Beruflich Dokumente
Kultur Dokumente
Features
Modular pluggable technology, easy tool onsite maintenance;
Honeycomb briquette burning effect and the whole structure cooling
technology;
Double-coupling IP68 protection, highest waterproof level;
Metal structure, high mechanical strength;
Ergonomic light distribution to achieve uniform illuminating effect;
Free modular serialization and full power range solution.
Applications
Street lighting
Parking lots
Roadway lighting
Path lighting
Standard Colors
White
Gray
Black
Advantages
Driving Luminous
Input Voltage Flux Power Power
Model Current Power (W) Efficacy Beam Angle LED Brand CCT (K) CRI
(V) (lm) Factor Efficiency
(mA) (lm/W)
Lumen Pole
Working Storage Housing
Model Maintenance Diameter Product Size (mm) Packing Size (mm) N.W (kg) G.W (kg)
Environment Temperature Material
(h) (mm)
4
Lighting Distribution
T1A
Dimensions
850
775
695
595
490
T1A T1A-1
T1A
T1A-2 T1A-3 T1A-4
1110
1030
1110
1030
915
850
850
775
775
695
Step 1: Loosen the 2 screws at the rear cover, then remove the rear cover;
Step 2: Loosen the 4 screws on the 2 arched clamps, insert and fix the cross arm under the 2 arched clamps, and then
tighten the 4 screws;
Step 3: Connect the wires to the AC wires.(The earth wire should be reliable and linked to the ground);
Step 4: Fix the rear cover back to the lamp and tighten the 2 screws on it.
Maintenance
Step 1: Loosen the 2 screws at the back cover, then open the back cover;
Step 2: Loosen the screws at both ends of the failed module(s)/driver(s);
Step 3: Disconnect the waterproof connectors to the failed module(s)/driver(s);
Step 4: Take out the failed module(s)/driver(s);
Step 5: Replace the failed module(s)/driver(s) with qualified one(s),and then tighten the screws at the ends and the waterproof connectors;
Step 6: Close the back cover and then tighten up the 2 screws on it.
Specifications
Street Light TT1A Series
Installation
1. Pull the two latches at side, then 2. Loosen the four screws on the 3. Connect the ground wire, neutral
open the cover. mounting bracket. wire and live wire to the AC input
(make sure it sufficiently grounded).
4. Insert the pole to the lamp after 5. Tighten up the screws on the 6. Close the cover, then press and
connecting the wire. mounting bracket. fasten the latches.
Specifications
Street Light T1A Series
Maintenance
Driver & Electrical Parts
1. Pull the two latches at side, then 2. Disconnect the driver from the AC 3. Unscrew the screws at ends of the
open the cover. input. driver.
4 Unscrew the waterproof connector to 5. Replace the failed driver with a new 6. Close the cover. Then press and
the driver one. Tighten up all the screws and the fasten the latches.
connector. Re-connect to the wires of
AC input.
Specifications
Street Light T1A Series
Module
1. Pull the two latches at side, then 2. Unscrew the two screws at ends of 3. Unscrew the waterproof connector to
open the cover. the failed module. the failed module.
4. Take out the failed module and 5. Align and tighten up the connector, 6. Close the cover. Then press and
replace with a new one. and the screws for the new module. fasten the latches.
Specifications
Street Light T1A Series
Spin the male terminal clockwise. When the male indicatrix points between indicatrix female #2 and #3, and the gap
between male and female terminals is extremely small, the connectors are well connected; otherwise, there will be risks in
its waterproof performance.
When the gap between male and female terminals is extremely small, if any looseness can be sensed, please spin the male
terminal clockwise until tight.