Beruflich Dokumente
Kultur Dokumente
Version 3.8
Q1
Which two statements describe the purpose of the technology prefix? (Choose two.)
Q2
Which statement is true about only out-of-band signaling?
Q3
Examine the example output.
hostname GW1
!
B. gateway
Q4
Refer to the exhibit. Which two actions would be initiated by a UAS? (Choose two.)
A. Contacts the user when a SIP invitation is received
C. Returns a response on behalf of the user to the invitation originator
Q5
Which option is true concerning the MGCP call agent?
Q6
Which statement best describes gatekeeper operation when the technology prefix is matched and the
gatekeeper is using the technology prefix with hopoff?
A. The gatekeeper always forwards the call to the zone specified in the hopoff command.
Q7
Refer to the exhibit. All IP phones are SCCP phones. Phone D makes an internal call to phone G.
Which call setup signaling statement is true?
E. Phone D signals the call agent. The call agent processes the call and signals phone G.
Q8
Refer to the exhibit. All IP phones use SCCP. Fax machine F calls fax machine J. Which call setup
signaling statement is correct?
E. Gateway A processes the call and signals gateway B. Gateway B processes the call. During the setup,
the gateways query the gatekeeper for address resolution and call setup permission.
Q9
Refer to the exhibit. Three department managers share the directory number 3000. The Marketing
manager's phone is attached to port 1/1. The Engineering manager's phone is attached to port 1/2. The
Shipping manager's phone is attached to port 1/3. In which situation would an incoming call ring on the
Shipping manager's phone?
E. The Engineering manager and Marketing manager are on the phone.
Q10
DRAG DROP
Using Cisco Unified Communications Manager Express, what four steps are necessary to implement
COR? (Choose four.)
Answer:
Q11
At what point does the MGCP call agent release the setup of the call path to the residential gateways?
D. After the call agent has sent a connection request to both the source and destination and has relayed
a modify-connection request to the source so that the source and destination can set up the call path
Q12
Which two codes together make up the number that follows the E.164 recommendation numbering
scheme? (Choose two.)
A. Country code
B. Subscriber code
Q13
When using CUBE, which two statements describe how media flow-through differs from media
flow-around? (Choose two.)
E. Media flow-around terminates the signaling stream and allows RTP streams to flow directly between
endpoints.
F. Media flow-through provides address hiding by terminating both signaling and RTP streams.
Q14
HOTSPOT
Refer to the exhibit. The Acme Corp. uses H.323 to place calls to their supplier RR Industries. Acme also
has a voice connection to an ITSP for long distance over a SIP network. Which
configuration should Acme use to deploy the CUBE?
Answer:
Q15
Which two are types of Call Admission Control? (Choose two.)
A. Local
C. Resource-based
Q16
Using a standalone IOS gateway, which three steps are necessary to implement COR? (Choose three.)
Q17
Refer to the exhibit. You have configured a gatekeeper and an IP-IP gateway on the same router. When
you look at the output from the show gatekeeper endpoint command, the IP-IP gateway is not registered
with the gatekeeper. What needs to be configured to resolve this issue?
B. You need to add a VoIP dial peer to the configuration.
Q18
Which process changes an internal extension into a fully qualified external PSTN number before
matching to a dial peer?
C. Number expansion
Q19
The SJ local zone contains a gatekeeper that controls two gateways, SJ1 and SJ2. Both gateways
provide access to area code 408. Which two command strings should be entered into the gatekeeper to
give the SJ2 gateway priority over the SJ1 gateway? (Choose two.)
Answer: A,D
Q20
Which command parameter specifies that the router should not attempt to initiate a trunk connection but
should wait for an incoming call before establishing the trunk?
E. connection-trunk 404555....answer-mode
Q21
HOTSPOT
Refer to the exhibit. Choose the correct configuration command set that will allow the gateway in zone BR
to register with the gatekeeper at HQ so that the gateway is placed in zone BR.
Q22
C. A telephone system that responds to a caller with a voice menu and helps to appropriately connect the
call
Q23
You have been asked to deploy a gatekeeper to support CUBE that will connect your organizational
domain to the domain of an Internet Telephony Service Provider so that callers can reach the 407 area
code. Which configuration will support this function?
A.
Q24
What is the E.164 standard?
Q25
You have set up a complex dial plan using translation rules. The following translation rule has been
configured. What output would correspond to the test translation-rule command?
translation-rule 1
rule 0 ^0.. 215550210
rule 1 ^1.. 215550211
rule 2 ^2.. 215550212
rule 3 ^3.. 215550213
rule 4 ^4.. 215550214
rule 5 ^5.. 215550215
rule 6 ^6.. 215550216
rule 7 ^7.. 215550217
rule 8 ^8.. 215550218
rule 9 ^9.. 215550210
Q26
A customer needs to configure a CAS E & M circuit that will support inbound and outbound DNIS and
inbound ANI. Which configuration will accomplish this task?
Q27
To hide its identity when initiating calls, Phone B requests that Server B place its calls for it. What kind of
device is Server B?
A. Proxy
Q28
Which dial-peer command can set the parameters that search through a series of dial peers for a
destination that is not in use?
A. Hunt
Q29
Refer to the H.323 message in the exhibit. What is the gateway doing with the gatekeeper?
C. Lightweight registration
Q30
A customer wants to roll out IP telephony to the regional office. They are currently using the G.711 codec
at headquarters. Which codec will support voice activity detection and comfort noise generation?
C. G.729B
Q31
DRAG DROP
Which three services are supported by CUBE when supporting H323-to-SIP calls? (Choose three.)
Answer:
Q32
Refer to the exhibit. Which message ID can be used to track this call from the requesting endpoint?
A. 8204
Answer: A
Q33
Refer to the exhibit. Which dial peer configuration will block phone A from making long distance calls?
1
A. A
B. B
C. C
D. D
E. E
Answer: A,E
Q34
Refer to the exhibit. What is the minimum WAN bandwidth required to support three simultaneous VoIP
calls in this network?
C. 79,200 bps
Q35
Where would you assign COR lists in Cisco Unified Communications Manager Express?
B. ephone-dn
Q36
B. Sends both the technology prefix and zone prefix to the remote gatekeeper
Q37
Which CUBE configuration will support H.323 protocol interworking and address hiding?
Q38
Which statement is true about MGCP?
D. Call agents order and direct each step of call completion for the endpoints.
Q39
A telemarketing firm needs to use number translation for incoming and outgoing calls. They have defined
two translation profiles, one for incoming and one for outgoing calls. What can be used to simplify this
task?
D. Trunk group
Q40
Refer to the exhibit. Your customer has connected an existing PBX to the IP network. The PBX users can
make calls to other extensions on the PBX but are unable to call the test extension 2201. All other
applications on the IP network are working correctly. Compare the PBX system requirements to the
configuration for R1 in the exhibit. Which configuration change will resolve the problem?
B. RTP
Q43
A new business in Great Britain needs to have a PSTN connection that will handle a maximum of 30
inbound and outbound calls at any given time. The customer only has one slot available on the
designated PSTN router. Which digital line type should be recommended?
C. ISDN E1 PRI
Q44
Refer to the exhibit. When extension 201-555-1000 dials 404-555-1200, how are the digits manipulated in
R1 so that they are presented correctly at R2?
A. The outbound VoIP dial peer is matched and all digits are sent.
Q45
Refer to the exhibit. The Carmichael caller dials the site access code for Merrimack (6) followed by the
four-digit extension number of the destination phone (0124). If the call is going to go across the IP WAN,
which action will have to be taken?
B. Strip the site access code and send four digits.
Q46
Refer to the exhibit. You have a client that is testing a directory gatekeeper in the lab to provide address
resolution between two different zones. Two of the commands in the running-config output are incorrect.
Which two changes will correct the configuration? (Choose two.)
A. replace
zone prefix GK-A 770 . . . . . . .
with
zone prefix GK-A 770 . . . .
B. replace
zone prefix GK-B 404 . . . .
with
zone prefix GK-B 404 . . . . . . .
C. replace
zone local DGK acme.com
with
zone remote DGK acme.com
D. replace
zone local GK-A acme.com 172.16.14.44 1719
with
zone remote GK-A acme.com 172.16.14.44 1719
1
E. replace
zone remote GK-B acme.com 172.16.14.99 1719
with
zone local GK-B acme.com 172.16.14.99 1719
Answer: A,D
Q47
Refer to the exhibit. All IP phones use SCCP. Phone D calls phone G.
Which statement is true about the audio path?
Q48
Refer to the exhibit.
Your customers dial in to your company using a local number, and their calls cross the WAN to an IVR
system. They are complaining that the IVR system does not always accept their input or may get it wrong.
The IVR system has been checked and is working properly. What needs to be added to the dial peer on
the incoming H.323 gateway to correct this problem?
D. dtmf-relay h245-alphanumeric
Q49
What is the best description of an MGCP endpoint?
Q50
In North America, which E&M signaling type is used most often for geographically separated equipment?
B. Type II
Q51
Which three are supervisory signals? (Choose three.)
B. On hook
C. Off hook
E. Ring
Q52
Refer to the exhibit. Select the recommended QoS configuration for the LAN segments of the network in
the campus and branch office.
Q53
The D channel in ISDN is an example of which two signaling methods? (Choose two.)
B. CCS
E. Out-of-band
Q54
Refer to the exhibit. Which configuration option will allow communication between a voiceenabled router
and a PBX?
A. voice port 1/0/0
signalingwink-start
operation 4-wire
auto-cut-through
type 1
B. voice port 1/0/0
signalingimmediate-start
operation 4-wire
type 5
C. voice port 1/0/0
signaling delay-start
auto-cut-through
operation 4-wire
type 3
6
Q55
Which dial plan characteristic shows the most obvious improvement by dropping a number translation
step?
B. Post-dial delay
Q56
Refer to the exhibit. Users are not able to complete a call from 678-555-1212 to 770-555-1111.
What is the correct diagnosis for the problem?
Q57
What is the most common E&M type used outside North America?
E. Type V
Q58
Site A uses three-digit internal numbers and remote Site B uses four-digit internal numbers. All calls to
the PSTN are routed through Site B. What dial plan below best represents provision simplicity, assuming
the NANP numbering plan?
Q59
Refer to the exhibit. Enzo's Bikes manufactures high end bicycle frames. Until recently they sold only to
bicycle shops; however, now they are starting to sell to end users. They need a way to add two additional
sales staff and ensure that the senior sales technician always gets the first call. Drew is the senior sales
technician. Bob is the newest sales technician. Bob's phone should always be the last one chosen for
incoming sales calls, after Drew and James. Bob's phone should be chosen first only when Drew and
James are busy on calls.
destination-pattern 5555110
preference 0
C. dial-peer voice 3 pots
destination-pattern 5555110
preference firstlast
D. dial-peer voice 3 pots
destination-pattern 5555110
preference 3
huntstop
E. dial-peer voice 3 pots
destination-pattern 5555110
preference high
Answer: A
Q60
Refer to the exhibit. You have been asked to configure a dial peer on R2 that will match only the
extensions of the four telephones attached. Which dial-peer statement will you use?
Q61
When setting up a VoIP call, what is the first thing a gateway router tries to match to a dialed number?
D. Destination pattern
Q62
Refer to the IOS configuration in the exhibit. How will the next incoming call be routed?
E. The call will be routed to the next available channel, starting from channel 24, hunting down toward
channel 1.
Q63
Identify the VoIP network component that provides CAC, bandwidth control and management, and
address translation.
B. Gatekeeper
Q64
Technology prefix is a discriminator which is used for distinguishing between gateways having specific
capabilities within a given zone. Which two descriptions are true about the purpose of the technology
prefix? (Choose two.)
Q65
Which two of the following signaling protocols are peer-to-peer protocols? (Choose 2.)
A. H.323
C. SIP
Q66
For the following options, which statement best describes only out-of-band signaling?
B. IP
D. UDP
E. RTP
Answer: B,D,E
Q68
The partial configuration of a Cisco device of the Company is shown as follows: Which command will
restore communication with gatekeeper functionality to this device on the basis of the example output?
B. gateway
Q69
Which of the following best describes a function of RTCP?
B. Increase bandwidth.
D. Fragment data packets.
E. Prioritize voice packets.
Q71
For the following options, which one is correct about the MGCP call agent?
Q72
Which two of the following VoIP gateway platforms are considered to be Integrated Services Routers
(ISRs)? (Choose 2.)
Q73
In a Cisco UCM single-site deployment, what is the maximum number of IP phones that can register with
a UCM cluster?
D. 30,000
Q74
As a network technician for the Company, you are responsible for designing and maintaining VoIP
network. The VoIP network topology of the Company is displayed as follows: On the basis of the exhibit
presented. All IP phones are SCCP phones. Phone D makes an internal call to phone G.
Which call setup signaling statement is correct?
E. Phone D signals the call agent. The call agent processes the call and signals phone G.
Q75
In a Cisco UCM multisite WAN with centralized call-processing deployment model, what redundancy
feature should be configured on remote site routers to provide basic IP telephony services in the event of
a WAN outage?
B. SRST
Q76
Which four of the following are Cisco-supported IP telephony deployment models? (Choose 4.)
A. Single site
C. Multisite with centralized call processing
D. Clustering over the IP WAN
E. Multisite with distributed call processing
Q77
Identify two gateway supplementary services. (Choose 2.)
A. Hold
C. Transfer
Q78
According to the G.114 recommendation, the maximum one-way delay for voice should ideally not
exceed how much delay?
B. 150 ms
Q79
On the basis of the related knowledge, at which point does the MGCP call agent release the setup of the
call path to the residential gateways?
D. After the call agent has sent a connection request to both the source and destination and has relayed
a modify-connection request to the source so that the source and destination can set up the call path
Q80
Identify the preferred voice quality measurement approach for VoIP networks.
B. PESQ
Q81
HOTSPOT
Hotspot
Answer:
Q82
Which method of fax relay uses a store-and-forward approach?
B. T.37
Q83
When using CUBE, which two statements are true about how media flow-through differs from media
flow-around? (Choose two.)
C. Media flow-around terminates the signaling stream and allows RTP streams to flow directly between
endpoints.
D. Media flow-through provides address hiding by terminating both signaling and RTP streams.
Q84
What codec is required for fax pass-through and/or modem pass-through?
A. G.711
Q85
Identify three quality issues that can result because of a lack of network bandwidth.(Choose 3.)
A. Jitter
C. Delay
D. Packet loss
Answer: A,C,D
Q86
Hotspot
Call Admission Control (CAC) is a concept that applies to voice traffic only-not data traffic. Which
two types are of Call Admission Control? (Choose two).
A. Resource-based
C. Local
Q87
What protocol is used to communicate between a DSP farm configured on an IOS router and a Cisco
Unified Communications Manager server?
D. SCCP
Q88
When using a standalone IOS gateway, which three steps are necessary to implement COR?
Q89
What is the Layer 2 overhead (in bytes) for Frame Relay traffic?
C. 6 bytes
Q90
As a Companynetwork technician, you are responsible for establishing and maintaining VoIP network.
You have configured a gatekeeper and an IP-IP gateway on the same router. When you examine the
output from the show gatekeeper endpoint command, the IP-IP gateway is not registered with the
gatekeeper. What needs to be configured to resolve this issue?
Q91
Which three factors must be considered when calculating the total bandwidth of a VoIP call? (Choose 3.)
A. Codec size
C. Data-link overhead
D. Sample size
Q92
Observe the following options, which process changes an internal extension into a fully qualified external
PSTN number before matching to a dial peer?
C. Number expansion
Q93
The acronym CNG was used to refer to two different concepts in this chapter. One was the calling tone
used when sending a fax, used to identify a call as a fax call. What is the other purpose of CNG (that is,
not dealing with fax calls)?
Q94
Hotspot
The SJ local zone contains a gatekeeper that controls two gateways, SJ1 and SJ2. Both gateways
provide access to area code 408. For the following command strings, which tow will be entered into the
gatekeeper to give the SJ2 gateway priority over the SJ1 gateway? (Choose two.)
Answer: A,D
Q95
Which of the following media resources require DSPs (that is, the resource cannot be performed by Cisco
Unified Communications Manager)?
C. Transcoding
Q96
If a client picked up a customer service handset and was automatically connected to a customer service
representative without dialing any digits, what kind of call would it be?
D. PLAR call
Q97
Which configuration parameter would you change to set the dial tone, busy tone, and ringback tone on an
FXS port?
A. Cptone
Q98
What is the default (and most commonly used) method of access signaling used on E&M voice ports?
B. Wink-start
Q99
Which situation most likely requires changes to the FXS port default settings?
Q100
Hotspot
What is the E.164 standard?
Q102
When an end-to-end call is established across a VoIP network, how many inbound call legs are
associated with the call?
B. Two
Q103
A POTS dial peer performs which of the following two functions? (Choose 2.)
Q104
When configuring a VoIP dial peer, which command is used to specify the address of the terminating
router or gateway?
C. Session target
Q105
A dial peer, also known as an addressable call endpoint, is a device that can originate or receive a call in
a telephone network. Which dial-peer command can set the parameters that search through a series of
dial peers for a destination that is not in use?
A. Hunt
Q106
What happens if there is no matching dial peer for an outbound call?
Q107
The H.323 message is displayed as follows: On the basis of this information, What is the gateway doing
with the gatekeeper?
C. Lightweight registration
Q108
Which dial-peer configuration command attempts to match the calling number (that is, the ANI string)?
C. Answer-address
Q109
T1 CAS uses ___________________ signaling.
C. Robbed-bit
Q110
A. ISDN
C. E1
D. T1
Q111
A. 8204
Q112
The _____________ command is used to configure a T1 controller for CAS.
C. ds0-group
Q113
DRAG DROP
Q114
ISDN uses ______ for Layer 2 signaling, which is defined in _______.
B. LAPD, Q.921
Q115
The two types of ISDN interfaces are ______ and ______.
B. PRI, BRI
Q116
When you use the show gatekeeper endpoints command on the gatekeeper, a Cisco UBE router will be
displayed as a(n) __________ type.
C. H323-GW
Q117
Which two are QSIG supplemental services or additional network features? (Choose 2.)
A. Path replacement
B. Do not disturb
Q118
Which two tasks are performed by the RAS signaling function of H.225.0? (Choose 2.)
Q119
What are the functions of an H.323 gateway?
Answer: D
Q120
The exhibit below shows partial VoIP network topology of the company :
Based on the exhibit presented, which protocol provides the necessary sequence numbers so that voice
packets originating at R1 are played in the correct order at R5?
B. RTP
Q121
Which RAS message does a gateway use to request admission to a network and to also request phone
number to IP address resolution?
A. ARQ
Q122
DRAG DROP
Click and drag the type of call on the above to the type of voice port it applies to on the below.
Q123
Use the __________________ command to designate a source IP address for a voice gateway.
Q124
On the basis of the exhibit.
When extension 201-555-1000 dials 404-555-1200, how are the digits manipulated in R1 so that they are
presented correctly at R2?
A. The outbound VoIP dial peer is matched and all digits are sent.
Q125
Which call control model does MGCP use?
B. Centralized
Q126
How do you configure a router to use MGCP on a digital port?
Q128
Identify four SIP servers. (Choose 4.)
A. Registrar
C. Redirect
D. Location
E. Proxy
Q129
What is one way to implement call coverage?
B. Pilot numbers
Q130
Examine the following items carefully. The D channel in ISDN is an example of which two signaling
methods? (Choose two.)
B. out-of-band
E. CCS
Which of the following are characteristics of a scalable dial plan? (Choose 3.)
A. Fault tolerance
C. Hierarchical numbering plan
D. Dial-plan logic distribution
Q132
Which dial plan characteristic shows the most obvious improvement by ropping a number translation
step?
B. Post-dial delay
Q133
Which of the following best describes a numbering plan?
Q134
Partial CompanyVoIP network topology and the configuration information of R1 and R2 are displayed as
follows:
On the basis of the exhibit. Users are not able to complete a call from 678-555-1212 to 770-555- 1111.
Which diagnosis is correct for this problem?
Q135
Which of the challenges associated with integration requires translations?
Answer: D
Q136
Hotspot
For the following items, which is the most common E&M type used outside North America?
E. Type V
Q137
Which worldwide prefix scheme was developed by the ITU to standardize numbering plans?
A. E.164
Q138
D. Number normalization
Q139
Which of the following best describes the ALI?
Q140
By default, _________ dial peers strip any outbound digits that explicitly match their destination pattern.
C. POTS
Q141
Which item correctly describes the relationships between the feature and the category it belongs?
A. Gateway -1 and 2
CUBE-3 and 4
Q142
Which digit manipulation option is applied globally?
A. Number expansion
Q143
As a Cisco engineer, you work for the Company. When setting up a VoIP call, what is the first thing a
gateway router tries to match to a dialed number?
D. Destination pattern
Q144
Select a rule that would search and replace a ten-digit number with the internal 2XXX extension.
Q145
In Cisco IOS, which of the following is associated to each dial peer?
A. Call leg
Q146
Hotspot
A new business in Great Britain needs to have a PSTN connection that will handle a maximum of 30
inbound and outbound calls at any given time. The customer only has one slot available on the
designated PSTN router. Which digital line type will you recommend?
C. ISDN El PRl
Q147
One best practice is to create a default POTS dial peer with the direct-inward-dial attribute using the __
wildcard as the destination pattern.
D. .
Q148
Partial CompanyVoIP network topology and the configuration information on Gateway-A are displayed
below:
D. D
Q149
___________________ is an easy way to overcome the problem of overlapping directory numbers.
A. Site-code dialing
Q150
Instead of only routing intersite calls over an IP WAN link, __________ also uses the IP WAN link for
PSTN calls.
C. TEHO
Q151
Which of the following is defined to include a number of members that were previously defined?
D. corlist
Q152
In Unified CME, corlists are directly assigned to what?
B. ephone-dn
Q153
Which command is used to display corlists and members?
Q154
Which of the following RAS messages can be sent using either unicast or multicast?
C. GRQ
Q155
B. Admission control
C. Address resolution
D. Bandwidth control
E. Zone management
Q156
What H.323 gatekeeper feature allows calls to be routed to a specific zone, regardless of the zone prefix
in the address?
Q157
Identify two methods of LRQ forwarding. (Choose 2.)
B. LRQ blast
D. LRQ sequential
Answer: B,D
Q158
Given the following configuration, what IP address will GK1 use to send and receive RAS messages?
B. 172.16.0.2
Q159
What VoIP dial-peer configuration mode command can be used to specify a technology prefix of 2#,
indicating that when the dial peer is used as an outgoing dial peer, a 2# will be prepended to the dial
string sent to the gatekeeper?
D. tech-prefix 2#
Q160
An H.323 gatekeeper maintains a separate gateway list, ordered by priority, for each of its zone prefixes.
If a gateway does not have an assigned priority for a zone prefix, what priority does it use as a default?
B. 5
Q161
How much bandwidth does an H.323 gatekeeper assume will be required by a G.729 call?
B. 16 kbps
Q162
What parameter of the bandwidth command, used in gatekeeper configuration mode, specifies the
maximum amount of bandwidth that can be allocated in a zone?
B. Total
Q163
Where should RAI be configured?
B. On a gateway
Q164
Cisco UBE features include __________________, ________________, codec filtering, and video
interworking. (Choose 2.)
B. Address hiding
C. Protocol interworking
Q165
Protocol interworking interconnects VoIP networks, using the same or different __________ protocols.
A. Signaling
Q166
Media streams can _______________ or ____________ a Cisco UBE.
D. flow-through, flow-around
Q167
If codec filtering is not required, a Cisco UBE router also supports ____________ codec negotiations.
D. Transparent
Q168
When deploying Cisco UBE and RSVP-based CAC, ensure the flows that should utilize RSVP are
configured for media _______________.
C. flow-through
Q169
When interworking H.323 and SIP, the configuration applied with the allowconnections command is
_________________.
C. Unidirectional
Q170
Choose the correct command to enable H.323 to H.323 interworking.
Q171
Use the ________________ command to configure codec pass-through.
B. codec transparent
Q172
A gatekeeper should be configured to route calls between local zones via a Cisco UBE gateway.
How can this be achieved?
B. The gatekeeper should route calls via a local zone that contains a Cisco UBE gateway.
Q173
DRAG DROP
Assume a SIP voice network. Drag each characteristic to the type of SIP call setup the characteristics
best describes.
Q174
The following are the original dial peer configurations for routers R1 and R2 :
R1 :
dial-peer voice 20 voip
destination-pattern 408.......
session target ipv4: 192.168.2.254
!
R2
dial-peer voice 21 ports
destination-pattern 4085554321
port 1/0/1
!
Which phones can call to the other?
Q175
How are inbound and outbound call legs handled from the perspective of the source router?
D. The inbound call leg is matched first. Then, once the destination is known, an outbound call leg is
established.
Q176
You are the Voice technician at Certkiller.com. The certways network uses VoIP. Your newly appointed
certways trainee wants to know what the modes of the playout delay buffer are. What will your reply be?
Q177
You are the network technician at Certkiller.com. Your newly appointed certways trainee wants to know
what factors affects audio quality. What will your reply be?
Q178
When a call is placed, it is routed toward the destination. Which call legs are created on that router for the
call?
Q179
Which of the following best describes the main difference between G.729 and G.729a?
Q181
What is used to translate called (DNIS) and calling automatic number identification (ANI) numbers before
routing the call?
D. Translation Pattern
Q182
What could happen if the playout delay buffer size is configured too large?
Q183
You are the network engineer at Certkiller.com. certways has its headquarters in New York and a branch
office in Delaware. In the branch office, one VoIP dial-peer has been configured to point to headquarters
over a low speed serial link. You want to limit the maximum number of concurrent calls to 3. Which
command would you use?
Q184
What happens if no incoming dial peer matches a router or gateway?
Q185
If a PC connected to an IP Phone is having trouble obtaining an IP address, which setting on the phone
might help resolve the problem?
D. Forwarding Delay
Q186
You have all ten digits being sent to your CM from the PSTN (via a gateway). If you have four digit
extensions, how do you make sure that the call gets routed?
Q187
Which of the following statements is correct when discussing how the Cisco CallManager works with IP
Phone registration?
Q188
Which statement is true about VoIP packet loss?
Q190
Which channel carries Q.931 signals in a T1 connection from a PBX to a Cisco gateway?
C. 24
Q191
What is true about H.323 endpoint call setup?
Q192
What is used in the Cisco implementation of T.37?
Q193
What is the optimal end-to-end delay that should be achieved in a VoIP network?
C. 150 ms
Q194
What is the E.164 numbering plan?
Q195
What type of signalling is used for a circuit transmitted within the same channel as the voice?
Q196
You are the Voice technician at Certkiller.com. The certways network uses VoIP. Your newly ppointed
certways trainee wants to know what the disadvantage of using VoIP rather than VoFR or VoATM are.
What will your reply be?
Q197
You have a pair of voice enabled routers that have the capability of supporting only medium complexity
codecs. You need to conserve bandwidth on WAN links without major impact to call quality. Which
codecs will satisfy these requirements? (Choose two)
B. G.729A
D. G.729.AB
Q198
What is the most important piece to implement if you are considering a VoIP infrastructure?
A. QoS
Q199
What explains how the Cisco IP SoftPhone uses the Cisco CallManager?
B. Cisco IP SoftPhone uses the services of the Cisco CallManager to route calls through an IP telephony
network.
Q200
Which are three required steps in digitizing voice? (Choose three)
Q201
Your manager asks you for a worksheet defining items that need to be addressed forthe future VOIP and
IP telephone rollout. What items do you put on the worksheet that need to be addresses for the wiring
closets? (Choose all that apply.)
Q202
From the list below, what allows a Cisco IP phone to detect the absence of audio and therefore does not
transmit packets over the network?
Q203
When analyzing the WAN for IP Telephone deployment, you need to collect information from the WAN
and LAN devices. You need to determine current Bandwidth usage before rolling out a solution. From the
analysis you are performing, there are categories you can collect information from. Select two from the list
below.
A. Device information, which includes router models, memory, CPU, interface card modules versions and
software versions
C. The existing WAN topology, which includes logical design information and bandwidth subscription
rates
Q204
Which preference key word assigns top precedence to a dial peer in a hunt-group?
A. 0
Q205
What are two basic parameters needed to setup a dial peer connected to the PSTN?(Choose two)
A. Voice port
D. Destination pattern
Q206
Which field can be manually entered into the database when using the BAT tool, but not when using the
TAPS tool?
Q207
Name two factors that will need to be considered and may provide a hurdle to move forward with your
VOIP rollout and IP telephony implementation:
Q208
You're a CCNP certified employee at Deutsche Telekom. You are working with the abc .com Telephone
Company, in Rammstein Germany, to assist them to set up a simple configuration to demonstrate an
FXS-to-PSTN connection across an IP network. The Ethernet interfaces and routing protocols are already
configured on both routers. The R1 router will act as gateway to the PSTN to the PSTN and is correctly
configured for this task. You are required to add the voice portion to the R2 router. Configure the pots and
VoIP dial peers and insure that the pots telephone on the R2 router can reach the PSTN connected to the
R1 router. The analog telephone is
connected to voice port 1/0/0. The customer uses the access code 9 to dial out the PSTN. Insure that the
R1 and R2 recognize the dialed digits as standard E.164 numbers. The telephone number of the pots
telephone connected to the R1 router is 49648455554321. After the configuration is complete you may
click on the telephone to check your configuration. If the call is successful, you will get a ringing message
and a completed call. If the call is unsuccessful, you will get a busy signal. The R1 router has the
following configured ports: Ethernet: 0/0 172.16.1.11 255.255.255.0 To configure the router click on a
host icon that is connected to a router by a serial console cable.
Explanation:
en
config t
dial-peervoice 1 pots
destination-pattern 6495551212
port1/0/0
dial-peervoice 2 voip
destination-pattern +9T
sessiontarget ipv4:172.16.1.11
Answer:
Q209
In a distributed call processing model, which three are located at each site? (Choose three.)
B. Voice messaging
C. Media resources
D. Cisco CallManager cluster
Q210
What can be used not only to restrict dialing, but also to identify a subset of a subset of a wildcard pattern
(when using the @ wildcard in the North American Dialing Plan)?
C. A Route Filter
Q211
You are the Voice technician at Certkiller.com. Your newly appointed certways trainee wants to know
what types of trunks Cisco support with the connection trunk command. What will your reply be?
Q212
hostname R1
!
interface serial0/0
ip address 172.16.1.1 255.255.255.248
!
controller t1
framing esp
clock source line
linecode b8zs
Your customer has forwarded this diagram and configuration. The customer wishes to have a connection
between its PBXs, a connection that is created and dropped as required. There is one configuration
statement missing from each router. What are the two missing statements? (Choose two)
Q213
Choose all functions available to you with the IP SoftPhone. (Choose all that apply.)
Answer: B,C,E,F
Q214
You are the network engineer at Certkiller.com. You have configured dial peers in a hunt group for a
Support team that answers when the number 5952215 is dialled. The Support team consists of one
senior agent and three junior agents. You want the senior agent to receive the incoming call first. Which
dial peer should you configure to point to the senior agent?
Q215
With Cisco CallManager Release 3.0, the term "route point" is replaced with which term from the list
below?
C. Route list
Q216
For very low-speed links (those with a link speed of less than 768 K), it is necessary to use techniques
that provide link fragmentation and interleaving of packets. This prevents voice traffic from being delayed
behind large data frames and hence bounds jitter. What are two techniques that exist for this?
Q217
You are the network engineer at Certkiller.com. You have configured real-time call control processing on
the certways VoIP network. You want to verify this configuration. What command should you use?
Q218
You are the network engineer at Certkiller.com. certways has been using the following dial peer codec
command:
Codec g729r8
Q219
What are two characteristics of a distributed call processing model? (Choose two.)
Q220
Cisco is making every effort to ensure that the gateways, applications, and client produced integrate and
operate seamlessly with third party products. From the list below, select which protocols are being used to
ensure this effort.
D. All choices are correct.
Q221
When discussing Route Groups, we know that they control specific devices such as gateways. On which
protocols can gateways be based?
A. H.323
B. MGCP
D. Skinny Gateway Protocol
Q222
You are the network engineer at Certkiller.com. Your newly appointed certways trainee wants to know
how an endpoint determines the address of the gatekeeper. What will your reply be? (Choose two.)
Q223
You are the Voice engineer at Certkiller.com. certways has an H.323 gatekeeper. Your newly appointed
certways trainee wants to know what functions are supported by this gatekeeper. What will your reply be?
(Choose four.)
Q224
You are the network engineer at Certkiller.com. The certways network is shown in the following exhibit:
If the show gatekeeper calls command shows a total of five active calls on the gatekeeper, how many call
legs would the show call active voice command display on GatewayA?
D. 10
Q225
You are the Voice technician at Certkiller.com. Your newly appointed certways trainee wants to know
what makes it possible for gatekeepers to communicate with each other. What will your reply be?
B. RAS channel
Q226
Your newly appointed certways trainee wants to know what protocol negotiates the codec type for
B. H.225
Q227
You are the network engineer at Certkiller.com. certways has its offices in London.You are installing a
voice gateway. What do you need to verify? (Choose two.)
Q228
You are the network engineer at Certkiller.com. Your newly appointed certways trainee wants to know
what a voice gateway is. What will your reply be?
Q229
What would Receiving an Alarm Indication Signal of Blue indicate on your T1 connection where your
voice traffic is going over?
D. Blue means there is an alarm occurring on the line upstream from the equipment that is connected to
the port
Q230
You are the network technician at Certkiller.com. Your newly appointed certways trainee wants to know
when glare occurs. What will your reply be?
D. When both ends of a telephone line or trunk are seized by different users.
Q231
One voice packet is lost between Phone A and Phone B. What will be the result to the listener?
C. The listener will hear the audio normally.
Packet loss concealment will make the loss inaudible.
Q232
What will happen when a network link is oversubscribed?
Q233
Your newly appointed certways trainee wants to know what CAC applies to. What will your reply be?
C. Voice traffic
Q234
You are the network engineer at Certkiller.com. certways has its headquarters in New York and a branch
office in New Hamshire. You want to configure a permanent connection between the PBX at
headquarters and the PBX at the branch office. The following configuration is used at the New York site:
dial-peer voice 20 pots
destination-pattern 20
port 1.0:1
dial-peer voice 41 voip
destination-pattern 41
session target ipv4:10.2.0.20
The following configuration is used at the New Hamshire site:
dial-peervoice 40 pots
destination-pattern 41
port 1/0:1
dial-peer voice 20 voip
destination-pattern 20
session target ipv4:10.4.1.41
What must be added to the voice port configuration at the New York site?
B. Connection trunk 41
Q235
You are the Voice technician at Certkiller.com. Your newly appointed certways trainee wants to know
what configuration would define a destination pattern for all of the 1000 and 2000 range of extensions
starting with the numbers 555. What will your reply be?
C. 555[1-2]...
Q236
certways distributes computer components and has warehouses in New York and Chicago. Headquarters
is located in Washington, DC. To keep costs low, all inside sales associates are located at headquarters.
Your want to provide a direct analog telephone connection to the inside sales teams from the pick-up
counters at the warehouses. This connection should not require the inside sales teams to dial any digits.
One of the warehouses is having a problem with their sales phone. You receive the following output:
altwhse#show voice port 1/0:1
Foreign Exchange Office
Type of VoicePort is E M
Operation State is DORMANT
Administrative State is UP
The Last Interface Down Failure Cause is Administrative Shutdown
Description is not set
Noise Regeneration is enabled
Non Linear Processing is enabled
Music On Hold Threshold is Set to -38 dBm
In Gain is Set to 0 dB
Out Attenuation is Set to 0 dB
Echo Cancellation is enabled
Echo Cancel Coverage is set to 8 ms
Connection Mode is plar
Connection Number is 2000
Initial Time Out is set to 10 s
Interdigit Time Out is set to 10 s
Call-Disconnect Time Out is set to 60 s
Q237
You are the network engineer at Certkiller.com. Your newly appointed certways trainee wants to know
which features render VAD ineffective. What will your reply be? (Choose two.)
A. Fax
D. Music on hold
Q238
How do a-law and mu-law reduce quantization error?
Q239
What is a logical grouping of directory numbers (DN) and route patterns with similar reachability
characteristics when working with IP Telephony?
D. A Partition
Q240
What unlocks the 7960 configuration menu?
B. **#
Q241
Name two standards that are being adopted from by the telecommunicates industry that are used to
communicate between applications such as the Cisco CallManager providing IP PBX functionality and
unified products such as the GateServer products acquired through the acquisition of AmtevA. (Select
two.)
Q242
Which network protocols does an IP Phone use to communicate?
C. TCP/IP for skinny signalling and UDP/IP for RTP voice streams.
Q243
There are six major steps for WAN deployment when preparing IP telephony. From the list below, please
select which of the following are valid pre deployment choices.(Choose all that apply.)
Q244
Before voice and video can be placed on a network, it is necessary to ensure that adequate bandwidth
exists for all required applications. To begin, the minimum bandwidth requirements for each major
application (for example, the voice media streams, video streams, voice control protocols, and all data
traffic) should be summed. This sum represents the minimum bandwidth requirement for any given link,
and it should consume no more than what percentage of the total bandwidth available on that link?
D. 75%
Q245
You need to prefix any outbound number dialled by a user with a 9. Where can you do this? (Choose
two.)
B. On a Route Pattern
C. On a Translation Pattern
Q246
Your Manager asks you as the Lead Network Designer to give a status on the VOIP integration project.
Your Manager specifically asks what you need to replace the PBX. From the list below, what are you
going to need to replace the PBX to roll out the VOIP solution? (Choose all that apply.)
A. TCP/IP
B. Cisco CallManager
D. IP Telephones
F. Cat 4000's
Q247
What is the major advantage of designing and placing VoIP and Internet telephony in a clients
organization?
Q248
You are the network technician at Certkiller.com. Your newly appointed certways trainee wants to know
what function T-CCS performs. What will your reply be?
D. It allows a PBX to pass proprietary signalling to another PBX across the IP network.
Q249
You are the network engineer at Certkiller.com. You to connect a Cisco voice gateway to a PBX or the
PSTN via ISDN (PRI, QSIG, BRI). What are two attributes of the PBX/PSTN switch that must be known to
understand which features to configure on the voice gateway to connect successfully to it? (Choose two)
Q250
You are working with a potential customer that would like to integrate its existing PBX telephone system
into its IP network. The accompanying figure shows that the customer has two offices that need to be
connected to the IP network so that the customer can exchange telephone calls without using the PSTN.
Both PBXs are currently connected to T1 ISDN circuits. Which signaling type will allow you to support
your customer?
A. QSIG
Q251
Which statement is an example of in-band signaling?
Q252
You are the network technician at Certkiller.com. VoIP is implemented on the certways network. Your
newly appointed certways trainee wants to know what this implementation uses to carry the payload
across the network. What will your reply be?
B. 2 bytes
Q254
What does the PBX use to determine the destination of a call?
Q255
Which of the following is the worst-case compression delay for CD-ACELP?
D. 20 ms
Q256
What type of connection is considered a call leg?
C. A logical connection
Q257
To which layer of the OSI model does Q.921 signaling equates to in ISDN?
D. Data-Link
Q258
certways has a PBX at corporate HQ and one at a branch office. You to replace the PBX-to-PXB TDM
trunk connection with IP connectivity. The PBXs use proprietary signalling method. The following is a
partial configuration of the HQ router that connect to the PBX:
controller t1 1/0
ds0-group 1 timeslots 1-24 type ext-sig
dial-peer voice 1 voip
destination-pattern 1001
session target ipv4:10.10.0.1
dial-peer voice 2 pots
destination-pattern 2001
port 1/0:1
connection trunk 1001
Which command is missing from the above configuration?
Q259
You are the network engineer at Certkiller.com. The certways ISDN network has two PBX systems from
different manufactures. Which protocol allows functionality between these two PBX systems?
A. QSIG
Q260
You are the network technician at Certkiller.com. Your newly appointed certways trainee wants to know
which application conveys fax using T.37 fax relay. What will your reply be?
D. SMTP
Q261
certways sells managed IP Phone service to businesses in multi-tenant units. certways has POPs in
many cities, so all of their dial peer patterns are based on 10 digit numbers. Users dial 9 for local calls,
followed by the 7 digital local number. The following dial peer has been configured in a New York POP:
dial-peer voice 595 pots
destination-pattern 595
port 1/0:24
A user dials a local number, 9-638-4422.
What command must be configured in the gateway to allow the call to complete?
D. num-exp 9.......595.......
Q262
IP Telephony uses which protocol that does not accommodate re-transmission?
Q263
When placing a call from an IP Phone to another IP Phone, how is ringback generated?
Q264
What is the most probable cause of jitter?
A. Variable delay
Q265
When an IP phone says "Configuration CM List", what is it doing?
Q266
Name two sensitivities that Voice traffic has that data traffic is not necessarily affected by.
C. Delay
D. Jitter
Q267
You are the network technician at Certkiller.com. Your newly appointed certways trainee wants to know
what does the connection tie-line command emulates. What will your reply be?
Q268
Your customer would like to investigate converging voice and data on their existing T1 Frame Relay WAN
link between R1 and R2. The following applications are consuming no more bandwidth than what is in the
list on this segment of the network. T1 link 1536 Kbps e-mail 75 Kbps Internet 200 Kbps Oracle 500 Kbps
FTP 250 Kbps Total 1025 Kbps The customer has allocated 25% of the WAN link for routing updated and
other overhead. Assuming 6 bytes overhead for Frame Relay, no cRTP and using the G.729 codec, how
many calls could be placed on this link?
C. 4 calls
Q269
You have set up Call Admission Control for a customer between their headquarters and manufacturing
facility over their Frame Relay WAN. You are using the G.726r16 codec with a 40 byte sample, CRTP
without CRC, and 90 kbps configured as the maximum bandwidth for CAC to use. What will happen when
7 calls try to call the remote office?
B. Only 4 calls will go through and the remainder will get a reorder tone.
Q270
You have designed a complex dial plan using digit manipulation. Given the following snippet of your
configuration file, what action would you expect to result when a call beginning with the digits "5501" is
received?
dial-peer voice 1 pots
destination-pattern 5501... ...
prefix
port 1/0/0
Q271
You are the network technician at Certkiller.com. VoIP is implemented on the certways network Your
newly appointed certways trainee wants to know what is used to carry VoIP voice packets on this
network. What will your reply be?
C. RTP/UDP
Q272
You are the network technician at Certkiller.com. Your newly appointed certways trainee wants to know
what TCP's reliable deliver service provides. What will your reply be?
B. Flow control, sequenced delivery, automatic error recovery, and transmission window management
Q273
You are the Voice technician at certways , Inc. You want to deploy an IP telephony solution for the
company. The certways network is currently a traditional LAN/WAN based on Frame Relay. Your CEO
has read about the issues of converging both data and voice traffic onto a single network. She is
concerned about the quality of their calls that need to cross the WAN in particularly. What would you need
to implement to ensure QoS for VoIP over Frame Relay?
C. Fragmentation, traffic shaping, priority queuing, Low Latency Queuing, and link efficiency with cRTP.
Q274
You are the network engineer at Certkiller.com. Your newly appointed certways trainee wants to know
which functions use UDP as their transport mechanism. What will your reply be? (Choose two)
A. RTP
B. RAS control function
Q275
What does gateway require to function as a translating gateway?
B. The ability to recognize the call control procedures of both connecting endpoints.
Q276
You are the Voice engineer at Certkiller.com. Your newly appointed certways trainee wants to know what
compressed RTP does. What will your reply be?
Q277
You are the network engineer at Certkiller.com. You are implementing Frame Relay traffic shaping on the
certways network. Your newly appointed certways trainee wants to know why Frame Relay traffic shaping
is important. What will your reply be?
D. It ensures that excess traffic above the CIR on the link is not dropped, but is buffered and sent when
there is capacity on the link.
Q278
You are the network engineer at Certkiller.com. You want to verify the registration of the gateway with the
call agent. Which show command should you use?
A. show mgcp
Q279
What identifies an MGCP endpoint?
D. A two part identifier that consists of the local name of the user and the domain name of the gateway.
Q280
Q281
Given the SIP network shown in the diagram identify which three actions are initiated by the UAC (user
agent client)? (Choose three)
Q282
Which characteristic is true about SIP protocol messages?
B. Text-based
Q283
Upon which protocol model is the SIP protocol based?
D. HTPP/WWW
Q284
Which type of signaling is DTMF?
D. Address
Q285
With regard to SIP and SDP, which of the following statements is true?
Q286
You are the network engineer at Certkiller.com. You are configuring a connection to a SIP proxy server.
Which command would you use to specify the IP address of the server?
A. sip-ua
sip-server ipv4:1.2.3.4
Q287
Which of the following call control models are based on decentralized call control? (Choose two.)
A. SIP
C. H.323
Q288
How is CAS different on E1 and T1?
Q289
In the connection between a Cisco router and an E M port on a PBX, which side is generally the Cisco
side?
D. Signaling unit
Q290
You are the network technician at Certkiller.com. Your newly appointed certways trainee wants to know
which signal types are used by E M. What will your reply be?
Q291
In an effort to consume less bandwidth across the WAN, the decision was made at certways to change
the voice packet size. They changed from two voice frames per packet to one voice frame per packet.
What effect did this have on certways 's voice traffic?
Q292
You have been forwarded some questions by a prospective VoIP customer who would like to know the
Cisco default sample size for the G.729 codec. What is it?
D. 10 ms
Q293
You are the network engineer at Certkiller.com. certways has its headquarters in New York and branch
offices in Delaware, Detroit and Denver. certways has a traditional time-division multiplexing (TDM) based
network with automated call distribution (ACD) private branch
exchanges (PBX) and desktop systems. You want to add an IP telephony solution to the certways
network. What will enable server and agent-level IP telephony to coexist with the existing network?
A. IPCC
Q294
What component can be used to compensate for jitter?
Q295
You are the network engineer at Certkiller.com. certways has an IP network. Your newly appointed
certways trainee wants to know which issues would adversely affect voice quality on the certways
network. What will your reply be?
Q296
In accordance with the G.114 standard, which of the following delay ranges is acceptable?
A. 0 - 150 ms
Q297
Which application allows you to communicate to multiple remote offices simultaneously?
Q298
Which of the following is the correct formula for encoding PCM?
D. 4000 Hz frequency sampled at two times the frequency and each sample is represented in 8 bits = 64
kbps
Q299
Your newly appointed certways trainee wants to know what CAC applies to. What will your reply be?
C. Voice traffic
Q300
D. Separation of queues, queue scheduling, and marking control and management traffic
Q301
Which tool can be applied to the Campus Switches to help eliminate traffic congestion?
D. QoS
Q302
You are the Lead Network Engineer for your company. Your manager asks what needs to be upgraded
on the Network to begin Preparing for the VOIP upgrade. Your Network Campus Consists of One Core
Rack of Cat 4000 Switches and 4 closets with BayStack and Synoptics hubs. IP phones will be placed on
every desk of the organization and the entire Campus is wired with Cat 5e. From the list below, what
needs to be done? (Choose one.)
D. Upgrade all the Hubbed gear with Cat 4000 series Switches
Q303
Which of the following QoS measures affect the outbound queue when implemented? (Choose three.)
A. LLQ
C. WFQ
D. CBWFQ
Answer: A,C,D
Q304
You are using class-based weighted fair queuing (CBWFQ) to manage queues in your network Voice
quality has been inconsistent over lower speed WAN links and users have been complaining. You have
decided to configure low latency queuing (LLQ) on the lower speed links to help improve voice quality in
the network. Which three of the following steps should you take to implement LLQ in the network?
(Choose three)
Q305
You are the network engineer at Certkiller.com. certways is using LLQ on the serial interface 3/3 on the
certways router. You want to verify the status if LLQ on the interface. Which command would you use?
Q306
On what is traffic engineering for voice based?
C. Grade of service.
Q307
Given the network shown in the exhibit, select the recommended QoS configuration for the slow speed
WAN segment connecting the campus and branch office.
A. LLQ Voice traffic marked as EF Voice control traffic marked as AF31 Implement Admission Control
Q308
Considering only the delays actually shown in the exhibit, how will the proposed network meet the
Answer: A
Q309
Examine the following PBX system parameters: The calling side seizes the line by going off-hook on its
E-lead and sends information as DTMF digits. The voice path is 4-wires, and the voice enabled router is
in another building from the PBX. Select the correct set of commands to allow communication between a
voice enabled router and a PBX.
Q310
Which device is used to allow an H.323 stream to transit a firewall?
C. Proxy
Q311
Refer to the graphic for IP addresses and telephone numbers. You are working with a customer that is
opening a small sales office in R2. You would like to be able to have the user in R2 be able to dial into the
PBX in R1 over the IP WAN. The R1 PBX uses loop start, a two-wire operation, and DTMF dialing.
Please choose the correct FXO port configuration for R1.
operation 2-wire
dial-type dtmf
Q312
Which problem does a-law and mu-law address?
Q313
Which will provide your IP Phones with an IP Address?
Q314
If the Cisco SIP server shown in the exhibit is used only for SIP redirect call setup, which two types of
operating environments can be used for the server? (Choose two.)
A. Linux (Redhat)
C. Solaris
Q315
A network has the following characteristics:
* the use of the G.711 codec with codec speed of 64kbps
* a 160-byte sample size
* the use of Frame Relay without compressed Real-Time Transport Protocol (CRTP)
* FRF.12 with 6 bytes of overhead
What minimum WAN bandwidth would be required to support three simultaneous VoIP calls?
A. 247200 bps
Q316
What is the purpose of RTCP?
Q317
What is the approximate frequency range of human speech?
C. 200 Hz to 9000 Hz
Q318
Exhibit:
The illustration above shows the timing and order of arrival of voice packets at the end device. Each voice
packet contains 20 ms of voice datA. Assuming a play-out buffer of 20 ms, what will happen to voice
packet number 3?
C. It will be dropped and treated as a lost packet.
Q319
In T1 CAS, where are the signaling states and control features carried for Super Frame robbedbit
signaling?
Q320
What is the process of assigning audio amplitude to a unique digital code word?
D. Quantization
Q321
Refer to the exhibit. Lighthorse Equine Management would like to investigate converging voice and data
on their existing T1 Frame Relay WAN link between R1 and R2. Currently the following lists ofapplications
are consuming no more bandwidth than what is listed on this segment of the network.
The customer has allocated 25% of the WAN link for routing updates and other overhead. They would like
to increase the number of samples encapsulated in each PDU to 40 ms. You have calculated 6 bytes of
overhead for Frame Relay, no cRTP,and the use of the G.711 codec. How many simultaneous calls could
be placed on this link?
B. 1 call
Q322
Which organization approved the H.323 standard?
D. ITU
Q323
When they are booted, the Cisco Access Digital Trunk Gateway DT-24+, the Cisco Access Digital Trunk
Gateway DE-30+, and the Catalyst 6000 digital gateway are provisioned with Cisco CallManager location
information. When these gateways initialize, a list of Cisco CallManager's, referred to as a
______________ is downloaded to the gateways.
D. Cisco CallManager redundancy group
Q324
You are the VoIP engineer at Certkiller.com. A certways user complains that she gets a busy tone instead
of a dial tone when she tries to call another user. You want to troubleshoot this problem.
What command should you use?
Q325
Which device listed below has an intelligent power management system that grants or denies power to
various system components based on power availability in the system for use with IP telephony?
Q326
What Cisco Catalyst Switch command produces the following inline power output? Defalut Inline Power
allocation per port: 10.00 Watts (0.23 Amps @42V) Port InlinePowered PowerAllocated
Admin Oper Detected mWatt mA @42V
---- ---- ---- ---- ----
7/1 auto off no 0 0
7/2 auto on yes 5040 120
7/3 auto faulty yes 12600 300
7/4 auto deny yes 0 0
7/5 off off no 0 0
Q327
Recently, the group of the certways network designers have been deploying a new network. The
customer needs to configure a CAS E M circuit that will support inbound and outbound DNIS and inbound
ANI. Which configuration will accomplish this task?
Q328
What are two constraints that you may encounter when trying to design a IP Telephone infrastructure?
Q329
What is the biggest issue affecting voice transport when you implement IPSec VPNs in a converged
network?
C. Throughput considerations.
Q330
What factors must be considered in the overall design when implementing an IPSec VPN for transport of
voice?
D. Port numbers and added overhead.
Q331
What will be the outcome of an incoming VoIP call arriving at CK2 from CK1, given the following router
configurations?
CK1 Configuration
dial-peer voice 1 pots
destination-pattern 1111
port 1/0/0
CK2 Configuration
dial-peer voice 1 pots
destination-pattern 2222
port 1/0/0
!
dial-peer voice 2 voip
destination-pattern 1111
session-target ipv4:172.16.1.1
Q332
Use the exhibit to answer the following questions.
When a call is placed from extension 1001 to 555-2212, which outbound dial peer is matched?
Q333
You are the network engineer at Certkiller.com. certways has its headquarters in New York and branch
offices in Delaware, Detroit and Denver. You have deployed VoIP over the certways WAN. certways user
at headquarters complain that early in the day, the quality of calls between headquarters and the branch
offices is very good, but as the day progresses and more calls are placed to the branch offices, the quality
degrades. The certways network is using RSVP. The WAN bandwidth to the branch offices allows 4 calls
to the Delaware office, 6 calls to the Detroit office, and 8 calls to the Denver office. You want to verify the
configuration of Call Admission Control on the headquarters router. What command should you use?
Q334
On the MOS scale, what does a 5 represent?
D. Excellent
Q335
certways has its headquarters in New York and branch offices in Delaware, Detroit and Denver.Each
office has an analog phone at each location. These phones are connected to an FXS port on the on-site
router. The Finance department at the Denver office is unable to make any phone class from these
analog phones. You receive the following output:
Q336
Which type of delay is caused by the line speed of the interface?
B. Serialization delay
Q337
What is the key element in call admission control when interconnecting CallManager sites via the IP
WAN?
A. Gatekeepers
Q338
What does the Digit Discard Instruction of PreDot do to the pattern 9.2148134444?
Q339
What from the list below combines voice mail, e-mail, and fax into a single application suite where a
single application can be used to store and retrieve entire suite of message types?
D. Unified messaging
Q340
Which gateway interface connects to the standard station port of a PBX?
D. FXO
Q341
A 9 digit number must be dialed to reach numbers on the PSTN. What process makes sure that the first 9
digit is not transmitted as part of the called number?
C. Digit manipulation
Q342
You are the network technician at Certkiller.com. Your newly appointed certways trainee wants to know
what the attributes of a scalable dialing plan are. What will your reply be? (Choose four)
A. Logic distribution
B. Hierarchical design
C. Simplicity in provisioning
E. reduction in post-dial delay
Q343
Which file does the BAT tool use to import users into the CallManager database?
A. CSV
Q344
When the Directories button on the 7960 phone is pressed, what does the 7960 use to retrieve the
Dirctory information?
A. XML
Q345
Which two tools are most appropriate for configuring 4,000 IP Phones prior to deploying the phones and
allow phones to auto register? (Choose two.)?
B. BAT
D. TAPS
Q346
When does an IP Phone receive the ring tones on the phone?
Q347
DRAG DROP
Drag each of the dial peers on the left to the phone number that it would match on the right.
Q348
DRAG DROP
Drop
Q349
DRAG DROP
Drop
nswer:
Q350
Refer to the exhibit. Your customer wants to converge the existing PBX network with the IP network. The
three remote offices have various types of PBXs. The customer is using a combination of tie-lines and
trunks to connect the PBXs today. Which kind of connection should be implemented to allow calls to be
placed from 201-555-1000 to 727-555-1000 so that when the call is completed, network resources are
returned for other uses?
C. tie-line
Q351
Refer to the exhibit. A QoS strategy has already been deployed on the LAN. Choose three WAN QoS
best practices that should be used over the WAN link. (Choose three.)
Q352
Refer to the exhibit. Highland Park Property Development is integrating a Cisco Unified Communications
Manager Express system with the existing PBX via an E1 QSIG trunk. After the initial configuration, no
calls can be placed from IP phones to PBX phones. How can this problem be resolved?
B. trunk groups
Q354
Which mechanism do you use to implement calling privileges on Cisco Unified Communications Manager
Express?
D. COR
Q355
In which three RAS messages is the technology prefix sent? (Choose three.)
A. GRQ
B. RRQ
E. IRQ
Q356
Refer to the exhibit. The Acme Corp. is deploying a CUBE. As a component of protocol interworking
between RR Industries and the ITSP, they need to configure at least two dial peers. When the IP WAN is
functional, Acme Corp. wants to use 5-digit dialing to RR Industries. Which three dial peers will complete
the configuration for Acme Corp.? (Choose three.)
Answer: B,C,F
Q357
Which two are attributes of SCCP? (Choose two.)
A. It is Cisco proprietary.
C. It is classified as client/server architecture.
Q358
Which command specifies the ISDN switch type as PRI?
Q359
Which command would you use to display information about the ISDN PRI interface?
C. show controllers