Beruflich Dokumente
Kultur Dokumente
FIRE
ALARM
E.O.L
3K3
ANCILLARY 4K7
SERVICES MANUAL CALL
ANALOGUE DETECTORS POINT ( MCP )
EXTERNAL
COMMUNICATION ION OPTICAL HEAT PRESS HERE
LOOP TO BREAK
ISOLATOR
FIRE
ALARM
FIREFIGHTER FACILITY POWER ON
PRE-ALARM
ALARM
FAULT
OUTPUT ISOLATE SENSOR
JKL
4 5
MNO
6
PQRS 4K7 NO SOUNDER
AUXILIARY
FAULT / ISOLATE
ZONE 7 8 9
NC
RELAY
AIF
ACTIVE
DISPLAY
TUV
TO
WXYZ
0
SYMB
NO
RELAY MONITORED
IN-3 NC
AS PER INPUT 1 O/P 3 INPUT
ISOLATOR C3
+
4K7
+ +24V DC +24V DC
-
PRESS HERE
TO BREAK
-
FIRE
ALARM
E.O.L SPECIFICATIONS:
6K2 MAX LENGTH = 2KM
MAX RESISTANCE = 50ohms
MIN CABLE SIZE = 1.5mm²
Typical Application
BASIC CONFIGURATION
Main Board Main CPU
The Main Board is the " heart " of the FACP and The Main CPU holds the main central processing
carries the devices for interconnecting to all the unit for the FACP.
other Boards, a buzzer for auditory indication, the
backlight power supply for the LCD and CPU Slave CPU
Reset. The Slave CPU (Central Processing Unit) provides
the interfacing signals and I/O’s required to allow
The Main CPU is mounted on and connected to the FACP to connect / communicate to a variety of
this board which provides interfacing to termination boards.
+ Note: If the LCD operates in a redundant path Communications: Controller Interface Card
mode the total cores including power is 10. The The Controller Interface Card ( CIC ) provides 1 X
preferred cabling method in this case is 1 X 2 pair RS232 O/P for High Level Interfaces, Graphics
twisted shielded cable (4 core) and 1 X two pair etc., 1 X half duplex RS485 O/P for external LED
twisted shielded cable (4 core) plus 2 core power Mimic Boards, EWIS and to allow for multiple CIC
interconnection
LED Mimic ( RS485 )
Two core twisted shielded cable (No return loop) Product Data Sheet
plus 2 core power or local supply. Controller Interface Card PDS159-0054
Minimum Requirements
Computer ü Pentium II 400Mhz, 64M RAM,
(Rec Min)
ü 2 GIG Hardrive, CDROM
ü Serial Comms for mouse or
touch screen interface
GRAPHICS
ü Parallel Comms port for
SmartGraphics is a purpose built graphics hardware security key / printer
product for the monitoring of the Ampac ü Serial Comms port for
FireFinder™ FACP. connection to FACP, RS232 or
RS485 as required
Features
ü Windows 98, 2000, NT, XP
ü Remote control of the fire system
ü Display status of devices, zones and Monitor 17” min (resolution 1024 x 768)
network nodes 1 pair twisted & screened
RS232 Comms
ü Supports user defined maps 15m maximum from FireFinder™
ü Security / password protection Baud rate – 9600 to 38400
ü Option for mouse driven, touch screen
interface or other pointing devices RS485 Comms 1 pair twisted & screened
ü Operates using industry standard 1200m maximum from FireFinder™
ModBus protocol Baud rate – 9600 to 38400
ü Event and user access logs
ü User may embed photographs. Supports Product code 159-0073 License package only
passive symbols eg, fire extinguishers, 159-0074 Complete system package
hose reels, hydrants etc.
ü Key map helps user to navigate
Product Data Sheet
throughout the site
PDS159-0067
+ Note # 1 : This comprises 4 on the Main Controller and 4 on the Expansion Board.
+ Note # 2 : Depends on the configuration and the number of Panels in the System.