Beruflich Dokumente
Kultur Dokumente
Vega:
Continue this process for all
discovered lights and press
Set the Wired
Whats in the Box Connection OK.
Connection
1 2 3 Vega
1. From the Home screen, press 6. Return to the Home screen to see
Controller 1. From the Home screen, press
MENU. the signal strength of your wireless
Controller
Mini USB (use for firmware Vega Auto Mode Vega MENU.
2. Scroll down to the Setup Lights connection.
Timer# 3, 2, 1
80% 80% 80% To connect the Controller with a Vega module, 2. Scroll down to the Setup Lights
updates)
make sure the LED on the side of the Vega menu option and press SELECT.
3.5 mm cable (use to connect June 26, 2012 1:04:58 PM menu option and press SELECT.
Power supply Timer# 3, 2, 1 5 Press and hold the red button for approxi-
4. Press OK. The Wireless Setup Options as the model and Wired as the
80% 80% 80% 6 mately seven seconds. The light will alternate connection.
back and forth from red to green. window displays and the device This menu is grayed out/unavailable 4. Press OK.
searches for lights. A progress bar before you establish the wireless con-
June 26, 2012 1:04:58 PM 7 indicates the status. nection. You can set the sweep direction
Controller Compatibility MENU ALL OFF 8
5. A message displays, indicating to uniform, left-to-right or right-to-left. Timer Setup
whether lights are detected. If all You can set the sweep speed to auto, or (Easy)
lights are found, press OK. anywhere from 1-10.
1 Wireless Strength If you have multiple modules If you need a simple day and night ramp
2 Module Name connected, you need to indi- or you are just starting out with the
3 Lunar Cycle Indicator cate what order the lights are timers, this is the recommended option
4 Current Mode Wireless Module
Mini-USB Data in above the tank (on the next for setting up timers. The easy setup
To connect a Sol or Nano module with the
5 Active Timers screen that displays). The creates six individual timers in the man-
wireless adapter, press the reset button using
Wireless Wireless* Wireless* Open menus, confirm selections or cancel actions.
6 Current Intensities a paperclip or other object for approximately lights are counted from the ual setup screen. The method behind
Wired Wired
7 Date and Time Modify selections. seven seconds to change the light from green left. A module in the middle the sunrise/sunset ramp up method is to
*Wireless adapter required. (Sold seperately) to red.
8 Current Key Functions Move through menu options. needs to be set as Left +1. begin with the least intensity and ramp
Switch Modes 2. Scroll down to the Switch Modes 4. Set the correct hour, minutes, sec- 1. From the Home screen, press
Factory Reset Declaration of Conformity and is tested to and conforms with the essential radio test suites
FCC Compliance Statement so that it effectively uses the frequency spectrum allocated to
menu option and press SELECT. A onds and select AM or PM. MENU. This device complies with part 15 of the FCC We, the undersigned, terrestrial/space radio communication and orbital resources
so to as to avoid harmful interference, as included in following
Use this menu option to switch back and pop-up message asks if you want 5. Set the correct month, day and 2. Scroll down to the More menu 1. From the Home screen, press
Rules. Operation is subject to the following C2 Development, Inc. standards:
127 S Bell Ave.
to switch to auto mode. year. option and press SELECT. two conditions: Ames, IA 50010 USA Standard Issue date
forth between Auto and Manual modes. MENU. Phone: 515-233-5105
When you switch the controller to manu- 3. Press OK. 6. Set the Auto DST menu option to 3. Scroll down to the Key Sensitivity 2. Scroll down to the More menu ETSI EN 300 440-2 V1.4.1 (2101-08) 12/1/12
(1) This device may not cause harmful inter- certify and declare under our sole responsibility that the following
al mode, the menu options change. 4. The menu options reconfigure to Yes if you want the controller to menu option and press SELECT. option and press SELECT. ference, and
equipment: and therefore complies with the essential requirements and
provisions of the Directive 1999/5/EC of the European Parlia-
display only the relevant options automatically adjust for daylight 4. Select a key sensitivity setting from 3. Scroll down to the Factory Reset (2) this device must accept any interference Product description / Wireless lighting controller ment and of the council of March 9, 1999 on Radio equipment
and Telecommunications Terminal Equipment and the mutual
Intended use
To switch from Auto to Manual mode: for auto configuration. Your original savings time or No if you do not 1-10. menu option and press SELECT.
received including interference that may recognition of their conformity and with the provisions of Annex
IV (Conformity Assessment procedure referred to in article 10).
EU / EFTA member states EU: Austria, Belgium,
settings for auto mode remain want that setting. 5. Press OK. cause undesired operation. Any changes intended for use Cyprus, Czech Republic,
1. From the Home screen, press A warning message displays to or modifications not expressly approved by Denmark, Estonia, Finland, The technical documentation as required by the Conformity
MENU. intact. 7. Press OK. remind you that all of your custom
France, Germany, Greece, Assessment procedure is kept at the following address:
C2 Development Inc. could void the users Hungary, Ireland, Italy, Lat-
C2 Development, Inc.
Firmware Update
via, Lithuania, Luxembourg,
2. Scroll down More menu option and settings for timers and effects will authority to operate the wireless radio module, Malta, The Netherlands, 127 S Bell Ave.
Poland, Portugal, Slovakia, Ames, IA 50010 USA
and/or the product that incorporates the wire-
press SELECT.
3. Scroll down to the Switch Modes
Set the Clock Key Sensitivity 4.
be erased if you proceed.
Press OK.
less radio module.
Slovenia, Spain, Sweden,
United Kingdom
Phone: 515-233-5105
display only the relevant options for latest firmware updates are available.
Videos is tested to and conforms with the essential requirements for
MENU. number. To adjust the keys so they are For videos on use and
protection of health and the safety of the user and any other
person and Electromagnetic Compatibility, as included in Name and position Chris Clough - President
operating the controller manually. 2. Scroll down to the More menu more sensitive, requiring less pressure following standards:
setup scan the QR code
option and press SELECT. when you press a key, select a lower Note: to visit our YouTube Standard Issue date
To switch from manual to auto mode: 3. Scroll down to the Set Clock menu number. For best performance, make sure the controller is page ETSI EN 301 489-1 V1.8.1 (2008-04) 12/1/12
ETSI EN 301 489-3 V1.4.1 (2002-08)
1. From the Home screen, press option and press SELECT.
located near your lights to prevent signal interruption IEC 60950-1:2006 Information technology
during firmware updates. equipment Safety Part 1
MENU.