Beruflich Dokumente
Kultur Dokumente
1
JAWAHARLAL NEHRU TECHNOLOGICAL UNIVERSITY HYDERABAD
IV B.Tech. I Sem., I Mid-Term Examinations, September-2017
AUTOMOTIVE CHASSIS AND SUSPENSION
Objective Exam
Name: ______________________________ Hall Ticket No. A
Answer All Questions. All Questions Carry Equal Marks. Time: 20 Min. Marks: 10.
1. The effect of the weight of the body on the side members of the frame will be. [ ]
a) inclined bending b) horizontal bending c) vertical bending d) twisting
2. The member of supporting points needed to mount engine clutch gear box on the chassis frame is
[ ]
a) four b)three c)two d)one
3. The mounting used between engine gear box unit and frame are made of [ ]
a) stainless steel b) brass c) rubber d) wood
7. The leaf spring eye of the heavy vehicle is generally bushed with [ ]
a) stainless steel b) phosphor bronze c) cast iron d) High speed steel
10. The component used on the wheel cylinder to seal , the brake fluid is [ ]
a) dust cover b) piston c) cup d) spring
Cont..2
Code No: 117AU :2: Set No. 1
12. To allow trapped water to run out, we have to provide number of __________________ .
13. Zine coating on steel parts is provided to avoid rusting is known as ___________________________.
14. In feline , the present I.C. engine power unit on Automobiles will be replaced by __________________ .
17. The top surface of each leaf of the spring _______________________ to improve fatigue starength and
life.
18. The sum of the cornering force and slip angle is called __________________ .
19. When the top of wheel slants outward, the slant angle of wheel with vertical is called________ .
20. The minimum allowable limit of hand brake efficiency for any vehicle is ____________________ .
-oOo-
Code No:117AU Set No. 2
JAWAHARLAL NEHRU TECHNOLOGICAL UNIVERSITY HYDERABAD
IV B.Tech. I Sem., I Mid-Term Examinations, September-2017
AUTOMOTIVE CHASSIS AND SUSPENSION
Objective Exam
Name: ______________________________ Hall Ticket No. A
Answer All Questions. All Questions Carry Equal Marks. Time: 20 Min. Marks: 10.
4. The leaf spring eye of the heavy vehicle is generally bushed with [ ]
a) stainless steel b) phosphor bronze c) cast iron d) High speed steel
7. The component used on the wheel cylinder to seal , the brake fluid is [ ]
a) dust cover b) piston c) cup d) spring
8. The effect of the weight of the body on the side members of the frame will be. [ ]
a) inclined bending b) horizontal bending c) vertical bending d) twisting
9. The member of supporting points needed to mount engine clutch gear box on the chassis frame is
[ ]
a) four b)three c)two d)one
10. The mounting used between engine gear box unit and frame are made of [ ]
a) stainless steel b) brass c) rubber d) wood
Cont..2
Code No: 117AU :2: Set No. 2
11. In feline , the present I.C. engine power unit on Automobiles will be replaced by __________________ .
14. The top surface of each leaf of the spring _______________________ to improve fatigue starength and
life.
15. The sum of the cornering force and slip angle is called __________________ .
16. When the top of wheel slants outward, the slant angle of wheel with vertical is called________ .
17. The minimum allowable limit of hand brake efficiency for any vehicle is ____________________ .
19. To allow trapped water to run out, we have to provide number of __________________ .
20. Zine coating on steel parts is provided to avoid rusting is known as ___________________________.
-oOo-
Code No:117AU Set No. 3
JAWAHARLAL NEHRU TECHNOLOGICAL UNIVERSITY HYDERABAD
IV B.Tech. I Sem., I Mid-Term Examinations, September-2017
AUTOMOTIVE CHASSIS AND SUSPENSION
Objective Exam
Name: ______________________________ Hall Ticket No. A
Answer All Questions. All Questions Carry Equal Marks. Time: 20 Min. Marks: 10.
2. The leaf spring eye of the heavy vehicle is generally bushed with [ ]
a) stainless steel b) phosphor bronze c) cast iron d) High speed steel
5. The component used on the wheel cylinder to seal , the brake fluid is [ ]
a) dust cover b) piston c) cup d) spring
6. The effect of the weight of the body on the side members of the frame will be. [ ]
a) inclined bending b) horizontal bending c) vertical bending d) twisting
7. The member of supporting points needed to mount engine clutch gear box on the chassis frame is
[ ]
a) four b)three c)two d)one
8. The mounting used between engine gear box unit and frame are made of [ ]
a) stainless steel b) brass c) rubber d) wood
Cont..2
Code No: 117AU :2: Set No. 3
12. The top surface of each leaf of the spring _______________________ to improve fatigue starength and
life.
13. The sum of the cornering force and slip angle is called __________________ .
14. When the top of wheel slants outward, the slant angle of wheel with vertical is called________ .
15. The minimum allowable limit of hand brake efficiency for any vehicle is ____________________ .
17. To allow trapped water to run out, we have to provide number of __________________ .
18. Zine coating on steel parts is provided to avoid rusting is known as ___________________________.
19. In feline , the present I.C. engine power unit on Automobiles will be replaced by __________________ .
-oOo-
Code No:117AU Set No. 4
JAWAHARLAL NEHRU TECHNOLOGICAL UNIVERSITY HYDERABAD
IV B.Tech. I Sem., I Mid-Term Examinations, September-2017
AUTOMOTIVE CHASSIS AND SUSPENSION
Objective Exam
Name: ______________________________ Hall Ticket No. A
Answer All Questions. All Questions Carry Equal Marks. Time: 20 Min. Marks: 10.
3. The component used on the wheel cylinder to seal , the brake fluid is [ ]
a) dust cover b) piston c) cup d) spring
4. The effect of the weight of the body on the side members of the frame will be. [ ]
a) inclined bending b) horizontal bending c) vertical bending d) twisting
5. The member of supporting points needed to mount engine clutch gear box on the chassis frame is
[ ]
a) four b)three c)two d)one
6. The mounting used between engine gear box unit and frame are made of [ ]
a) stainless steel b) brass c) rubber d) wood
10. The leaf spring eye of the heavy vehicle is generally bushed with [ ]
a) stainless steel b) phosphor bronze c) cast iron d) High speed steel
Cont..2
Code No: 117AU :2: Set No. 4
11. The sum of the cornering force and slip angle is called __________________ .
12. When the top of wheel slants outward, the slant angle of wheel with vertical is called________ .
13. The minimum allowable limit of hand brake efficiency for any vehicle is ____________________ .
15. To allow trapped water to run out, we have to provide number of __________________ .
16. Zine coating on steel parts is provided to avoid rusting is known as ___________________________.
17. In feline , the present I.C. engine power unit on Automobiles will be replaced by __________________ .
20. The top surface of each leaf of the spring _______________________ to improve fatigue starength and
life.
-oOo-