Sie sind auf Seite 1von 6

December 16, 2013 [ARIOSH TRAINEE TEST.

PIPE DESIGN AND DRAFTING,OIL AND GAS TEST 2013/2014


ANSWER ALL 25 QUESTONS
(30minutes) 16/12/2013

1. Which of these is not a type of offshore structure


i. Fixed Platform
ii. Gravity extension
iii. Compliant towers
iv. SPAR

a) i only b) ii c) i & ii d) None of the above

2. Which of the following is a function of a wellhead


i. Used to inject water or gas back into the oil reservoir
ii. Used to control flow from the reservoir
iii. Used to separate oil from and sediments in the extraction process
iv. All of the above

a) i only b) iv c) i & ii d) None of the above

3. Gas from separators is usually recompressed before it is transported. True or False


__________
4. _______________ are also known as 'natural gas liquids' (NGL). They are used as raw materials
for oil refineries or petrochemical plants, and as sources of energy.
5. Natural gas liquids include
a) Tantalum b) Sulfur c) Propane d) Hydrogen
6. Write out these acronyms in full
i. FPSO _______________________________________
ii. PID _______________________________________
iii. GA _______________________________________
iv. API _______________________________________
v. SCADA _______________________________________
7. Which one of the options below is a part of the drilling rig
a) Wellhead b) Derrick c) Christmas tree d) All of the above
8. The pressure and temperature in oil wells generally increases with increasing depth. True or
False? _____________
9. In the drilling process, the mud serves several purposes as shown below except
a) Bring rock fragments up to the surface
b) Its fibrous particles attach to the well surface to bind solids
c) Supports the casing in the drilling process
d) Lubricate the drill pipe string and Cone
10. Which of these valves opens to the same inside diameter as the tubing and is not used to
control flow in a Christmas tree
a) Swab Valve b) Wing Valve c) Master Valve d) Check Valve
December 16, 2013 [ARIOSH TRAINEE TEST.]

11. Which of this Wells employs the use of Umblical


a) Dry Completion b) Top side c) Subsea d) Deepsea
12. Pig launchers and receivers must be connected as a part of the terminal equipment in a
a) Separator b) Pipe c) Utility System d) Pipeline

The schematic below shows the process of water treatment in a production facility. Use the
schematic to answer questions 14 to 16

13. Fill in the name of the unnamed equipment in the schematic below

a
. b

Fig. 1
a) ________________________________
b) ________________________________

14. A centrifugal separator that will remove oil drops from the water is called __________________
15. The function of the last Equipment in the Water treatment is to
a) Remove the remaining water droplets from the oil
b) Remove the remaining oil droplets from the water
c) Pump lean glycol into the water for purification
d) Transfer the oil for final water removal
16. Removing salt from oil is the work of which equipment __________________
17. Removal of remaining fractions of water from gas in gas plant is the function of
a) Reboiler b) Scrubber c) Separator d) Compressor
18. The part of a subsea pipeline linking the platform to seabed is called
a) Pig b) Riser c) Skid d) Pipe
19. Maintenance of the Well without killing the Well is called
a) Well Workover b) Well Intervention c) Well Interception d) Primary Recover
20. The Scrubber is to the Gas treatment what the ____________is to the Water treatment
a) Heat Exchanger b) Scrubber c) Separator d) Hydro cyclone
21. Separation/stabilization and electrical multiphase pumping may be necessary for Subsea Wells if
December 16, 2013 [ARIOSH TRAINEE TEST.]

i. Reservoir pressure is low


ii. Distance to main facility is long
iii. There are flow assurance problems

a) i b) ii & iii c) i & iii d) All of the above

22. Which of the following is not found in an umbilical


a) Hydraulic pipes b) Data Cable c) Electrical cable d) Mud lines
23. An elbow has a radius of 24inches. Which of the following statement is/are TRUE?
i. For a long radius elbow the nominal size will be 16inches .
ii. For a short radius the nominal size will be 24inches.
iii. The nominal size for a short and long radius elbow is 24inches
a) Statement 1 only b) Statement 2 only c) Statement 1 and 2 only
d) Statement 3 only

24. Which of the following is/are true?

i. x>y
ii. x<y
iii. y= 1/16
iv. y= 1/4
a) Statement 1and 2 only b) Statements 2 and 4 only c) Statements 1 and 4 only

d) None of the above

25. Which of the following is/are true?

i. Pipe 1/8 to 12 has an outside diameter greater than its nominal pipe length
ii. Pipe 14 and above has an outside diameter equal to its nominal pipe size
December 16, 2013 [ARIOSH TRAINEE TEST.]

iii. The method of sizing pipe maintains a uniform outside diameter while varying the inside
diameter.
a) Statements 1 and 2 only b) Statements 1 and 3 only c) All of the above

d) None of the above.

26. Schedules can be defined as

a) Nominal pipe size b) Pipe inside diameter c) Pipe wall thickness.

d) Cost of pipes in the market.

27. How many bolt holes does a 2 150# flange have?

a) 2 bolt holes b) 4 bolt holes c) 6 bolt holes d) 10 bolt holes.

28. What is the angular spacing between the bolt holes on the 2150# flange

a) 180 degrees b)90 degrees c) 60 degrees d)36 degrees

29. Which of these valves should be used for throttling?

a) Ball valve b) Globe valve c) Check valve d) Butterfly valve

30. Which of these valves prevents excessive pressure on a gas service line?

a) Check valve b) Gate valve c) Gas service valve d) Relief valve

31. A valve often used to ensure a unidirectional flow of fluid along a pipe is called what?

a)Choke valve b)Pneumatic actuated gate valve c)Check valve d)Hydraulic actuated gate valve

32. What type of flange measures the rate of flow of fluid through the piping system?

a. Blind flange b)Orifice flange c)Threaded flange d)Weldneck flange

33. The equipment designed primarily for the transfer of air, gases or liquids by way of re-pressurizing
them is called what?

a) Separator b)Compressor c)Pumps d) Exchangers

34. Identify the following symbol

a) Check valve b)Gate valve c) Control valve d)Butterfly valve

35. Identify the following symbol


December 16, 2013 [ARIOSH TRAINEE TEST.]

a) Check valve b)Gate valve c)Control valve d)Butterfly valve

36. The instruments abbreviation TRC means

37. The abbreviation LAL in instrumentation means

38. Which of these pair of valves fully opens or fully closes by a 90 degrees turn of its wrench?

a) Ball valve and butterfly valve b) Globe valve and check valve

c) Ball valve and globe valve d) Gate valve and ball valve

39. The fitting x above connecting the two pipes A & B is what?

a) Coupling b) Eccentric reducer c)Concentric reducer d) Target tee

40. Which of the following statements is/are true?

i. Screwed and socket weld fittings are normally reserved for installations using fittings 3 and
smaller
ii. Forged steel screwed and socket weld fittings are manufactured in 2 pressure classes-3000#
and 6000#
iii. Swages and plugs are manufactured with external threads

a) Statement 1 and 2 only b) Statements 2 and 3 only c)None of the above

d) All of the above

41. Which of the following statements is/are true?

i. Screwed and socket weld fittings can be placed one fitting directly in contact with the other
ii. Screwed fittings are manufactured with threads on the inside of the fitting
iii. Pipe nipples are used to facilitate the assembly of screwed and socket weld fittings

a)Statements 1 and 2 only b) Statements 2 and 3 only

c) None of the above d) All of the above

42. Which of the following statements is/are true about Screwed swages?
December 16, 2013 [ARIOSH TRAINEE TEST.]

i. They always have female(internal) threads at both ends


ii. They have functionality similar to reducers
iii. They can be used in screwed, socket-weld or but weld configuration
a) Statements 1 and 2 only b) Statements 2 and 3 only

c) None of the above d )All of the above

43. What is the meaning of BBE.

44. Which of the following pair can be used for making a branch connection?

a) Stub-in and Olet b) Olets and couplings c) Couplings and elbows d) Stub-in and
caps

45. Which of these is not a type of flange?

a) Reducing flange b) Slip-on flange c) Ball-joint flange d) Lap-joint flange

Das könnte Ihnen auch gefallen