Sie sind auf Seite 1von 3

CO shift conversionFor additional generation

of hydrogen in synthesis gas the CO shift


conversion is applied downstream of other
syngas generation processes of hydrocarbon
feedstocks.
At the outlet of steam reformers, partial oxidation reactors or coke oven gas units the syngas
contains H2, CO, CO2, CH4 and water in chemical equilibrium at high temperatures in the range
of 700 to 1400 C depending on the process pressure and the mixture of feed stock and process
steam or water.

By means of the CO shift conversion an important portion of the CO content in the cracked gas
is used for additional hydrogen generation, which is following the chemical reaction

CO + H2O <=> H2 + CO2

This process is exothermic and is limited by the chemical equilibrium.

There are three different versions of CO shift conversion:

High temperature (HT) CO shift conversion at about 300 to 450 C down to approx. 2.5
% CO on dry basis at the reactor outlet
Medium temperature (MT) CO shift conversion or so-called isothermal shift conversion
at about 220 to 270 C down to approx. 0.5 % CO on dry basis at the reactor outlet.
Low temperature (LT) CO shift conversion at about 180 to 250 C down to approx. 0.2 %
CO on dry basis at the reactor outlet

For every process a special catalyst will be used in a fixed bed reactor to get maximum yield of
H2 product.

The use of HT CO shift conversion is state of the art in almost every hydrogen plant.

The application of the low temperature CO shift conversion is normally installed downstream of
the HT shift at already reduced CO content in the feed gas.

The additional investment is considered for plants having a capacity above approx. 40,000 Nm/h
H2 product. The catalyst of the LT shift is very sensitive against sulphur, chlorine and liquid
water and special attention is required during start up and plant upset conditions.

In former concepts the LT shift was important because of the downstream methanisation of CO
following the CO2 removal unit, to meet the product purity at minimum H2 losses. After the
implementation of the Pressure Swing Adsorption (PSA unit) for H2 purification these process
steps have become obsolete.

The MT CO shift conversion as isothermal reaction can be approximated in several adiabatic


reactors with intercoolers or better in an isothermal reactor with integrated steam generation for
cooling of the process gas. The temperature of the shift reaction is controlled easily by setting the
pressure of the generated steam.

Pada outlet steam reformer, reaktor oksidasi parsial atau unit gas oven
kokas, syngas mengandung H2, CO, CO2, CH4 dan air dalam kesetimbangan kimia
pada suhu tinggi di kisaran 700 sampai 1400 C tergantung pada tekanan
proses dan campurannya. Stok pakan dan proses uap atau air.
Dengan menggunakan konversi pergeseran CO, bagian penting dari kandungan CO
dalam gas retak digunakan untuk penambahan pembangkit hidrogen, yang
mengikuti reaksi kimia.
CO + H2O <=> H2 + CO2
Proses ini bersifat eksotermik dan dibatasi oleh ekuilibrium kimia.
Ada tiga versi konversi pergeseran CO yang berbeda:
Konversi pergeseran CO suhu tinggi (HT) sekitar 300 sampai 450 C sampai
kira-kira. 2,5% CO pada dasar kering di outlet reaktor
Medium temperature (MT) CO shift conversion atau yang disebut konversi
pergeseran isotermal sekitar 220 sampai 270 C sampai kira-kira. 0,5% CO
pada dasar kering di outlet reaktor.
Konversi pergeseran CO suhu rendah (LT) sekitar 180 sampai 250 C sampai
kira-kira. 0,2% CO pada dasar kering di outlet reaktor
Untuk setiap proses katalis khusus akan digunakan dalam reaktor unggun tetap
untuk mendapatkan hasil maksimal produk H2.
Penggunaan konversi pergeseran HT CO adalah keadaan seni di hampir setiap
pabrik hidrogen.
Penerapan konversi pergeseran CO suhu rendah biasanya dipasang di hilir
pergeseran HT pada konten CO yang telah berkurang dalam gas umpan.
Investasi tambahan dipertimbangkan untuk tanaman yang memiliki kapasitas di
atas sekitar. 40.000 Nm / h H2 produk. Katalis dari pergeseran LT sangat
sensitif terhadap sulfur, klorin dan air cair dan perhatian khusus diperlukan
saat kondisi start up dan plant upset.
Dalam konsep sebelumnya, pergeseran LT penting karena metanisasi hilir CO
mengikuti unit penghilangan CO2, untuk memenuhi kemurnian produk pada
kerugian H2 minimum. Setelah penerapan Pressure Swing Adsorption (unit PSA)
untuk pemurnian H2, langkah-langkah proses ini sudah menjadi usang.
Konversi pergeseran MT CO sebagai reaksi isotermal dapat diperkirakan di
beberapa reaktor adiabatik dengan intercooler atau lebih baik dalam reaktor
isotermal dengan pembangkit uap terintegrasi untuk pendinginan gas proses.
Suhu reaksi pergeseran dikendalikan dengan mudah dengan mengatur tekanan uap
yang dihasilkan.

Das könnte Ihnen auch gefallen