Beruflich Dokumente
Kultur Dokumente
CUSTOMERS APPROVAL
CUSTOMER :
SIGNATURE: DATE:
APPROVED PM PD PREPARED
BY REVIEWED REVIEWED BY
T070800480-A5TMN-001
Rev:1.0
Revision History
2/26
T070800480-A5TMN-001
Rev:1.0
Table of Contents
No. Item Page
1. General Description.............................................................................................................................4
2. Module Parameter...............................................................................................................................4
3. Absolute Maximum Ratings.................................................................................................................4
4. DC Characteristics ..............................................................................................................................5
5. Backlight Characteristic.......................................................................................................................5
5.1. Backlight Characteristics ......................................................................................................... 5
5.2. Backlighting circuit................................................................................................................... 5
6. Optical Characteristics ........................................................................................................................6
6.1. Optical Characteristics............................................................................................................. 6
6.2. Definition of Response Time ................................................................................................... 6
6.3. Definition of Contrast Ratio ..................................................................................................... 7
6.4. Definition of Viewing Angles .................................................................................................... 7
6.5. Definition of Color Appearance................................................................................................ 8
6.6. Definition of Surface Luminance, Uniformity and Transmittance ............................................ 8
7. Block Diagram and Power Supply.......................................................................................................9
8. Interface Pins Definition ....................................................................................................................10
9. Timing Characteristics .......................................................................................................................12
9.1. AC Electrical Characteristics ................................................................................................. 12
9.2. Input Clock and Data Timing Diagram................................................................................... 12
9.3. Timing.................................................................................................................................... 13
9.4. Data Input Format.................................................................................................................. 14
9.5. Power Sequence ................................................................................................................... 15
10. Quality Assurance .............................................................................................................................16
10.1 Purpose ................................................................................................................................. 16
10.2 Standard for Quality Test ....................................................................................................... 16
10.3 Nonconforming Analysis & Disposition.................................................................................. 16
10.4 Agreement Items ................................................................................................................... 16
10.5 Standard of the Product Visual Inspection ............................................................................ 16
10.6 Inspection Specification......................................................................................................... 17
10.7 Classification of Defects ........................................................................................................ 21
10.8 Identification/marking criteria................................................................................................. 21
10.9 Packing.................................................................................................................................. 21
11. Reliability Specification......................................................................................................................22
12. Precautions and Warranty.................................................................................................................23
12.1 Safety ....................................................................................................................................... 23
12.2 Handling ................................................................................................................................... 23
12.3 Storage ..................................................................................................................................... 23
12.4 Metal Pin (Apply to Products with Metal Pins) ......................................................................... 23
12.5 Operation............................................................................................................................... 24
12.6 Static Electricity ..................................................................................................................... 24
12.7 Limited Warranty.................................................................................................................... 24
13. Packaging..........................................................................................................................................25
14. Outline Drawing.................................................................................................................................26
3/26
T070800480-A5TMN-001
Rev:1.0
1. General Description
The specification is a transmissive type color active matrix liquid crystal display (LCD) which uses
amorphous thin film transistor (TFT) as switching devices. This product is composed of a TFT-LCD panel,
driver ICs and a backlight unit.
2. Module Parameter
VSS=0V, Ta=25C
Item Symbol Min. Max. Unit
Supply Voltage VCC -0.3 5.0 V
Storage temperature TSTG -30 85 C
Operating temperature TOP -30 85 C
Note 1: If Ta below 50C, the maximal humidity is 90%RH, if Ta over 50C, absolute humidity should be
less than 60%RH.
Note 2: The response time will be extremely slow when the operating temperature is around -10, and
the back ground will become darker at high temperature operating.
4/26
T070800480-A5TMN-001
Rev:1.0
4. DC Characteristics
5. Backlight Characteristic
5/26
T070800480-A5TMN-001
Rev:1.0
6. Optical Characteristics
viewing angle
Contrast ratio(See 6.3) CR 400 500 -
X =Y =0
Response time TR - 10 20
ms
(See 6.2) TF - 15 30
XR - TBD -
Red
YR - TBD -
XG - TBD -
Chromaticity Green
YG - TBD -
Transmissive
XB - TBD -
(See 6.5) Blue
YB - TBD -
XW 0.26 0.31 0.36
White
YW 0.28 0.33 0.38
Horizont X+ 60 70 -
Viewing
al X- 60 70 -
Angle Center CR10 Deg.
Y+ 40 50 -
(See 6.4) Vertical
Y- 60 70 -
100%
90%
10%
0%
Tr Tf
Tr is the time it takes to change form non-selected stage with relative luminance 10%
to selected state with relative luminance 90%;
Tf is the time it takes to change from selected state with relative luminance 90% to
non-selected state with relative luminance 10%.
Note : Measuring machine: LCD-5100
6/26
T070800480-A5TMN-001
Rev:1.0
100%
90%
10%
0%
Tr Tf
Tr is the time it takes to change form non-selected stage with relative luminance 90%
to selected state with relative luminance 10%;
Tf is the time it takes to change from selected state with relative luminance 10% to
non-selected state with relative luminance 90%;
Note : Measuring machine: LCD-5100 or EQUI
6.3. Definition of Contrast Ratio
Contrast is measured perpendicular to display surface in reflective and transmissive mode.
The measurement condition is:
Measuring Equipment Eldim or Equivalent
Measuring Point Diameter 3mm//1mm
Measuring Point Location Active Area centre point
A: All Pixels white
Test pattern
B: All Pixel black
Contrast setting Maximum
Definitions: CR (Contrast) = Luminance of White Pixel / Luminance of Black Pixel
6.4. Definition of Viewing Angles
7/26
T070800480-A5TMN-001
Rev:1.0
X
X/6 X/3 X/3 X/6
Display Area
Y/6
1 2 3
Y/3
Y
4 5 6
Y/3
7 8 9
Y/6
8/26
T070800480-A5TMN-001
Rev:1.0
LCD Panel
R[0:7] G[0:7] B[0:7]
Data bus
RESETHSVSDCLKDE
U/DL/RMODEDITHB
Control
Source + Gate
Driver Signal input
7.0 inch
800(RGB)*480
FPC
DVDDGNDVGH
VGLAVDDVCOM
Power
LEDA LEDK
BLU
BLU
9/26
T070800480-A5TMN-001
Rev:1.0
10/26
T070800480-A5TMN-001
Rev:1.0
Note 6:Global reset pin.Active low to enter reset state.Suggest to connect with an RC reset circuit for
stability.Normally pull high.
Note7 :Dithering function enable control,normally pull high.
When DITHB=1,Disable internal dithering function,
When DITHB=0,Enable internal dithering function.`
11/26
T070800480-A5TMN-001
Rev:1.0
9. Timing Characteristics
9.1. AC Electrical Characteristics
12/26
T070800480-A5TMN-001
Rev:1.0
9.3. Timing
13/26
T070800480-A5TMN-001
Rev:1.0
14/26
T070800480-A5TMN-001
Rev:1.0
15/26
T070800480-A5TMN-001
Rev:1.0
10.1 Purpose
This standard for Quality Assurance assures the quality of LCD module products supplied to
customer.
16/26
T070800480-A5TMN-001
Rev:1.0
Eye Eye
45 45
A zone
B zone
Area
Acc. Qty
Black / White spot Size
a
Foreign material 0.20 Ignore
(Round type) 0.20<0.50 N3
01 Pinholes 0.50< 0
Stain
b
Particles inside cell.
(Minor defect) = ( a + b) /2
17/26
T070800480-A5TMN-001
Rev:1.0
L
Black and White line L
Scratch
03 Foreign material
(Line type)
(Minor defect) Length Width Acc. Qty
/ W 0.1 Ignore
L 2.5 0.1 W 0.2 3
L2.5 0.2 W 0
Total 3
Glass Crack
04
(Minor defect)
18/26
T070800480-A5TMN-001
Rev:1.0
Glass Burr:
(Minor defect)
19/26
T070800480-A5TMN-001
Rev:1.0
FPC Defect:
(Minor defect)
10.1 Dent, pinhole width a<w/3.
a
(w: circuitry width.)
10 w
10.2 Open circuit is unacceptable.
10.3 No oxidation, contamination and distortion.
a
20/26
T070800480-A5TMN-001
Rev:1.0
Note1:Bright dot is defined as the defective area of the dot is larger than 50% of one sub-pixelarea.
Bright dot:The bright dot size defect at black display pattern.It can be recognized by 2% transparency of
filter when the distance between eyes and panel is 350mm50mm.
Dark dot:Cyan,Magenta or Yellow dot size defect at white display pattern.It can be recognized by 5%
transparency of filter when the distance between eyes and panel is 350mm50mm.
21/26
T070800480-A5TMN-001
Rev:1.0
22/26
T070800480-A5TMN-001
Rev:1.0
12.1 Safety
12.1.1 The liquid crystal in the LCD is poisonous. Do not put it in your mouth. If the liquid
crystal touches your skin or clothes, wash it off immediately using soap and water.
12.1.2 Since the liquid crystal cells are made of glass, do not apply strong impact on them.
Handle with care.
12.2 Handling
12.2.1 Reverse and use within ratings in order to keep performance and prevent damage.
12.2.2 Do not wipe the polarizer with dry cloth, as it might cause scratch. If the surface of the
LCD needs to be cleaned, wipe it swiftly with cotton or other soft cloth soaked with petroleum
IPA, do not use other chemicals.
12.3 Storage
12.3.1 Do not store the LCD module beyond the specified temperature ranges.
23/26
T070800480-A5TMN-001
Rev:1.0
12.5 Operation
12.6.1 CMOS LSIs are equipped in this unit, so care must be taken to avoid the
electro-static charge, by ground human body, etc.
12.6.2 The normal static prevention measures should be observed for work clothes and
benches.
12.6.3 The module should be kept into anti-static bags or other containers resistant to
static for storage.
12.7.1 Our warranty liability is limited to repair and/or replacement. We will not be responsible
for any consequential loss.
12.7.2 If possible, we suggest customer to use up all modules in six months. If the module
storage time over twelve months, we suggest that recheck it before the module be used
.
24/26
T070800480-A5TMN-001
Rev:1.0
13. Packaging
TBD
25/26
1 2 3 4 5 6
REV SFWJTJPO!SFDPSE TJHO EBUF
A First Issue SJH 13/09/20
PIN FUNCTION
164.90.3
PIN SYMBOL
2.71 156.70.3/BEZEL OPENING
1 LEDA
3.92 154.08/A.A 5.70.3 2 LEDA
A (80.96) A
3 LEDK
4 LEDK
RGB
5 GND
6 VCOM
7 DVDD
8 MODE
9 DE
14. Outline Drawing
7.0" 10 VS
800RGB*480
11 HS
Display Center 12 B7
85.92/A.A
1000.3
13 B6
(80)
14 B5
15 B4
(61)
89.10.3/BEZEL OPENING
16 B3
52.26
17 B2
(28)
18 B1
(23)
19 B0
B 20 G7
B
9.3
21 G6
7.33
22 G5
23 G4
24 G3
25 G2
26 G1
27 G0
26/26
80.150.5
28 R7
29 R6
Contact side
Stiffener
30 R5
50.5
3.80.3
31 R4
32 R3
1 50
33 R2
C 0.30.05
34 R1
80.950.5 35 R0
36 GND C
37 DCLK
38 GND
39 L/R
40 U/D
41 VGH
DETAIL:4/1 50 NC
D K D
VERSION DATE MODEL
B 2013.09.20 NAME: T070800480-A5TMN-001
SCALE NO. UNIT TITLE:
A 202 Outline
APPROVED CHECKED DRAWN FILE NAME:
Rev:1.0
T070800480-A5TMN-001
1 2 3 4 5 6