
Issue 09.07 January 2013
9311 Macro V2 OD corrective maintenance procedures Replacing the double TMA module
Replacing the optional equipment
....................................................................................................................................................................................................................................
...................................................................................................................................................................................................
15 Tighten the ground cable using the 13-mm wrench. Check that the other end of the cable
is connected to an efficient ground point.
...................................................................................................................................................................................................
18 Tighten the RF connectors to the TMA using the torque wrench, setting the torque to the
maximum value recommended by the supplier of the 7/16 male connector.
Note: Tighten with 25 N.m in case there is no detailed instruction available from the
connector manufacturer.
Result: The TMA is installed with all connections completed.
...................................................................................................................................................................................................
19 Ask the OMC administrator to unlock the sector associated with the faulty TMA and
previously locked on step 2.
...................................................................................................................................................................................................
20 Check that the TMA LED on the DDM is OFF. For more information about the TMA
LED status, please refer to Alcatel-Lucent 9311 Macro Node B Outdoor Technical
Description, NN-20500-004.
...................................................................................................................................................................................................
21 Check the VSWR LEDs (VSWR thresholds) on the DDM. For more information about
the VSWR LED status, please refer to Alcatel-Lucent 9311 Macro Node B Outdoor
Technical Description, NN-20500-004.
...................................................................................................................................................................................................
....................................................................................................................................................................................................................................
8-138 Alcatel-Lucent Proprietary Alcatel-Lucent 9311 Macro V2 OD
Use pursuant to applicable agreements NN-20500-011 UA08.1
Issue 09.07 January 2013
9311 Macro V2 OD corrective maintenance procedures Replacing the light TMA/AISG TMA module
Replacing the optional equipment
....................................................................................................................................................................................................................................
Intervention time
15 minutes
Tools required
7/16 torque wrench
13-mm open wrench
17-mm torque wrench
Cutting pliers
Note: Tightening torques are specified within the procedure.
The following figure shows the light TMA set-up diagram.
....................................................................................................................................................................................................................................
Alcatel-Lucent 9311 Macro V2 OD Alcatel-Lucent Proprietary 8-139
NN-20500-011 UA08.1 Use pursuant to applicable agreements
Issue 09.07 January 2013
9311 Macro V2 OD corrective maintenance procedures Replacing the light TMA/AISG TMA module
Replacing the optional equipment
....................................................................................................................................................................................................................................
....................................................................................................................................................................................................................................
8-140 Alcatel-Lucent Proprietary Alcatel-Lucent 9311 Macro V2 OD
Use pursuant to applicable agreements NN-20500-011 UA08.1
Issue 09.07 January 2013
9311 Macro V2 OD corrective maintenance procedures Replacing the light TMA/AISG TMA module
Replacing the optional equipment
....................................................................................................................................................................................................................................
WARNING
Electric-shock hazard
Some parts of all electrical installations are energized. Failure to follow safe work
practices and the safety warnings may lead to bodily injury and property damage. For
this reason, only trained and qualified personnel (electrical workers as defined in IEC
60215 or EN 60215 + A1 or in the National Electrical Code or in ANSI/NFPA No.10)
may install or service the installation.
Important! Only authorized personnel, with adequate technical training and expertise
with radio base systems will be permitted to operate on the various units. Opening of
enclosed units is not permitted.
CAUTION
RF hazard
RF exposure in excess of applicable limits can result in serious personal injury.
Observe the following:
Turn off and lockout the transmit power before working on the antenna system.
If the transmitters must be tested with the antennas connected, adhere to appropriate
antenna stand-off distances.
Do not use auxiliary antennas.
Consult with the Antenna exposure statements before begining work.
NOTICE
Service-disruption hazard
Following the procedure below will result in a loss of service.
You must notify the OMC administrator.
NOTICE
ESD hazard
Electronic components can be destroyed by electrostatic discharge (ESD). Hold circuit
packs only at the edges or on the insertion and removal facilities. Always observe the
general ESD instructions.
Important! Observe the general safety precaution against injury and equipment
damage outlined in the regional installation safety manual at all times.
....................................................................................................................................................................................................................................
Alcatel-Lucent 9311 Macro V2 OD Alcatel-Lucent Proprietary 8-141
NN-20500-011 UA08.1 Use pursuant to applicable agreements
Issue 09.07 January 2013
9311 Macro V2 OD corrective maintenance procedures Replacing the light TMA/AISG TMA module
Replacing the optional equipment
....................................................................................................................................................................................................................................
Appropriate precautions must be taken to guarantee the safety of staff and equipment.
All operations to perform the connection of the TMA module to the Node B must be
done according to the safety instructions; please contact your Node B supplier for
valid instruction.
Procedure
...................................................................................................................................................................................................
2 If the Node B is operational and connected to the OMC, ask the OMC administrator to
lock the sector associated with the faulty TMA (by Set Administrative State). For more
information, please refer to Alcatel-Lucent 9353 Wireless Management System - User
Guide, NN-20500-032.
...................................................................................................................................................................................................
4 Disconnect the ground cable by untightening the nut from the TMA using the 13-mm
open wrench.
...................................................................................................................................................................................................
5 Disconnect the four jumper cables from the TMA RF connectors using the 7/16 torque
wrench.
Note: For AISG TMA, disconnect the AISG cable using the 7/16 torque wrench.
...................................................................................................................................................................................................
....................................................................................................................................................................................................................................
8-142 Alcatel-Lucent Proprietary Alcatel-Lucent 9311 Macro V2 OD
Use pursuant to applicable agreements NN-20500-011 UA08.1
Issue 09.07 January 2013
9311 Macro V2 OD corrective maintenance procedures Replacing the light TMA/AISG TMA module
Replacing the optional equipment
....................................................................................................................................................................................................................................
...................................................................................................................................................................................................
12 Move the steel band into the openings of the TMA mounting equipment.
...................................................................................................................................................................................................
13 Tighten the hose clamp screws carefully. Do not over tighten them.
...................................................................................................................................................................................................
14 Connect the four jumper cables to the TMA RF connectors using the 7/16 torque wrench.
....................................................................................................................................................................................................................................
Alcatel-Lucent 9311 Macro V2 OD Alcatel-Lucent Proprietary 8-143
NN-20500-011 UA08.1 Use pursuant to applicable agreements
Issue 09.07 January 2013
9311 Macro V2 OD corrective maintenance procedures Replacing the light TMA/AISG TMA module
Replacing the optional equipment
....................................................................................................................................................................................................................................
Note: Tightening torques must be the following:
25-30 N.m (35-40 Ibf ft) for 7/16 connectors
6 N.m (8 Ibf ft) for N-type connectors
...................................................................................................................................................................................................
15 For AISG TMA, reconnect the AISG cable using the 7/16 torque wrench. Tightening
torque is 25-30 N.m (35-40 Ibf ft).
Result: The TMA is installed when all connections are completed.
...................................................................................................................................................................................................
16 Reconnect the ground cable using the 13-mm open wrench. Tightening torque is 5 N.m
(3.7 Ibf ft).
...................................................................................................................................................................................................
17 Ask the OMC administrator to unlock the sector associated with the faulty TMA and
previously locked on step 2.
...................................................................................................................................................................................................
18 Check that the TMA LED on the DDM is OFF. For more information about the TMA
LED status, please refer to Alcatel-Lucent 9311 Macro Node B Outdoor Technical
Description, NN-20500-004.
...................................................................................................................................................................................................
19 Check the VSWR LEDs (VSWR thresholds) on the DDM. For more information about
the VSWR LED status, please refer to Alcatel-Lucent 9311 Macro Node B Outdoor
Technical Description, NN-20500-004.
...................................................................................................................................................................................................
....................................................................................................................................................................................................................................
8-144 Alcatel-Lucent Proprietary Alcatel-Lucent 9311 Macro V2 OD
Use pursuant to applicable agreements NN-20500-011 UA08.1
Issue 09.07 January 2013
9311 Macro V2 OD corrective maintenance procedures Replacing the Power Amplifier InterCOnnection (PA ICO)
Replacing the optional equipment module
....................................................................................................................................................................................................................................
Intervention time
15 minutes
Tools required
Phillips screwdriver
Threaded 10
Ty-raps
WARNING
Electric-shock hazard
Some parts of all electrical installations are energized. Failure to follow safe work
practices and the safety warnings may lead to bodily injury and property damage. For
this reason, only trained and qualified personnel (electrical workers as defined in IEC
60215 or EN 60215 + A1 or in the National Electrical Code or in ANSI/NFPA No.10)
may install or service the installation.
NOTICE
ESD hazard
Electronic components can be destroyed by electrostatic discharge (ESD). Hold circuit
packs only at the edges or on the insertion and removal facilities. Always observe the
general ESD instructions.
Important! During the replacement, the service is lost if the AC box breaks down.
Notify the OMC administrator in case of service interruption.
Procedure
...................................................................................................................................................................................................
....................................................................................................................................................................................................................................
Alcatel-Lucent 9311 Macro V2 OD Alcatel-Lucent Proprietary 8-145
NN-20500-011 UA08.1 Use pursuant to applicable agreements
Issue 09.07 January 2013
9311 Macro V2 OD corrective maintenance procedures Replacing the Power Amplifier InterCOnnection (PA ICO)
Replacing the optional equipment module
....................................................................................................................................................................................................................................
...................................................................................................................................................................................................
6 Disconnect the nine plain-plugs on the back of the PA ICO (see Figure 8-55, PA ICO
module (p. 8-147)).
....................................................................................................................................................................................................................................
8-146 Alcatel-Lucent Proprietary Alcatel-Lucent 9311 Macro V2 OD
Use pursuant to applicable agreements NN-20500-011 UA08.1
Issue 09.07 January 2013
9311 Macro V2 OD corrective maintenance procedures Replacing the Power Amplifier InterCOnnection (PA ICO)
Replacing the optional equipment module
....................................................................................................................................................................................................................................
...................................................................................................................................................................................................
....................................................................................................................................................................................................................................
Alcatel-Lucent 9311 Macro V2 OD Alcatel-Lucent Proprietary 8-147
NN-20500-011 UA08.1 Use pursuant to applicable agreements
Issue 09.07 January 2013
9311 Macro V2 OD corrective maintenance procedures Replacing the Power Amplifier InterCOnnection (PA ICO)
Replacing the optional equipment module
....................................................................................................................................................................................................................................
...................................................................................................................................................................................................
10 Reconnect the fasten-lug on the right side of the PA ICO (RF ICO fuse).
...................................................................................................................................................................................................
11 Reconnect the nine plain-lugs on the back of the PA ICO (see Figure 8-55, PA ICO
module (p. 8-147)).
...................................................................................................................................................................................................
....................................................................................................................................................................................................................................
8-148 Alcatel-Lucent Proprietary Alcatel-Lucent 9311 Macro V2 OD
Use pursuant to applicable agreements NN-20500-011 UA08.1
Issue 09.07 January 2013
9311 Macro V2 OD corrective maintenance procedures Replacing the Radio Frequency InterCOnnection (RF ICO)
Replacing the optional equipment module
....................................................................................................................................................................................................................................
Intervention time
Ten minutes
Tools required
Phillips screwdriver
WARNING
Electric-shock hazard
Some parts of all electrical installations are energized. Failure to follow safe work
practices and the safety warnings may lead to bodily injury and property damage. For
this reason, only trained and qualified personnel (electrical workers as defined in IEC
60215 or EN 60215 + A1 or in the National Electrical Code or in ANSI/NFPA No.10)
may install or service the installation.
NOTICE
ESD hazard
Electronic components can be destroyed by electrostatic discharge (ESD). Hold circuit
packs only at the edges or on the insertion and removal facilities. Always observe the
general ESD instructions.
Important! During the replacement, the service is lost if the ac box breaks down.
Notify the OMC administrator in case of service interruption.
Procedure
...................................................................................................................................................................................................
2 Locate the RF ICO on the left column, on top of the three DDMs. (See legend 16 in
Figure 5-3, 9311 Macro V2 OD 2100 cabinet layout (p. 5-5).)
...................................................................................................................................................................................................
...................................................................................................................................................................................................
....................................................................................................................................................................................................................................
8-150 Alcatel-Lucent Proprietary Alcatel-Lucent 9311 Macro V2 OD
Use pursuant to applicable agreements NN-20500-011 UA08.1
Issue 09.07 January 2013
9311 Macro V2 OD corrective maintenance procedures Replacing the Radio Frequency InterCOnnection (RF ICO)
Replacing the optional equipment module
....................................................................................................................................................................................................................................
...................................................................................................................................................................................................
9 Connect the three plain-lugs as follows (see Figure 8-56, RF ICO module (p. 8-150)):
Blue cable on top
Black cable in the middle
Green/yellow cable at the bottom
...................................................................................................................................................................................................
....................................................................................................................................................................................................................................
Alcatel-Lucent 9311 Macro V2 OD Alcatel-Lucent Proprietary 8-151
NN-20500-011 UA08.1 Use pursuant to applicable agreements
Issue 09.07 January 2013
9311 Macro V2 OD corrective maintenance procedures Replacing the door gaskets
Replacing the optional equipment
....................................................................................................................................................................................................................................
Intervention time
30 minutes on each door gasket
Tools required
Flat and Phillips head screwdrivers
Clean lint free cloths
Non-metallic low abrasive pad
Gasket PSA roller (Chromatics Ref.C589R1, Grolleau Ref.0985A)
Rubber gloves (powder free)
One of the following:
3M natural cleaner
Acetone
MEK
Note: To finish cleaning the surface and apply the new gasket, use the following
tools:
Wooden tongue depressor or equivalent
Distilled water
90% or higher concentration alcohol
WARNING
Electric-shock hazard
Some parts of all electrical installations are energized. Failure to follow safe work
practices and the safety warnings may lead to bodily injury and property damage. For
this reason, only trained and qualified personnel (electrical workers as defined in IEC
60215 or EN 60215 + A1 or in the National Electrical Code or in ANSI/NFPA No.10)
may install or service the installation.
....................................................................................................................................................................................................................................
8-152 Alcatel-Lucent Proprietary Alcatel-Lucent 9311 Macro V2 OD
Use pursuant to applicable agreements NN-20500-011 UA08.1
Issue 09.07 January 2013
9311 Macro V2 OD corrective maintenance procedures Replacing the door gaskets
Replacing the optional equipment
....................................................................................................................................................................................................................................
NOTICE
ESD hazard
Electronic components can be destroyed by electrostatic discharge (ESD). Hold circuit
packs only at the edges or on the insertion and removal facilities. Always observe the
general ESD instructions.
Important! This procedure requires to be in contact with the OMC administrator.
Procedure
...................................................................................................................................................................................................
....................................................................................................................................................................................................................................
Alcatel-Lucent 9311 Macro V2 OD Alcatel-Lucent Proprietary 8-153
NN-20500-011 UA08.1 Use pursuant to applicable agreements
Issue 09.07 January 2013
9311 Macro V2 OD corrective maintenance procedures Replacing the door gaskets
Replacing the optional equipment
....................................................................................................................................................................................................................................
...................................................................................................................................................................................................
....................................................................................................................................................................................................................................
8-154 Alcatel-Lucent Proprietary Alcatel-Lucent 9311 Macro V2 OD
Use pursuant to applicable agreements NN-20500-011 UA08.1
Issue 09.07 January 2013
9311 Macro V2 OD corrective maintenance procedures Replacing the door gaskets
Replacing the optional equipment
....................................................................................................................................................................................................................................
...................................................................................................................................................................................................
7 Position the gasket by positioning the four corners of the joint as required.
...................................................................................................................................................................................................
9 Put the gasket in place by pressing firmly on the surface (use the wooden tongue
depressor).
...................................................................................................................................................................................................
13 Close the door and check visually that gasket compression is OK.
...................................................................................................................................................................................................
....................................................................................................................................................................................................................................
Alcatel-Lucent 9311 Macro V2 OD Alcatel-Lucent Proprietary 8-155
NN-20500-011 UA08.1 Use pursuant to applicable agreements
Issue 09.07 January 2013
9311 Macro V2 OD corrective maintenance procedures Replacing the foam gaskets
Replacing the optional equipment
....................................................................................................................................................................................................................................
Intervention time
30 minutes for each foam gasket
Tools required
Flat and Phillips head screwdrivers
Clean lint free cloths
Non-metallic low abrasive pad
Gasket PSA roller (Chromatics Ref.C589R1, Grolleau Ref.0985A)
Rubber gloves (powder free)
One of the following:
3M natural cleaner
Acetone
MEK
Note: To finish cleaning the surface and apply the new gasket, use the following
tools:
Wooden tongue depressor or equivalent
Distilled water
90% or higher concentration alcohol
WARNING
Electric-shock hazard
Some parts of all electrical installations are energized. Failure to follow safe work
practices and the safety warnings may lead to bodily injury and property damage. For
this reason, only trained and qualified personnel (electrical workers as defined in IEC
60215 or EN 60215 + A1 or in the National Electrical Code or in ANSI/NFPA No.10)
may install or service the installation.
....................................................................................................................................................................................................................................
8-156 Alcatel-Lucent Proprietary Alcatel-Lucent 9311 Macro V2 OD
Use pursuant to applicable agreements NN-20500-011 UA08.1
Issue 09.07 January 2013
9311 Macro V2 OD corrective maintenance procedures Replacing the foam gaskets
Replacing the optional equipment
....................................................................................................................................................................................................................................
NOTICE
ESD hazard
Electronic components can be destroyed by electrostatic discharge (ESD). Hold circuit
packs only at the edges or on the insertion and removal facilities. Always observe the
general ESD instructions.
Procedure
...................................................................................................................................................................................................
1
Note: Check with the OMC administrator that the operational state of the
btsSiteManager object is enabled. For more information about the OMC, please refer
to Alcatel-Lucent 9353 Wireless Management System - User Guide, NN-20500-032.
Open the Node B doors.
....................................................................................................................................................................................................................................
Alcatel-Lucent 9311 Macro V2 OD Alcatel-Lucent Proprietary 8-157
NN-20500-011 UA08.1 Use pursuant to applicable agreements
Issue 09.07 January 2013
9311 Macro V2 OD corrective maintenance procedures Replacing the foam gaskets
Replacing the optional equipment
....................................................................................................................................................................................................................................
...................................................................................................................................................................................................
4 Cut a first foam gasket with length L = 735 mm (horizontal foam gasket).
....................................................................................................................................................................................................................................
8-158 Alcatel-Lucent Proprietary Alcatel-Lucent 9311 Macro V2 OD
Use pursuant to applicable agreements NN-20500-011 UA08.1
Issue 09.07 January 2013
9311 Macro V2 OD corrective maintenance procedures Replacing the foam gaskets
Replacing the optional equipment
....................................................................................................................................................................................................................................
...................................................................................................................................................................................................
5 Cut a second foam gasket with length L = 285 mm (vertical foam gasket).
...................................................................................................................................................................................................
8 Position the first foam gasket (L = 735 mm) horizontally as required. (See legends 3 or 4
in Figure 8-58, Foam gasket replacement (p. 8-158).)
...................................................................................................................................................................................................
9 Position the second foam gasket (L = 285 mm) vertically as required. (See legends 2 or 5
in Figure 8-58, Foam gasket replacement (p. 8-158).)
...................................................................................................................................................................................................
11 Put the gaskets in place by pressing firmly on the surface (use the wooden tongue
depressor).
...................................................................................................................................................................................................
14 Close the door and check visually that gasket compression is OK.
...................................................................................................................................................................................................
....................................................................................................................................................................................................................................
Alcatel-Lucent 9311 Macro V2 OD Alcatel-Lucent Proprietary 8-159
NN-20500-011 UA08.1 Use pursuant to applicable agreements
Issue 09.07 January 2013
9311 Macro V2 OD corrective maintenance procedures Replacing the door lock
Replacing the optional equipment
....................................................................................................................................................................................................................................
Intervention time
15 minutes
Tools required
Phillips screwdriver
WARNING
Electric-shock hazard
Some parts of all electrical installations are energized. Failure to follow safe work
practices and the safety warnings may lead to bodily injury and property damage. For
this reason, only trained and qualified personnel (electrical workers as defined in IEC
60215 or EN 60215 + A1 or in the National Electrical Code or in ANSI/NFPA No.10)
may install or service the installation.
NOTICE
ESD hazard
Electronic components can be destroyed by electrostatic discharge (ESD). Hold circuit
packs only at the edges or on the insertion and removal facilities. Always observe the
general ESD instructions.
Important! This procedure requires to be in contact with the OMC administrator.
Procedure
...................................................................................................................................................................................................
....................................................................................................................................................................................................................................
8-160 Alcatel-Lucent Proprietary Alcatel-Lucent 9311 Macro V2 OD
Use pursuant to applicable agreements NN-20500-011 UA08.1
Issue 09.07 January 2013
9311 Macro V2 OD corrective maintenance procedures Replacing the door lock
Replacing the optional equipment
....................................................................................................................................................................................................................................
...................................................................................................................................................................................................
5 Remove the four screws holding the two covers inside the door.
...................................................................................................................................................................................................
...................................................................................................................................................................................................
9 Screw the plastic cover and plastic adaptor with the screw provided in the kit.
....................................................................................................................................................................................................................................
Alcatel-Lucent 9311 Macro V2 OD Alcatel-Lucent Proprietary 8-161
NN-20500-011 UA08.1 Use pursuant to applicable agreements
Issue 09.07 January 2013
9311 Macro V2 OD corrective maintenance procedures Replacing the door lock
Replacing the optional equipment
....................................................................................................................................................................................................................................
...................................................................................................................................................................................................
10 Insert the two adaptors: the small in zamak and the other in aluminium on the handle.
...................................................................................................................................................................................................
11 Tighten the four screws holding the two covers inside the door.
...................................................................................................................................................................................................
....................................................................................................................................................................................................................................
8-162 Alcatel-Lucent Proprietary Alcatel-Lucent 9311 Macro V2 OD
Use pursuant to applicable agreements NN-20500-011 UA08.1
Issue 09.07 January 2013
9311 Macro V2 OD corrective maintenance procedures Replacing the door lock
Replacing the optional equipment
....................................................................................................................................................................................................................................
...................................................................................................................................................................................................
....................................................................................................................................................................................................................................
Alcatel-Lucent 9311 Macro V2 OD Alcatel-Lucent Proprietary 8-163
NN-20500-011 UA08.1 Use pursuant to applicable agreements
Issue 09.07 January 2013
9311 Macro V2 OD corrective maintenance procedures Replacing the User ICO module
Replacing the optional equipment
....................................................................................................................................................................................................................................
Intervention time
Five minutes
Tools required
Phillips screwdriver
Flat blade isolated screwdriver
NOTICE
ESD hazard
Electronic components can be destroyed by electrostatic discharge (ESD). Hold circuit
packs only at the edges or on the insertion and removal facilities. Always observe the
general ESD instructions.
Important! If the AC Distribution Unit (ADU) breaks down during the replacement,
the service is lost.
Notify the OMC administrator in case of service interruption.
Note: The User ICO is powered by the DC Distribution Unit (DDU).
Procedure
...................................................................................................................................................................................................
2 Locate the User ICO module on the upper right side of the cabinet. (See legend 2 in
General Cabinet ViewFigure 5-3, 9311 Macro V2 OD 2100 cabinet layout (p. 5-5).)
The following figure shows the front panel of the User ICO module.
....................................................................................................................................................................................................................................
8-164 Alcatel-Lucent Proprietary Alcatel-Lucent 9311 Macro V2 OD
Use pursuant to applicable agreements NN-20500-011 UA08.1
Issue 09.07 January 2013
9311 Macro V2 OD corrective maintenance procedures Replacing the User ICO module
Replacing the optional equipment
....................................................................................................................................................................................................................................
...................................................................................................................................................................................................
3 Power down the 9311 Macro OD. (See Powering down a 9311 Macro V2 OD (p. 7-2).)
...................................................................................................................................................................................................
4 On the DDU module, lift the protection cover (1) and disconnect the cable of the User
ICO supply (2) from the User ICO connector.
....................................................................................................................................................................................................................................
Alcatel-Lucent 9311 Macro V2 OD Alcatel-Lucent Proprietary 8-165
NN-20500-011 UA08.1 Use pursuant to applicable agreements
Issue 09.07 January 2013
9311 Macro V2 OD corrective maintenance procedures Replacing the User ICO module
Replacing the optional equipment
....................................................................................................................................................................................................................................
Figure 8-62 Disconnection of the User ICO supply cable from the DDU
...................................................................................................................................................................................................
6 On the User ICO module, disconnect the cables from the following connectors:
PWR User1, PWR User2, PWR User3, and PWR User4 connectors according to the
User Space used.
UMTS Alarm and User Alarm connectors using the flat blade screwdriver.
...................................................................................................................................................................................................
7 Unscrew the four screws from the User ICO using the Phillips screwdriver.
....................................................................................................................................................................................................................................
8-166 Alcatel-Lucent Proprietary Alcatel-Lucent 9311 Macro V2 OD
Use pursuant to applicable agreements NN-20500-011 UA08.1
Issue 09.07 January 2013
9311 Macro V2 OD corrective maintenance procedures Replacing the User ICO module
Replacing the optional equipment
....................................................................................................................................................................................................................................
...................................................................................................................................................................................................
9 Insert the new User ICO module by passing the supply cable of the module through the
hole.
...................................................................................................................................................................................................
10 Tighten the four screws using the Phillips screwdriver (tightening couple: 289 N.cm +/-
15%).
...................................................................................................................................................................................................
12 Check that all cables are correctly connected on the User ICO module.
...................................................................................................................................................................................................
13 Take the User ICO supply cable, lift the protection cover on the DDU module, plug the
User ICO supply to the User ICO connector, and put the protection cover back.
...................................................................................................................................................................................................
14 Power up the 9311 Macro OD. (See Powering up a 9311 Macro V2 OD (p. 7-4).)
...................................................................................................................................................................................................
....................................................................................................................................................................................................................................
Alcatel-Lucent 9311 Macro V2 OD Alcatel-Lucent Proprietary 8-167
NN-20500-011 UA08.1 Use pursuant to applicable agreements
Issue 09.07 January 2013
9311 Macro V2 OD corrective maintenance procedures Replacing the User ICO module
....................................................................................................................................................................................................................................
....................................................................................................................................................................................................................................
8-168 Alcatel-Lucent Proprietary Alcatel-Lucent 9311 Macro V2 OD
Use pursuant to applicable agreements NN-20500-011 UA08.1
Issue 09.07 January 2013
Appendix A: Product
conformance statements
Overview
Purpose
This appendix provides the 9311 Macro V2 OD product conformance statements.
Contents
...................................................................................................................................................................................................................................
Alcatel-Lucent 9311 Macro V2 OD Alcatel-Lucent Proprietary A-1
NN-20500-011 UA08.1 Use pursuant to applicable agreements
Issue 09.07 January 2013
Product conformance statements European regulatory requirement compliance
....................................................................................................................................................................................................................................
....................................................................................................................................................................................................................................
Compliance with the essential requirement of health requirement has been
demonstrated using EN50385.
....................................................................................................................................................................................................................................
Alcatel-Lucent 9311 Macro V2 OD Alcatel-Lucent Proprietary A-3
NN-20500-011 UA08.1 Use pursuant to applicable agreements
Issue 09.07 January 2013
Product conformance statements North American regulatory requirements compliance
....................................................................................................................................................................................................................................
Node B safety
The 9311 Macro V2 OD comply with UL60950-1 and CAN/CSA C22.2 No. 60950-01
Safety Standards. The CSA mark is applied on the Node B and demonstrates compliance
with both US and Canadian Standards.
....................................................................................................................................................................................................................................
A-4 Alcatel-Lucent Proprietary Alcatel-Lucent 9311 Macro V2 OD
Use pursuant to applicable agreements NN-20500-011 UA08.1
Issue 09.07 January 2013
Product conformance statements North American regulatory requirements compliance
....................................................................................................................................................................................................................................
On the top right of this equipment is a label that contains, among other information, a
product identifier in the following format:
US : U3EXDNANUMTSOUT for the 9311 Macro V2 OD equipped with iCCM2 or
xCCM.
US : AB6XDNANUMTSOUT for the 9311 Macro V2 OD equipped with CCM or
iCCM.
If requested, the following information must be provided to the telephone company:
ACTA Registered Number: U3E, AB6
Facility Interface Code (FIC): 04DU9.BN, 04DU9.DN, 04DU9.1KN, and
04DU9.1SN
Service Order Code (SOC): 6.0F
A FCC part 68 and ACTA compliant cable is provided with the Node B equipment, with
no connector at network interface side. The Node B equipment operates with a 1.544
Mbps digital channel. See Installation Instructions for details.
If the Node B equipment causes harm to the phone network, the telephone company will
notify you in advance that temporary discontinuance of service may be required. But if
advance notice is not practical, the telephone company will notify the customer as soon as
possible. Also, you will be advised of your right to file a complaint with the FCC if you
believe it is necessary
The telephone company may make changes to its facilities, equipment, operations or
procedures that could affect the operation of the equipment. If this happens the telephone
company will provide advance notice so you can make the necessary modifications to
maintain uninterrupted services.
If trouble is experienced with this equipment 9311 Macro V2 OD, for repair or warranty
information, please contact:
Hernan R. Noguchi Global
Product Compliance Laboratory (GPCL)
Alcatel-Lucent
Phone: 1-732-332-6002 101
Crawfords Corner Road Building
11C, Room 165 Holmdel NJ 07733-3030
If the equipment is causing harm to the telephone network, the telephone company may
request that you disconnect the equipment until the problem is resolved.
All repairs should be handled by authorized Alcatel-Lucent Service Personnel.
....................................................................................................................................................................................................................................
Alcatel-Lucent 9311 Macro V2 OD Alcatel-Lucent Proprietary A-5
NN-20500-011 UA08.1 Use pursuant to applicable agreements
Issue 09.07 January 2013
Product conformance statements North American regulatory requirements compliance
....................................................................................................................................................................................................................................
Node B data equipment
The following table shows which jacks are associated with which modes of operation.
Node B systems
Facility Interface Codes (FIC), Services Order Codes (SOC), USOC Jack Codes, and
Ringer Equivalence Number (REN) are shown in the table below for each port where
applicable.
For the 9311 Macro V2 OD equipped with CCM or iCCM:
....................................................................................................................................................................................................................................
A-6 Alcatel-Lucent Proprietary Alcatel-Lucent 9311 Macro V2 OD
Use pursuant to applicable agreements NN-20500-011 UA08.1
Issue 09.07 January 2013
Product conformance statements North American regulatory requirements compliance
....................................................................................................................................................................................................................................
Notes:
1. equipped with MDA 4E1/T1 PCM links
....................................................................................................................................................................................................................................
Alcatel-Lucent 9311 Macro V2 OD Alcatel-Lucent Proprietary A-7
NN-20500-011 UA08.1 Use pursuant to applicable agreements
Issue 09.07 January 2013
Product conformance statements Compliances for other regions/countries
....................................................................................................................................................................................................................................
....................................................................................................................................................................................................................................
A-8 Alcatel-Lucent Proprietary Alcatel-Lucent 9311 Macro V2 OD
Use pursuant to applicable agreements NN-20500-011 UA08.1
Issue 09.07 January 2013
Product conformance statements Operational conditions
....................................................................................................................................................................................................................................
Operational conditions
Overview
The aforementioned standards compliance of the products are based on the following
operating conditions (called normal operation):
Doors shall be closed and/or covers shall be in place.
External cables shall be of the same type as specified by Alcatel-Lucent.
No modification of any mechanical or electrical characteristics of the product shall be
made.
Any change or modification made to the product without written approval from
Alcatel-Lucent releases Alcatel-Lucent from subsequent responsibility regarding the
standards compliance.
....................................................................................................................................................................................................................................
Alcatel-Lucent 9311 Macro V2 OD Alcatel-Lucent Proprietary A-9
NN-20500-011 UA08.1 Use pursuant to applicable agreements
Issue 09.07 January 2013
Product conformance statements Cable specifications
....................................................................................................................................................................................................................................
Cable specifications
Overview
The compliance to the aforementioned standards has been verified using cables as
specified by Alcatel-Lucent. The continuing compliance of the product relies upon use of
the correct cabling scheme as well as use of identical type cables as specified by
Alcatel-Lucent. Refer to the installation guides for details on cable specifications.
....................................................................................................................................................................................................................................
A-10 Alcatel-Lucent Proprietary Alcatel-Lucent 9311 Macro V2 OD
Use pursuant to applicable agreements NN-20500-011 UA08.1
Issue 09.07 January 2013
Product conformance statements Product labelling
....................................................................................................................................................................................................................................
Product labelling
Overview
The label may be located inside or outside the product, provided that the operation and/or
maintenance personnel have the information when working on the product.
On the regulatory label, compliance to 47 CFR Part 15, 22 or 24, and 68 is stated along
with:
FCC ID, FCC Registration Number
Manufacturers name
Equipment designation
Nominal voltage operating range and maximum rated current.
Manufacturers name
Equipment designation
Nominal voltage operating range and maximum rated current
....................................................................................................................................................................................................................................
Alcatel-Lucent 9311 Macro V2 OD Alcatel-Lucent Proprietary A-11
NN-20500-011 UA08.1 Use pursuant to applicable agreements
Issue 09.07 January 2013
Product conformance statements Product labelling
....................................................................................................................................................................................................................................
Labelling for other regions/countries
Labelling for other regions and countries is performed as appropriate and required by the
local regulatory framework.
....................................................................................................................................................................................................................................
A-12 Alcatel-Lucent Proprietary Alcatel-Lucent 9311 Macro V2 OD
Use pursuant to applicable agreements NN-20500-011 UA08.1
Issue 09.07 January 2013
Index
iCCM-2 M MCPA
E eCEM
See: integrated Core Control See: Multi-Carrier Power
See: enhanced Channel
Module - 2nd generation Amplifier module
Element Module (eCEM)
(iCCM-2) See: Multi-Carrier Power
Amplifier module (MCPA)
....................................................................................................................................................................................................................................
Alcatel-Lucent 9311 Macro V2 OD Alcatel-Lucent Proprietary IN-1
NN-20500-011 UA08.1 Use pursuant to applicable agreements
Issue 09.07 January 2013
Index
....................................................................................................................................................................................................................................
Multi-Carrier Power Amplifier .............................................................
module
T Transceiver Module
front view, 8-65
front view, 8-28
Multi-Carrier Power Amplifier
module (MCPA) Transceiver Module (TRM)
............................................................. TRM
See: Transceiver Module
R replace See: Transceiver Module
(TRM)
Channel Element Module
(CEM), 8-4 .............................................................
SCPA
See: Single-Carrier Power
Amplifier module
See: Singlei-Carrier Power
Amplifier module (SCPA)
Single-Carrier Power Amplifier
module
front view, 8-67
Single-Carrier Power Amplifier
module (SCPA)
replace, 8-64
....................................................................................................................................................................................................................................
IN-2 Alcatel-Lucent Proprietary Alcatel-Lucent 9311 Macro V2 OD
Use pursuant to applicable agreements NN-20500-011 UA08.1
Issue 09.07 January 2013