Sie sind auf Seite 1von 3

viernes, 13 de junio de 2008

John Deere Transmission Controller Diagnostic Codes

Transmission Controller Diagnostic Trouble Codes And Calibration Codes

If you want to repair your John Deere machinies, you are needing all this information,
it is an valious information. READ IT.

Transmission controller diagnostic trouble codes will display when malfunction occurs.

NOTE:
When diagnostic trouble code appears, shut engine off and restart engine to check if
diagnostic trouble code is an intermittent problem. Investigate circuit failure
identified by diagnostic trouble code.

The diagnostic trouble code number is indicated by an F3 plus two other digits.

The letter F means that a fault has occurred. The number 3 means the transmission
controller has diagnosed a problem in the transmission area and has sent a diagnostic
trouble code to the controller window to be displayed.

The last two digits of diagnostic trouble code number indicate specific failures.

If the third digit of the diagnostic trouble code number is (1), it indicates that at
least one of the sensor voltage wires is less than 4.75 volts or more than 5.25 volts.

If the third digit of the diagnostic trouble code number is (2), it indicates that
battery voltage is less than 9 volts or more than 16.5 volts.

If the third digit of the diagnostic trouble code number is (3), it indicates a problem
with B2 FNR Sensor.

If the third digit of the diagnostic trouble code number is (4), it indicates a problem
with B5 Left and Right Steer Sensor.

If the third digit of the diagnostic trouble code number is (5), it indicates a problem
with B1 Decelerator Sensor.

If the third digit of the diagnostic trouble code number is (6), it indicates a problem
with B4 Transmission Speed Control Sensor.
If the third digit of the diagnostic trouble code number is (7 or M), it indicates a
problem with B7 Left Track Motor Speed Sensor.

If the third digit of the diagnostic trouble code number is (8 or N), it indicates a
problem with B3 Right Track Motor Speed Sensor.

If the third digit of the diagnostic trouble code number is (9), it indicates a problem
with B6 Hydrostatic Pump Speed Sensor.

If the third digit of the diagnostic trouble code number is (A or E), it indicates a
problem with B8 Rear (LH) Pump Pressure Control Pilot (PCP).

If the third digit of the diagnostic trouble code number is (C or D), it indicates a
problem with B9 Front (RH) Pump Pressure Control Pilot (PCP).

If the third digit of the diagnostic trouble code number is (P), it indicates a problem
with S20 Park Lock Lever Switch and/or S4 Brake Pedal Switch.

If the third digit of the diagnostic trouble code number is (H), it indicates a problem
with S3 Neutral Start Switch.

If the third digit of the diagnostic trouble code number is (J), it indicates the F3J4
diagnostic trouble code was displayed when exiting calibration with out completion.
Wrong harness. Wrong transmission controller, or when a new transmission controller
has been installed and not calibrated.

If the third digit of the diagnostic trouble code number is (K), it indicates a problem
with Y3 (RH) Motor Shift Solenoid.

If the third digit of the diagnostic trouble code number is (L), it indicates a problem
with Y4 (LH) Motor Shift Solenoid.

If the third digit of the diagnostic trouble code number is (R), it indicates a problem
with B27 Reverse Speed Ratio switch.

If the third digit of the diagnostic trouble code number is (T), it indicates a problem
with B4 Transmission Speed In Grip (SIG).

If the fourth digit of the diagnostic trouble code number is (0, 2, 3, or 5), a open
circuit, shorted circuit, or no feed back is indicated. Do not attempt calibration. See
diagnostic trouble codes.
If the fourth digit of the diagnostic trouble code number is (1 or 4), a calibration
error or circuit failure is indicated. Access main menu and select DIAG in
transmission controller. Compare calibrated values to real time values! If values don't
match RECALIBRATE.

NOTE:
If diagnostic trouble code (311, 314, 321, or 324) is displayed DO NOT CALIBRATE,
see diagnostic trouble codes.

If the fourth digit of the diagnostic trouble code number is (6, 7, 8, or 9), it is the
result of calibrating indicating there is a failure. The failure must be fixed before
calibrating again. See diagnostic trouble codes.

There are sixty two 62 Diagnostic Trouble Codes.

The following twenty two 22 Diagnostic Trouble Codes will display in transmission
controller window, will be stored in memory and the Check Diagnostic Trouble Code
light on the display monitor will be ON: F311, F314, F321, F324, F330, F331, F334,
F335, F340, F341, F344, F345, F3A0, F3A5, F3C0, F3C5, F3D0, F3D5, F3E0, F3E5,
F3H1, F3H4.

The following forty 40 Diagnostic Trouble Codes will display in transmission


controller window and will be stored in memory: F350, F351, F354, F355, F360, F361,
F364, F365, F370, F372, F373, F375, F380, F382, F383, F385, F390, F392, F393,
F395, F3P0, F3P5, F3M1, F3M4, F3N1, F3N4, F3J0, F3J1, F3J4, F3J5, F3K3, F3L3,
F3R0, F3R1, F3R4, F3R5, F3T0, F3T1, F3T4, F3T5

There are forty four 44 Calibration Codes.

The following forty four 44 Calibration Codes will display during calibration: F336,
F337, F338, F339, F346, F347, F348, F348, F356, F357, F358, F359, F366, F367,
F368, F369, F396, F397, F398, F399, F3A6, F3A7, F3A8, F3A9, F3E6, F3E7, F3E8,
F3E9, F3C6, F3C7, F3C8, F3C9, F3D6, F3D7, F3D8, F3D9, F3H6, F3H7, F3H8, F3H9,
F3T6, F3T7, F3T8, F3T9.

!CAL Displayed On Controller and Check Diagnostic Trouble Code Light Flashing
This displayed on the controller indicates that calibration was not completed

Das könnte Ihnen auch gefallen