Beruflich Dokumente
Kultur Dokumente
REPLACEMENT
1. REMOVE FRONT BUMPER COVER (See page 763)
E68351
I35261
E68352
RAIN SENSOR
660CT02
REPLACEMENT
1. REMOVE INNER REAR VIEW MIRROR STAY HOLDER COVER
3 Claws I35796
(b) Disengage the 2 claws and remove the rain sensor cover.
(c) Disconnect the connector.
2 Claws I35797
(d) Disengage the 2 claws and remove the rain sensor spring
cover.
2 Claws I35798
I35799
NOTICE:
Check if there is any SilGel, which of the rain sensor that has been removed, left on the wind-
shield glass and remove it if there is any.
Clean the dirt on the glass with a cloth etc.
When installing a new rain sensor, peel the transparent protective cap off the SilGel first.
Be careful not to let any air bubble in the rain sensor when installing it.
REPLACEMENT
1. REMOVE REAR WIPER ARM ASSY
(a) Remove the nut and the rear wiper arm.
2. REMOVE BACK DOOR TRIM BOARD ASSY (See page LIFTBACK 7540, WAGON 7545)
Liftback:
I35264
E58837
(c) Stop the rear wiper motor assy to the automatic stop posi-
Wagon: Defogger Line tion. Install the rear wiper arm to the position as shown in
the illustration.
Torque: 5.5 Nm (56 kgfcm, 49 in.lbf)
3050mm
(1.181.97 in.)
Liftback:
3050mm
(1.181.97 in.)
I35779
REPLACEMENT
E59361
(b) Insert the rear wiper rubber from the claw position of the
middle of the rear wiper blade into the end position.
(c) After passing the rear wiper rubber through the rear end
side claw, protrude it from the rear end stopper and pass
it through the front tip side claw.
E61233
E60706
ADJUSTMENT
1. REMOVE WASHER NOZZLE SUBASSY
(a) With the engine running, check that the point where the washer fluid hits the windshield and the rear
window is within the range indicated by the hatched line.
Front:
A
B
A
B
A
A
B
C C
E D
G F
I H
I35778
Rear (Wagon):
Rear (Liftback):
REPLACEMENT
I35256
8Clips I35257
I35258
E65848
E65849
(b) Remove the 2 torx bolts and the windshield wiper motor
assy.
E65850
E65850
(b) Scrape off the serration part of the wiper arm with a round
file or equivalent.
(c) Clean the wiper pivot serration with a wire brush.
Wiper Arm Serration
E58837
(d) Install the front wiper arm LH with the nut to the position
shown in the illustration.
Torque: 21 Nm (210 kgfcm, 15 ftlbf)
Cowl top ventilator louver HINT:
Hold down the arm hinge by hand to fasten the nut.
17.5 32.5 mm
(0.69 1.28 in.) I34455
(c) Install the front wiper arm RH with the nut to the position
shown in the illustration.
Torque: 21 Nm (210 kgfcm, 15 ftlbf)
HINT:
Cowl top ventilator louver
Hold down the arm hinge by hand to fasten the nut.
(d) Operate the wiper while running the water or the washer
fluid over the window, and check the wiping condition and
17.5 32.5 mm that the front wiper does not hit against the vehicle body.
(0.69 1.28 in.) I34456
REPLACEMENT
1. REMOVE STEERING COLUMN COVER LWR (See page 6527)
PRECAUTION
1. PRECAUTION OF WASHER NOZZLE ADJUSTMENT
(a) Do not clean or adjust the washer nozzle with a safety pin, etc. because;
(1) the washer nozzle tip is made of resin and could be damaged.
(2) adjustment is not necessary because the washer nozzle is a jet type.
(b) If the washer nozzle is clogged with wax etc., remove the objects and clean the nozzle hole with a soft
resin brush, etc.
Front wipers does not operate in HI 1. Windshield wiper switch assy 666
(Auto wiper system is normal). 2. Wire harness or connector
ONVEHICLE INSPECTION
E68115
E68116
Standard:
Tester connection Condition Specified voltage
1 (+B) Body ground Ignition switch OFF ON 0 10 to 14 V
2 (RSI) Body ground Rain sensor is covered by hand Signal waveform
4 (WF) Body ground Front washer switch OFF ON 10 to 14 V 0 V
Front wiper is in high speed operation
8 (+2) Body ground 10 to 14 V
(When front wiper switch is in AUTO position)
9 (F1) Body ground Front wiper switch OFF AUTO 10 to 14 V 0 V
11 (F2) Body ground Front wiper switch OFF AUTO 0 10 to 14 V
12 (WF) Body ground Front washer switch OFF ON 10 to 14 V 0 V
Front wiper is in 10 speed operation
16 (+1) Body ground 10 to 14 V
(when front wiper switch is in AUTO position)
17 (+S) Body ground Always Below 1 V
19 (SP) Body ground Ignition switch OFF ON 0 V 10 to 14 V
20 (VR1) Body ground Ignition switch OFF ON 0 V 10 to 14 V
22 (E) Body ground Always Below 1 V
23 (SG) Body ground Always Below 1 V
Ignition switch is ON and rain sensor adjust
24 (VP2) Body ground Signal waveform
switch is in (+) position () position
INSPECTION
7 (+1) 2 (EW)
Rain Sensor Adjust Switch (b) Rain Sensor Adjust Switch Operation Check
A (1) Check resistance between terminal of the terminal
B 12 (VR1) and the terminal 14 (VR2) when rain sen-
sor adjust switch is operated.
Switch position Resistance ()
C A position
D
B position 432 to 528
C position 216 to 264
E67353
D position 0
E68141
E67355
E68112
(b) w/ HID:
Inspect headlamp cleaner control relay operation
(1) Check that no continuity exists between the termi-
nal 2 and the terminal 5.
(2) Connect the positive (+) lead from the battery to the
terminal 1, and the negative () lead from the bat-
tery to the terminal 5.
(3) Connect the negative () lead from the battery to the
terminal 4, and check that continuity exists between
the terminal 2 and the terminal 5 for 0.7 to 0.9 se-
conds, then no continuity exists.
(4) Disconnect the positive (+) lead from the battery
from the terminal 1, and connect the positive (+)
lead from the battery to the terminal 1 again.
E69072
E68114
WIPER RUBBER LH
660CP01
REPLACEMENT
1. REMOVE FR WIPER BLADE LH
(a) Remove the front wiper blade LH from the front wiper arm LH.
NOTICE:
Do not fold down the front wiper arm with the front wiper blade being removed from it.
2. REMOVE WIPER RUBBER LH
(a) Remove the front wiper rubber LH from the front wiper blade.
(b) Remove the 2 wiper rubber backing plates from the wiper rubber LH.
E59361
(b) Install the wiper rubber LH so that the head part (Larger
side) of the wiper rubber faces the arm axle side.
NOTICE:
Push the front wiper blade into the grooves of the wiper
rubber to engage them completely.
E57398