Beruflich Dokumente
Kultur Dokumente
Partitioning Solutions
1
2
CONTENTS
Lafarge
Partitioning Solutions
01 LAFARGE PLASTERBOARD
02 LAFARGE FIXED PARTITION
03 LAFARGE FINESSE DEMOUNTABLE PARTITION
04 LAFARGE TOILET PARTITION
3
LAFARGE PLASTERBOARD
Lafarge
Plasterboard.
4
LAFARGE PLASTERBOARD
Square 6.4 1200 900; 2400; 2700; 3000; 3300; 3600 5.50 Ceilings
Edge
9 S/E can be manufactured to order with minimum quantities
5
LAFARGE PLASTERBOARD
Other Tests:
Gridlock deflection - SANS 7228/158EMTO1
Sag Test BS 8290
Sag Test TDC MO3-TDC-022D
SANS/ASTM 367-89
7228/013/MT01/REVA
5544/158C/MT01
7228/158C/MT01
7228/112A/MT01
Pull Test Lafarge Gypsum - TDC M02-TDC-023-D
6
LAFARGE PLASTERBOARD
For use in office partitioning, residential internal walling, shopping centres, hotels, hospitals, schools or wherever a 2 hour
fire rating or a safe/secure wall is required.
Application Details:
Set 63.5mm studs spaced at 600mm intervals into
65mm track at floor and ceiling.
Apply a base layer of 12.5mm Lafarge Extra Fire
Resistant Plasterboard vertically to each side using
0.5mm
25mm Drywall Screws spaced at 220mm intervals.
Galvanised Steel
Sheet Fix a layer of 0.5mm galvanised steel sheeting
using 25mm drywall screws.
63.5mm Stud
Apply the face layer of 12.5mm Lafarge Extra Fire
12.0mm Lafarge Firecheck
Plasterboard Resistant Plasterboard vertically to each side using
12.5mm Lafarge Firecheck 41mm Drywall Screws spaced at 220mm intervals.
Plasterboard
65mm Track
Use Fibatape and Lafarge Jointing Plaster over the
Acoustic Sealant/Gasket joints.
All joints are to be staggered
Acoustic enhancement requires sealing between
track, floor, ceiling and any other abutment joints.
7
LAFARGE PLASTERBOARD
Plasterboard.
Check Plasterboard.
Framing Installation:
Floor Track
8
LAFARGE PLASTERBOARD
to set. Apply the second (if required) coat and leave it for 2 hours. Smooth with sand paper.
25mm Screw
1. Cut the corner bead to the same length as the Corner Bead
Lafarge
Jointing Plaster approximately 3mm thick. Leave for
70 minutes to set.
5. Apply the second coating about 300mm wide from Lafarge Plasterboard
(Ceiling)
80 grit sandpaper.
9
LAFARGE PLASTERBOARD
JOINT CONCEALING
There are three steps to concealing joints:
Lafarge
Fixed Partition.
Lafarge Drywall is a lightweight non-demountable partition Bubble Seal Gasket (or optional woolpile) easily clips
system which has no visible joints on completion. The into place after the glass has been positioned, leaving
internal framework consists of standard Ridgeback Stud an attractive Aluminium shopfront type finish, having
and Drywall Track profiles manufactured from galvanised slim and clean lines. The Bubble Seal Gasket will
steel. Tapered edge plasterboards are screw fixed to the accommodate glass thickness from 4 mm to 6 mm.
studs allowing for plaster jointing. Paint or wallpaper (nominal thickness).
finishes can then be applied for a joint free wall of
subtle quality. Fire rating: Lafarge Drywall (89 mm
partition) has a 30 minute fire rating as per SABS
Attractive Slimline Glazing Mullions and transoms can 0177: Parts-1981. For further details as well as
be created by clip fixing the required aluminium male information on 60 minutes plus fire ratings please
section onto its four legged female partner which has consult with our technical staff.
already been fixed into position.
All Lafarge Aluminium sections may be
Door Frame Kits are supplied premitred and with Powder Coated or Anodised to complement the
optional lock cutouts. Full height Door Frames clip decorated finish of the boards. Aluminium Skirting
directly onto the Aluminium Female ceiling trim by or recessed base can be similarly treated to match or
means of the Male Aluminium Door header. Standard contrast as required.
door frame kits have both styles and header manufac-
tured from four legged Female Aluminium Door Frame
sections. It is recommended that for additional stability
when erecting full height doors the Ridgeback Stud
should be boxed onto the open side of a Floor Track
prior to fixing (the Female Door Frame Section). Refer
to Fig 6 Pg 7.
11
LAFARGE FIXED PARTITION
COMPONENTS
Connecting Lafarge Partition Solutions
12
LAFARGE FIXED PARTITION
ALTERNATIVE ALUMINIUM
13
LAFARGE FIXED PARTITION
14
LAFARGE FIXED PARTITION
ALTERNATIVE ALUMINIUM
15
LAFARGE FIXED PARTITION
CONSTRUCTION DETAILS
16
LAFARGE FIXED PARTITION
CONSTRUCTION DETAILS
6 Door Frame/Glazing Mullion
1 Aluminium 4 Leg Female Doorframe
2 Lafarge Ridgeback Stud
3 Aluminium Male Glazing Section Die 6667/6678
4 Aluminium Glazing Bead Die 6674
5 4 - 6 mm Glass
6 Door (40 mm)
7 Pop Rivets
8 Bubble Seal Gasket
9 Standard Corner
1 Lafarge Ridgeback Stud
2 Drywall Corner Bead
3 Lafarge Plasterboard
4 Drywall Screws
5 Skimmed Corner
10 Recessed Base
(alternative to figure 3)
1 Aluminium recessed Base Die 6206/6207
2 Lafarge Ridgeback Stud
3 Lafarge Plasterboard
4 Drywall Screws
17
LAFARGE FIXED PARTITION
Cover Plate
Die 1829
2 Glazing Mullion
1 Aluminium 4 Leg Female Glazing Die 6677
2 Aluminium Glazing Bead Die 6635
3 Lafarge Ridgeback Stud 58mm
4 Lafarge Plasterboard
5 4 - 6 mm Glass
6 Drywall Screws
7 Bubble Seal Gasket
18
LAFARGE FIXED PARTITION
3 Door Frame
1 Aluminium 4 Leg Female Doorframe Die 6633
2 Lafarge Ridgeback Stud
3 Lafarge Plasterboard
4 Door (40 mm)
5 Drywall Screws
6 Bubble Seal Gasket
7 Aluminium Sinkless Hinge
Installation to be in accordance with SABISA (South African Installation to be in accordance with SABISA (South African
Building Interior Systems Association) installation guidelines. Building Interior Systems Association) installation guidelines.
19
LAFARGE FIXED PARTITION
Fire rating: Lafarge Residential (89 mm partition) has a The Lafarge Plasterboards are held in place at the base by
30 minute fire rating as per SABS 0177: Parts 1981. For the skirting and fixed to the steel framework with 25mm
further details as well as information on 60 minutes plus drywall screws. Where the Lafarge Fixed Partition is being
fire ratings please consult with our installed beneath a plastered ceiling, Lafarge Galvanised
technical department. Drywall Track is fixed to the ceiling.
All Steel
components of
the Lafarge
Partition System are
manufactured by
Lafarge Gypsum Reg
No. 1997/08520
ISO9001 - 2002
20
LAFARGE FIRE RATED PARTITION SYSTEMS
WALL PROPERTIES
51mm stud A: Lafarge 58mm steel stud
Sound insulation reduction index - 36dB
Thickness - 76mm
Approximate weight - 20kg/m2
MATERIAL USED
A - 51mm Drywall Lafarge steel stud B: Lafarge steel track
B - 52mm Drywall Lafarge steel track
C - 12mm Standard Tapered edge Plasterboard
- 25mm Drywall Screws
- Lafarge Drywall jointing system
- Floor and ceiling finishes as per specification
APPLICATION DETAIL
1. Set Lafarge steel studs spaced at 600mm c/c into steel track at
floor and ceiling.
2. Apply a single layer of 12mm Lafarge Taper edge plasterboard to
each side side using 25mm drywall screws spaced at 220mm c/c.
3. Tape and joint according to specification.
4. Refer to standard specification.
C: Lafarge 12mm Plasterboard
5. Accoustic performance requires sealing between track, floor, ceiling
and any other abutment joints.
6. Stagger the plasterboard joints in the system.
MATERIAL USED
A - 58mm Drywall Lafarge steel stud
B - 59mm Drywall Lafarge steel track
C - 15mm Fire Check Tapered edge Plasterboard
- 25mm Drywall Screws
- Lafarge Drywall jointing system
- Floor and ceiling finishes as per specification
21
LAFARGE FIRE RATED PARTITION SYSTEMS
MATERIAL USED A:
A: Lafarge
Lafarge 64mm steelstud
64mm steel stud
A - 64mm Drywall Lafarge steel stud
B - 65mm Drywall Lafarge steel track
C - 12mm Standard Tapered edge Plasterboard
- 25mm Drywall Screws
- Lafarge Drywall jointing system
- Floor and ceiling finishes as per specification
APPLICATION DETAIL
1. Set Lafarge steel studs spaced at 600mm c/c into steel track
at floor and ceiling. C: Lafarge 12mmPlasterboard
C: 12mm Plasterboard
2. Apply a single layer of 12mm Lafarge Taper edge plasterboard to
each side using 25mm drywall screws spaced at 220mm c/c.
3. Tape and joint according to specification.
4. Refer to standard specification.
5. Accoustic performance requires sealing between track, floor, B:B:Lafarge
Lafarge65mm
65mmsteel
steel track
track
ceiling and any other abutment joints.
6. Stagger the plasterboard joints in the system.
MATERIAL USED
A - 64mm Drywall Lafarge steel stud
B - 65mm Drywall Lafarge steel track
C - 15mm Fire Check Plasterboard
- 25mm Drywall Screws
- Lafarge Drywall jointing system
- Floor and ceiling finishes as per specification
APPLICATION DETAIL
1. Set Lafarge steel studs spaced at 600mm c/c into steel track
at floor and ceiling.
C: Lafarge 15mm Check board
board
2. Apply a single layer of 15mm Fire Check Taper edge plasterboard to C: 15mm Fire Check
22
LAFARGE FIRE RATED PARTITION SYSTEMS
WALL PROPERTIES
64mm stud 600,00
60min fire rating
Sound reduction index - 45dB
Thickness - 112mm
Approximate weight - 39kg/m2
MATERIAL USED
A - 64mm Drywall Lafarge steel stud C: 12mm
C: LafargePlasterboard
12mm Plasterboard
APPLICATION DETAIL
1. Set Lafarge steel studs spaced at 600mm c/c into steel track
at floor and ceiling.
2. Apply a single layer of 12mm standard plasterboard vertical to both
sides using 25mm drywall screws spaced at 220mm c/c, stagger joints.
3. Apply a face layer of 12mm standard plasterboard to both sides
staggering all joints, using 41mm drywall screws spaced at 220mm c/c.
4. Tape and joint according to specification.
B:B:Lafarge
Lafarge65mm
65mmsteel
steeltrack
5. Refer to standard specification. track
WALL PROPERTIES
64mm stud
60min fire rating
Sound reduction index with insulmatt wire mesh surfaced fibre blanket A: Lafarge
Lafarge 64mm
64mm steel
steelstud
stud
80kg/m3 - 49dB
Thickness - 89mm
Approximate weight - 30kg/m2 InsulmattInsulation
Insulmatt Insulation
MATERIAL USED
A - 64mm Drywall Lafarge steel stud
B - 65mm Drywall Lafarge steel track
C - 12,5mm Fire Check board
- 25mm Drywall Screws
- Lafarge Drywall jointing system
- Floor and ceiling finishes as per specification
- Insulmatt wire mesh surfaced fibre blanket of 80kg/m3 C: LafargeC: 12,5mmFire
12,5mm Checkboard
FireCheck board
APPLICATION DETAIL
1. Set Lafarge steel studs spaced at 600mm c/c into steel track at floor and ceiling.
2. Apply a single layer of 12,5mm Fire Check board vertical to one side using
25mm drywall screws spaced at 220mm c/c.
3. Position Insulmatt insulation between studs, fold the top over and secure to top
track by positioning and fixing with galvanised angle. Lafarge 65mm
B: Lafarge 65mm steel
steeltrack
track
4. Apply a single layer of 12,5mm Fire Check board vertical to the other side
using 25mm drywall screws spaced at 220mm c/c.
5. Tape and joint according to specification.
6. Refer to standard specification.
7. Accoustic performance requires sealing between track, floor, ceiling and any
other abutment joints.
8. Stagger the plasterboard joints in the system.
23
LAFARGE FIRE RATED PARTITION SYSTEMS
APPLICATION DETAIL
1. Set Lafarge steel studs spaced at 600mm c/c into steel at floor and ceiling.
2. Apply a single layer of 12,5mm taper edge Fire Check plasterboard
vertical to one side using 25mm drywall screws spaced at 220mm c/c.
3. Apply 0,5mm galvanised steel sheet to each side (min 30mm overlap).
4. Apply a face layer of 12,5mm taper edge Fire Check plasterboard to
both sides.
D: 0.5mm
D: galvanised steel
0,5mm galvanised steelsheet
sheet
5. Tape and joint according to specification.
6. Refer to standard specification. B:
B: Lafarge
Lafarge65mm
65mm steel
steel track
track
7. Accoustic performance requires sealing between track, floor, ceiling and
any other abutment joints.
8. Stagger the plasterboard joints in the system.
WALL PROPERTIES
64mm stud
120min fire rating
Sound reduction index - 48dB .
600mm
Thickness - 124mm
Approximate weight - 45.5kg/m2
MATERIAL USED
A - 64mm Lafarge Drywall steel stud C: Lafarge
C: 15mm
15mm Fire CheckFire Check board
board
B - 65mm Lafarge Drywall steel track
C - 15mm Fire Check tapered edge plasterboard
- 25mm and 41mm Drywall Screws A: Lafarge
Lafarge 65mm steelstud
64mm steel stud
- Lafarge Drywall jointing system
- Floor and ceiling finishes as per specification
APPLICATION DETAIL
1. Set Lafarge steel studs spaced at 600mm c/c into steel track at floor
and ceiling.
2. Apply a single layer of 15mm Technical Fire Check plasterboard vertical
to both sides. using 25mm drywall screws spaced at 220mm c/c,
stagger joints.
3. Apply a face layer of 15mm Technical Fire Check plasterboard to both
sides staggering all joints, using 41mm drywall screws spaced at
220mm c/c.
4. Tape and joint according to specification.
5. Refer to standard specification.
6. Accoustic performance requires sealing between track, floor, ceiling and
any other abutment joints. B:B:Lafarge
Lafarge65mm
65mmsteel
steel track
track
24
LAFARGE FIRE RATED PARTITION SYSTEMS
APPLICATION DETAIL
1. Set Lafarge steel studs spaced at 600mm c/c into steel track at
floor and ceiling.
2. Apply a single layer of 15mm Fire Check Taper edge plasterboard to
each side using 25mm drywall screws spaced at 220mm c/c. B: Lafarge
B: Lafarge 103mm
103mm steel track
3. Tape and joint according to specification.
4. Refer to standard specification.
5. Accoustic performance requires sealing between track, floor, ceiling and
any other abutment joints.
6. Stagger the plasterboard joints in the system.
APPLICATION: Residential
MATERIAL USED
A - 102mm Drywall Lafarge steel stud C: Lafarge
C: 15mm
15mm Fire
Fire Check board
APPLICATION DETAIL
1. Set Lafarge steel studs spaced at 600mm c/c into steel track at floor and ceiling.
2. Apply a single layer of 15mm Technical Fire Check plasterboard vertical
to both sides using 25mm drywall screws spaced at 220mm c/c,
stagger joints.
3. Apply a face layer of 15mm Technical Fire Check Plasterboard to both sides. B:
B: Lafarge
Lafarge103mm
103mm steel track
4. Tape and joint according to specification.
5. Refer to standard specification.
6. Accoustic performance requires sealing between track, floor, ceiling and
any other abutment joints.
7. Stagger the plasterboard joints in the system.
8. Maximum Partition height 4,5m.
25
LAFARGE FINESSE DEMOUNTABLE
PARTITION SYSTEM
Lafarge Finesse
Demountable Partition System
26
LAFARGE FINESSE DEMOUNTABLE PARTITION
POSTS
Double Centre
glazing glazing
Centre
glazing
Double
glazing
Offset
glazing Lafarge Plasterboard
3 Way Y Post showing three different floor 4 Way Box Post showing partition board and full height
glazing details. glazing details.
Centre
Centre glazing
glazing
Lafarge Plasterboard
Main Post showing centre glazing details . Main Post showing partition board and centre
glazing details.
Centre
glazing
Door Stop
27
LAFARGE FINESSE DEMOUNTABLE PARTITION
76mm
40mm
Flat Infill 76mm
Die 1829 (FA 542) Door Stop
Die 6325 (FA 531)
76mm
44mm
Strong Post
Die 6322 (FA 500) 6 Glazing 35mm
2 88mm
76mm
Main Post 76mm Centre Glazing Chair
Die 6323 (FA 510) Die 1841 (FA 600)
FA540 Curved Infill
Die 6326 (FA 540) 60mm
3 Skirting
Offset Glazing Chair
20mm
12mm
20mm
27mm/40mm
Cover Trim
61mm
28
LAFARGE FINESSE DEMOUNTABLE PARTITION
ALUMINIUM ABUTMENTS
7 8
76
m
m
88mm
95mm
11 109mm
88mm
76mm
9 76mm 10 76mm
76mm
88mm
4 Way Post
Die 53974
88mm 3 Way Y Post
Die 6343 (FA 580)
29
LAFARGE FINESSE DEMOUNTABLE PARTITION
Table A
Board TRK DSTE
mm Friction Stud
Track
9.0 56 55
12.0 50 48
DSTE Stud 15.0 45 43
TRK Friction Track
Finesse Hinge Located in Door Stop
Partition Board
(Thickness refer table A above)
Power Skirting
Die 28456
Rolled Galvinised Material
code FCL Clamping Strip
Ezee-Clip
4mm
Cover Plate
Die 1829
15.3mm
19mm
Fixing
Power Skirting
Die 28456
30
LAFARGE FINESSE DEMOUNTABLE PARTITION
DETAILS
HEAD AND FLOOR DETAIL 5
2
2 Solid Floor Detail Using Partition Board 3
5
1. TRK Friction Track (Dimension refer table A Page 24)
2. DSTE Stud (Dimension refer table A Page 24) 6
3. Lafarge Plasterboard (Thickness refer table A Page 24)
4. Clamping Strip 4
5. 40mm/75mm/100mm Skirting
6. Fixing 1
7. Fixing (mechanical / velcro)
7
GLAZING DETAIL
3 Full Height Centre Glazing 4
5 3
1. Main Post Die 6323 (FA 510) 2
2. Centre Glazing Chair Die 1841 (FA 600) 2
3. Centre Glazing Bead Die 1842 (FA 620)
4. MXG Bubble Seal Gasket
1
5. 6mm Glass
6. Floor level
31
LAFARGE FINESSE DEMOUNTABLE PARTITION
DETAILS
DOOR FRAME DETAIL 5
2
Note: Before fixing Main Post Door Transom cut and position Partition 4
3
Board above
7
10
BOARD JOINT DETAILS
1 4 4
3
1. TRK Friction Track (Dimension refer table A Page 24) 5
DETAILS
11 90 Corner Post Showing Clip on Door Stop and Board Detail 1
9. Finesse Hinge 2
8
12 3 Way Box Post Showing Clip on Door Stop, Centre Glazing and Curved Infill Detail
5. 4 - 6 mm Glass 4
6. Door Stop Die 6325 (FA 531)
7. 40 mm Door 3
8
13 3 Way Y Post Showing Clip on Door Stop, Double Glazing and
Flat Infill Detail
5
14 135/45 Corner Detail Showing Clip on Door Stop and Board Details 5
9. Fixing 2 4
3
15 4 Way Box Post Showing Clip on Door Stop\Glazing\Angle Infill and Board Detail
8
33
LAFARGE FINESSE DEMOUNTABLE PARTITION
SPECIFICATION
All aluminium and steel components for the Lafarge Finesse It is recommended that Lafarge Plasterboards be
Demountable Partition System to be in accordance with covered prior to installation. This minimises on site work and
components listed in diagrams pages 3, 4, 5 & 6 and shall be mess, although plain Lafarge Plasterboards can be
installed in strict accordance with the design specification and fitted for decoration in situ. Refer to Head and Floor Details
manufacturers instructions. Fig.1.2 page 24 / Board joint details page 25 Detail B.
Step 2
Step 1
SPECIFICATIONS
C: Glass Lafarge Finesse Demountable Partition System.
The Lafarge Finesse Demountable Partition System clip in Supply and install Lafarge Finesse Demountable Partition
glazing sections, including the Bubble Seal Gasket, have been System from Lafarge Gypsum with overall thickness of 88mm
designed to accept glass from 4mm to 6mm nominal thickness. comprising of internal framing formed of 48mm Finesse
Where thicker glass is installed, the Bubble Seal Gasket to the galvanised steel studs clipped into position at 600mm centers into
Glazing Chair can be omitted. Alternatively, Woodpile can be Finesse galvanise steel friction track top and bottom, including
installed instead of the Bubble Seal Gasket. where necessary, any additional Finesse steel friction track to
be secured to aluminium door openings, glazing, angles corners,
Complementary Accessories head, termination and floor. The internal steelframing is to be
dressed both sides with 12mm thick 1195mm wide pre-laminated
A full range of complementary accessories are available in the square edge Lafarge plasterboard (specific finish) in single lengths
form of Rounded 90 Corner Post, 135/45Corner Post, 3 Way to suite height and secured to the Finesse steel studding with
Box Post, 3 Way Y Post, 4 Way Box Post, including a full range galvanised steel clamping strips finished with aluminium clip-on
of moulded Capping Pieces to close open ends of Aluminium cover trim. All exposed aluminium, head sections, wall sections,
sections in low level applications. Various configurations using the glazing sections, door frames, corner sections, cover trims, clip-in
full range of add-on fittings are available. When used in a partition glazing, clip-in door and skirting are to be formed of (natural anod-
wall application, these sections to run full height floor to ceiling. ized/colour anodized/power coated to specific colour, aluminium
Refer to Junction Accessories. sections. Maximum height of 3600mm.
Aluminium
Power Skirting
35
LAFARGE TOILET PARTITIONS
Lafarge
Toilet Partitions
Flexible cubicle configurations also cater for the In offering this product, Lafarge Gypsum considers
requirements of the disabled, making this partitioning reliability, quality and consistency to be the prime
solution the number one choice for many installations. benefits of our toilet cubicles.
36
LAFARGE TOILET PARTITIONS
DESCRIPTION OF COMPONENTS
Infill Panels Ironmongery
There are two aluminium frame channels available to cater for two Ironmongery to Doors
different finished thicknesses.
Each door is fitted with a pair of satin finished hinges, indicator
1. Lipped Channel: Accommodates 16mm chipboard with bolt and keep, as well as a hat and coat hook with rubber
either Mellawood or Melamine facing. buffer, which serves as a door stop. The pilaster frame against
2. Un-lipped Channel: Accommodates 19mm Formica clad which the door strikes is fitted with two rubber buffers.
chipboard.
Ironmongery to Partitions
The Formica clad chipboard is the more durable of the two.
Intermediate and end-partitions should be fitted with toilet roll
Framing holders.
25
Intermediate and end-partitions, doors and pilasters are neatly 68 25
Skirting
151 151
A 44mm high aluminium skirting (optional) can be formed at the
base of pilasters by fixing 22 X 22mm inverted channel to the floor Front Elavation End Elavation
before fixing the pilaster in position, this prevents possible water
contact with the base of the pilaster.
Transom
Junction Walls
37
LAFARGE TOILET PARTITIONS
900 1200
Typical Dimensions 230
Typical take off - Bill of Material for the toilet cubicle layout in
1500 or 1800
1500 or 1800
diagram for pricing and ordering purposes
Partitions
End-Partition 1 800mm x 1 830 x 1
900 670
Intermediate Partition 1 800mm x 1 830 x 1 115
1200
Doors 762mm x 1 762 x 2 115
PLAN
Intermediate Pilaster 230mm x 1 981 x 1
End-Pilaster 115mm x 1 981 x 2
Specification
Aluminium Sections
Receiving Channel n/a 1 830mm x 3 Supply and install Lafarge Gypsum Toilet Partition System
(for int. and end-partitions- walls) comprising 16mm thick particle board panels, laminated both
Receiving Channel n/a 1 981mm x 1 sides with stock colours available in our Mellawood range [stock
(for end-pilasters - walls) colours are: Peen White, White, Folkstone Grey, Syringa.
Receiving Channel n/a 230mm x 1 Non-stock Mellawood colours and Formicas will be subject to
(for int. pilaster - floor) special lead times.], edged all round with 22 x 22mm lipped
Receiving Channel n/a 115mm x 1 channel and fixed into position by means of full height vertical
(for end-pilaster - floor) aluminium receiving channels plugged to walls and fixed to
90 Corner Post n/a 1 981mm x 1 pilasters. Partitions are to be supported by a continuous 25 x
(junction between end-partition and pilaster for last cubicle where there is 25mm aluminium transom section over doors and supplied with a
no brick wall) complete set of standard ironmongery comprising of indicator
Transom Tube n/a 5 000mm x 1 bolts, hat and coat hooks, doors stops, toilet roll holders and
(supplied in full lengths, runs the length of entire wall to wall cubicle rubber buffers. All exposed aluminium sections are to be natural
layout) anodised / colour anodised / powder coated to specified colour.
Channels
24mm
22mm
22mm
COMPONENTS
B
A= 58mm (Hinge Overlap)
B= Door Opening
C= 22mm (Closing Overlap)
D= Actual Door (Varies +A 58mm)
+ C (22mm)
E= Door Hinge
C B A
D
Transom
Intermediate Partition
Intermediate Pilaster
Protective Skirting
fixed to floor Floor Channel Fixing
39
LAFARGE GYPSUM HEAD OFFICE
18 Barium Street
Alrode Ext 7 1449
P O Box 167025
Brackendowns 1454
Tel: (+27 11) 389 4500
Fax: (+27 11) 864 6816
www.lafarge.co.za
0861 GYPSUM
(497786)
40