Beruflich Dokumente
Kultur Dokumente
1. Additional table for wide strip is included which is based on Japanese practice.
2. Slightly different edge camber tolerances than in EN 10259 for wide strip.
3. Provision for width tolerance on wide strip with mill edges.
Narrow strip is defined as having a rolled width of < 600mm and thickness < 3mm. This is the same
definition as in EN 10258. This covers material slit from such products and cut lengths.
Wide strip is defined as having a rolled width of 600 - 2100 mm from 0.3-8.0mm thick. It therefore includes
material slit from this product with actual width < 600mm and sheet/plate
The phrase "specified thickness" is preferred to "nominal thickness" in this ISO standard.
There is a view that the combination of all cold rolled products into one standard can be confusing. There
are moves towards separating out narrow and wide products into two standards. This summary adopts this
approach as for every tolerance type there are different values for narrow and wide products.
Narrow strip
Thickness tolerance
Tolerances on specified thickness for
narrow cold rolled strip
w < 125 125 < w < 250 250 < w < 600
Specified Thickness (t)
Nor Fine Precisio Nor Fine Precisio Nor Fine Precisio
mal (F) n(P) mal (F) n(P) mal (F) n(P)
0.1 0.06 0.1 0.10 0.1 0.10
0.05 < t < 0.10 0.04t 0.08t 0.08t
0t t 2t t 5t t
0.0 0.00 0.0 0.01 0.0 0.01
0.10 < t < 0.15 0.006 0.008 0.010
10 8 15 2 20 5
0.0 0.01 0.0 0.01 0.0 0.01
0.15 < t < 0.20 0.008 0.010 0.012
15 0 20 2 25 5
0.0 0.01 0.0 0.01 0.0 0.02
0.20 < t < 0.25 0.008 0.010 0.012
15 2 20 5 25 0
0.0 0.01 0.0 0.01 0.0 0.02
0.25 < t < 0.30 0.009 0.012 0.015
17 2 25 5 30 0
0.0 0.01 0.0 0.02 0.0 0.02
0.30 < t < 0.40 0.010 0.012 0.015
20 5 25 0 30 5
0.0 0.02 0.0 0.02 0.0 0.02
0.40 < t < 0.50 0.012 0.015 0.018
25 0 30 0 35 5
0.0 0.02 0.0 0.02 0.0 0.03
0.50 < t < 0.60 0.014 0.015 0.020
30 0 30 5 40 0
0.0 0.02 0.0 0.03 0.0 0.03
0.60 < t < 0.80 0.015 0.018 0.025
30 5 35 0 40 5
0.0 0.02 0.0 0.03 0.0 0.03
0.80 < t < 1.00 0.018 0.020 0.025
30 5 40 0 50 5
0.0 0.03 0.0 0.03 0.0 0.04
1.00 < t < 1.20 0.020 0.025 0.030
35 0 45 5 50 0
0.0 0.03 0.0 0.03 0.0 0.04
1.20 < t < 1.50 0.020 0.025 0.030
40 0 50 5 60 5
0.0 0.03 0.0 0.04 0.0 0.05
1.50 < t < 2.00 0.025 0.030 0.035
50 5 60 0 70 0
0.0 0.03 0.0 0.04 0.0 0.06
2.00 < t < 2.50 0.025 0.030 0.040
50 5 70 5 80 0
0.0 0.04 0.0 0.05 0.0 0.07
2.50 < t < 3.00 0.030 0.035 0.045
60 5 70 0 90 0
1. This table is identical to the table in EN 10258.
2. By agreement the tolerances may alternatively be totally + or totally - or unevenly distributed. In any
case the total tolerance shall be as in the table.
3. For thicknesses below 0.05mm the values for the tolerances are to be agreed at the time of the
enquiry and order.
Width tolerance
Tolerances on width for narrow cold rolled strip and cut lengths
Specified Specified Width (w)
w < 40 40 < w < 125 125 < w < 250 250 < w < 600
Thickness Normal Fine Precisio Normal Fine (F) Precisio Normal Fine Precisio Normal Fine Precisio
(t) (F) n (P) n (P) (F) n (P) (F) n (P)
+0.17/- +0.13/- +0.10/- +0.20/- +0.15/- +0.12/- +0.25/- +0.20/- +0.15/- +0.50/- +0.50/- +0.40/-
t < 0.25
0 0 0 0 0 0 0 0 0 0 0 0
0.25 < t < +0.20/- +0.15/- +0.12/- +0.25/- +0.20/- +0.15/- +0.30/- +0.22/- +0.17/- +0.60/- +0.50/ +0.40/-
0.50 0 0 0 0 0 0 0 0 0 0 0 0
0.50 < t < +0.25/- +0.20/- +0.15/- +0.25/- +0.22/- +0.17/- +0.40/- +0.25/- +0.20/- +0.70/- +0.60/- +0.50/-
1.00 0 0 0 0 0 0 0 0 0 0 0 0
1.00 < t < +0.25/- +0.22/- +0.15/- +0.30/- +0.25/- +0.17/- +0.50/- +0.30/- +0.22/- +0.70/- +0.60/-
+1.0/-0
1.50 0 0 0 0 0 0 0 0 0 0 0
1.50 < t < +0.40/- +0.25/- +0.20/- +0.60/- +0.40/- +0.25/- +0.80/- +0.60/-
--- --- --- +1.0/-0
2.50 0 0 0 0 0 0 0 0
2.50 < t < 3. +0.50/- +0.25/- +0.40/- +0.25/- +1.0/- +0.80/-
--- --- --- +0.3/-0 +0.6/-0 +1.2/-0
00 0 0 0 0 0 0
Tolerances on edge camber for cold rolled narrow strip and cut lengths
Edge camber tolerances for measuring lengths
Specified
1000 2000 1000 2000
width w
Normal Precision
10 < w < 25 4 16 1.5 6
25 < w < 40 3 12 1.25 5
40 < w < 125 2 8 1.0 4
125 < w < 600 1.5 6 0.75 3
1. This table is identical to the one in EN 10258.
2. If applicable, both measuring lengths shall be used.
3. These tolerances do not apply to the work hardened condition. Any requirement for this material
shall be agreed at the time of enquiry and order.
Out of squareness
The out of squareness tolerance for cut lengths from narrow strip > 250mm shall not exceed 0.5% of the
actual width of the product.
For widths < 250mm the tolerances shall be agreed at the time of enquiry and order.
Flatness
The flatness tolerance for cut lengths from narrow strip shall not exceed 10mm for normal cases and 7mm
where a special tolerance is required.
This does not apply to material in the work hardened condition which must be agreed at the time of the
enquiry and order.
Edge Waviness
For skin passed or stretch levelled narrow strip, the ratio of the wave height to wave length shall be a
maximum of 0.03 for specified thicknesses < 1.00mm and a maximum of 0.02 for > 1.00mm.
These requirements are identical to those in EN 10258.
------------------------------------------------------------------------------------------------------------------------------------------------
---------
Wide strip
Thickness tolerance
The standard allows for two methods for defining thicknesses tolerance:
Method A - identical to EN 10259. Thickness is measured at any point located more than 20mm from the
edge for slit edges and 30mm for mill edges.
Method B - Thickness is measured at any point located more than 15mm from the edge for slit edges and
25mm for mill edges. This is similar to Japanese standards.
Tolerances on specified thickness for cold rolled wide strip Method A
Normal tolerances for a nominal Special tolerances (S) for a nominal
Specified thickness width w of width w of
(t) w<100 1000<w<1300</ 1300<w<2100</
w<1000 1000<w<1300</w 1300<w<2100</w
0 w w
t < 0.30 0.030 -- -- 0.020 -- --
0.30 < t < 0.50 0.04 0.04 -- 0.025 0.030 --
0.045
0.50 < t < 0.60 0.05 -- 0.030 0.035 --
0.60 < t < 0.80 0.05 0.05 -- 0.035 0.040 --
0.055
0.80 < t < 1.00 0.06 0.06 0.040 0.045 0.050
1.00 < t < 1.20 0.06 0.07 0.07 0.045 0.045 0.050
1.20 < t < 1.50 0.07 0.08 0.08 0.050 0.055 0.060
1.50 < t < 2.00 0.08 0.09 0.10 0.055 0.060 0.070
2.00 < t < 2.50 0.09 0.10 0.11 -- -- --
2.50 < t < 3.00 0.11 0.12 0.12 -- -- --
3.00 < t < 4.00 0.13 0.14 0.14 -- -- --
4.00 < t < 5.00 0.14 0.15 0.15 -- -- --
5.00 < t < 6.50 0.15 0.15 0.16 -- -- --
6.50 < t < 8.00 0.16 0.17 0.17
1. This table is similar to that in EN 10259 except that there is an extra line for 6.50 < t < 8.00.
2. Also there are some differences in the number of decimal places for Special tolerances.
3. Thickness is measured at any point located more than 20mm from the edge for slit edges and
30mm for mill edges - defined as Method A.
4. For strip and cut lengths < 30mm wide the thickness shall be measured at the centre of the strip.
Tolerances on specified thickness for cold rolled wide strip Method B
Normal tolerances for a nominal Special tolerances (S) for a nominal
Specified thickness width w of width w of
(t) w<100 1000<w<1300</ 1300<w<2100</
w<1000 1000<w<1300</w 1300<w<2100</w
0 w w
t < 0.30 0.030 -- -- 0.030 -- --
0.30 < t < 0.50 0.04 0.04 -- 0.030 0.035 --
0.045
0.50 < t < 0.60 0.05 -- 0.035 0.035 --
0.60 < t < 0.80 0.05 0.05 -- 0.040 0.040 --
0.055
0.80 < t < 1.00 0.06 0.07 0.040 0.050 0.050
1.00 < t < 1.20 0.06 0.07 0.08 0.050 0.055 0.060
1.20 < t < 1.50 0.08 0.08 0.10 0.055 0.060 0.060
1.50 < t < 2.00 0.08 0.09 0.11 0.065 0.070 0.080
2.00 < t < 2.50 0.09 0.11 0.13 -- -- --
2.50 < t < 3.00 0.11 0.13 0.15 -- -- --
3.00 < t < 4.00 0.14 0.15 0.16 -- -- --
4.00 < t < 5.00 0.15 0.17 0.19 -- -- --
5.00 < t < 6.00 0.17 0.20 0.23 -- -- --
6.00 < t < 8.00 0.17 0.22 0.25
1. Thickness is measured at any point located more than 15mm from the edge for slit edges and
25mm for mill edges - defined as Method B.
2. For strip and cut lengths < 30mm wide the thickness shall be measured at the centre of the strip.
3. Note the difference in the last two thickness bands compared to Method A.
Width tolerance
Provision is made in this standard for width tolerances for mill edges.
For wide strip and sheet/plate cut from wide strip with mill edges < 1000mm, the tolerance is +25/-0mm.
For wide strip with slit edges the tolerances are as in the table below:
Tolerances on wide cold rolled strip and sheet/plate cut from wide strip
Special tolerances (S)1)for
Normal tolerances for a specfied width w of
Specified a nominal width w of
thickness (t) w<12 125<w<250 250<w<600 600<w<1000 1000<w<210 w<12 125<w<250 250<w<600
5 </w </w </w 0</w 5 </w </w
+0.5/ +0.3/-
t < 1.00 +0.5/-0 +0.7/-0 +1.5/-0 +2.0/-0 +0.3/-0 +0.6/-0
-0 0
+0.7/ +0.4/-
1.00 < t < 1.50 +0.7/-0 +1.0/-0 +1.5/-0 +2.0/-0 +0.5/-0 +0.7/-0
-0 0
+1.0/ +0.6/-
1.50 < t < 2.50 +1.0/-0 +1.2/-0 +2.0/-0 +2.5/-0 +0.7/-0 +0.9/-0
-0 0
+1.2/ +0.8/-
2.50 < t < 3.50 +1.2/-0 +1.5/-0 +3.0/-0 +3.0/-0 +0.9/-0 +1.0/-0
-0 0
+2.0/
3.50 < t < 8.00 +2.0/-0 +1.2/-0 +4.0/-0 +4.0/-0 -- -- --
-0
1. By special agreement, products can be supplied with permissible undersizes on the nominal width.
In this case, the values in this table apply as the oversize plus undersize range. E.g. 1.20 mm thick,
700 mm wide could be ordered to +1.0/-0.5mm by agreement.
2. For material with edges re-cut by shearing, the tolerances on width may by agreement be
increased to 5mm
3. This table is similar to that in EN 10259 except that the highest nominal thickness is now 8.00mm.
Length tolerance
Length tolerances also have both 'normal' and 'special' tolerance ranges. 'Special' tolerance should be
specifically requested. Each range is proportional to the length of the sheet or cut length, with a minimum
tolerance at 2000mm length. Unlike the old standards, these tolerances apply for any length that can be
supplied, and across the whole thickness range.
All dimensions in mm
Flatness tolerance
The flatness tolerance of of strip, sheet/plate and cut length shall not exceed 10mm for normal cases and
7mm where a special tolerance (FS) is required for length < 3000mm and 12mm for normal cases and 8mm
where a special tolerance (FS) is required for length > 3000mm.
This is identical to the requirements of EN 10259.
a) For maximum deviation from a flat horizontal surface, with the product lying under its own mas on a flat
surface, the maximum deviation from flatness in the maximum distance between the lower surface of the
product and the flat horizontal surface.
b) To measure the flatness, the product shall be laid on an approximately flat surface. Deviation with respect
to flatness shall be taken as the greatest distance between the product and a straight edge placed upon it.
The straight edge should be either 1000 or 2000mm long. It may be placed on the product at any position
and in any direction. Only the position of the points of contact of product and straight edge shall be taken
into account.
Unless otherwise agreed, the choice of measurement methid is left to the manufacturer.
Edge waviness
For strip, the waviness of the edges, i.e. the ratio of wave height (h) to wave length (l) shall be max 0.03 for
all thicknesses.
This requirement does not apply to work hardened material or condition 2D.
Related Articles