Beruflich Dokumente
Kultur Dokumente
TABLE OF CONTENTS
PAGE
1. PRECAUTION AND NOTICES ------------------------------------------------------------------------------------- 1
1.1. SAFETY PRECAUTIONS ---------------------------------------------------------------------------------------- 1
1.2. PRODUCT SAFETY NOTICE ----------------------------------------------------------------------------------- 1
1.3. SERVICE NOTES-------------------------------------------------------------------------------------------------- 1
8. WIRING DIAGRAM--------------------------------------------------------------------------------------------------- 19
10/15/2008
JT229H1EJ Service Manual
1. PRECAUTION AND NOTICES
This monitor is manufactured and tested on a ground principle that a user's safety comes
first.However, improper use or installation may cause damage to the monitor as well as to
the user.Carefully go over the following WARNINGS before installing and keep this guide
handy.
WARNINGS:
This monitor should be operated only at the correct power sources indicated on the label
on the rear end of the monitor. If you're unsure of the power supply in your residence,
consult your local dealer or power company.
Use only the special power adapter that comes with this monitor for power input.
Do not try to repair the monitor your self as it contains no user-serviceable parts. This
monitor should only be repaired by a qualified technician.
Do not remove the monitor cabinet. There is high-voltage parts inside that may cause
electric shock to human bodies, even when the power cord is unplugged.
Stop using the monitor if the cabinet is damaged. Have it checked by a service technacian.
Put your monitor only in a clean, dry environment. If it gets wet, unplug the power cable
immediately and consult your service technician.
Always unplug the monitor before cleaning it. Clean the cabinet with a clean, dry cloth.
Apply non-ammonia based cleaner onto the cloth, not directly onto the glass screen.
Keep the monitor away from magnetic objects, motors, TV sets, and transformer.
Do not place heavy objects on the monitor or power cord.
Many electrical and mechanical parts in this chassis have special safety visual inspections
and theprotection afforded by them cannot necessarily be obtained by using replacement
components rated for higher voltages, wattage, etc. Before replacing any of these
components read the parts list in this manual carefully. The use of substitute replacement
parts which do not have the same safety characteristics as specified in the parts list may
create shock, fire, or other hazards.
1. When replacing parts or circuit boards, clamp the lead wires around terminals beforesoldering.
2. When replacing a high wattage resistor (more than 1W of metal oxide film resistor) in circuit
board, keep the resistor about 5mm away from circuit board.
3. Keep wires away from high voltage, high temperature components and sharp edges.
4. Keep wires in their original position so as to reduce interference.
5. Usage of this product please refer to also user's manual.
-1- 10/15/2008
JT229H1EJ Service Manual
2. SERVICE TOOL & EQUIPMENT REQUIRED
1. SIGNAL GEN.
2. MULTIMETER
3. OSCILLOSCOPE
4. SCREW DRIVER
5. IRON
6. ABSORBER
7. SOLDER
8. DUMMY LOAD (5ohm/200W)
3. SPECIFICATIONS
Viewing Angle CR 10
Horizontal: 170
Vertical: 160
-2- 10/15/2008
JT229H1EJ Service Manual
3.2. FACTORY SUPPORTING MODES
There are totally 35 timings mode that can be saved in memory by FIFO architecture.
This monitor can support VGA up to WSXGA+ resolution.
There are some resolution example listed in lookup timing table.
-3- 10/15/2008
JT229H1EJ Service Manual
DVI-D connector
-4- 10/15/2008
JT229H1EJ Service Manual
4.1 EXPLODED VIEW
-5- 10/15/2008
JT229H1EJ Service Manual
4.2. EXPLODED VIEW PARTS LIST
-6- 10/15/2008
JT229H1EJ Service Manual
5. BLOCK DIAGRAM
SWITCHING 12V
AC 110~220V
POWER SUPPLY
INPUT
I801 LD7575 5V
5V I102 ONBACKLITE I901 OZ9938GN
VGA-SDA DC / DC INVERTER
PANEL POWER
1.8V 3.3V
VGA-SCL 5V
R ADJBACKLITE
P101
VGA G
B LVDS BUS
D-SUB H-Sync I103
V-Sync TSUMU58EHJ PA [0,13]
SCALAR
R LCD PANEL
P102
G PB [12,21]
DVI
B
CLK
SDA I101
SCL 24LC02 I104 X101
DVI-5V FLSH 14.318MHz
3.3V
5V
-7- 10/15/2008
JT229H1EJ Service Manual
6. SCHEMATIC DIAGRAM
6.1. Input
P101
DB15 HD 6 L102 0/0603
11 1 R101 56 C101 1 2 0.047U RIN
7 L103 0/0603
12 2 R102 56 C102 1 2 0.047U GIN
8 L104 0/0603
13 3 R103 56 C103 1 2 0.047U BIN
9 PC5V
14 4 R104 NC/470 C104 1 2 NC/102P SOG
10 R107 R106 R105
4.7p/ESD
4.7p/ESD
4.7p/ESD
15 5
75 1% 75 1% 75 1%
D102
D103
D101
HSI
R108 100 C105 1 2 0.047U GNDR
VSI
R109 100 C106 1 2 0.047U GNDG
CLK_DDC
4.7p/ESD
R110 100 C107 1 2 0.047U GNDB
DAT_DDC
D107
VGA_CON
4.7p/ESD
4.7p/ESD
D104
5V D105
L101 120R 0805 I=300mA
R111 1K HSYNC
1
4.7p/ESD
NC C109 5V
1
C108
D108
1
D106
C165 R115 220pF
R116 NC 33pF R114 NC 2.2K
2
5V 1
2.2K
2
DET_VGA
2
3
0 OHM
VCC3V3
2
D109
1
C110
BAT54C
R118 R119 R120 0.1U
R117 R121 10K 4K7
2
10K 10K 4K7 I101 24LC02
8 VCC A0 1
P102 R122 100 DDCA_SCL R123 100 7 2
R124 100 DDCA_SDA WP A1 VCC3V3
6 SCL A2 3
DVI-D R125
5 SDA GND 4
Shell RX2- R- NC
RX2- 1
2 RX2+ R+
RX2+ R126 R127
GND 3
4 NC NC
RX4-
RX4+ 5
6 SCL R128 100 DDCD_SCL
SCL SDA R129 100 DDCD_SDA
SDA 7
VS 8
9 RX1- G- DVI5V
RX1- RX1+ G+ 5V
RX1+ 10
GND 11
12
D110
RX3-
D111
NC
NC
RX3+ 13
14 R130 1K R131
5V 10K
GND 15
16 HP
HP
RX0- B- 5V R132 100 DET_DVI
D112 0.01UF
RX0- 17
18 RX0+ B+
RX0+
GND 19
RX5- 20
RX5+ 21
R133
0.01UF
GND 22
D113
23 RXC+ CLK+ R187 NC 5V
RXC+ RXC- CLK- NC
RXC- 24
RED C1
GRN C2
C3 R183
BLU 10K
HS C4
3
MMBT3904
2
-8- 10/15/2008
JT229H1EJ Service Manual
6.2. Dc to Dc
5V 5V
R134
5V NC R135
10K
5V
12V
R138 0
R137 100
R186 VCC3V3
5V
3
NC/10K Q102 NC
P103
C111 + C112 1 R139 I107
NC adj_BACKLIGHT
1 102P
2 3 VIN VOUT 2
NC/MMBT3904 5V
2
3 VCC1V8
4 1 ADJ C117
5 R140 100 C113
6 R141 AMC1117-18 47uF/16V 0.1U
7 10K
8 C114
9
3
CON9 C115 C116 103P Q103
1 R185 NC/4.7K
103P 103P on_BACKLIGHT
NC/MMBT3904
2
5V DVI5V PC5V
DVI5V PC5V
VLCD
5V
1
R144
47K
R145 220
D116
Q104 D117
3
R146 1K BAT54C
on_Panel Q105 AP2305 SS14
1
R147 5V
3
MMBT3904 10K
2
C118 +
10UF/16V
I102 VCC3V3
3 2 VCC3V3
VIN VOUT
1 ADJ
C166 C119 C120 C121
AMC1084-33
47uF/16V 0.1U 47uF/16V 0.1U
-9- 10/15/2008
JT229H1EJ Service Manual
6.3. Scaler
VDDP_33
AVDD_33 AVDD_18 VCC3V3 VDDP_33
VDDC_18 MEMPLL_33 L105
VCC3V3
200 ohm/L0805/2A
104
126
114
107
112
C139 + C122 C123 C124 C125 C126 C127 C128 C129 C130 C131 C132
14
20
53
74
21
58
54
40
59
87
8
I103
103 10uF 0.1U 0.1U 0.1U 0.1U 0.1U 0.1U 0.1U 0.1U 0.1U 0.1U 0.1U
VDDC
VDDC
VDDC
VDDC
AVDD_33
AVDD_33
AVDD_33
AVDD_MEMPLL
VDDP
VDDP
VDDP
VDDP
VDDP
VDDP
AVDD_18
VDDP
VCTRL
GPIO_P14/PWM0 2
VCC3V3 R152
I104 36 DET_VGA 10K R154
MX25L4005AMC-12G GPIO_P22/PWM1 10K
GPIO_P24/PWM2 51
8 Q106
VDD SDO 2 41 SDO
2
7 MMBT3906 Q107
HOLD# CE# 1 42 CSZ GPIO_P04 73
2
C148 3 R155 4.7K MMBT3906
+ R153 WP# SCK 6 43 SCK GPIO_P25 109 1
R156 4.7K
4 VSS SDI 5 44 SDI 1
C149 0.1U 10K R157 100 LED_G
10uF on_BACKLIGHT R158 100 LED_A
3
GPIO_P00/SAR0 119
3
GPIO_P01/SAR1 120
WP 121 on_PANEL
GPIO_P02/SAR2 AUDIO_STBY
108 RST GPIO_P03/SAR3 122
123 HDCP_SDA R191 NC
GPIO_P06
2
14.318MHz
D118 127 C152
1N/LL4148 XOUT
C151 22P R161 R162 NC/0.1U
NC/3.3K NC/3.3K
102 I105 NC/24C16
C153 BYPASS
8 VCC A0 1
7 WP A1 2
KC01
VDDP_33 0.1U 39 R163 NC/100 6
I2C_MCL R164 NC/100 SCL A2 3 SOFTWARE
I2C_MDA 38 5 SDA GND 4
R165 NC HDCP KEY CODE
37 MODE
VCC3V3
VCC3V3
NC 55
R166 56
NC C154
NC 57
10K R167 R168
NC/3.3K NC/3.3K NC/0.1U R171 R172 R173 R174 R175
10K 10K 10K 10K 10K
I106 NC/24C04
8 VCC A0 1 P104
7 WP A1 2
HDCP_SCL R169 NC/100 6
HDCP_SDA R170 NC/100 SCL A2 3 2 R177 100
5 SDA GND 4 1 SELECT
VDDP_33 DOWN R176 100 2
UP R178 100 DOWN
3 UP
60 1 R179 100 4
VDDP MENU
VDDP 65 5 GND
LED_A 6
LED_G LED_AMBER
VDDP 66 7 LED_GREEN
71 POWER R180 100 8
VDDP VCC3V3 LCD_ONOFF
9 VCC3V3
10 MUTE
11 GND
C155 C156 C157 C158 C159 C160 C161
C168 220P 220P 220P 220P 220P 220P 220P
NC/0.1UF JST-PH11P-2.0-180
WP 45
2 GPIO_P47
46 GPIO_P46
DOWN 47
UP GPIO_P45
48 GPIO_P44
1 49 61
MUTE GPIO_P43 NC
50 GPIO_P42
POWER 55 62
GPIO_00 GND
GND 63
VCC3V3
NC 64
R193
NC/10K
NC 70
GND 69
GND 68
MUTE R194 NC/100
NC 67
C167
NC/220P
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
113 GND
118 NC
NC
NC
NC
NC
NC
101
105
106
110
111
115
116
117
11
17
29
52
72
88
1
-10- 10/15/2008
JT229H1EJ Service Manual
6.4. Panel Interface
VLCD
PA[0..9]
PA[0..9] PA0 LVA3P
PA1 LVA3M
VLCD
PA2 LVACKP
PA3 LVACKM
PA4 LVA2P
PA5 LVA2M
PA6 LVA1P
PA7 LVA1M C163
PA8 LVA0P C162 P105
PA9 LVA0M 100uF/16V 0.1U
1
PB[0..9] 2
PB[0..9] PB0 LVB3P 3
PB1 LVB3M VCC3V3 4
PB2 LVBCKP VCC_TEST&ODCTRL 5
PB3 LVBCKM 6
PB4 LVB2P RXEIN3+ LVA3P 7
PB5 LVB2M R181 NC RXEIN3- LVA3M 8
PB6 LVB1P RXECKIN+ LVACKP 9
+3V3 10
PB7 LVB1M RXECKIN- LVACKM
PB8 LVB0P RXEIN2+ LVA2P 11
PB9 LVB0M RXEIN2- LVA2M 12
13
R182 NC RXEIN1+ LVA1P 14
RXEIN1- LVA1M 15
16
RXEIN0+ LVA0P 17
RXEIN0- LVA0M 18
RXOIN3+ LVB3P 19
RXOIN3- LVB3M 20
RXOCKIN+ LVBCKP 21
RXOCKIN- LVBCKM 22
23
RXOIN2+ LVB2P 24
RXOIN2- LVB2M 25
RXOIN1+ LVB1P 26
RXOIN1- LVB1M 27
RXOIN0+ LVB0P 28
RXOIN0- LVB0M 29
30
CON30
-11- 10/15/2008
JT229H1EJ Service Manual
6.5. Key Pad
P701
2_SELECT 1
DOWN 2
UP 3
MENU 4
GND 5
LED_AMBER 6
LED_GREEN 7
LCD_ONOFF 8
1
JST-PH8P-2.0-180 1 1 1 1 1
D701
-12- 10/15/2008
JT229H1EJ Service Manual
6.6. Inverter
C924 P901
56p 3KV
L901 1
12V jumper Q904
R919 D902 R922 D903 AM4502 2
5.1K RLZ5.6B 5.1K RLZ5.6B C921
4 5 6(7) 7(8) 12P,3KV C925 P902
ON_OFF 5(6) 56p 3KV
R920 100 3 6 4 1
5V 3
C922
2 2
C928 2 7 1 8(9) 12P,3KV
Brightness + NC C914 D904 T902
1N4148 C920 1 8 T901 1 4
0.047U R923 100
+
GND R921 100
470uF/16V
C918 Q905 2 3
C915 D906 AM4502 C923
D905 1N4148 5P,3KV 200mH
OFF 1N4148 0.047U 0.1U 4 5 R951
R924 100 R943 3M 3KV/1W T903
3 6 51K F 1 4
ON
R913
22 D907 2 7
1N4148 2 3
1 8 R944 C916 C929
16.5K 200mH
4700pF NC C926 P903
56p 3KV
1
C927 P904
R903 R906 R910 R911 R912 C905 R953 56p 3KV
NC 100K I901 10K 100K 0ohm
11K F 2.2uF 1
1 DRV1 PGND 16 2
2 15 R942 2.49K
C902 R904 VDDA DRV2
R901 2.2uF 10K 3 14
10K TIMER AGND
OZ9938
4 13 C910
DIM CT 220pF D915
R905 1M 5 12 1N4148
ISEN SST C909
C903 102PF 6 11 1000P D914
VSEN LCT 1N4148
R907 75K 7 10 C907
OVP ENA NC D913 R928 1M
8 9 1N4148
C901 R902 NC1 NC2 R945
0.01uF NC C917 NC 18K D912 R927 1M
1N4148
R909 NC C906 C908
D911 R926 1M
0.01uF 0.033uF 1N4148
D910 R925 1M
1N4148
R915 D909
511 F 1N4148
C904 R908
R947 C911 C919 0.039UF 357 F D908
1M 330P 100p HZ12
R918
NC
R932 R931 R930 R929
10K 10K 10K 10K
R916 Q902 Q903
3
JT229D1EJ-300
7 9
-13- 10/15/2008
JT229H1EJ Service Manual
6.7. Power
C823
R830 22 2WS 1000PF/1KV Brightness
! L802
1 T801 10 1 5.2uH
!
3 D804 ON_OFF
D801 C816 2 FCQ10A15
GBU4K 100uF/400V
! C817 + C827 + C828 C829 +
+ 1
1000uF/16V
1000uF/16V
R832 1000PF/1KV C822 Z804
470uF/16V
+
R805 56K/1WS R827 1000PF/1KV
P802
7
511K F 47 P6KE10A
D802 R828 9
2 3 8
UF4007 47
R808 L804 7
3 6
R806 10K 3Ts 6*10 6.7 1
-
511K F 5
4 3 4
R825 R826
4
2 3
C805 + C819 D803 100 100
UF4004 D805 FCQ10A06 2
5 8.9 1
0.1U 22UF/50V
R804
! D806 NC F802
750K
! ! C820
5.1V
I801 R809 33 Q801 4700pF
2
R803 2SK4100 D807 NC L803 JUMPER 12V
!
8
5
750K R807 5.2UH
511K F 1
NC
Vcc
Drv
HV
Z803
LD7576 RLZ22 C824 C825 C826
3
+ + +
1000UF/16V
1000UF/16V
L805 R833
470uF/16V
!
GND
ET24 52mH R813 R812 R829 NC
Adj
CS
FB
330R
! 330R
! NC
3 2
1
! ! R810
!
4 1
C815 C814 C804 10K R831
NC NC C801 0.47R/ 2WS
L807 470P
3TS 6*10 0.047U
Z802
L806 C803 R815 HZ15
3Ts 6*10 270
2200P
!
C810 C802 I802 R817 R819 R822
0.47uF
! TLP621 100
NC R814 4 1 3.65K F 39.2K F R823
R816 NC
0 1K R824 C806 R837
F801
! 0R 0.1U NC/2W
T2.5AL/250V 3 2 R818
! 1K R820 Z801
R802 1.3K F
3
10ohm 4A C821 + NC
I803 Q802 1
C830 10UF/50V TL431D R821 NC
1.21K F
220P C831
2
220P
1
!
JT229D1EJ-300
FG
N
L
P801
0711-2-PL4M20-C
-14- 10/15/2008
JT229H1EJ Service Manual
7. WORKING THEOREM
A. DC-DC CONVERTER
This brick convert is the 110-220AC input voltage to 12V AND 5V output for invert use and panel
use and system controller use .
5V Out put at L803
VCC 12V In put at L802
B. Scaling controller
The ADC is to convert RGB analog signal to digital signal that scaling chip can acknowledge.
The HSYNC input receives a logic signal and provides the frequency reference for pixel clock
generation.
The scaling IC is to converts the input signal ranging from VGA to SXGA into UXGA resolution
that panel can acknowledge.
GENERAL DESCRIPTION
The TSUMU58EHJ is total solution graphics processing IC for LCD monitors with panel
resolutions up to UXGA.It is configured with a high-speed integrated triple-ADC/PLL, an
integrated DVI receiver,a high quality display processing engine, an RTE engine for response-time
enhancement, an integrated micro-controller and output display interface that can support LVDS
panel interface format.To further reduce system costs, the TSUMU58EHJ also integrates
intelligent power management control capability for green-mode requirements and
spread-spectrum support for EMI management.
The TSUMU58HJ incorporates the worlds first coherent oversampled RGB graphics ADC in a
monitor controller 1 system.The oversampling ADC samples the input RGB signals at a frequency
that is much higher than the signal source pixel rate.This can preserve details in the video signal
that ordinarily would be lost due to input signal jitter or bandwidth limitations in non-oversampled
systems. 2 The TSUMU58EHJ also incorporates a new Dynamic Frame Rate (DFR) generator
for the digital output video to the display panel that preserves the advantages of a fixed output
clock rate, while eliminating the output end of
frame short-line.
PIN DESCRIPTION
Analog Interface
Pin Name Pin Type Function Pin
Schmitt Trigger Input
HSYNC0 Analog HSYNC input 32
w/ 5V-tolerant
Schmitt Trigger Input
VSYNC0 Analog VSYNC input 33
w/ 5V-tolerant
REFP Internal ADC top de-coupling pin 31
REFM Internal ADC bottom de-coupling pin 30
RIN0P Analog Input Analog red input 28
RIN0M Analog Input Reference ground for analog red input 27
SOGIN0 Analog Input Sync-on-green input 26
GIN0P Analog Input Analog green input 25
GIN0M Analog Input Reference ground for analog green input 24
BIN0P Analog Input Analog blue input 23
BIN0M Analog Input Reference ground for analog blue input 22
REXT External resistor 390 ohm to AVDD_33 7
-15- 10/15/2008
JT229H1EJ Service Manual
DVI Interface
Pin Name Pin Type Function Pin
RX0N DVI Input DVI Data Channel 0 Negative Input 16
RX0P DVI Input DVI Data Channel 0 Positive Input 15 15
RX1N DVI Input DVI Data Channel 1 Negative Input 13
RX1P DVI Input DVI Data Channel 1 Positive Input 12
RX2N DVI Input DVI Data Channel 2 Negative Input 10
RX2P DVI Input DVI Data Channel 2 Positive Input 9
RXCKN DVI Input DVI Clock Channel Negative Input 19
RXCKP DVI Input DVI Clock Channel Positive Input 18
LVDS Interface
Pin
Pin Name Function Pin
Type
LVA0M Output LVDS A-Link Channel 0 Negative Data Output 86
LVA0P Output LVDS A-Link Channel 0 Positive Data Output 85
LVA1M Output LVDS A-Link Channel 1 Negative Data Output 84
LVA1P Output LVDS A-Link Channel 1 Positive Data Output 83
LVA2M Output LVDS A-Link Channel 2 Negative Data Output 82
LVA2P Output LVDS A-Link Channel 2 Positive Data Output 81
LVA3M Output LVDS A-Link Channel 3 Negative Data Output 78
LVA3P Output LVDS A-Link Channel 3 Positive Data Output 77
LVA4M Output LVDS A-Link Channel 4 Negative Data Output 76
LVA4P Output LVDS A-Link Channel 4 Positive Data Output 75
LVACKM Output LVDS A-Link Negative Clock Output 80
LVACKP Output LVDS A-Link Positive Clock Output 79
LVB0M Output LVDS B-Link Channel 0 Negative Data Output 100
LVB0P Output LVDS B-Link Channel 0 Positive Data Output 99
LVB1M Output LVDS B-Link Channel 1 Negative Data Output 98
LVB1P Output LVDS B-Link Channel 1 Positive Data Output 97
LVB2M Output LVDS B-Link Channel 2 Negative Data Output 96
LVB2P Output LVDS B-Link Channel 2 Positive Data Output 95
LVB3M Output LVDS B-Link Channel 3 Negative Data Output 92
LVB3P Output LVDS B-Link Channel 3 Positive Data Output 91
LVB4M Output LVDS B-Link Channel 4 Negative Data Output 90
LVB4P Output LVDS B-Link Channel 4 Positive Data Output 89
LVBCKM Output LVDS B-Link Negative Clock Output 94
VBCKP Output LVDS B-Link Positive Clock Output 93
-16- 10/15/2008
JT229H1EJ Service Manual
GPIO Interface
Pin Name Pin Type Function Pin
General Purpose Input/Output; 4mA driving
GPIO_P14/
I/O w/ 5V-tolerant strength/ Pulse Width Modulation Output; 2
PWM0
4mA driving strength
General Purpose Input/Output; 4mA driving
GPIO_P15 I/O w/ 5V-tolerant 3
strength
GPIO_P16 I/O w/ 5V-tolerant General Purpose Input/Output; 4mA driving 4
General Purpose Input/Output; 4mA driving
GPIO_P22/
I/O w/ 5V-tolerant strength/ Pulse Width Modulation Output; 36
PWM1
4mA driving strength
GPIO_P47- General Purpose Input/Output; 4mA driving
GPIO_P42 I/O w/ 5V-tolerant 45-50
strength
GPIO_P24/ General Purpose Input/Output; 4mA driving
PWM2 I/O w/ 5V-tolerant strength/Pulse Width Modulation Output; 4mA 51
driving strength
General Purpose Input/Output; 4mA driving
GPIO_P04 I/O w/ 5V-tolerant 73
strength
General Purpose Input/Output; 4mA driving
GPIO_P25 I/O w/ 5V-tolerant 109
strength
GPIO_P00/ General Purpose Input/Output; 4mA driving
SAR0 I/O w/ 5V-tolerant strength/ 119
SAR ADC Input
GPIO_P01/ General Purpose Input/Output; 4mA driving
SAR1 I/O w/ 5V-tolerant strength/ 120
SAR ADC Input
GPIO_P02/ General Purpose Input/Output; 4mA driving
SAR2 I/O w/ 5V-tolerant strength/ 121
SAR ADC Input
General Purpose Input/Output; 4mA driving
GPIO_P03/
I/O w/ 5V-tolerant strength/ 122
SAR3
SAR ADC Input
General Purpose Input/Output; 6/12mA
GPIO_P06 I/O w/ 5V-tolerant programmable 123
driving strength
General Purpose Input/Output; 6/12mA
GPIO_P07 I/O w/ 5V-tolerant programmable 124
driving strength
General Purpose Input/Output; 4mA driving
GPIO_P13/ I/O w/ 5V-tolerant
strength/ Pulse Width Modulation Output; 125
WM2 I/O w/ 5V-tolerant
4mA driving strength
Misc. Interface
Pin Name Pin Type Function Pin
BYPASS For External Bypass Capacitor 102
RST Input w/ 5V-Tolerant Chip Reset; High Reset 108
VCTRL Output Regulator Control 103
Chip Configuration Input; 10K 37
MODE input
ohm pull-low for normal operation
DDC Data for DVI interface; 4mA 5
DDCD_SDA I/O w/ 5V-tolerant
driving strength
DDCD_SCL Input w/ 5V-Tolerant DDC Clock for DVI Interface 6
DDCA_SDA/ I/O w/ 5V-tolerant DDC Data for Analog Interface; 34
-17- 10/15/2008
JT229H1EJ Service Manual
RS232_TX 4mA driving strength/UART
Transmitter/GPIO
DDCA_SCL/ DDC Clock for Analog Interface/ 35
Input w/ 5V-Tolerant
RS232_RX UART Receiver/GPIO
I2C Master Data; 4mA driving 38
I2C_MDA I/O w/ 5V-tolerant
strength
I2C_MCL I2C Master Clock; 4mA driving 39
I/O w/ 5V-tolerant
strength
XIN Crystal Oscillator Input Xin 128
XOUT Crystal Oscillator Xout 127
Output
Power Pins
Pin Name Pin Type Function Pin
AVDD_33 3.3V Power Analog Power 8, 14, 20
AVDD_18 1.8V Power Analog Power 21
AVDD_MEM 3.3V Power PLL Power
58
PLL
VDDP 3.3V Power Digital Output Power 40, 54, 59, 60, 65,
66, 71,
107, 112, 114
VDDC 1.8V Power Digital Core Power 53, 74, 104, 126
1, 11, 17, 29, 52,
62, 63, 68,
GND Ground Ground 69, 72, 88,
101, 105, 106,
113
No Connects
Pin Name Pin Type Function Pin
No Connect. Leave 55-57, 61, 64, 67, 70, 110, 111,
NC
These Pins Floating 115-118
INVERTER
In order to drive the CCFLs embedded in the panel module, there is a half bridge inverter to
convert by the controller.
The input 12V up to hundreds of AC voltage output.
The inverter is formed by symmetric in order to drive the separate lamp modules.
The input stage consists of a PWM controller, half bridge inverter, and switching MOSFET to
convert DC input into AC output.
The output stage consists of a tuning capacitor, coupling capacitor, transformer, push-pull
MOSFET pair to boost AC output up to hundreds of voltage.
And one resister is serial to lamp for output voltage feedback.
There are two signal to control the inverter which come from system.
Logic high level which send to I901 is turn on the inverter.
BRI signal control brightness by DC level which was integral from PWM signal.
-18- 10/15/2008
JT229H1EJ Service Manual
8. WIRING DIAGRAM
-19- 10/15/2008
JT229H1EJ Service Manual
9. PCB LAYOUT
9.1. MAIN PCB TOP VIEW
-20- 10/15/2008
JT229H1EJ Service Manual
9.2. MAIN PCB BOTTOM VIEW
-21- 10/15/2008
JT229H1EJ Service Manual
9.3. KEYPAD PCB TOP VIEW
-22- 10/15/2008
JT229H1EJ Service Manual
9.4. KEYPAD PCB BOTTOM VIEW
-23- 10/15/2008
JT229H1EJ Service Manual
9.5. POWER PCB TOP VIEW
-24- 10/15/2008
JT229H1EJ Service Manual
9.6. POWER PCB BOTTOM VIEW
-25- 10/15/2008
JT229H1EJ Service Manual
10. TROUBLE SHOOTING FLOW CHART
START
CHECK
MAIN
N
5V OK? CHECK Y CHECK
OK?
N
3.3V OK? CHECK Y CHECK
D807,I801,I801
I102, OK? I102 3.3V
N
1.8V OK? CHECK Y CHECK
D807,I801,I801
I107 OK? I107 1.8V
-26- 10/15/2008
JT229H1EJ Service Manual
10.1. NO POWER
5 V O/P PANEL
STAR I901 P901-P904
T801 PA
NE
12 V Check I901
Q905,Q904
Check
Q901,Q902
12 V 0/P Q903
C823
Y
D801 D806
,T901
C816 D807
Check
12 V
I801 MAIN
Q801 PCB
-27- 10/15/2008
JT229H1EJ Service Manual
10.2. NO DISPLAY
Y
Y
-28- 10/15/2008
JT229H1EJ Service Manual
10.3 LOSE COLOR
Some bits
Lose color
lost R or G or B
Y Y
N Check N
Check I103 I103 OR Check
P105
R-pack
soldering
Sign
Sign Cable
N
Check Check
I104 poor
soldering R108,R109.R110 C101,C102
C103,C107
R101,R102,R103 C105,C106
I103
fail or
Poor,,soldering
-29- 10/15/2008
JT229H1EJ Service Manual
11. ADJUSTMENT
(Fig.1)
(The data on this picture is a example only,the real one,please refer to your monitor.)
-30- 10/15/2008
JT229H1EJ Service Manual
F. Adjust Color Temperature:
(1) EEPROM INIT(5BLOCKS):
Press key move cursor to EEPROM INIT, Press 2 key then monitor will
INIT ADC value
(2) Press key move cursor to White Balance, Press 2 key do white balance
adjustment.
(3) Press key move cursor to Color Temerature Adjust, Press 2 key, Then
OSD will display (Fig.2)
(Fig.2)
(The data on this picture is a example only,the real one,please refer to your monitor.)
(4) 9300K verify: move cursor to Cool R or G or B Press 2 key,
Press , key adjust R.G.B value
x=0.283 0.03
y=0.298 0.03
Press 1 key return to Fig.2
(5) 6500K verify: Repeat (4) press , move cursor to Normal R or G or B
press 2 key
x=0.313 0.03
y=0.329 0.03
Y250 cd/m2
(6) 5400K verify: Repeat (4) press , move cursor to Warm R or G or B
press 2 key
x=0.332 0.03
y=0.348 0.03
(7) Press 1 key go back to Fig.2, Then press 1 key return to Fig.1, Power key
OFF/ON quit factory mode.
G. Color Temperature & Luminance Verify:
(1) BRIGHTNESS default, CONTRAST default
9300K: x=0.283 0.03 y=0.298 0.03
6500K: x=0.313 0.03 y=0.329 0.03
5400K: x=0.332 0.03 y=0.348 0.03
(2) BRIGHTNESS MAX, CONTRAST MAX, Color Temperature 6500K
Y 250 cd/m2
2. Geometry:
(a). Set cross-hatch pattern and preset timing as timing table listed.
(b). Change to each mode in turn and wait for the monitor finish auto-alignment and save
process before change to next mode.
(c). Until all of modes are agjusted, exit OSD menu and press PWR OFF to exit factory
mode.
-31- 10/15/2008