Beruflich Dokumente
Kultur Dokumente
Introduction
An engine oil fulfills a number of crucial functions and failing in any one of them, may be catastrophic. A good
engine oil must be able to hold in suspension contaminants such as carbon (soot) particles, by-products of fuel
combustion, neutralize organic acids, protect against rust and corrosion and dissipate the heat generated from
the combustion cycle. And it must do all of these things under tremendous heat and pressure without
succumbing to fatigue. Yet the most important function of a lubricant is to lubricate and reduce friction.
This function is performed by the oil film formed between two moving parts and its load carrying ability and is
described as the oils viscosity. In the common engineering sense, viscosity is the resistance to flow or
thickness of a liquid. The viscosity decreases with an increase in temperature, hence the temperature at which
a viscosity is measured, must always be specified. There are several viscosity units but the one most frequently
used is the Centistoke (cSt), which is the derived unit of kinematic viscosity where 1 cSt = 1 mm/s.
In this system, two series of viscosity grades are defined those containing the letter W and those without it.
Grades with the letter W are intended for use at lower temperatures and are based on a maximum low
temperature viscosity and a maximum borderline pumping temperature, as well as a minimum viscosity at
100C. The low temperature viscosity is measured by means of a multi-temperature version of ASTM D2602.
This test describes the method for apparent viscosity of motor oils at low temperature using the Cold Cranking
Simulator. Viscosities measured by this method have been found to correlate with engine speeds developed
during low temperature cranking. Borderline pumping temperature is measured according to ASTM D3829. This
provides a measure of an oils ability to flow to the oil pump and provide adequate pressure during the initial
stages of operation. Oils without the letter
W, intended for use at higher temperatures, are based on the viscosity at 100C only. These are measured by
ASTM D445. Fig. 1 depicts the SAE J300 classification for engine oils.
Automotive Lubricant Viscosity Grades
Engine Oils SAE J 300
SAE Low Temperature Viscosities High-Temperature Viscosities
Cranking Pumping
Kinematic
Viscosity (mPa/s) (mPa/s) 2 High Shear Rate (mPa/s)
(mm /s)
Grade max at temp max at temp at 150C
at 100C
C C
min max min
0W 6200 at -35 60 000 at -40 3.8
5W 6600 at -30 60 000 at -35 3.8
10W 7000 at -25 60 000 at -30 4.1
15W 7000 at -20 60 000 at -25 5.6
20W 9500 at -15 60 000 at -20 5.6
25W 13 000 at -10 60 000 at -15 9.3
20 5.6 <9.3 2.6
30 9.3 <12.5 2.9
40 12.5 <16.3 2.9
40 12.5 <16.3 3.7
50 16.3 <21.9 3.7
60 21.9 <26.1 3.7
For non-winter grade oils, the kinematic viscosity is measured at a temperature of 100 C in units of mm/s or
the equivalent centistokes. Based on the range of viscosity the oil falls in at that temperature, the oil is graded as
SAE viscosity grade 20, 30, 40, 50, or 60. In addition, for SAE grades 20, 30, and 40, a minimum viscosity
measured at 150 C and at a high-shear rate is also required. The higher the viscosity, the higher the SAE grade
is.
Remember that for any oil, if temperature is increased, viscosity will decrease. See Fig. 2
Multigrade Oils
As opposed to monograde oils which cover a single requirement as stipulated by the SAE J300 classification
system, multigrade oils meet the requirements of more than one SAE grade and may therefore be suitable for
use over a wider temperature range than a monograde oil. Multigrade oils are made by blending a low-viscosity
oil with special additives called Viscosity Index Improver (VII) VII are additives which improve the
temperature/viscosity characteristics of oils. Oils containing these additives, combine the good starting and
friction properties of a thin oil at low temperatures with the good lubricating properties of a more viscous oil at
high temperatures. See Fig. 3
SAE 40
cSt
SAE 15W
SAE 15W40
T C
Conclusion
Multigrade oils are the preferred option for all modern engines.
Multigrade oils will keep equipment operating in an optimum viscosity range, and offer consistent response and
lubrication protection.
Monograde oils are an acceptable option if the equipment can provide excellent oil cooling and constant
temperature control.