Beruflich Dokumente
Kultur Dokumente
Tools and supplies needed include a Hand Drill with 1/8 drill bit, Hobby Knife,
and Super Glue or Two Part Epoxy Glue. Plus Fine Grit Hobby Files, Sand Paper,
or Sanding Pads which are handy for smoothing out the gate points where resin
or pewter entered the part during production.
1
MINIATURE ASSEMBLY GUIDE Miniatures Assembly Guide
2
Miniatures Assembly Guide JOVIAN FORCES
Jovian: Alexnader - Destroyer
Side / Rear View Underside View with 1/8 Drill Hole Location
drilling hole
You will need to drill the
hole in the underside
of the cargo section
centered on the pilot hole
of the part. Use a 1/8 Drill
bit in your hand-drill and
try to drill in as straight
as possible to just under
the center point of the
part. This will keep all the
assembled ships center
points roughly level on
the table.
3
JOVIAN FORCES Miniatures Assembly Guide
Side / Rear View Underside View with 1/8 Drill Hole Location
drilling hole
You will need to drill the hole in the
underside of the main hull section
centered on the pilot hole of the part. Use
a 1/8 Drill bit in your hand-drill and try
to drill in as straight as possible to just
under the center point of the part. This
will keep all the assembled ships center
points roughly level on the table.
4
Miniatures Assembly Guide JOVIAN FORCES
Jovian: Corsair - Frigate
Side / Rear View Underside View with 1/8 Drill Hole Location
drilling hole
You will need to drill the
hole in the underside
of the cargo section
centered on the pilot hole
of the part. Use a 1/8 Drill
bit in your hand-drill and
try to drill in as straight
as possible to just under
the center point of the
part. This will keep all the
assembled ships center
SG8: 2x Kinetic points roughly level on
Cannon and 2x the table.
Particle/Beam
Cannon Weapons Parts Assembly
Glue on the pewter parts
Extra Parts (engine fins, & weapons)
before gluing together all
the resin ship sections.
5
JOVIAN FORCES Miniatures Assembly Guide
Side / Rear View Underside View with 1/8 Drill Hole Location
6
Miniatures Assembly Guide JOVIAN FORCES
Jovian: Gagarin - Tender
Parts Assembly
Glue the three inner panels in
the sets of holes in the front
and back end cap parts as
desired. At the same time
position the 3 outer panels
in the groves of the end caps
making sure not to get any
glue in the groves, so they can
rotate. Glue on pewter engine
fins and habitat modules
before gluing together all the
resin ship sections.
Extra Part
7
JOVIAN FORCES Miniatures Assembly Guide
Side View with one of the 3 outer panels Side / Rear View with one of the 3 outer
rotated to the top. panels rotated to the top.
Inside Panel 1/8 Drill Hole Locations Acrylic Post added in drilled hole.
8
Miniatures Assembly Guide JOVIAN FORCES
Jovian: Godsfire - Command Carrier
Side / Rear View Underside View with 1/8 Drill Hole Location
Deployed Habitat
drilling hole
You will need to drill the hole in the
Section Extra Part underside of the rear hull section
centered on the pilot hole of the part.
Use a 1/8 Drill bit in your hand-drill
and try to drill in as straight as
possible to just under the center
point of the part. This will keep all
the assembled ships center points
roughly level on the table.
Parts Assembly
Glue on the pewter parts (upper
& lower tail fins and weapons)
before gluing together all the resin
ship sections. Option for closed or
deployed habitat section, select the
desired part for your Godsfire.
9
JOVIAN FORCES Miniatures Assembly Guide
Side / Rear View Underside View with 1/8 Drill Hole Location
drilling hole
You will need to drill the
hole in the underside
SG10: 1x Fuel Section of the cargo section
Extra Part centered on the pilot hole
of the part. Use a 1/8 Drill
bit in your hand-drill and
try to drill in as straight
as possible to just under
the center point of the
part. This will keep all the
assembled ships center
SG9: Habitat Section points roughly level on
the table.
SG10: 2x Single
Particle Cannon Parts Assembly
Glue on the pewter
Extra Parts parts (habitat modules
if section is used and
weapons) before gluing
together all the resin
ship sections. Option for
Habitat and Fuel sections
Resin, Pewter, & Acrylic Parts to be added if desired.
10
Miniatures Assembly Guide JOVIAN FORCES
Jovian: Javelin - Frigate
Side / Rear View Underside View with 1/8 Drill Hole Location
drilling hole
You will need to drill the hole in the
underside of the Javelin centered on the
pilot hole of the part. Use a 1/8 Drill bit
in your hand-drill and try to drill in as
straight as possible to just under the
center point of the part. This will keep
all the assembled ships center points
roughly level on the table.
Parts Assembly
Glue on the pewter weapon parts.
11
JOVIAN FORCES Miniatures Assembly Guide
Side / Rear View Underside View with 1/8 Drill Hole Location
drilling hole
You will need to drill the
hole in the underside
of the cargo section
centered on the pilot hole
of the part. Use a 1/8 Drill
bit in your hand-drill and
try to drill in as straight
as possible to just under
the center point of the
part. This will keep all the
assembled ships center
points roughly level on
the table.
Parts Assembly
Glue on the pewter parts
(engine fins, & habitat
modules) before gluing
together all the resin ship
sections.
12
Miniatures Assembly Guide JOVIAN FORCES
Jovian: Majestic - Fleet Carrier
Side / Rear View Underside View with 1/8 Drill Hole Location
drilling hole
You will need to drill the
hole in the underside
of the cargo section
centered on the pilot hole
of the part. Use a 1/8 Drill
bit in your hand-drill and
try to drill in as straight
as possible to just under
the center point of the
part. This will keep all the
assembled ships center
points roughly level on
the table.
SG4: 4x Fuel Pods
Extra Parts Parts Assembly
Glue on the pewter parts
(engine fins, weapons, &
habitat modules) before
gluing together all the
resin ship sections.
13
JOVIAN FORCES Miniatures Assembly Guide
Side / Rear View Underside View with 1/8 Drill Hole Location
drilling hole
You will need to drill the hole in the
underside of the cargo section centered
on the pilot hole of the part. Use a 1/8
Drill bit in your hand-drill and try to drill
in as straight as possible to just under
the center point of the part. This will
keep all the assembled ships center
points roughly level on the table.
Parts Assembly
Glue on the pewter weapon parts.
14
Miniatures Assembly Guide JOVIAN FORCES
Jovian: Valiant Strike - Cruiser
drilling hole
You will need to drill the hole in the underside of the
of the main hull section centered on the pilot hole of
the part for the straight up and down un-deployed
habitat section. Use a 1/8 Drill bit in your hand-drill
and try to drill in as straight as possible to just under
the center point of the part. This will keep all the
assembled ships center points roughly level on the
table. If you want the habitat section in its deployed
mode select one of the three pilot holes to drill for
desired angle.
SG3: 4x Cargo
Containers
Extra Parts
15
JOVIAN FORCES Miniatures Assembly Guide
Side / Rear View Underside View with 1/8 Drill Hole Location
drilling hole
You will need to drill the
hole in the underside
of the cargo section
centered on the pilot hole
of the part. Use a 1/8 Drill
bit in your hand-drill and
try to drill in as straight
as possible to just under
the center point of the
part. This will keep all the
assembled ships center
points roughly level on
the table.
SG7: 2x Reaction
Control & 2x Point Parts Assembly
Defense Extra Parts Glue on the pewter parts
(engine fins, weapons, &
habitat modules) before
gluing together all the
resin ship sections.
16
Miniatures Assembly Guide CEGA FORCES
CEGA: Appalachian - Cargo
Side / Rear View Underside View with 1/8 Drill Hole Location
drilling hole
You will need to drill the hole in
the underside of the center hull
cargo section centered on the
pilot hole of the part. Use a 1/8
Drill bit in your hand-drill and try
to drill in as straight as possible
to just under the center point of
the part. This will keep all the
assembled ships center points
roughly level on the table.
Parts Assembly
Glue on the pewter parts
(engines & weapon) before
gluing together all the resin ship
sections.
17
CEGA FORCES Miniatures Assembly Guide
Side / Rear View Underside View with 1/8 Drill Hole Location
drilling hole
You will need to drill the hole in the underside of
the main hull centered on the pilot hole of the part.
Use a 1/8 Drill bit in your hand-drill and try to drill
in as straight as possible to just under the center
point of the part. This will keep all the assembled
ships center points roughly level on the table.
Parts Assembly
Glue on the pewter parts (engines & weapon)
before gluing together all the resin ship sections.
18
Miniatures Assembly Guide CEGA FORCES
CEGA: Bricriu - Corvette
Side / Rear View Underside View with 1/8 Drill Hole Location
drilling hole
You will need to drill the hole in the
underside of the Bricriu centered on the
pilot hole of the part. Use a 1/8 Drill bit
in your hand-drill and try to drill in as
straight as possible to just under the
center point of the part. This will keep
all the assembled ships center points
roughly level on the table.
Parts Assembly
Glue on the pewter weapon parts.
19
CEGA FORCES Miniatures Assembly Guide
Side / Rear View Underside View with 1/8 Drill Hole Location
drilling hole
You will need to drill the hole in the
underside of the Chin centered on the pilot
hole of the part. Use a 1/8 Drill bit in your
hand-drill and try to drill in as straight as
possible to just under the center point of
the part. This will keep all the assembled
ships center points roughly level on the
table.
Parts Assembly
Glue on the pewter weapon and drone bay
parts before gluing together all the resin
ship sections.
20
Miniatures Assembly Guide CEGA FORCES
CEGA: Charon - Transport (Cargo)
Side / Rear View Underside View with 1/8 Drill Hole Location
drilling hole
You will need to drill the hole in the
underside of the habitat section centered
on one of the three pilot holes of the part.
Select the desired hole for the angle at
which you want the habitat section. Use
a 1/8 Drill bit in your hand-drill and try
to drill in as straight as possible to just
under the center point of the part. This
will keep all the assembled ships center
points roughly level on the table.
Parts Assembly
Glue on the pewter weapon parts before
gluing together all the resin ship sections.
21
CEGA FORCES Miniatures Assembly Guide
Side / Rear View Underside View with 1/8 Drill Hole Location
drilling hole
You will need to drill the hole in the underside of
SG1: Habitat Section the habitat section centered on one of the three
pilot holes of the part. Select the desired hole for
the angle at which you want the habitat section.
Use a 1/8 Drill bit in your hand-drill and try to
drill in as straight as possible to just under the
center point of the part. This will keep all the
assembled ships center points roughly level on
the table.
Parts Assembly
Glue on the pewter weapons and parts before
gluing together all the resin ship sections.
SG3: 4x Cargo
Containers
Extra Parts
22
Miniatures Assembly Guide CEGA FORCES
CEGA: Detroit - Fleet Support
Side / Rear View Underside View with 1/8 Drill Hole Location
drilling hole
You will need to drill the hole in the underside of the
Detroit hull centered on the pilot hole of the part.
Use a 1/8 Drill bit in your hand-drill and try to drill in
as straight as possible to just under the center point
of the part. This will keep all the assembled ships
center points roughly level on the table.
Parts Assembly
Glue on the pewter engine and weapon parts before
gluing together all the resin ship sections.
23
CEGA FORCES Miniatures Assembly Guide
Side / Rear View Underside View with 1/8 Drill Hole Location
drilling hole
You will need to drill the hole in the
underside of the Hachiman centered on
the pilot hole of the part. Use a 1/8 Drill
bit in your hand-drill and try to drill in
as straight as possible to just under the
center point of the part. This will keep
all the assembled ships center points
roughly level on the table.
Parts Assembly
Glue on the pewter engine and weapon
parts before gluing together all the
resin ship sections.
24
Miniatures Assembly Guide CEGA FORCES
CEGA: Hammerhead - Dreadnought
Side / Rear View Underside View with 1/8 Drill Hole Location
drilling hole
You will need to drill the hole in the
underside of the Hammerhead hull centered
on the pilot hole of the part. Use a 1/8
Drill bit in your hand-drill and try to drill
in as straight as possible to just under the
center point of the part. This will keep all the
assembled ships center points roughly level
on the table.
Parts Assembly
Glue on the pewter engine and weapon
parts before gluing together all the resin
ship sections.
25
CEGA FORCES Miniatures Assembly Guide
Side / Rear View Underside View with 1/8 Drill Hole Location
drilling hole
You will need to drill the hole in the
underside of the cargo section centered
on the pilot hole of the part. Use a 1/8
Drill bit in your hand-drill and try to drill
in as straight as possible to just under
the center point of the part. This will keep
all the assembled ships center points
roughly level on the table.
Parts Assembly
Glue on the pewter weapon part before
gluing together all the resin ship sections.
26
Miniatures Assembly Guide CEGA FORCES
CEGA: Icarus - Transport (Fuel)
Side / Rear View Underside View with 1/8 Drill Hole Location
drilling hole
You will need to drill the hole in the
underside of the habitat section centered
on one of the three pilot holes of the part.
Select the desired hole for the angle at
which you want the habitat section. Use a
1/8 Drill bit in your hand-drill and try to drill
in as straight as possible to just under the
center point of the part. This will keep all the
assembled ships center points roughly level
on the table.
Parts Assembly
Glue on the pewter weapon parts before
gluing together all the resin ship sections.
27
CEGA FORCES Miniatures Assembly Guide
Side / Rear View Underside View with 1/8 Drill Hole Location
drilling hole
You will need to drill the hole in the
underside of the Narwal hull centered on
the pilot hole of the part. Use a 1/8 Drill
bit in your hand-drill and try to drill in
as straight as possible to just under the
center point of the part. This will keep
all the assembled ships center points
roughly level on the table.
Parts Assembly
Glue on the pewter engine and weapon
parts before gluing together all the resin
ship sections.
28
Miniatures Assembly Guide CEGA FORCES
CEGA: Poseidon - Battleship
Side / Rear View Underside View with 1/8 Drill Hole Location
drilling hole
You will need to drill the hole in the underside
of the habitat section centered on one of the
three pilot holes of the part. Select the desired
hole for the angle at which you want the habitat
section. Use a 1/8 Drill bit in your hand-drill
and try to drill in as straight as possible to just
under the center point of the part. This will
keep all the assembled ships center points
roughly level on the table.
Parts Assembly
Glue on the pewter engine and weapon parts
before gluing together all the resin ship
sections.
Side / Rear View Underside View with 1/8 Drill Hole Location
drilling hole
You will need to drill the hole in the
underside of the Tengu hull centered on
the pilot hole of the part. Use a 1/8 Drill
bit in your hand-drill and try to drill in
as straight as possible to just under the
center point of the part. This will keep
all the assembled ships center points
roughly level on the table.
Parts Assembly
Glue on the pewter parts.
30
Miniatures Assembly Guide CEGA FORCES
CEGA: Uller - Missile Cruiser
Side / Rear View Underside View with 1/8 Drill Hole Location
drilling hole
You will need to drill the hole in the
underside of the cargo section centered
on the pilot hole of the part. Use a 1/8
Drill bit in your hand-drill and try to drill
in as straight as possible to just under
the center point of the part. This will keep
all the assembled ships center points
roughly level on the table.
31
AVAILABLE PEWTER WEAPONS & PARTS PACKS Miniatures Assembly Guide
32
Miniatures Assembly Guide AVAILABLE EXTRA BASES, PARTS, DECALS, AND DICE
33
available acrylic bases for older 1/5000 scale ships Miniatures Assembly Guide
34
Miniatures Assembly Guide AVAILABLE CEGA & JOVIAN EXO-ARMOR AND FIGHTER SQUADS
35
CEGA & JOVIAN EXO-ARMOR AND FIGHTER SQUAD PARTS PHOTOS Miniatures Assembly Guide
Syreen Squad Pewter Parts and Hector Squad Pewter Parts and
Black or Clear Pastic Flight Base Black or Clear Pastic Flight Base
36
Miniatures Assembly Guide CEGA & JOVIAN EXO-ARMOR AND FIGHTER SQUAD PARTS PHOTOS
Fury Squad Pewter Parts and Retaliator Squad Pewter Parts and
Black or Clear Pastic Flight Base Black or Clear Pastic Flight Base
Cerberus Squad Pewter Parts and Pathfinder Squad Pewter Parts and
Black or Clear Pastic Flight Base Black or Clear Pastic Flight Base
Wyvern Squad Pewter Parts and Vindicator Squad Pewter Parts and
Black or Clear Pastic Flight Base Black or Clear Pastic Flight Base
37
CEGA & JOVIAN EXO-ARMOR AND FIGHTER SQUAD PARTS PHOTOS Miniatures Assembly Guide
Wyvern Marine Squad Pewter Parts & Pathfinder Recon Squad Pewter Parts
Black or Clear Pastic Flight Base & Black or Clear Pastic Flight Base
Wyvern Bomber Squad Pewter Parts & Pathfinder Sniper Squad Pewter Parts
Black or Clear Pastic Flight Base & Black or Clear Pastic Flight Base
Dragonstriker Squad Pewter Parts & Stormrider Squad Pewter Parts &
Black or Clear Pastic Flight Base Black or Clear Pastic Flight Base
38
Miniatures Assembly Guide examples of painted exo-armors
39
EXAMPLES OF PAINTED EXO-ARMORS Miniatures Assembly Guide
Syreen
Back Views
Fury
Front
Fury Back
Wyvern
Back Views
Cerberus Cerberus
Commander Stock
40
Recon Fighter Bomber Front
Miniatures Assembly Guide EXAMPLES OF PAINTED EXO-ARMORS
Pathfinder
Back Views
Vindicator
41
EXAMPLES OF PAINTED NEW 1/4000 SCALE SHIPS Miniatures Assembly Guide
42
Miniatures Assembly Guide PAINT SCHEMES EXAMPLES FROM OLDER 1/5000 SCALE SHIPS
example jovian paint schemes used on the older 1/5000 SCALE ships
We have not had time to get the new Jovian resin spaceships painted up yet. So here are some photos of the older
1/5000 scale Jovian Chronicles spaceships to use for paint scheme ideas when painting up your fleet.
43
PAINT SCHEMES EXAMPLES FROM OLDER 1/5000 SCALE SHIPS Miniatures Assembly Guide
example CEGA paint schemes used on the older 1/5000 SCALE ships
We have not had time to get the new CEGA resin spaceships painted up yet. So here are some photos of the older
1/5000 scale Jovian Chronicles spaceships to use for paint scheme ideas when painting up your fleet.
44
45
46