Beruflich Dokumente
Kultur Dokumente
Extension drilling 13
Reaming equipment 59
Shank adapters 63
Auxiliary tools 99
Grinding 105
Copyright
AB Sandvik Tamrock Tools
Sandviken
This product catalogue is a presentation of
Sandvik Rock Drilling Tools manufactured by
Sandvik Tamrock Tools Group.
Note that all bits are bigger on diameter than the given measurements in the catalogue.
Button bits: Are max 3,0 mm larger for some designs in order to make up for fast initial
wear on the diameter. The minimum diameter is 1,5 mm above given measurement.
Keep in mind that a bit always gives a bigger hole than the stated bit diameter.
The oversize of the hole is depending upon rock conditions, and can be as much as 3-4 mm.
Note! Products marked in bold figures are standard products stocked in Sweden.
Other products are offered on request. See also pages 57 and 138.
Integral drill steels and
Tapered equipment
CONTENTS Page
Integral steels with reduced width of bit (small gauge steel) ................................................................................................... xxx-xxxx-50
Integral steels with reduced width of bit, + tolerance (small gauge steel)................................................................................. xxx-xxxx-5005
Integral steels, Premium plus, H22, insert height 19 mm ........................................................................................................ xxx-xxxx-65
Shank rod, drilled for flushing tube 4.5-5 mm, packing .......................................................................................................... xxxx-xxxx-13
Tapered rod, drilled for flushing tube 4.5-5 mm, carburized.................................................................................................... xxxx-6xxx-11
Tapered rod, drilled for flushing tube 4.5-5 mm, HF- hardened............................................................................................... xxxx-11xx-11
Tapered button bits, cemented carbide grade MP 45 with ballistic buttons.............................................................................. xxxx-xxxx-B45
5
Integral drill steels
H19 (3/4) and Threaded integrals
Dimensions Part No.
L D
Series mm ft in mm in
Shank 19 x 108 mm (3/4"x 4 1/4")
A B 21 400 1' 4" 29 19/64" 724-0429
800 2' 7" 28 1 7/64" 724-0828
1-1_6
1600 5' 3" 27 1 1/16" 724-1627
108 2400 7' 10" 26 1 1/32" 724-2426
L
A B
24 600 2' 27 1 1/16" 724-0627
19 19
D 1200 3' 11" 26 1 1/32" 724-1226
1-1_1
L D
1-1_1
L D
L D
6
Integral drill steels
H22 (7/8")
Dimensions Part No.
L D
Series mm ft in mm in
Shank 22x108 mm (7/8" x 4 1/4")
A B 11 800 2' 7" 34 1 11/32" 714-0834-65
1600 5' 3" 33 1 19/64" 714-1633-65
1-1_6
2400 7' 10" 32 1 1/4" 714-2432-65
108 3200 10' 6" 31 1 7/32" 714-3231
L
A B 4000 13' 1" 30 1 3/16" 714-4030
19 19
4800 15' 9" 29 1 9/64" 714-4829
D 5600 18' 4" 28 1 7/64" 714-5628-50
6400 21' 27 1 1/16" 714-6427-50
7200 23' 8" 26 1 1/32" 714-7226-50
7
H22 Tapered equipment
Taper 12
Tapered rod
Cross bit
Button bit
1x4 1x6 1x7 4x7 30 26 1 1/32" 7795-6426-B45
2-1_466
Button bit
2x4 1x4 2x7 5x7 40 32 1 1/4" 7795-4432-B45
2-1_465
Button bit
1x4 1x6 2x7 5x7 35 33 1 9/64" 7770-4433-B45
2-1_394 B
Cross bit
1x4 2x4 28 1 1/8" 7770-9028-42
2-1_393
Tapered rod
Button bit
Button bit
1x5.5 1x4 1x7 4x8 35 32 1 1/4" 7776-6432-B45
2-1_466
Button bit
1x4 1x6 2x7 5x7 40 32 1 1/4" 7776-4432-B45
2-1_465
9
H22 Tapered equipment
Taper 7
1-1_28
Tapered rod
Button bit
Cross bit
10
Stone working tools
Plug hole integral steel
9-1_32
Shank rod
Cross bit
82.5 L
D 45 1 3/4" 7732-1045-42
11
Extension drilling
Page
CONTENTS Code information ............................................................ 15
Button bits, cemented carbide grade MP 45, with spherical buttons ....................................................................................... xxxx-xxxx-S45
Button bits, cemented carbide grade MP 45, with ballistic buttons ......................................................................................... xxxx-xxxx-B45
Button bits, cemented carbide grade DP 65, with spherical buttons ....................................................................................... xxxx-xxxx-S65
Button bits, cemented carbide grade DP 65, with semi-ballistic buttons ................................................................................. xxxx-xxxx-R65
Button bits, cemented carbide grade MP 45, with semi-ballistic buttons ................................................................................ xxxx-xxxx-R45
15
Extension drilling
R22 (7/8")
Shank rod
2-1_395
D
L
16
Extension drilling
R23 (29/32")
MF-rod
Cross bit
Shank adapter
2-1_502A
Shank rod
Button bit
L D Part No.
mm ft in mm in
MF-rod, R23 - Hex 22 - R23
2095 6' 10 1/2" 22 7/8" 7857-4821-20
2-1_ 314
17
Extension drilling
R25 (1")
Shank rod
Button bit
2-1_397
Coupling
Shank adapter sleeve Extension rod
Cross bit
Cross bit
1x5 2x5 45 1 3/4" 7732-1045-42
1x5 2x5 51 2" 7732-1051-42
2-1_3
22 R25 Packing
108 L 795-1831
Flushing hole 6.7 mm for flushing tube 4.5 - 5.0 mm
Packing
25 R 25
D 795-1811
159 L
Flushing hole 8.6 mm for flushing tube 8 mm
18
Extension drilling
R25 (1")
Dimensions Part No.
L D
mm ft in mm in
Extension rod, R25 - Hex 25 - R25
915 3' 25 1" 7852-2309-20
2-1_ 5
1220 4' 25 1" 7852-2312-20
1525 5' 25 1" 7852-2315-20
R 25 D R 25 1830 6' 25 1" 7852-2318-20
L 2435 8' 25 1" 7852-2324-20
Flushing hole 8.6 3050 10' 25 1" 7852-2331-20
R 25 D Thread
L
Wrench flat 38 mm
Shank adapter
See page 63
19
Extension drilling
R28 (1 1/8")
MF-rod
Button bit
2-1_398
Coupling
Shank adapter sleeve Extension rod
Cross bit
1)
D 1) 1x5 1x6 2x8 5x9 35 41 1 5/8" HMCA 7739-5241-S45
1x5 1x6 2x8 5x10 35 43 1 11/16" HMCA 7739-5243-S45
1)
D
R 28 D R 28
L
Flushing hole 9.3 mm.
Female end OD 41.5 mm.
R 28 D R 28
L
Flushing hole 8.8
20
Extension drilling
R28 (1 1/8")
Dimensions Part No.
L D
mm ft in mm in
Bit adapter coupling, R28-Thread
Thread
R25 235 9 1/4" 40 1 37/64" 7839-2301
R32 230 9 1/16" 40 1 37/64" 7839-3301
2-1_215
R 28 D Thread
L
Wrench flat 38 mm.
R 28 Thread
L
Shank adapter
See page 63
21
Extension drilling
R32 (1 1/4")
Coupling sleeve Extension rod Guide tube
Button bit
Button bit
2-1_487
Button bit
2x9.0 4x10 8x10 30 64 2 1/2" HMCVA 7733-2664-S45
2-1_22
Button bit
1) 2x9 6x10 8x11 35 76 3" HMCVA 7733-2676-S45
2-1_486
Cross bit
1x5 2x7.5 51 2" 7733-1451-42
1x5 2x7.5 57 2 1/4" 7733-1057-42
2-1_23
Guide bit
1x6 2x7.5 4x8 51 2" 7733-8251-86
2-1_46
22
Extension drilling
R32 (1 1/4")
Dimensions Part No.
L D
Bit dia, mm mm ft in mm in
Guide Tube
51-64 1830 6' 46 1 3/4" 7953-4618-20
51-64 3050 10' 46 1 3/4" 7953-4631-20
2-1_425
R 32
R 32 D
L
Female end OD 46 mm.
R 32 R 32
L
Shank adapter
See page 63
23
Extension drilling
R32 (1 1/4")
Dimensions Part No.
L D
mm ft in mm in
Extension reaming equipment, Pilot adapter for 51 mm (2") pilot hole
Thread
2-1_126
R32 47 1 7/8" 7823-3647
T D
24
Extension drilling
T35(1 3/8") bit thread
2-1_545
T 35 D T 35
L
25
Extension drilling
T38 (1 1/2")
Coupling
sleeve Extension rod Guide tube
Button bit
Button bit
Retrac
2-1_488
MF-rod MF-rod
Shank adapter X-bit
Cross bit
Coupling Coupling Retrac
sleeve Extension rod sleeve Extension rod Pilot Guide bit
adapter
Reaming bit
Bit adapter
coupling
Button bit
3x7 3x11 6x12 30 64 2 1/2" HMCVA 7514-3864-S45
3x7 3x11 6x12 30 64 2 1/2" HMCVA 7514-3864-S65
2-1_323
Button bit
3x9 4x11 7x12 35 76 3" HMCVA 7514-3876-S45
3x9 4x11 7x12 35 76 3" HMCV 7514-3876-S65
2-1_324
26
Extension drilling
T38 (1 1/2")
Flushinghole, mm Buttons, mm Dimensions Bit Part No.
Front Gauge Front Gauge D classi-
No Size No Size No Size No Size Angle mm in fication
Button bit, Retrac
2x11 6x10 8x10 35 70 2 3/4" HMCFVA 7514-7870-S45
2x11 6x10 8x11 35 76 3" HMCFVA 7514-7876-S45
2-1_491
X-bit
1x7.5 2x7.5 64 2 1/2" 7514-4064-11
1x7.5 2x7.5 76 3" 7514-4076A-11
2-1_41
Guide bit
1x9 2x9 4x9 64 2 1/2" 7514-8264-86
2-1_46
2-1_47
3050 10' 39 1 1/2" 7324-4331C-30
T 38
3660 12' 39 1 1/2" 7324-4337C-30
T 38 D
L
Flushing hole 14.5 mm. Wrench flat 32 mm.
Coupling sleeve
191 7 1/2" 55 2 5/32" 7314-3355
2-1_227
T38 T38
L
Shank adapter
See page 63
T D
28
Extension drilling
R38 (1 1/2")
Button bit
2-1_401
Coupling
Shank adapter sleeve Extension rod
X-bit
X-bit
1x7.5 2x7.5 70 2 3/4" 7734-4070-11
2-1_41
Coupling sleeve
170 6 11/16" 55 2 5/32" 7994-3655
2-1_228
Thread
R 38 D
L
Wrench flat 44.5 mm.
29
Extension drilling
R38 (1 1/2")
Dimensions Part No.
L D
mm ft in mm in
Reduction coupling, R38 - Thread
2-1_232 Thread
D R32 170 6 3/4" 55 2 5/32" 7994-3455
T38 185 7 9/32" 55 2 5/32" 7314-4455
T45 220 8 21/32" 63 2 31/64" 7315-4463
R 38 Thread
L
Shank adapter
See page 63
30
Extension drilling
T45 (1 3/4")
Coupling
sleeve Extension rod Guide tube
Button bit
Button bit
2-1_493
Bit adapter
coupling
Button bit
3x10 6x10 9x11 40 89 3 1/2" MSCAN 7515-2689-B45
3x10 6x12 9x12 35 102 4" HMCVA 7515-2602-S45
3x10 6x12 9x12 35 102 4" HMCV 7515-2602-S65
2-1_495
Button bit
3x9 4x11 7x12 35 76 3" HMCVA 7515-3876-S45
3x9 4x11 7x12 35 76 3" HMCV 7515-3876-S65
2-1_324
Button bit
2x13 6x13 8x13 35 89 3 1/2" HMCVA 7515-3889-S45
2x13 6x13 8x13 35 89 3 1/2" HMCV 7515-3889-S65
2-1_496
31
Extension drilling
T45 (1 3/4")
Flushinghole, mm Buttons, mm Dimensions Bit Part No.
Front Gauge Front Gauge D classi-
No Size No Size No Size No Size Angle mm in fication
Button bit, Retrac
3x10 6x10 9x11 35 89 3 1/2" HMCFVA 7515-7889-S45
3x10 6x10 9x11 35 89 3 1/2" HMCFV 7515-7889-S65
2-1_498
Guide bit
1x12 2x10 5x9 76 3" 7515-8276-86
1x12 2x10 5x10 89 3 1/2" 7515-8289-86
2-1_60
32
Extension drilling
T45 (1 3/4")
Dimensions Part No.
L D
mm ft in mm in
Light extension rod, T45 - Hex 38 - T45
3050 10' 38 1 1/2" 7325-4031-20
2-1_67
T45 D T 45
L
Flushing hole 16 mm.
T 45 T 45
L
T 45 D Thread
L
Wrench flat W
T 45 Thread
L
Shank adapter
See page 63
33
Extension drilling
T51 (2")
Coupling
sleeve Extension rod Guide tube
Button bit
Button bit,
2-1_503
34
Extension drilling
T51 (2")
Dimensions Part No.
L D
mm ft in mm in
Guide tube
Thread
Bit dia. mm
2-1_429
89-102 1830 6' 76 3" 7957-7618-20
89-102 3660 12' 76 3" 7957-7637-20
T 51 102-127 3660 12' 87 3 1/2" 7957-8737-20
T 51 D
L
Female end OD 76 / 87 mm.
T 51 D T 51
L
Flushing hole 21.5 mm. Wrench flat 45 mm.
T 51 T 51
L
Thread
T 51 D
L
Wrench flat 44.5
T 51 Thread
L
Shank adapter
See page 63
35
Extension drilling
Sandvik 60 (ST58 127 mm holes)
MF- rod Guide tube
Button bit,
2-1_504
Button bit,
MF- rod MF- rod Retrac
ST58 D ST58
L
Female end OD 80 mm.
Shank adapter
See page 63
36
Extension drilling
Sandvik 60 (>127 mm holes, ST68 bit thread)
2-1_512
ST 58 D ST 68
L
Female end OD 87 mm
D ST58
ST58 L
Flushing hole 22.5 mm.
Female end OD 80 mm
ST 68 ST 68
D
L
Shank adapter
See page 63
37
Extension drilling
Underground tube drilling tools T45 (1 3/4")
2-1_478
T 45 T 45
L
Flushing hole 18 mm.
Shank adapter
See page 63
38
Extension drilling
Underground tube drilling tools ST58 (2 1/4")
Button bit
2-1_479
Reaming bit
D1 D
39
Extension drilling
Underground tube drilling tools ST58 (2 1/4")
Dimensions Part No.
L D
mm ft in mm in
Drill tube, ST58 - Round 76 - ST58
1525 5' 76 3" 7378-7615-25
1525 5' 76 3" 7378-7615-45 1)
2-1_351
1830 6' 76 3" 7378-7618-25
1830 6' 76 3" 7378-7618-45 1)
ST 58 D ST 58
L
Flushing hole 26 mm.
1) Permanent back flow valve.
Shank adapter
See page 63
40
Extension drilling
Underground tube drilling tools ST68 (2 3/4")
Button bit
2-1_484
Reaming bit
Collaring bit
3x18 8x16 9x16 35 152 6" 7529-6652-S45
2-1_357C
41
Extension drilling
Underground tube drilling tools ST68 (2 3/4")
Buttons, mm Dimensions Bit Part No.
Front Gauge D D1 classi-
No Size No Size Angle mm mm fication
Reaming bit
4x14 8x14 35 152 95 7529-5652C-S65
4x14 8x14 35 152 102 7529-5652-S65
2-1_445
D1 D
ST 68 ST 68
D
L
FLushing hole 30 mm.
1) Permanent back flow valve.
Shank adapter
See page 63
42
Drifting and tunnelling
Page
CONTENTS
Code information ............................................................ 45
Button bits, cemented carbide grade MP 45 with spherical buttons ........................................................................................ xxxx-xxxx-S45
Button bits, cemented carbide grade MP 45 with semi-ballistic buttons .................................................................................. xxxx-xxxx-R45
Button bits, cemented carbide grade DP 65 with spherical buttons......................................................................................... xxxx-xxxx-S65
45
Drifting and tunnelling
R25 (1") bit thread
Shank rod
Button bit
Coupling
2-1_407
Reaming
equipment
D
1x5 2x5 41 1 5/8 7732-1441-42
R28 D R25
L
Flushing hole 9.1 mm.
Packing
25 R 25
D 795-1811
159 L
Flushing hole 8.8 mm. For flushing tube 8 mm.
46
Drifting and tunnelling
R25 (1") bit thread
Dimensions Part No.
L D
mm ft in mm in
Coupling sleeve
Thread
R32 150 5 29/32" 44 1 47/64" 7993-3644
2-1_17
D
4x10 8x10 30 89 3 1/2" 7722-4889-S45
Shank adapter
See page 63
47
Drifting and tunnelling
R28 (1 1/8") bit thread
Button bit
Coupling
2-1_408
Reaming
equipment
R32 D R28
L
Flushing hole 9.7 mm.
48
Drifting and tunnelling
R28 (1 1/8") bit thread
Dimensions Part No.
L D
mm ft in mm in
Drifter rod, R38 - Hex 28 - R28
3700 12' 1 1/2" 28 1 1/8" 7854-7637-20
2-1_340
4305 14' 1 31/64" 28 1 1/8" 7854-7643-20
R38 D R28
L
Flushing hole 9.1 mm.
Coupling sleeve
Thread
R32 150 5 29/64" 44 1 47/64" 7993-3644
2-1_17
D
4x10 8x10 30 89 3 1/2" 7722-4889-S45
Shank adapter
See page 63
49
Drifting and tunnelling
R32 (1 1/4") bit thread
MF-rod Button bit
Shank adapter
Coupling Cross bit
sleeve Drifter rod
Reaming
equipment
50
Drifting and tunnelling
R32 (1 1/4") bit Thread
Dimensions Part No.
L D
mm ft in mm in
Drifter rod, R38 - Hex 35 - R32
3090 10' 1 21/32" 35 1 3/8" 7854-9631-20
2-1_342
3700 12' 1 1/2" 35 1 3/8" 7854-9637-20
D R32 4305 14' 1 31/64" 35 1 3/8" 7854-9643-20
R38
L 4915 16' 1 1/2" 35 1 3/8" 7854-9649-20
5525 18' 1 33/64" 35 1 3/8" 7854-9655-20
Flushing hole 9.5 mm.
Coupling sleeve
R38 170 6 3/4" 55 2 5/32" 7994-3655
T38 191 7 1/2" 55 2 5/32" 7314-3355
2-1_361
51
Drifting and tunnelling
R32 (1 1/4") bit Thread
Buttons, mm Dimensions Part No.
Front Gauge D
No Size No Size Angle mm in
Reaming equipment for cut holes / Pilot adapter, 6 taper
Thread
D
R32 26 1 1/32" 7822-3526
2-1_116
D
4x10 8x10 30 89 3 1/2" 7722-4889-S45
52
Drifting and tunnelling
Sandvik Jumbo. R35 (1 3/8") bit thread
Reaming
equipment
Coupling sleeve
191 7 1/2" 55 2 5/32" 7314-3355
2-1_227
53
Drifting and tunnelling
Sandvik Jumbo. R35 (1 3/8") bit thread
Buttons, mm Dimensions Part No.
Front Gauge D
No Size No Size Angle mm in
Reaming equipment for cut holes / Pilot adapter, 12 taper
Thread
R35 40 1 37/64" 7821-5440
D
2-1_117
Shank adapter
See page 63
54
Drifting and tunnelling
Sandvik Extra. R35 (1 3/8") bit thread
Button bit
2-1_536
T 35 D T 35
L
Flushing hole 15 mm.
Female end OD 48,2 mm.
55
Drifting and tunnelling
Sandvik Extra. T35 (1 3/8") threaded shank adapters
Hammer Dimensions, mm Part No.
category Flushing tube Thread L
Shank adapter for Tamrock HL 550 SUPER / 560 SUPER / 510 S-45
45 TU T35 500 7307-7554-01
3-1_184
58.8
49
L 10
Shank adapter for Atlas Copco COP 1432, COP1440, COP1838 HD/ME
TU T35 435 7307-3652-01
38
3-1_127
54
84.5
L 9
58.7
49
L 7.9
56
Drifting and tunnelling
Sandvik CAPP standard bits
Sandvik CAPP standard bits for drifting and tunnelling are available in three basic designs.
Type 52
2-1_542
Type 53
2-1_543
Type 54
2-1_544
Options
Following options are available for non standard CAPP bits for drifting and tunnelling. When ordering non-standard products,
a letter that describes the option must be included in the Part No.
Example: An R32, CAPP 53, 45mm bit with an extra hole for side flushing, will get the Part No.: 7733-5345A-S45.
Note: If a bit has one hole for side flushing as standard, an A in the Part No. will give the bit one extra hole for side flushing,
e.g. the bit will have two holes for side flushing.
57
Reaming Equipment
Page
CONTENTS
Reaming equipment for cut holes .................................. 61
L D Part No.
mm ft in mm in
Reaming equipment for cut holes / Pilot rod, Hex 22, 6 taper
800 2' 7 1/2" 26 1 1/32" 7922-6108-11
1200 3' 11 3/4" 26 1 1/32" 7922-6112-11
1600 5' 3" 26 1 1/32" 7922-6116-11
2-1_112
D
4x10 8x10 30 76 3" 7722-4876-S45
4x10 8x10 30 89 3 1/2" 7722-4889-S45
61
Reaming Equipment
Buttons, mm Dimensions Part No.
Front Gauge D
No Size No Size Angle mm in
Reaming equipment for cut holes / Pilot adapter, 6 taper
Thread
R25 26 1 1/32" 7822-2526
D
R28 26 1 1/32" 7822-1526
2-1_116
R32 26 1 1/32" 7822-3526
D
4x10 8x10 30 89 3 1/2" 7722-4889-S45
62
Shank adapters
Page
CONTENTS
Code information ............................................................ 65
Furukawa ........................................................................ 73
Ingersoll-Rand ................................................................ 75
Montabert ....................................................................... 77
Tamrock .......................................................................... 79
Shank adapters (Shank rods), HEX 22, 4.5-5 mm flushing tube, packing.................................................................................. xxxx-xxxx-13
Shank adapters (Shank rods), HEX 25, 4.5-5 mm flushing tube, packing.................................................................................. xxxx-xxxx-14
Shank adapters (Shank rods), HEX 25, 8 mm flushing tube, packing ........................................................................................ xxxx-xxxx-20
65
Shank adapters
Dimensions, mm Part No.
3-1 15
4.5-5.0 R23 255 7807-6103-13
4.5-5.0 R25 255 7802-6103-13
108 L
Packing
Flushing hole 6.7 mm. 795-1831
Packing
795-1836
108 L
Flushing hole 8.6 mm.
Packing
795-1811
159 L
Flushing hole 8.6 mm.
66
Shank adapters
Atlas Copco
Dimensions, mm Part No.
Hammer
category Flushing tube Thread L
Atlas Copco BBC 43, 44, 45 and 100
TU 10 R32 380 7803-3100-30
31.7 32
3-1_26
48 Packing
795-1812
19 L 20.5
57.2
Packing
32 795-1812
L 25.4
80 Packing
L 13.4 795-1821
64.4
1) Split stop ring needed (machine part)
80
L 13.4
Packing
795-1806
53
Packing
136.7 795-1812
L
67
Shank adapters
Atlas Copco
Dimensions, mm Part No.
Hammer
category Flushing hole Thread L
Atlas Copco COP 125, 130 and 131
38.1 38.7
TU,BE,PD 14 T38 380 7304-4500-60
3-1_12
52 Packing
795-1821
32
L
58.4 Packing
795-1821
28.3
L
53
Packing
136.7 795-1812
L
53
123
L
53
123
L
74
L
74
L
68
Shank adapters
Atlas Copco
Dimensions, mm Part No.
Hammer
category Flushing hole Thread L
Atlas Copco COP 1032 HD
34 45 TU,BO R32 340 7803-3588-01
3-1_120
54
58
L 9
54
58
L 9
54
58 9
L
58
L 9
54
74
L 9
54
74
L 9
74 9
L
69
Shank adapters
Atlas Copco
Dimensions, mm Part No.
Hammer
category Flushing hole Thread L
Atlas Copco COP 1038 HL
34 38 BE,PD R32 575 7803-3593-01
BE,PD T38 575 7304-3593-01
3-1_125
54
74
L 9
3-1_125b
54
74
L 9
54
74
L 9
54 BE,PD/Tubes/
MF-rod T45 575 7305-3593-01
74
L 9
70
Shank adapters
Atlas Copco
Dimensions, mm Part No.
Hammer
category Flushing tube Thread L
Atlas Copco COP 1432, COP1440, COP1838 HD/ME
38 TU R38 435 7804-3652-01
TU T35 435 7307-3652-01
3-1_127
54 TU T38 435 7304-3652-01
84.5
L 9
84.5
L 9
54
84.5
L 9
71
Shank adapters
Atlas Copco and Boart
Dimensions, mm Part No.
Hammer
category Flushing tube Thread L
Atlas Copco COP 1550, COP 1838 ME/ HE
52 BE,PD T38 525 7304-3655-01
BE,PD T45 525 7305-3655-01
3-1_171
54 BE,PD T51 525 7306-3655-01
84.5 9
L
125
L 10
68
136
L 11.2
58.6
64
L 15.0
64
L 15.0
64 15.0
L
72
Shank adapters
Furukawa
Dimensions, mm Part No.
Hammer
category Flushing tube Thread L
Furukawa HD 150
37.7 BE R38 520 7804-4799-01
3-1_167
55
70 40
L 8.5
55.5 795-1830
60 18.2
L
Furukawa HD 190
37.7 TU R38 485 7804-4787-01
3-1_207
54.9
70 39.9
L 8.3
Furukawa PD 200R
BE 14 T38 484 7304-7581-60
44.2 44 BE 14 T45 484 7305-7581-60
3-1_139
71
Packing
795-1821
69 21
L
64.4
Packing
79 795-1830
L 13.6
Furukawa HD 609
35.7 44.8 BE T38 620 7304-4791-01
T45 620 7305-4791-01
3-1_182
56.9
75 9.9
L
73
Shank adapters
Gardner-Denver and Holman
Dimensions, mm Part No.
Hammer
category Flushing tube Thread L
Gardner-Denver PR 123
44.5 44.3 TU,BE 14 R32 330 7803-7500-61
TU,BE 14 R38 350 7804-7500-60
3-1_43
55.5 TU,BE 14 T38 446 7304-7500-60
TU,BE 14 T45 446 7305-7507-60
64 TU,BE 14 T38 380 7304-7543-60
L 18.2
Packing
795-1821
Gardner-Denver PR 133
44.5 44.3 BE 16 T45 446 7305-7500-80
3-1_113
55.5 Packing
795-1830
60 18.2
L
Gardner-Denver HPR 1
49 44.5 TU,BE R38 595 7804-4882-01
TU,BE T38 595 7304-4882-01
BE T45 560 7305-4880-01
3-1_209
47.5
95.5
L
Gardner-Denver HPR 1H
44,5 44,5 BE T45 725 7305-4883-01
3-1_129
66
89
L
Gardner-Denver HPR 2
50.6 BE T51 916 7306-4885-01
76
3-1_197
50.7
102
L
Holman S115R
44.5 44.3 BE 14 R32 330 7803-7500-61
BE 14 R38 350 7804-7500-60
3-1_43
64 Packing
L 18.2 795-1821
74
Shank adapter
Ingersoll-Rand
Dimensions, mm Part No.
Hammer
category Flushing tube Thread L
Ingersoll-Rand URD 475, URD 550, VL120, EVL 130, VL140 and F16
44.5 44.3 BE 14 R32 330 7803-7500-61
BE 14 R38 350 7804-7500-60
3-1_43
55.5 BE 14 T38 380 7304-7543-60
BE 14 T38 446 7304-7500-60
64 BE 14 T45 446 7305-7507-60
L 18.2
Packing
795-1821
Ingersoll-Rand VL 140
44.5 44.3 BE R38 507 7804-4886-01
3-1_113
55.5
60 18.2
L
Ingersoll-Rand YH 65, YH 80
BE 16 T45 446 7305-7500-80
3-1_135
64.3 Packing
795-1830
46 45
85
L 13.5
Ingersoll-Rand YH 95
53 51 BE 19 T38 500 7304-7525-19
BE 19 T45 500 7305-7525-19
3-1_137
74
Packing
90 12
L
Ingersoll-Rand YH 95 RPS
53 51 795-1864
3-1_138
74
104
12
L
75
Shank adapter
Ingersoll-Rand, Joy, Klemm and Le Roi
Dimensions, mm Part No.
Hammer
category Flushing tube Thread L
Ingersoll-Rand YH 110 VRP
54.9 BE T51 840 7306-4975-01
74
3-1_191
52.9
125 12
L
60.5 Packing
795-1830
57
L 10.5
Klemm 4053
56.3 BE R55 500 7805-6015 1)
BE R55 500 7805-7015 2)
3-1_214
74
56.5 1) RH-Rotation
154
8.5 2) LH-Rotation
L
76
Shank adapters
Montabert
Dimensions, mm Part No.
Hammer
category Flushing tube Thread L
Montabert HC40
BE R32 447 7803-4725-01
38.1
BE R38 447 7804-4725-01
3-1_82
52.7
58 8.4
L
52.7
58 8.4
L
Montabert HC40
TU R32 372 7803-4721-01
3-1_161
52.7
32
58 8.4
L
52.7
TU T38 440 7304-4720-01
TU T38 500 7304-4723-01
97
L 8.4
Montabert H 100
44.4 BE 14 R38 447 7804-7502-60
44.6
BE 14 T38 537 7304-7502-60
3-1_31
Packing
80 795-1821
L 13.4
64.4
Packing
795-1821
80
L 13.4
44.4 44.6
BE R38 537 7804-7505-01 1)
3-1_2
64.4
Packing
795-1806
77
Shank adapters
Montabert and SIG
Dimensions, mm Part No.
Hammer
category Flushing tube Thread L
Montabert HC 120, HC 150
BE T38 490 7304-7520-01
45 Tubes T45 490 7305-7520-01
3-1_140
59.7
95
L 9.4
59.7
102
L 9.4
74 9
L
54
58
L 9
54
58
L 9
54
58
L 9
SIG 101
38 BE R32 500 7803-3591-01
34
3-1_123
54
74
L 9
78
Shank adapters
Tamrock
Dimensions, mm Part No.
Hammer
category Flushing tube Thread L
Tamrock HL 300
BE R32 400 7803-7549-01
32
3-1_141
58.8
39
L 10
Tamrock HL 300S
BO,TU R28 245 7809-7547-01
45
BO,TU R32 245 7803-7547-01
3-1_142
58.8
39
L 10
48 Packing
795-1812
20 20.5
L
37 Packing
25.7
L 795-1819
57
37
L 25.7
79
Shank adapters
Tamrock
Dimensions, mm Part No.
Hammer
category Flushing tube Thread L
Tamrock HL 500-45 / 510-45
BE R32 550 7803-7557-01
3-1_168
58.8 BE T35 550 7307-7557-01
BE T38 550 7304-7557-01
49 45 BE T45 550 7305-7557-01
L 10
58.8
58
L 10
Tamrock HLX 5
45
TU R32 500 7803-7585-01
TU T35 500 7307-7585-01
3-1_212
49
L 7.9
Tamrock HL 600-52
39.8 BE T45 650 7305-7551-01
BE T51 650 7306-7551-01
3-1_172
60
75 52 10
L
80
Shank adapters
Tamrock
Dimensions, mm Part No.
Hammer
category Flushing tube Thread L
Tamrock LP 600
PD R32 430 7803-7558-01
38
3-1_208
58.8
49
L 10
79
55.8 120
L 14
Tamrock HL 645
43.8 45 BE T38 600 7304-7541-01
BE T45 600 7305-7541-01
3-1_109
59
68
L
Tamrock HL 645 S
43.8 45 PD T38 525 7304-7540-01
PD T45 525 7305-7540-01
3-1_109
59
68
L
69
95
12.9
L
81
Shank adapters
Tamrock
Dimensions, mm Part No.
Hammer
category Flushing tube Thread L
Tamrock HL 700 S-65 Tube drilling
PD T45 600 7305-7574-01
65
3-1_193B
69
95
12.9
L
Tamrock HL 850
47.4 52 Tubes , PD 19 T45 500 7305-7400-19
BE 19 T45 590 7305-7402-19
3-1_110
Packing
80
14 795-1864
L
Tamrock HL 850S
47.4 52 BE, PD T38 670 7304-7400-01
Tubes, BE, PD T45 670 7305-7400-01
3-1_111
80
14
L
75
L 14
Tamrock HL 1000-60
BE ST58 670 7358-6014-01
60
3-1_133B
79
75
L 14
79
75 80
L 14
79
75 80
L 14
82
Shank adapters
Tamrock
Dimensions, mm Part No.
Hammer
category Flushing tube Thread L
Tamrock HL 1000 PE-52
BE T51 840 7306-6019-01
52
3-1_186
79
136 14
L
79
111.5
14
L
79
111.5
14
L
79
111.5 14
L
79
3-1_195
170 14
L
83
Shank adapters
Secoma and Toyo
Dimensions, mm Part No.
Hammer
category Flushing tube Thread L
Secoma Hydrastar 200
45 TU,BO R32 351 7803-4703-01
34
3-1_130
54
90 9
L
74 9
L
74
L 9
Toyo PR 220
44.5 44.3 BE 14 R32 330 7803-7500-61
BE 14 R38 350 7804-7500-60
3-1_43
55.5 Packing
795-1830
60 18.2
L
84
Foundation drilling equipment
Page
CONTENTS
Overburden drilling equipment, OD72 ............................ 87
Shank adapter
Pilot bit
Coupling sleeve
Adapter sleeve Tube coupling Extension tube Extension rod
Extension tube
1120 3' 8 1/8" 103 4 1/16" 7985-6012
2950 9' 8 1/8" 103 4 1/16" 7985-6031
4-1_22
C 89 C 89
L
Tube coupling
100 3 15/16" 103 4 1/16" 7989-6003
100 3 15/16" 103 4 1/16" 7989-6203 1)
4-1_23
C 89 C 89
L
Wrench flat 90 mm. 1) With cutting outlet
87
OD equipment (BBE 56/57)
OD 72 (3 1/2")
Dimensions Part No.
L D
mm ft in mm in
Extension, R38 - Round 39 - R38
D 280 11 1/32" 39 1 1/2" 7854-4302-20
4-1_70
L
Wrench flat 32 mm.
2-1 48
R 38 D R 38
L
Wrench flat 32 mm.
TR 110 x 24 C 89
L
Wrench flat 140 mm.
88
OD equipment (BBE 56/57)
OD 72 (3 1/2")
Dimensions Part No.
L D
mm ft in mm in
Shank adapter, for separate flushing
Thread
R38F 633 24 7/8" 7981-7003
4-1_121
Packing
TR 110 x 24 795-1821
L
For rock drill BBE 56U2 and BBE 57-01.
Flushing tube 14 (9/16").
Packing
795-1821
TR 110 x 24
L
Flushing tube 14 (9/16").
4-1_31
D
L
4-1_31
D
L
D
4-1_33
89
OD equipment (BBE 56/57)
OD 92 (4 3/8")
Flushing device Extension rod
Tube coupling Ring bit
4-1_435A
Shank adapter
Pilot bit
Adapter sleeve
Tube coupling Extension tube Extension rod
Extension tube
1100 3' 7 5/16" 124 4 7/8" 7985-6112
2930 9' 7 23/64" 124 4 7/8" 7985-6131
4-1_22B
C 110 C 110
L
Tube coupling
120 4 47/64" 124 4 7/8" 7989-6103
120 4 47/64" 124 4 7/8" 7989-6503 1)
4-1_23B
C 110 C 110
L
Wrench flat 110 mm.
1) With cutting outlet.
90
OD equipment (BBE 56/57)
OD 92 (4 3/8")
Dimensions Part No.
L D
mm ft in mm in
Extension, T45 - Round 46 - T45
D Thread
4-1_70B
T 45 T 45
L
Wrench flat 38 mm.
D T 45
T 45
L
Flushing hole 18 mm. Female end OD 71 mm.
Wrench flat 38 mm.
TR 125 x 24 C 110
L
Wrench flat 155 mm
91
OD equipment (BBE 56/57)
OD 92 (4 3/8")
Dimensions Part No.
L D
mm ft in mm in
Shank adapter, for separate flushing
Thread
4-1_121B
T45F 633 24 7/8" 7981-7009
Packing
TR 125 x 24
795-1821
L
For rock drill BBE 56U2 and BBE 57-01.
Flushing tube 14 (9/16").
Packing
TR 125 x 24 795-1821
L
Flushing tube 14 (9/16").
4-1_31
D
L
4-1_31
D
L
D
4-1_33
92
Eccentric drilling equipment
TUBEX 76/127 for top hammers
4-1_82
Flushing device
Wall thickness
TUBEX 76 TUBEX 127 Casing extension
Seemles Steel Casing Seemles Steel Casing TUBEX 76 = 135 mm
O.D. max. 89mm (3.5") O.D. max. 142 mm (5.6")
I.D. min. 78mm (3.06") I.D. min. 128 mm (5.05")
TUBEX 127 = 645 mm
Min. wall thickness 4.8mm (.188") Min. wall thickness 6.4 mm (.25")
Welded or right hand flush joint Welded or right hand flush joint
threaded * threaded *
Extension rod
D Thread
R38 R38 76 280 11" 39 1 1/2" 7854-4302-20
4-1_70
93
Eccentric drilling equipment
TUBEX 76/127 for top hammers
Dimensions Part No.
L D
Thread TUBEX mm ft in mm in
Extension rod
R38 R38 76/127 1220 4' 39 1 1/2" 7854-4312-30
2-1_48
R38 R38 76/127 1830 6' 39 1 1/2" 7854-4318-30
R38 R38 76/127 2435 8' 39 1 1/2" 7854-4324-30
R 38 D R 38 R38 R38 76/127 3050 10' 39 1 1/2" 7854-4331-30
L
Flushing hole 15 mm. Wrench flat 32 mm.
Wing coupling
4-1_35 R38 R38 76 180 7 1/16" 76 3" 7994-3076
Coupling sleeve
R38 R38 76/127 170 6 11/16" 55 2 5/32" 7994-3655
2-1_228
4-1_67
L
4-1_67B
L
94
Eccentric drilling equipment
TUBEX 76/127 for top hammers
Dimensions Part No.
L D
Thread TUBEX mm ft in mm in
Spacer
76/127 62 2 7/16" 81 3 3/16" 7989-1505
L 4-1_38
L 4-1_73
L
Wrench flat 32 mm.
64.4
80
L 13.4
Packing
(2 pieces req.)
795-1806
Shank adapters for other rock drills. For central or separate flushing, male thread R38, T38 or T45
76/127 See page 63
Driving sleeve for shank adapters with male thread R38, T38 or T45
R38 R38 199 7 27/32" 83 3 17/64" 7989-1512
T38 R38 199 7 27/32" 83 3 17/64" 7989-1519
D T45 R38 205 8 5/64" 83 3 17/64" 7989-1517
L 4-1_72
95
Eccentric drilling equipment
TUBEX XL90/115 for top hammers with casing shoe
Flushing device
Wall thickness Adapter sleeve
Extension rod
Steel Casing
Wing coupling Reamer Pilot bit
Eccentric reamer
XL90 3x12 35 90 3 35/64" 82-090L-123A60
Reaming Dia. 123 4 27/32"
D
115 2x5 2x12 3x14 35 115 4 33/64" 7588-5452-40
Reaming Dia. 152 6 1/8"
4-1_69
Casing shoe
4-1_44 XL90 80 3 1/8" 101 3 31/32" 84-090D-00
Guide device
4-1_449
T51 XL90 275 10 13/16" 100 3 15/16" 80-9700-090D
D XL90
R51 115 270 10 5/8" 126 4 61/64" 7989-1616-10
L
D 115
4-1_450
L
Extension rod
T51 T51 XL90 770 2' 6 5/16" 52 2" 7326-5308C-30
4-1_37
Wing coupling
4-1_35 T45 T51 XL90 215 8 15/32" 100 4 21/64" 7316-6200
T51 T51 XL90 220 8 21/32" 100 4 21/64" 7316-6300
D
R51 T45 115 215 8 15/32" 127 5" 7315-4727
R51 T51 115 220 8 21/32" 127 5" 7316-4727
L
Coupling sleeve
T45 T45 XL90/115 210 8 1/8" 63 2 31/64" 7315-3363
2-1_228
4-1_67-XL90
L
97
Auxiliary Tools
Page
CONTENTS Wrenches, knock-off-tools and
drill steel straightener ................................................... 101
8-1_15
Hex 25 600 1' 11 5/8" 25 1" 795-1418
Hex 28 600 1' 11 5/8" 28 1 1/8" 795-2423
D L
D L
8-1_ 90
101
Auxiliary tools
Fishing tools and thread grease
Dimensions Part No.
D D1 L Thread
Rubrik 3sleeve
Fishing
D For catching
R22 Hex. rods 33 185 R22 795-1629
8-1_17
R22 coupling sleeves 35 225 R22 795-1630
R25 Hex. rods 39 215 R25 795-1631
R25 coupling sleeves 38 275 R25 795-1632
L
R28 Hex. rods/coupling sleeves 48 335 R28 795-1687
R32 round/Hex. rods/coupling sleeves 48 300 R32 795-1604
R38 round rods/coupling sleeves 60 353 R38 795-1605
T35 round rods/coupling sleeves 52 284 T35 795-1613
T38 round rods/coupling sleeves/MF-rods 60 353 T38 795-1607
T45 round rods/coupling sleeves/MF-rods 71 393 T45 795-1608
T51 round rods/coupling sleeves/MF-rods 80 440 T51 795-1609
S51 round rods/coupling sleeves/MF-rods 80 440 S51 795-1610
ST58 tubes 76 90 410 ST58 795-1698
ST58 60 rods 84 450 ST58 795-1689
ST68 tubes 87 102 410 ST68 795-1696
Fishing pike
8-1_18
D D1 For catching
R22 rods 1) 10 4 160 R22 795-1600
R25 rods 1) 12 4 200 R25 795-1601
R28 rods 1) 14.8 4 220 R28 795-1686
L R32 rods 1) 19.4 4 280 R32 795-1606
R38 rods 2) 18 8 237 R38 795-1611
T38 rods 2) 19.4 8 237 T38 795-1676
T45 rods 2) 25 8 275 T45 795-1681
S51 rods 2) 27 15 285 S51 795-1693
T51 rods 2) 27 15 285 T51 795-1690
ST58 tubes 76 2) 70 24 500 ST58 795-1699
1) Without flushing hole. ST58 60 rods 2) 50 20 440 ST58 795-1688
2) With flushing hole. ST68 tubes 87 2) 71 32 541 ST68 795-2600
92
8-1_
Thread grease
Can 4.5 kg 215 170 795-1960
Can 18.0 kg 300 380 795-1961
Tube 0.40 kg 53/57 235 795-1962
ROCK
DRILLI
TOOL NG
S
8-1_19
102
Auxiliary tools
Grinding templates and gauges
Part No.
For cross and chisel bit integrals, cross and X-bits up to 115 mm and motor drill steels
3 mm
Radius 80 mm
2 mm 795-1343
eel
Wh
eel
Integrals
Bits
el
80 70 60 50 40 30 20 10 0
Whe
8-1_89 10
110
Carbide
insert
For buttons up to 16 mm
9
D/3
8 7 6 795-1396
REDRESS WHEN FLAT IS
16
8-1_5
For OD-bits
SK
IV
VIN GL
E 795-1340
KE AN
L EL
HE
W
110
FOR "O.D."BITS
3/32"
2.4 mm
0
1/4"
8-1_6 10
1/2"
20 3/4"
1"
30
11/4"
40 11/2"
8-1_44
103
Grinding
Page
CONTENTS Sanbee and Sanflea ...................................................... 107
Part No.
Sanbee
Intended for grinding all kinds of button bits
8-1_53
Accessories optional
In line oiler 797-5747-50
Tools for O-ring replacement 797-5452
Cooling/tank unit, complete 797-5488-85
Technical data
Grinding gauge for button up to 16 mm 795-1396
Grinding cups See page 115-116
Air pressure ...................................... 6-8 bar
Air consumption ................................ 40-55 l/s
Spindle speed.................................... 19000 r.p.m.
Recommended lubricants
Flushing air pressure ........................ Max. 6 bar
Air tool oil, 1 litre 797-5870-90
Flushing water pressure ..................... Max. 6 bar
Water consumption............................ 5-6 l/min
Hose connections:
Air, air hose....................................... 12.5 mm (1/2") ID
Water, water hose.............................. 6.3 mm (1/4") ID
Dimensions: HxWxD mm.................... 150x450x130
Weight, without package and hose ..... 2.9 kg
Weight, with package and hose.......... 3.5 kg
Sanflea
Intended for grinding all kinds of button bits
(Max. button size 10 mm)
Accessories optional
In line oiler 797-5747-50
Tools for O-ring replacement 797-5452
Technical data
Cooling/tank unit, complete 797-5488-85
Grinding gauge for button up to 16 mm 795-1396
Air pressure ...................................... 6-8 bar
Grinding cups See page 115-116
Air consumption ................................ 16-17 l/s
Spindle speed.................................... 14000 r.p.m.
Flushing air pressure ........................ Max. 6 bar
Recommended lubricants
Flushing water pressure ..................... Max. 6 bar
Air tool oil, 1 litre 797-5870-90
Water consumption............................ 5-6 l/min
Hose connections:
Air, air hose....................................... 12.5 mm (1/2") ID
Water, water hose.............................. 6.3 mm (1/4") ID
Dimensions: HxWxD mm.................... 150x450x130
Weight, without package and hose ..... 2.9 kg
Weight, with package and hose.......... 3.5 kg
107
Grinding
Sanroc Mini P
Part No.
Sanroc Mini P
Intended for grinding all kinds of button bit.
It is capable of handling threaded and tapered
button bits upp to 127 mm and DTH button
bits up to 250 mm (max. shank 130 mm).
Accessories optional
Bit holder insert for retrac-bits compl. 797-5502-50
Guard cover 797-5510-06
Arm-locking mechanism, complete 797-5510-30
Pneumatic bit-locking system, complete 797-5510-40
Bit holder for large drill bits, complete 797-5510-20
Cooling/Flushing tank unit, complete, 10 l 797-5488-75
Mounting bracket (for drill rig) 797-5510-05
Air pressure reducing valve (max.28/min.7 bar) 797-5910-28
Assembly tools for O-ring replacement 797-5452
Grinding gauge for button up to 16 mm 795-1396
Grease gun 797-5870-20
Grinding cups See page 115-116
Service-exchange unit
Factory-reconditioned grinding head 797-5130-10
8 1 93
Recommended lubricants
Technical data Grease, 0.4 kg cartridge 797-5773-20
Gear oil, 1 liter 797-5870-10
Air pressure ..................................... Max. 13 bar/ Min. 6.5 bar Air tool oil, 1 liter 797-5870-90
Air consumption ................................ 40-60 l/sec
Water pressure ................................. Max. 8 bar/ Min. 4 bar
Water consumption............................ 2-4 l/min *
Rated power (motor) .......................... 1.7 kW
Electricity supply ............................... 24V DC, 5A
Coolant/flushing medium ................... Water
Air connection, air hose ..................... 20 mm (3/4") ID
Water connection, water hose ............ 9.5 mm (3/8") ID
Dimensions: HxWxD mm.................... 730x350x300
Weight ............................................. 43.5 kg
108
Grinding
Sanroc Mini H
Part No.
Sanroc Mini H
Intended for grinding all kinds of button bit.
It is capable of handling threaded and cone-type
button bits upp to 127 mm and DTH button
bits up to 250 mm (max. shank 130 mm).
Accessories optional
Bit holder insert for retrac-bits compl. 797-5502-50
Guard cover 797-5510-06
Arm-locking mechanism, complete 797-5510-30
Pneumatic bit-clamping device, complete 797-5510-40
Bit holder for large drill bits, complete 797-5510-20
Cooling/Flushing tank unit, complete, 10 l 797-5488-75
Mounting bracket (for drill rig) 797-5510-05
Air pressure reducing valve (max.28/min.7 bar) 797-5910-28
Assembly tools for O-ring replacement 797-5452
Grinding gauge for button up to 16 mm 795-1396
Priority flow divider for fixed pumps 797-5414-01
Grease gun 797-5870-20
Grinding cups See page 115-116
109
Grinding
Sanroc Mini E
Part No.
Sanroc Mini E
Intended for grinding all kinds of button bit.
It is capable of handling threaded and cone-type
button bits upp to 127 mm and DTH button
bits up to 250 mm (max. shank 130 mm).
Accessories optional
Bit holder insert for retrac-bits compl. 797-5502-50
Guard cover 797-5510-06
Arm-locking mechanism, complete 797-5510-30
Technical data Pneumatic bit-clamping device, complete 797-5510-40
Bit holder for large drill bits, complete 797-5510-20
Air pressure ..................................... Max. 13 bar/ Min. 4 bar Cooling/Flushing tank unit, complete, 10 l 797-5488-75
Air consumption ................................ 2-3 l/sec Mounting bracket (for drill rig) 797-5510-05
Water pressure ................................. Max. 8 bar/Min. 4 bar Air pressure reducing valve (max.28/min.7 bar) 797-5910-28
Water consumption............................ 2-4 l/min * Assembly tools for O-ring replacement 797-5452
Rated power (motor) .......................... 1.5 kW Grinding gauge for button up to 16 mm 795-1396
Coolant/flushing medium ................... Water Grease gun 797-5870-20
Air connection, air hose ..................... 9.5 mm (3/8") ID Grinding cups See page 115-116
Water connection, water hose ............ 9.5 mm (3/8") ID
Dimensions: HxWxD mm.................... 730x350x300
Weight ............................................. 43 kg Service-exchange unit
Factory-reconditioned grinding head 797-5130-10
* With cooling tank unit 0,2-0,3 l/min.
Recommended lubricants
Grease, 0.4 kg cartridge 797-5773-20
Gear oil, 1 liter 797-5870-10
110
Grinding
Sanroc Mini P/H/E Manual
Part No.
Sanroc Mini P/H/E Manual
Intended for grinding all kinds of button bit.
It is capable of handling threaded and cone-type
button bits upp to 127 mm and DTH button
bits up to 250 mm (max. shank 130 mm).
Technical data
Manual P Manual H Manual E Accessories optional
Guard cover 797-5510-06
Air pressure ....................... Max. 13 bar Max. 13 bar Max. 13 bar
Min. 6.5 bar Min. 4 bar Min. 4 bar Arm-locking mechanism, complete 797-5510-30
Air consumption .................. 40-60 l/sec 2-3 l/sec 2-3 l/sec Pneumatic bit-clamping device, complete 797-5510-40
Hydraulic pressure............... Max. 200 bar Bit holder for large drill bits, complete 797-5510-20
Min. 140 bar Cooling/Flushing tank unit, complete 797-5488-75
Oil consumption................... 12 l/min Mounting bracket (for drill rig) 797-5510-05
Water pressure ................... Max. 8 bar Max. 8 bar Max. 8 bar Air pressure reducing valve (max.28/min.7 bar) 797-5910-28
Min. 4 bar Min. 4 bar Min. 4 bar Assembly tools for O-ring replacement 797-5452
Water consumption.............. 2-4 l/min * 2-4 l/min * 2-4 l/min * Grinding gauge for button up to 16 mm 795-1396
Rated power (motor) ............ 1.7 kW 3 kW 1.5 kW Grease gun 797-5870-20
Air connection, hose ............ 3/4" 3/8" 3/8" Grinding cups See page 115-116
Water connection, hose ....... 3/8" 3/8" 3/8"
Dimensions: HxWxD mm...... 730x350x300 730x350x300 730x350x300
Weight ................................ 41 kg 38 kg 41 kg Service-exchange unit
Factory-reconditioned grinding head 797-5130-10
111
Grinding
Sanroc Multi
Part No.
Sanroc Multi
Intended for grinding all kinds of button bit.
It is capable of handling threaded and cone-type
button bits upp to 152 mm and DTH button
bits up to 280 mm (max. shank 150 mm).
Accessories optional
8-1_97 Bit holder insert for retrac-bits 797-5503-30
Pneumatic bit-clamping device, complete 797-5510-40
Holder for reamer, 12 797-5330-12
Technical data Cooling/Flushing tank unit, complete , 10 l 797-5488-75
Assembly tools for O-ring replacement 797-5452
Air pressure ..................................... Max. 13 bar/ Min. 6.5 bar Grinding gauge for button up to 16 mm 795-1396
Air consumption ................................ 5-6 l/sec Grease gun 797-5870-20
Rated power (motor) .......................... 1.5 kW Grinding cups See page 115-116
Water pressure.................................. Max. 8 bar/ Min. 4 bar
Water consumption............................ 2-4 l/min *
Coolant/flushing medium ................... Water Service-exchange unit
Air connection, air hose ..................... 9.5 mm (3/8") ID Factory-reconditioned grinding head 797-5130-10
Water connection, water hose ............ 9.5 mm (3/8") ID
Dimensions: HxWxD mm ................... 990x670x795
Weight ............................................. 95 kg Recommen ded lubricants
Grease, 0.4 kg cartridge 797-5773-20
Gear oil, 1 liter 797-5870-10
* With cooling tank unit 0,2-0,3 l/min.
112
Grinding
Sanroc Micro
Part No.
Sanroc Micro
Intended for grinding all sizes and types of
threaded button bits and DTH-bits up to 254 mm.
Max. bit shank 146 mm (5 3/4").
Accessories optional
Cooling/Flushing tank unit, complete 797-5488-60
Assembly tools for O-ring replacement 797-5452
Holder for reamer 12 797-5330-12
Air pressure reducing valve (max.28/min.7 bar) 797-5910-28
Grinding gauge for button up to 16 mm 795-1396
Grinding cups See page 115-116
Service-exchange unit
Factory-reconditioned Sanbee grinding motor 796-5110-15
8-1_82
Recommended lubricants
Grease, 0.4 kg cartridge 797-5773
Air tool oil, 1 litre 797-5870-90
Technical data
Pneumatic grinder
Air pressure ..................................... Max. 13 bar/ Min. 6 bar
Air consumption ................................ 60-85 l/sec
Spindle speed.................................... 19000 r.p.m.
Water consumption............................ 5-6 l/min
Dimensions: HxWxD mm ................... 705x335x370
Weight ............................................. 35 kg
Transport weight................................ 45 kg
113
Grinding
Sanroc Flexi
Part No.
Sanroc Flexi
Semi-automatic grinder, intended for grinding all
sizes and types of button bits, (DTH-bits up
to 508 mm).
Recommended lubricants
3 Grease, 0,4 kg cartridge 797-5773
1+4 Air tool oil, 1 litre 797-5870-90
2
8-1_79
Bit holder for clamping treaded bits or retrac shirt max. 100mm (4")
and DTH bits ranging from 35 to 254 mm. Max. shank 100mm (4")
114
Grinding
Grinding cups
7-8 mm 797-5272-08
9 mm 797-5272-09
10 mm 797-5272-10
Shank 9 mm.
11 mm 797-5272-11
12-13 mm 797-5272-12
14 mm 797-5272-14
115
Grinding
Grinding cups
7-8-9 mm 797-5356-08
10 mm 797-5356-10
11 mm 797-5356-11
12-13 mm 797-5356-12
14 mm 797-5356-14
Shank 8 mm. 16 mm 797-5356-16
* For older grinder remove O-ring before use (VS 200)
Sancup (black)
For redressing ballistic buttons
8-9 mm 797-5366-09
10 mm 797-5366-10
11 mm 797-5366-11
12-13 mm 797-5366-12
14 mm 797-5366-14
Shank 8 mm. 16 mm 797-5366-16
* For older grinder remove O-ring before use (VS 200)
116
Grinding
Sanroc Cross/Cross D
Part No.
Sanroc Cross/Cross D
Sanroc Cross are intended for frontal grinding
of cross bits up to 64 mm.
Recommended lubricants
NOTE! Grinding wheels and Air tool oil, 1 litre 797-5870-90
mandrels are not included. Grease, 0.4 kg cartridge 797-5773
117
Grinding
Sanroc Cross Duo
Part No.
Sanroc Cross Duo
Twin-mounted frontal grinding machine.
Intended for frontal grinding of cross bits
up to 64 mm.
Recommended lubricants
NOTE! Grinding wheels and Air tool oil, 1 litre 797-5870-90
mandrels are not included. Grease, 0.4 kg cartridge 797-5773
118
Grinding
Sanroc X
Part No.
Sanroc X
Twin-mounted frontal grinding machine.
Intended for frontal grinding of X-bits
up to 76 mm.
Recommended lubricants
Air tool oil, 1 litre 797-5870-90
Grease, 0.4 kg cartridge 797-5773
NOTE! Grinding wheels and
mandrels are not included.
119
Grinding
Accessories for Sanroc Cross M/MD, Sanroc Cross/D/Duo, Sanroc X
8-1_23
Straight wheel for gauge grinding 35-76 300 32 32 797-1100-32
Mandrel for manual bit holder, complete for Sanroc Cross/Cross Duo/Cross D and Sanroc X
For R22 (7/8") thread 797-6030-22
For R23 (29/32") thread 797-6030-23
For R25 (1") thread 797-6030-25
For R28 (1 1/8") thread 797-6030-28
8-1_101 For R32 (1 1/4") thread 797-6030-32
For R35 (1 3/8") thread 797-6030-35
For R38/T38 (1 1/2") thread 797-6030-38
For T45 (1 3/4") thread 797-6030-45
Pneumatic bit-holder, complete without mandrel for Sanroc Cross/Cross Duo/Cross D and Sanroc X
797-6020
8-1_99
120
Grinding
Accessories for Sanroc Cross M/MD, Sanroc Cross/D/Duo, Sanroc X
Part No.
Mandrel, complete for pneumatic bit holder, also for semi-automatic gauge-grinding unit
For R23 (29/32") thread 797-6020-23
For R25 (1") thread 797-6020-25
For R28 (1 1/8") thread 797-6020-28
8-1_103 For R32 (1 1/4") thread 797-6020-32
For R35 (1 3/8") thread 797-6020-35
For R38/T38 (1 1/2") thread 797-6020-38
For T45 (1 3/4") thread 797-6020-45
Wheel dresser
Wheel dresser, complete 796-1858
- Shaft (1 pcs) 1) 796-1862
- Bearing bushing (2 pcs) 1) 796-1863
- Screw (6 pcs) 1) 796-1865
8-1_37
- Cover (2 pcs) 1) 796-1866
- 1 set of dresser rollers 1) 796-1867
Integrals
Bits
el
80 70 60 50 40 30 20 10 0
Whe
8-1_89 10
110
Carbide
insert
121
Grinding
Sanroc ILP
Part No.
Sanroc ILP
Mobile, lightweight, pneumatic grinder.
Intended for frontal and gauge grinding of chisel
integral steels.
Accessories optional
Grinding wheels:
For dry grinding 797-1227-15
8-1_73
For wet grinding 797-1227-10
In line oiler 797-5747-50
Kit for grinding plug-hole drill steel steels 797-5489-50
Mounting bracket (for drill rig) 797-5330-91
Support for integral steels 797-5330-92
Grinding template for chisel bit 795-1343
Technical data Grinding template for plug-hole steels 795-1336
Cutting-edge radius.................... 80 mm
Cutting-edge angle..................... 110
W
8-1_80
D
D1 d D = 127 mm
W = 63 mm
d = 32 mm
D1 = 80 mm
w = 50 mm
w
Grinding wheel
122
Grinding
Sanroc ILH
Part No.
Sanroc ILH
Mobile, lightweight, hydraulic grinder.
Intended for frontal and gauge grinding of chisel
integral steel.
8-1_73C
Accessories optional
Grinding wheels:
For dry grinding 797-1227-15
For wet grinding 797-1221-10
Kit for grinding plug hole drill steels 797-5489-50
Mounting bracket (for drill rig) 797-5330-91
Support for integral steels 797-5330-92
Grinding template for chisel bit 795-1343
Grinding template for plug hole steels 795-1336
Technical data
Recommended lubricants
Hydraulic pressure...................... Max 200 bar/ Min. 140 bar Grease, 0,5 kg cartridge 797-8773
Oil flow consumption .................. 12 l/min
Air pressure ............................... Max 8 bar
Air consumption ......................... 5-10 l/sec
Rated power (motor) ................... 4 kW
Idling speed................................ 3700 r.p.m.
Hose connections:
Hydraulic, hydraulic hose ............ R 3/8" female thread
Air, air hose................................ 9.5 mm (3/8") ID
Water, water hose....................... 9.5 mm (3/8") ID
Dimensions: HxWxD mm............. 600x550x350
Grinding wheel dimensions.......... 127x63x32 mm
Cutting-edge radius.................... 80 mm
Cutting-edge angle..................... 110
W
8-1_80
D
D1 d D = 127 mm
W = 63 mm
d = 32 mm
D1 = 80 mm
w = 50 mm
w
Grinding wheel
123
Grinding
Sanroc IP
Part No.
Sanroc IP
Pneumatic grinder intended for frontal and
gauge grinding of chisel integral steels.
Accessories optional
Grinding wheels:
For dry grinding 797-1252-15
For wet grinding 797-1252-10
Inline oiler 797-5747-50
Support legs (Set 2 pcs) 797-5347
Grinding template for chisel bit 795-1343
Recommended lubricants
8-1_60 Air tool oil, 1 litre 797-5870-90
Technical data
Cutting-edge radius......................... 80 mm
Cutting-edge angle.......................... 110
W
8-1_80
D
D1 d D = 152 mm
W = 83 mm
d = 63.5 mm
D1 = 100 mm
w = 64 mm
w
Grinding wheel
124
Grinding
Sanroc IE
Part No.
Sanroc IE
Electric grinder intended for frontal and gauge
grinding of chisel integral steels.
Air pressure .................................... Max 8 bar/ Min. 6 bar 220-290 V 3 phases 60 Hz 796-5012-60
Air consumption .............................. 20-45 l/sec 380-480 V 3 phases 60 Hz 796-5012-61
Idling speed..................................... 4200 r.p.m. 550 V 3 phases 60 Hz 796-5012-65
Air motor......................................... 1.5 kW 600 V 3 phases 60 Hz 796-5012-66
Hose connections:
Air, air hose..................................... 12.5 mm (1/2") ID
Water, water hose............................ 9.5 mm (3/8") ID Accessories included in delivery
Weight inclusive of grinding wheel .... 38 kg Grinding wheel for dry grinding 797-1252-15
T - hexagon wrench 6 mm 797-5766-06
Cutting-edge radius......................... 80 mm Protective goggles 797-5771
Cutting-edge angle.......................... 110
Accessories optional
Grinding wheels:
W For dry grinding 797-1252-15
8-1_80 For wet grinding 797-1252-10
Water tray (plastic) 797-5346
Support legs (set 2 pcs) 797-5347
Grinding template for chisel bit 795-1343
D
D1 d D = 152 mm
W = 83 mm
d = 63.5 mm
D1 = 100 mm
w = 64 mm
w
Grinding wheel
125
Grinding
Sanroc IXP/IXH
Part No.
Sanroc IXP/IXH
Sanroc IXP/IXH are intended for frontal and
gauge grinding of integral steels vith 3 or 4
inserts and threaded or tapered bits.
Accessories optional
Grinding wheel, dry, 132 797-1185-28
Grinding wheel, dry, straight for gauge grinding 797-1101-32
Dressing template 4-inserts (cross bit) 797-6035-08
Technical data Sanroc IXP Sanroc IXH Dressing template 3-inserts 797-6035-23
Grinding template, cross bit 795-1343
Hydraulic pressure............................. Max.200 bar Spare rollers for wheel dresser 796-1867
Min. 140 bar Mounting bracket (for drill rig) 797-5330-91
Oil flow consumption ......................... 12 l/min
Air pressure ...................................... Max 8 bar For Tamrock Commander:
Min. 6 bar Hydraulic mounting kit, IXH 797-5775-20
Air consumption ................................ 40-60 l/sec
Rated power...................................... 1.7 KW 4.0 KW
Idling speed....................................... 3000 r.p.m. 3000 r.p.m. Recommended lubricants
Dimensions: Air tool oil (IXP), 1 litre 797-5870-90
Grinder (HxWxD mm)......................... 250x285x395 Grease (IXH), 0,4 kg cartridge 797-5773
250x240x395
Grinding wheel 132, DxWxd mm....... 200x28x32 200x28x32
Grinding wheel straight, DxWxd mm ... 200x32x32 200x32x32
Weight .............................................. 20 kg 18 kg
Air hose ............................................ 12.5 mm (1/2") ID
Hydraulic hose................................... R 3/8"
126
Grinding
Grinding wheels
D W d Part No.
Sanroc IXP/IXH (132)
W For cross bits 33-43 mm Dry 200 28 32 797-1185-28
Straight wheel for gauge grinding Dry 200 32 32 797-1101-32
D d
8-1_81
D W d D1 w Part No.
Sanroc ILP, ILH, IP and IE
W ILP/ILH Dry 127 63 32 80 50 797-1227-15
8-1_24 ILP/ILH Wet 127 63 32 80 50 797-1227-10
D W d D1 w Part No.
D
D1 d
127
Numerical index with weight table
Part No. Weight Package Page Part No. Weight Package Page
(kg) size (pcs) (kg) size (pcs)
128
Numerical index with weight table
Part No. Weight Package Page Part No. Weight Package Page
(kg) size (pcs) (kg) size (pcs)
129
Numerical index with weight table
Part No. Weight Package Page Part No. Weight Package Page
(kg) size (pcs) (kg) size (pcs)
130
Numerical index with weight table
Part No. Weight Package Page Part No. Weight Package Page
(kg) size (pcs) (kg) size (pcs)
131
Numerical index with weight table
Part No. Weight Package Page Part No. Weight Package Page
(kg) size (pcs) (kg) size (pcs)
132
Numerical index with weight table
Part No. Weight Package Page Part No. Weight Package Page
(kg) size (pcs) (kg) size (pcs)
133
Numerical index with weight table
Part No. Weight Package Page Part No. Weight Package Page
(kg) size (pcs) (kg) size (pcs)
134
Numerical index with weight table
Part No. Weight Package Page Part No. Weight Package Page
(kg) size (pcs) (kg) size (pcs)
135
Numerical index with weight table
Part No. Weight Package Page Part No. Weight Package Page
(kg) size (pcs) (kg) size (pcs)
136
Numerical index with weight table
Part No. Weight Package Page Part No. Weight Package Page
(kg) size (pcs) (kg) size (pcs)
7985-6012 25,10 10 87
7985-6031 69,70 10 87
7985-6112 3,00 10 90
7985-6131 86,00 10 90
7985-6315-25 28,00 10 38
7985-6318-25 32,00 10 38
7989-1230 13,40 1 97
7989-1240 12,45 1 97
137
Non standard products
The products shown in this catalogue are, with a few exceptions, stock standard items. Within our
standard range it is possible to find products suitable for the wast majority of drilling conditions.
Outside of this range we however undertake manufacturing of non standard products in order to solve
specific customer problems.
All our products are designed and manufactured in a computerized system incorporating the latest
CAPP (Computer Aided Process Planning) technology. If the requested product modifications are
within the parameters set by the program, a quotation for price, min quantity and delivery time will
be answered within 24 hours.
Integral drill steels can be ordered in lengths, shank/rod combinations, bit diameters and cemented
carbide grades outside of the catalogue standard range.
Extension rods, drill tubes and drifter rods with other thread/rod combinations, heat treatments
or lengths can be delivered upon request as well as shank adapters with threads and dimensions
outside of the standard.
For larger bits (> 64 mm) a number of modifications outside of standard are possible:
Bit diameter: Choice in mm-intervals between min and max limits for the
thread dimension.
Front design: Choice between Flat Face and Drop Centre design (>61mm).
No. of gauge buttons: No. depending on bit diameter and front design.
No. of flushing holes: Limited by the available space in the bit front.
No. of flushing grooves: Depending on No. of gauge buttons.
Side flushing: Option to add side flushing hole(s).
Frontal flushing grooves: Choice of front design determines the options.
Button shape: Choice between spherical and ballistic buttons.
Cemented carbide grade: Choice between Multi Purpose and Dual Property grades.
Partly limited by the choice of button shape.
Gauge button diameter: Choice within max and min values for the bit diameter and
front design.
Front button diameter: Choice within max and min values for each bit diameter
and front design.
Bit skirt design: Choice between Normal and Retrac design (>51 mm).
Thread: Choice between threads available for the specific bit diameter.
All non-standard products generated within our CAPP system are guaranteed to have the same product
quality as the products in our standard product range.
138
How to select cemented carbide grade
MP 45 is the basic Sandvik cemented carbide grade used for most drilling conditions. Hence, this
should be the first choice, especially when drilling in rock not fully known. A spherical insert made of
the MP (Multi-Purpose) grade has a toughness/wear resistance ratio which is optimised to withstand
both high loads and wear.
DP 55 is a grade that has a wear resistance similar to MP 45 but offers higher toughness. It is speci-
ally suited for semi-ballistic inserts to accommodate the higher loads the inserts may be exposed to
because of their longer protrusion.
DP 65, on the other hand, has a similar toughness as MP 45, but a considerably higher wear resistance.
This grade should be the obvious choice when drilling in very abrasive rock with large, spherical
inserts.
DP65
Ca
rbi
de
fai
lur
es
Excessive wear
DP55
s
ure
9-6/161
l
fai
rb ide
Ca
MP45
139
Safety information
Grinding
Rubrik 3 of Cemented Carbide
Grinding or heating a cemented carbide product will produce dust or fumes of hazardous ingredients
which can be inhaled, swallowed or come in contact with the skin or eyes.
The limiting ingredient in cemented carbide is, from a health and safety point of view, Cobalt. Another
hazardous ingredient is Tungsten Carbide.
Cobalt is classified as harmful - may cause sensitization by inhalation or skin contact. Inhalation or skin
contact may also cause irritation.
Sensitive persons may experience an allergic reaction. Repeated inhalation of aerosols containing
Cobalt may cause obstruction in the respiratory organs. Long term inhalation of increased
concentrations may cause permanent disease.
Precautions
140